CHAUVET DJ LED Pinspot 3 Quick Reference Guide

Quick Reference Guide
QUICK REFERENCE GUIDE
EN

About This Guide

The LED Pinspot 3 Quick Reference Guide (QRG) has basic product information such as mounting and technical specifications.
The information and specifications contained in this QRG are subject to change without notice.

Safety Notes

These Safety Notes include important information about installation, use, and maintenance.
ONLY connect this product to a grounded and protected circuit.
DO NOT look at the light source when the product is on.
Make sure the power cord is not crimped or damaged.
!
Never disconnect this product from power by pulling on the cord.
When mounting this product overhead, ALWAYS use a safety cable.
DO NOT allow flammable materials close to the product when it is operating.
DO NOT touch the product’s housing when it is on because it will be hot.
The voltage of the outlet to which you are connecting this product must be within the range stated on the decal or rear panel of the product.
This product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose this product to rain or moisture.
Always mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
Be sure that no ventilation slots on the unit’s housing are blocked.
Never connect this product to a dimmer or rheostat.
Never carry the product by the power cord. Use only the handle to carry this product.
The maximum ambient temperature is 104 °F (40 °C). Do not operate this product at higher temperatures.
In the event of a serious operating problem, stop using immediately.
DO NOT open this product. It contains no user-serviceable parts.
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.

Contact

Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux, contact your distributor to request support or return a product. Visit www.chauvetdj.com for contact information.

What is Included

LED Pinspot 3
5-Pack of Colored Gels
Hanging Bracket with Mounting Hardware
Warranty Card
Quick Reference Guide

To Begin

Unpack your LED Pinspot 3 and make sure you have received all parts in good condition. If the box or contents appear damaged, notify the carrier immediately, not Chauvet.
1
LED Pinspot 3 QRG Rev. 3
QUICK REFERENCE GUIDE

Product Description

The LED Pinspot 3 is a compact, palm-sized spotlight that offers easily controllable dimming with the optional IRC-6 remote. Change the color with the included 5-pack of gels.

Overview

EN
Infrared Sensor Power Cable
Lens
Gel Clip

Dimensions

4.6 in
116.5 mm
2.7 in
68 mm
4.1 in
104 mm

AC Power

This product has an auto-ranging power supply that works with an input voltage range of 100 to 240 VAC, 50/60 Hz.
To eliminate wear and improve its lifespan, during periods of disuse completely disconnect the
!
product from power via breaker or by unplugging it.

Mounting

Before mounting this product, read the Safety Notes.

Mounting Diagram

Mounting Clamp
(such as CLP-15N from Chauvet)
Mounting Bracket
Safety Cable
(such as CH-05 from Chauvet)
LED Pinspot 3 QRG Rev. 3
2
QUICK REFERENCE GUIDE
EN

IRC-6 (Infrared Remote Control)

The LED Pinspot 3 can be operated with the CHAUVET DJ IRC-6 (sold separately).
BUTTON FUNCTION
Turns LED on/off
Increases LED output (10 levels)
Decreases LED output (10 levels)

Technical Specifications

Dimensions and Weight
LENGTH WIDTH HEIGHT WEIGHT
4.6 in (116.5 mm) 4.1 in (104 mm) 2.7 in (68 mm) 1 lb (0.5 kg)
Note: Dimensions in inches rounded to the nearest decimal digit. Power
POWER SUPPLY TYPE RANGE VOLTAGE SELECTION
Switching (internal) 100–240 VAC, 50/60 Hz Auto-Ranging
PARAMETER 120 V, 60 HZ 230 V, 50 HZ
Consumption 8 W 8 W
Operating current 0.1 A 0.05 A
POWER I/O US/CANADA UK/WORLDWIDE
Fixed Power Cord Edison (US) Local Plug
Light Source
TYPE POWER LIFESPAN
LED 5 W 50,000 hours
COLOR QUANTITY CURRENT
Cool White 1 1.6 A
Photometrics
PARAMETER
Beam Angle
Illuminance @ 2 m 3,558 lux
Thermal
MAXIMUM EXTERNAL TEMP. COOLING
104 °F (40 °C) Convection
Ordering
PRODUCT ITEM CODE UPC NUMBER
LED Pinspot 3 03051229 781462215774
3
LED Pinspot 3 QRG Rev. 3
GUÍA DE REFERENCIA RÁPIDA

Acerca de esta guía

La Guía de referencia rápida (GRR) del LED Pinspot 3 USB contiene información básica sobre el producto, como montaje y especificaciones técnicas.

Exención de responsabilidad

La información y especificaciones contenidas en esta GRR están sujetas a cambio sin previo aviso.

Notas de seguridad

Estas notas de seguridad incluyen información importante sobre el montaje, uso y mantenimiento.
Conecte este producto SOLO a un circuito con toma de tierra y protegido.
NO mire a la fuente de luz cuando el producto esté encendido.
Asegúrese de que el cable de alimentación no está retorcido ni estropeado.
Nunca desconecte este producto de la alimentación tirando del cable.
!
Cuando monte este producto en alto, use un cable de seguridad.
NO permita la presencia de materiales inflamables cerca de la unidad cuando esté en funcionamiento.
NO toque este producto cuando esté en funcionamiento, pues podría estar caliente.
La tensión del enchufe al que conecte este producto ha de estar en el rango establecido en el grabado o en el panel posterior del producto.
¡Este producto es para uso en interiores solamente! (IP20) Para evitar riesgos de incendio o descarga, no exponga este producto a la lluvia o la humedad.
Monte siempre este producto en una ubicación con ventilación adecuada, al menos a 20 in (50 cm) de superficies adyacentes.
Asegúrese de que ninguna ranura de ventilación en la carcasa de la unidad queda bloqueada.
Nunca conecte este producto a un atenuador o reostato.
Use SOLAMENTE los soportes de colgar/montar o las asas para mover este producto.
La temperatura ambiente máxima es de 104 °F (40 °C). No haga funcionar este producto a temperaturas más altas.
En caso de un problema grave de funcionamiento, deje de usarlo inmediatamente.
NO abra este producto. No contiene piezas reparables por el usuario.
Para evitar un desgaste innecesario y alargar su vida útil, desconecte completamente el producto mediante el interruptor o desenchufándolo durante periodos en que no se use.
ES

Contacto

Fuera de EE. UU., Reino Unido, Irlanda, México o Benelux póngase en contacto con su distribuidor para solicitar asistencia o devolver un producto. Visite www.chauvetdj.com para información de contacto.

Qué va incluido

LED Pinspot 3
5-paquetes de geles coloreados
Soporte para colgar con material de montaje
Tarjeta de garantía
Guía de referencia rápida

Para empezar

Desembale su LED Pinspot 3 y asegúrese de que ha recibido todas las partes en buen estado. Si la caja o los componentes parecen dañados, notifíqueselo inmediatamente al transportista, no a Chauvet.
LED Pinspot 3 GRR Rev. 3
4
GUÍA DE REFERENCIA RÁPIDA
ES

Descripción del producto

El LED Pinspot 3 es un foco de luz compacto, que cabe en la palma de la mano, con una atenuación fácilmente controlable gracias al mando a distancia IRC-6 opcional. Cambie de color con el paquete de 5 geles incluido.

Visión general del producto

Sensor IR
Lente
Clip de gel
Cable de
alimentación

Dimensiones

4,6 in
116,5 mm
2,7 in
68 mm
4,1 in
104 mm

Corriente alterna

Este producto tiene una fuente de alimentación con detección automática que puede funcionar con un rango de tensión de entrada de 100–240 VCA, 50/60 Hz.
Para evitar un desgaste innecesario y alargar su vida útil, desconecte completamente el producto
!
mediante el interruptor o desenchufándolo durante periodos en que no se use.

Montaje

Antes de montar este producto, lea las Notas de seguridad.

Diagrama de montaje

Abrazadera
(como la CLP-15N de Chauvet)
Soporte de montaje
5
Cable de seguridad
(como el CH-05 de Chauvet)
LED Pinspot 3 GRR Rev. 3
GUÍA DE REFERENCIA RÁPIDA
ES

IRC-6 (control remoto por infrarrojos)

El LED Pinspot 3 es totalmente compatible con el control remoto por infrarrojos (IRC-6) de CHAUVET DJ. (Se vende por separado).
BOTÓN FUNCIÓN
Apaga/enciende el LED
Aumenta la emisión del LED (10 niveles)
Disminuye la emisión del LED (10 niveles)

Especificaciones Técnicas

Dimensiones y Peso
LONGITUD ANCHURA ALTURA PESO
4,6 in (116,5 mm) 4,1 in (104 mm) 2,7 in (68 mm) 1 lb (0,5 kg)
Nota: Las dimensiones en pulgadas están redondeadas al dígito decimal más próximo. Alimentación
TIPO DE FUENTE DE ALIMENTACIÓN
Conmutación (interna) 100–240 VCA, 50/60 Hz Detección automática (autorango)
RANGO SELECCIÓN DE TENSIÓN
PARÁMETRO 120 V, 60 HZ 230 V, 50 HZ
Consumo 8 W 8 W
Corriente de funcionamiento 0,1 A 0,05 A
E/S ALIMENT ACIÓN US/CANADÁ UK/MUNDIAL
Cable de alimentación fijo Edison (EE. UU.) Enchufe local
Fuente de luz
TIPO ALIMENTACIÓN DURACIÓN
LED 5 W 50.000 horas
COLOR CANTIDAD INTENSIDAD
Blanco frío 1 1,6 A
Fotometría
PARÁMETRO
Ángulo del haz
Iluminancia a 2 m 3.558 lux
Térmicas
TEMP. EXTERNA MÁXIMA REFRIGERACIÓN
104 °F (40 °C) Convección
Pedidos
NOMBRE DE PRODUCTO CÓDIGO DE ARTÍCULO NÚMERO UPC
LED Pinspot 3 03051229 781462215774
LED Pinspot 3 GRR Rev. 3
6
MANUEL DE RÉFÉRENCE
FR

A propos de ce manuel

Le Manuel de Référence (MR) du LED Pinspot 3 reprend des informations de base sur cet appareil notamment en matière de montage et spécifications techniques.

Clause de non Responsabilité

Les informations et caractéristiques contenues dans ce MR sont sujettes à modification sans préavis.

Consignes de Sécurité

Ces consignes de sécurité contiennent des informations importantes en matière d'installation, d'utilisation et d'entretien.
Cet appareil DOIT être relié à un circuit mis à la terre et protégé.
NE PAS exposer directement les yeux à la source de lumière lorsque le produit est allumé.
Veillez à ce que le cordon d'alimentation ne soit jamais pincé ou endommagé.
Ne débranchez jamais cet appareil en tirant sur le cordon d'alimentation.
!
En cas de montage de l'appareil en hauteur, veillez à toujours utiliser un câble de sécurité.
NE PAS laisser de produit inflammable à proximité de l'appareil lorsque celui-ci fonctionne.
NE PAS toucher au boîtier de l'appareil lorsqu'il est en fonctionnement, celui-ci pouvant être très chaud.
La tension de la source d'énergie à laquelle est connecté cet appareil doit être dans la plage indiquée sur l'étiquette ou sur le panneau arrière de l'appareil.
Cet appareil doit uniquement être utilisé en intérieur ! (IP20) Afin d'éviter tout risque d'incendie ou de décharge électrique, veillez à n'exposer cet appareil ni à la pluie ni à l'humidité.
Installez toujours cet appareil dans un endroit bien ventilé à au moins 50 cm (20 po) des surfaces adjacentes.
Assurez-vous qu'aucune fente de ventilation de l'appareil n'est obstruée.
Ne connectez jamais cet appareil à un variateur ou un rhéostat.
Utilisez EXCLUSIVEMENT le support de suspension/fixation pour soulever cet appareil.
La température ambiante maximale est de 40 °C (104 °F). Ne faites pas fonctionner cet appareil à des températures plus élevées.
En cas de sérieux problèmes de fonctionnement, arrêtez l'appareil immédiatement.
NE PAS ouvrir cet appareil. Il ne contient aucune pièce réparable par l'utilisateur.
Durant les périodes de non-utilisation, pour éviter tout usure inutile et pour prolonger la durée de vie, éteignez complètement l'appareil en le débranchant ou en coupant le disjoncteur.

Nous contacter

En dehors des États-Unis, du Royaume-Uni, de l'Irlande, du Mexique ou du Benelux, contactez votre fournisseur si vous avez besoin d'assistance ou pour retourner un appareil. Veuillez consulter le site internet www.chauvetdj.com pour obtenir des informations pour nous contacter.

Contenu

LED Pinspot 3
Pack de 5 gels colorés
Fixation de suspension avec matériel de montage
Fiche de garantie
Manuel de référence

Préalable

Déballez votre LED Pinspot 3 et assurez-vous que vous avez reçu toutes les pièces en bon état. Si la boîte et/ou son contenu semble endommagés, contactez immédiatement le transporteur, et non pas Chauvet.
7
LED Pinspot 3 MR Rév. 3
MANUEL DE RÉFÉRENCE

Description de l'appareil

Le LED Pinspot 3 est un projecteur compact tenant dans la paume de la main et qui permet un contrôle aisé de la gradation avec la télécommande IRC-6 en option. Modifiez la couleur avec le pack de 5 gels inclus.

Vue d'ensemble du produit

Cordon
Capteur IR
Lentille

Dimensions

Attache pour gel
4,6 po
116,5 mm
d'alimentation
FR
2,7 po
68 mm
4,1 po
104 mm

Alimentation CA

Cet appareil est doté d'une alimentation universelle qui peut prendre en charge toute tension d'entrée comprise entre 100 et 240 VCA, 50/60 Hz.
Durant les périodes de non-utilisation, pour éviter toute usure inutile et pour prolonger la durée
!
de vie, éteignez complètement l'appareil en le débranchant ou en coupant le disjoncteur.

Montage

Avant de monter cet appareil, veuillez lire les Consignes de Sécurité.

Schéma de montage

(par exemple modèle CLP-15N
Support de montage
Pince
de Chauvet)
Câble de sécurité
(par exemple modèle CH-05 de
Chauvet)
LED Pinspot 3 MR Rév. 3
8
MANUEL DE RÉFÉRENCE
FR

IRC-6 (Télécommande par infrarouge)

Le LED Pinspot 3 est compatible avec la télécommande infra-rouge (IRC-6) de CHAUVET DJ (Vendu séparément).
BOUTON

Spécifications techniques

Dimensions et Poids
Remarque: Les dimensions en pouce sont arrondies à la décimale la plus proche. Alimentation
FONCTION
Activer ou désactiver les LEDs
Augmenter le niveau de sortie des LED (10 niveaux)
Diminuer le niveau de sortie des LED (10 niveaux)
LONGUEUR LARGEUR HAUTEUR POIDS
116,5 mm (4,6 po) 104 mm (4,1 po) 68 mm (2,7 po) 0,5 kg (1 lb)
TYPE D'ALIMENTATION PLAGE SÉLECTION DE TENSION
Commutation (interne) 100–240 VCA, 50/60 Hz Universelle
PARAMÈTRE 120 V, 60 HZ 230 V, 50 HZ
Consommation 8 W 8 W
Courant de fonctionnement 0,1 A 0,05 A
E/S ALIMENT ATION US/CANADA UK/MONDE EUROPE
Cordon d'alimentation fixe Edison (US) Prise locale
Source lumineuse
TYPE ALIMENTATION DURÉE DE VIE
LED 5 W 50 000 heures
COULEUR QUANTITÉ COURANT
Blanc froid 1 1,6 A
Photométrie
PARAMÈTRE
Angle de faisceau
Éclairement @ 2 m 3 558 lux
Thermique
TEMPÉRATURE EXTERNE MAXIMUM
40 °C (104 °F) Convection
Commande
NOM DU PRODUIT CODE DE L'ARTICLE CODE UPC
LED Pinspot 3 03051229 781462215774
SYSTÈME DE REFROIDISSEMENT
9
LED Pinspot 3 MR Rév. 3
SCHNELLANLEITUNG
DE

Über diese Schnellanleitung

In der Schnellanleitung des LED Pinspot 3 finden Sie die wesentlichen Produktinformationen, wie etwa über die Montage und technische daten.

Haftungsausschluss

Die in dieser Anleitung aufgeführten Informationen und Spezifikationen können ohne vorherige Ankündigung geändert werden.

Sicherheitshinweise

Diese Sicherheitshinweise enthalten wichtige Informationen über die Montage, Verwendung und Wartung des Geräts.
Schließen Sie dieses Produkt NUR an einen mit der Erde verbundenen und geschützten Stromkreis an.
NIEMALS in die Lichtquelle schauen, während das Gerät eingeschaltet ist.
Stellen Sie sicher, dass das Netzkabel nicht gequetscht oder beschädigt ist.
!
Ziehen Sie beim Trennen des Geräts von der Stromversorgung nie am Kabel.
Bei Montage über Kopf immer ein Sicherungsseil verwenden.
KEINE entflammbaren Materialien während des Betriebs in der Nähe des Geräts lagern.
NIEMALS während des Betriebs das Gehäuse berühren, da dies sehr heiß wird.
Die Spannung der Schukosteckdose, an die Sie das Gerät anschließen, muss sich innerhalb des Spannungsbereiches befinden, der auf dem Hinweisschild oder dem rückwärtigen Bedienfeld des Geräts angegeben ist.
Dieses Gerät darf nur im Innenbereich verwendet werden. (IP20) Um das Risiko von Bränden oder elektrischen Schlägen zu vermeiden, dürfen Sie das Gerät nicht Regen oder Feuchtigkeit aussetzen.
Installieren Sie das Gerät an einem Ort mit ausreichender Belüftung und mit einem Abstand von 50 cm zu den angrenzenden Flächen.
Stellen Sie sicher, dass die Lüftungsöffnungen im Gehäuse des Geräts nicht verschlossen sind.
Schließen Sie dieses Gerät niemals an einen Dimmer oder Regelwiderstand an.
Das Gerät NUR an den Hänge-/Befestigungsbügeln oder Griffen tragen.
Die maximal zulässige Umgebungstemperatur beträgt 40 °C. Nehmen Sie das Gerät nicht bei höheren Temperaturen in Betrieb.
Bei ernsthaften Betriebsproblemen stoppen Sie umgehend die Verwendung des Geräts.
Dieses Gerät NICHT öffnen. Die eingebauten Komponenten sind für den Kunden wartungsfrei.
Um unnötigen Verschleiß zu vermeiden und die Lebensdauer des Geräts zu verlängern, trennen Sie während längerer Perioden des Nichtgebrauchs das Gerät vom Stromnetz – entweder per Trennschalter oder durch Herausziehen des Steckers aus der Steckdose.

Kontakt

Kunden außerhalb der USA, GB, Irland, Mexiko oder Benelux wenden sich an ihren Lieferanten, um den Kundensupport in Anspruch zu nehmen oder ein Produkt zurückzuschicken. Kontaktinformationen finden Sie unter www.chauvetdj.com.

Packungsinhalt

LED Pinspot 3
Ein Set mit 5 eingefärbten Gels
Hängebügel mit Befestigungsmaterial
Garantiekarte
Schnellanleitung

Start

Packen Sie Ihren LED Pinspot 3 aus und überprüfen Sie, ob Sie alle Teile unbeschädigt erhalten haben. Wenn die Verpackung beschädigt ist, benachrichtigen Sie umgehend das Transportunternehmen, nicht jedoch Chauvet.
LED Pinspot 3 SAL Rev. 3
10
SCHNELLANLEITUNG
DE

Produktbeschreibung

Der LED Pinspot 3 ist ein kompakter, handtellergroßer Punktleuchter, der mit der optionalen Fernbedienung IRC-6 eine einfache Steuerung der Dimmung bietet. Farbänderung mit dem beiliegenden Set mit 5 eingefärbten Gels.

Produktübersicht

IR-Sensor Netzkabel
Linse
Gel-Clip

Abmessungen

4,6 in
116,5 mm
2,7 in
68 mm
4,1 in
104 mm

Wechselstrom

Dieses Gerät verfügt über ein Vorschaltgerät, das automatisch die anliegende Spannung erkennt, sobald der Netzstecker in die Schukosteckdose gesteckt wird, und kann mit einer Eingangsspannung von 100~240 V AC, 50/60 Hz arbeiten.
Um unnötigen Verschleiß zu vermeiden und die Lebensdauer des Geräts zu verlängern, trennen
!
Sie während längerer Perioden des Nichtgebrauchs das Gerät vom Stromnetz – entweder per Trennschalter oder durch Herausziehen des Steckers aus der Steckdose.

Montage

Lesen Sie vor der Montage dieses Geräts in jedem Fall die Sicherheitshinweise.

Montageansicht

(wie die CLP-15N von Chauvet)
11
Klemmen-
Befestigungsbügel
Sicherheitskabel
(wie die CH-05 von Chauvet)
LED Pinspot 3 SAL Rev. 3
SCHNELLANLEITUNG

IRC-6 (Infrarot-Fernbedienung)

Der LED Pinspot 3 ist vollständig kompatibel mit der Infrarot-Fernbedienung (IRC-6) von CHAUVET DJ (Separat erhältlich).
TASTE FUNKTION
Schaltet LEDs ein/aus
Erhöht die LED-Ausgabe (10 Stufen)
Verringert die LED-Ausgabe (10 Stufen)

Technische Daten

Abmessungen und Gewicht
LÄNGE BREITE HÖHE GEWICHT
4,6 in (116.5 mm) 4,1 in (104 mm) 2,7 in (68 mm) 1 lb (0,5 kg)
Hinweis: Abmessungen in Zoll sind auf die nächste Dezimalstelle gerundet. Leistungsaufnahme
NETZTEILTYP BEREICH SPANNUNGSSCHALTER
Schaltend 100–240 V, 50/60 Hz Autom. Spann.-Erkennung
DE
PARAMETER 120 V, 60 HZ 230 V, 50 HZ
Stromverbrauch 8 W 8 W
Betriebsstromstärke 0,1 A 0,05 A
I/O-EINGANGSBUCHSE USA/KANADA GB/WELTWEIT
Angeklemmtes Netzkabel Edison (USA) Lokaler Stecker
Leuchtquelle
TYP LEISTUNGSAUFNAHME DAUER
LED 5 W 50.000 Stunden
FARBE MENGE STROM
Kaltweiß 1 1,6 A
Lichttechnik
PARAMETER
Abstrahlwinkel
Beleuchtungsstärke bei 2 m 3.558 lux
Wärmeentwicklung
MAX. EXTERNE TEMP. KÜHLUNG
104 °F (40 °C) Konvektion
Bestellung
PRODUKTBEZEICHNUNG ARTIKELCODE UPC-NUMMER
LED Pinspot 3 03051229 781462215774
LED Pinspot 3 SAL Rev. 3
12
GUIDA RAPIDA
IT

Informazioni sulla Guida

La Guida Rapida di LED Pinspot 3 contiene informazioni di base sul prodotto quali montaggio e Specifiche Tecniche.

Esclusione di responsabilità

Le informazioni e le specifiche contenute in questa guida possono essere modificate senza preavviso.

Note di Sicurezza

Le Note di Sicurezza includono informazioni importanti circa il montaggio, l'uso e la manutenzione.
Collegare questa unità SOLTANTO ad un circuito dotato di messa a terra e protetto.
NON guardare la sorgente luminosa quando l'unità è in funzione.
Assicurarsi che il cavo di alimentazione non sia piegato o danneggiato.
!
Non scollegare mai questa apparecchiatura dall'alimentazione elettrica tirando il cavo.
Per il montaggio in alto dell'unità utilizzare SEMPRE un cavo di sicurezza.
NON collocare materiale infiammabile vicino all'unità mentre è in funzione.
NON toccare l'unità durante il funzionamento perché potrebbe essere molto calda.
La tensione della presa a muro cui si collega l'apparecchiatura deve trovarsi entro il campo specificato sull'etichetta o sul pannello posteriore.
Questa apparecchiatura deve essere utilizzata soltanto in interni (IP20)! Per evitare il rischio di incendio o di folgorazione non esporre l'apparecchiatura alla pioggia o all'umidità.
Montare sempre l'unità in posizione ben ventilata, ad almeno 50 cm. (20") da qualsiasi superficie.
Assicurarsi che nessuna apertura di ventilazione dell'unità sia ostruita.
Non collegare mai ad un dimmer o ad un reostato.
Prendere e trasportare l'unità SOLTANTO dalla staffa per il montaggio sospeso o dalle maniglie.
Massima temperatura ambiente ammessa: 40 °C (104 °F). Non utilizzare l'unità a temperature superiori.
In caso di gravi problemi di funzionamento sospendere immediatamente l'utilizzo.
NON aprire l'unità. Non contiene parti riparabili dall'utente.
Per evitare un consumo inutile ed aumentare la durata, durante i periodi di non utilizzo disconnettere completamente il prodotto dall'alimentazione con l'interruttore o scollegando il cavo.

Contatti

Per richiedere assistenza o restituire l'apparecchiatura, al di fuori di Stati Uniti, Regno Unito, Irlanda, Messico o Benelux contattare il distributore locale. Per informazioni sui contatti, visitare il sito Web www.chauvetdj.com.

Che cosa è incluso

LED Pinspot 3
Confezione da 5 gelatine colorate
Staffa per montaggio sospeso con relativi accessori
Scheda di garanzia
Guida Rapida

Per iniziare

Disimballare LED Pinspot 3 ed accertarsi di aver ricevuto tutti i componenti integri. Se l'imballo appare danneggiato, farlo immediatamente presente al trasportatore e non a Chauvet.
13
LED Pinspot 3 GR Rev. 3
GUIDA RAPIDA

Descrizione del prodotto

Pinspot LED 3 è un faretto compatto e portatile che consente un facile controllo dell'attenuazione con il telecomando opzionale IRC-6. Possibilità di cambiare il colore grazie alle gelatine incluse (confezione da 5).

Informazioni generali

IT
Sensore IR
Lente
Clip fissaggio
gelatina
Cavo di
alimentazione

Dimensioni

4,6 po
116,5 mm
2,7 po
68 mm
4,1 po
104 mm

Alimentazione CA

Questa unità è dotata di alimentatore a commutazione automatica con tensione in ingresso di 100–240 V CA, 50/60 Hz.
Per evitarne l'eccessiva usura e migliorarne la durata nel tempo, scollegare l'unità dalla presa
!
elettrica o disattivare l'alimentazione tramite l'apposito interruttore, se inutilizzata per lunghi periodi.

Montaggio

Prima di montare l'unità, leggere le Note di Sicurezza.

Schema di montaggio

(come il CLP-15N di Chauvet)
Staffa di montaggio
Morsetto
Cavo di sicurezza
(come il CH-05 di Chauvet)
LED Pinspot 3 GR Rev. 3
14
GUIDA RAPIDA
IT

IRC-6 (Telecomando a infrarossi)

LED Pinspot 3 è totalmente compatibile con il Telecomando a infrarossi (IRC-6) di CHAUVET DJ (Venduto separatamente).
PULSANTE

Specifiche Tecniche

Dimensioni e Peso
4,6 po (116,5 mm) 4,1 po (104 mm) 2,7 po (68 mm) 1 libbre (0,5 kg)
Nota: le dimensioni in pollici sono state arrotondate alla cifra decimale più vicina. Alimentazione
TIPO DI ALIMENTAZIONE ELETTRICA
FUNZIONE
Attiva/disattiva i LED
Aumenta l'intensità di uscita del LED (10 livelli)
Diminuisce l'intensità di uscita del LED (10 livelli)
LUNGHEZZA LARGHEZZA ALTEZZA PESO
RANGE SELEZIONE TENSIONE
Commutazione 100–240 VCA, 50/60 Hz Commutazione automatica
PARAMETRO 120 V, 60 HZ 230 V, 50 HZ
Consumo 8 W 8 W
Corrente di funzionamento 0,1 A 0,05 A
INGRESSO/USCIT A ALIMENTAZIONE
Cavo di alimentazione fisso Edison (US) Spina locale
Sorgente Luminosa
TIPO ALIMENTAZIONE DURAT A NOMINALE
LED 5 W 50000 ore
COLOR QUANTITÀ CORRENTE
Bianco freddo 1 1,6 A
Fotometrici
PARAMETRO
Angolo a fascio
Illuminamento a 2 m 3558 lux
Termico
TEMP. ESTERNA MASSIMA RAFFREDDAMENTO
104 °F (40 °C) Convezione
Ordinazione
NOME PRODOTTO CODICE ARTICOLO NUMERO UPC
LED Pinspot 3 03051229 781462215774
US/CANADA
REGNO UNITO/RESTO DEL MONDO
15
LED Pinspot 3 GR Rev. 3
BEKNOPTE HANDLEIDING

Over deze handleiding

De LED Pinspot 3 Beknopte Handleiding (BH) bevat basisinformatie over het product, zoals montage en technische specificaties.
De informatie en specificaties in deze BH kunnen zonder voorafgaande kennisgeving worden gewijzigd.

Veiligheidsinstructies

Deze veiligheidsinstructies bevatten belangrijke informatie over de installatie, het gebruik en het onderhoud.
Sluit dit product UITSLUITEND op een geaard en beveiligd stroomcircuit.
KIJK NIET in de lichtbron wanneer het apparaat is ingeschakeld.
Zorg ervoor dat het stroomsnoer niet knikt of beschadigd.
!
Koppel dit product nooit los van het stopcontact door aan het snoer te trekken.
Gebruik een veiligheidskabel wanneer het product boven lichaamshoogte wordt gemonteerd.
GEEN brandbare materialen in de buurt van de unit tijdens gebruik.
RAAK het product NIET AAN wanneer het in werking omdat het dan heet zijn.
De spanning van het stopcontact waarop u dit product aansluit moet binnen het vermelde bereik op de sticker of achterkant van het product zijn.
Het product is alleen voor gebruik binnenshuis! (IP20) Om risico op brand of elektrische schokken te voorkomen, mag dit product niet aan regen of vocht worden blootgesteld.
Monteer dit product altijd op een plek met voldoende ventilatie, minstens 20 inch (50 cm) van de aangrenzende oppervlakken.
Zorg ervoor dat er geen ventilatie-openingen van de behuizing van het product worden geblokkeerd.
Sluit dit product nooit aan op een dimmer of een regelweerstand.
Gebruik UITSLUITEND de ophang-/montagebeugel of de hendels om dit product te dragen.
De maximale omgevingstemperatuur bedraagt 40 °C. Gebruik dit product niet bij hogere temperaturen.
Stop in het geval van ernstige operationele problemen onmiddellijk met het gebruik.
Open het product NIET. Het bevat geen te onderhouden onderdelen.
Om onnodige slijtage te elimineren en zijn levensduur te verlengen, gedurende perioden wanneer het product niet wordt gebruikt, moet u het product afsluiten door een aardlekschakelaar om te zetten of door het te ontkoppelen.
NL

Contact

Van buiten de VS, Verenigd Koninkrijk, Ierland, Mexico of Benelux kunt u contact opnemen met de distributeur of om ondersteuning vragen dan wel het product retourneren. Ga naar www.chauvetdj.com voor contactinformatie.

Wat is inbegrepen

LED Pinspot 3
5-pack kleurgels
Opknoping Beugel met montagemateriaal
Garantiekaart
Beknopte handleiding

Om te beginnen

Pak uw LED Pinspot 3 uit en zorg ervoor dat u alle onderdelen in goede staat hebt ontvangen. Als de doos of inhoud beschadigd lijkt, stel dan de vervoerder onmiddellijk op de hoogte, niet Chauvet.
LED Pinspot 3 BH Rev. 3
16
BEKNOPTE HANDLEIDING
NL

Productbeschrijving

De LED Pinspot 3 is een compacte, handformaat spotlight die eenvoudig regelbaar dimmen biedt met de optionele IRC-6 afstandsbediening. Verander de kleur met het meegeleverde 5-pack gels.

Productoverzicht

IR-sensor
Lens
Gelklem
Stroomsnoer

Afmetingen

4,6 in
116,5 mm
2,7 in
68 mm
4,1 in
104 mm

AC-stroom

Dit product heeft een voeding met automatisch bereik die werkt met een ingangsspanning van 100–240 VAC, 50/60 Hz.
Om onnodige slijtage te elimineren en zijn levensduur te verlengen, gedurende perioden wanneer
!
het product niet wordt gebruikt, moet u het product afsluiten door een aardlekschakelaar om te zetten of door het te ontkoppelen.

Montage

Lees alvorens dit product te monteren alle Veiligheidsinstructies.

Montagediagram

(zoals de CLP-15N van Chauvet)
Klem
Montagebeugel
Veiligheidskabel
(zoals de CH-05 van Chauvet)
17
LED Pinspot 3 BH Rev. 3
BEKNOPTE HANDLEIDING

IRC-6 Infrarood Remote Control

De LED Pinspot 3 is compatibel met de IRC-6 infrarood afstandsbediening van CHAUVET DJ (Apart verkocht).
TOETS FUNCTIE
Schakelt LED-lampjes aan/uit
Verhoogt de LED-opbrengst (10 niveaus)
Verlaagt de LED-opbrengst (10 niveaus)

Technische Specificaties

Afmetingen en Gewicht
LENGTE BREEDTE HOOGTE GEWICHT
4,6 in (116,5 mm) 4,1 in (104 mm) 2,7 in (68 mm) 1 lb (0,5 kg)
Let op: Afmetingen in inches, afgerond op de dichtstbijzijnde decimale cijfer. Vermogen
TYPE VOEDING BEREIK VOLTAGE SELECTIE
Schakelend 100–240 V, 50/60 Hz Automatisch wisselend bereik
NL
PARAMETER 120 V, 60 HZ 230 V, 50 HZ
Consumptie 8 W 8 W
Bedrijfsstroom 0,1 A 0,05 A
POWER I/O US/CANADA UK/ WERELDWIJD
Vast stroomsnoer Edison (US) Lokale stekker
Lichtbron
TYPE VERMOGEN GOLFLENGTE
LED 5 W 50.000 uur
KLEUR AANTAL STROOMSTERKTE
Koel wit 1 1,6 A
Lichttechniek
PARAMETER
Stralingshoek
Verlichting @ 2 m 3.558 lux
Thermaal
MAXIMUM EXTERNE. TEMP. KOELING
104 °F (40 °C) Convectie
Bestellen
PRODUCT NAAM ITEM CODE UPC NUMMER
LED Pinspot 3 03051229 781462215774
LED Pinspot 3 BH Rev. 3
18
Multi-Language

Contact Us

EUROPE
MEXICO
Address: Av. de las Partidas 34 - 3B, Zona
QUICK REFERENCE GUIDE
WORLD HEADQUARTERS
General Information Technical Support
Address: 5200 NW 108th Ave. Voice: (844) 393-7575
Sunrise, FL 33351 Fax: (954) 756-8015
Voice: (954) 577-4455 Email:
Fax: (954) 929-5560
Toll Free: (800) 762-1084
General Information Technical Support
Address: Stokstraat 18
9770 Kruishoutem
Belgium
Voice: +32 9 388 93 97
General Information Technical Support
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: +44 (0) 1773 511115
Fax: +44 (0) 1773 511110
General Information Technical Support
Industrial Lerma
Lerma, Edo. de Mexico C.P. 52000
Voice: +52 (728) 285-5000
chauvetcs@chauvetlighting.com
Website
www.chauvetlighting.com
Email: Eutech@chauvetlighting.eu
Website
www.chauvetlighting.eu
Email: uktech@chauvetlighting.com
Website
www.chauvetlighting.co.uk
Email: servicio@chauvet.com.mx
Website
www.chauvet.com.mx
Visit the applicable website above to verify our contact information and instructions to request support. Outside the U.S., United Kingdom, Ireland, Mexico or Benelux, contact the dealer of record..
LED Pinspot 3 QRG Rev. 3 ML6 © Copyright 2016 Chauvet
All rights reserved Printed in the P.R.C.
19
LED Pinspot 3 QRG Rev. 3
Loading...