How it Works
Chauvet DJ
Loading...
E
F
G
H
Loading...
Loading...
Freedom Par Quad-4 IP
Quick Start Guide
80 pgs867.86 Kb1
Users Manual
20 pgs490.63 Kb1
Table of contents
Loading...

Chauvet DJ Freedom Par Quad-4 IP Users Manual

Download
User Manual
TABLE OF CONTENTS
1. Before You Begin .......................................................................................................... 3
Claims ..................................................................................................................................................... 3
2. Introduction ................................................................................................................... 5
3. Setup .............................................................................................................................. 7
Charging the Battery ............................................................................................................................... 7
Battery Life Indicator ............................................................................................................................... 7
Battery Run Time .................................................................................................................................... 7
Orientation .............................................................................................................................................. 8
Rigging ................................................................................................................................................... 8
4. Operation ....................................................................................................................... 9
Starting Address ................................................................................................................................... 10
Master/Slave Mode ............................................................................................................................... 10
DMX Personalities ................................................................................................................................ 10
10CH .................................................................................................................................................... 13
6-CH ..................................................................................................................................................... 14
4-CH ..................................................................................................................................................... 14
Auto Mode ............................................................................................................................................ 15
Program Speed..................................................................................................................................... 15
Selecting the Dimmer Mode ................................................................................................................. 15
Static Colors ......................................................................................................................................... 15
Custom Color Mixing ............................................................................................................................ 15
IRC-6 Operation.................................................................................................................................... 16
5. Maintenance .................................................................................................................17
6. Technical Specifications ..............................................................................................18
Returns .............................................................................................................................19
Contact Us .........................................................................................................................20
Page 2 of 20 Freedom Par Quad-4 IP User Manual Rev. 3
What Is
Included
• Freedom Par Quad-4 IP IRC-6 Remote Control
• Warranty Card
Unpacking
Instructions
Carefully unpack the product immediately and check the container to make sure all the
If the box or the contents (the product and included accessories) appear damaged from
Text
Convention
Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Critical installation, configuration, or operation information. Not damage to the product, or cause harm to the operator.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects.
any and all liability to any party for any loss, damage or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident or any other
of this document without any
obligation to notify any person or company of such revision, however, Chauvet has no
are registered
company and product names and logos

1. BEFORE YOU BEGIN

Claims
Conventions
• Power Cord
•
parts are in the package and are in good condition.
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier immediately may inv alidat e y our claim. In addition, keep the box and contents for inspection. For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with Chauvet within 7 days of delivery.
Symbol Meaning
Electrical warning. Not following these instructions may cause electrical damage to the product, accessories, or the user.
following these instructions may make the product not work, cause
• Quick Reference Guide
Important installation or configuration information. The product may not function correctly if this information is not used.
Useful information.
However, Chauvet assumes no responsibility and specifically disclaims
cause. Chauvet reserves the right to revise the content obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetlighting.com. The works of authorship contained in this manual, including, but not limited to, all design,
text and images are owned by Chauvet.
© Copyright 2017 Chauvet & Sons, Inc. All rights reserved.
Electronically published by Chauvet in the United States of America. CHAUVET, the Chauvet logo, Freedom Par Quad-4 IP, D-Fi, and TRUSST
trademarks or trademarks of Chauvet & Sons Inc. (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other referred to herein may be trademarks of their respectiv e co mp anies.
Freedom Par Quad-4 IP User Manual Rev. 3 Page 3 of 20
Product at a
x
P
P
P
x
P
P
x
P
Safety Notes
Do not touch the product’s housing when operating because it may be very hot.
completely disconnect the product from power via breaker or by unplugging it.
Glance
Use on Dimmer Outdoor Use Sound-Active DMX Master/Slave
Please read the following Safety Notes carefully before working with the product. The Notes include important safety information about instal lation, usage, and maintenance.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing
the fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power by pulling or tugging on the cord.
• If mounting the product overhead, always secure to a fastening device using a
safety cable.
• Make sure there are no flammable materials close to the product when operating.
•
• Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
• This product is for indoor or temporary outdoor use (IP54). Do not expose to harsh or excessively corrosive environmental conditions (whether indoors or outdoors), including, but not limited to, extreme temperatures, humidity, atmospheric conditions (including salinity or pressure), radiation (UV, infrared or nuclear), shock and conditions which exceed the product’s Ingress Protection (“IP”) rating.
• Do not submerge this product. This product may be exposed to rain and moisture.
• Always install the product in a location with adequate ventilation, at least
20 in (50 cm) from adjacent surface s.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Never connect the product to a dimmer or a rheostat.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord.
• The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
• This product is not intended for permanent installation.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
Auto Programs Auto-ranging Power Supply Replaceable Fuse User-Serviceable
Keep this User Manual for future use. If you sell the product, be sure that they receive this document.
Page 4 of 20 Freedom Par Quad-4 IP User Manual Rev. 3

2. INTRODUCTION

Product Overview

On/Off Switch
Display
Menu
Buttons
Power In
Carry Handle
Weather
Resistant
Cover
Infrared Sensor
Glare Shield
D-Fi™ AUTO
Sync/Clear Button
Fuse Holder
Kickstand
Freedom Par Quad-4 IP User Manual Rev. 3 Page 5 of 20
The Weather Resistant Cover must be CLOSED in order for the product to be IP rated.

Product Dimensions

5.4 in
138 mm
5.7 in
145 mm
7.5 in
191 mm
Page 6 of 20 Freedom Par Quad-4 IP User Manual Rev. 3
AC Power
The Freedom Par Quad-4 IP has an internal auto-ranging power supply and it can work with an input voltage range of 100 to 240 VAC , 50/60 H z .
• Always connect the product to a protected circuit (circuit breaker or fuse).
has an appropriate electrical ground to avoid the risk
To eliminate unnecessary wear and improve its lifespan, during periods of
via breaker or by
unplugging it.
to a rheostat (variable resistor) or dimmer circuit, even if
Fuse
1. Disconnect the product from power .
6. Insert the fuse holder back in place and reconnect power.
Battery Power
The Freedom Par Quad-4 IP comes with a rechargeable lithium battery for cable-free operation.
Charging the
Battery
The battery charges whenever the product is plugged into a power source. If the product
Battery Life
Indicator
The indicators on the LED Menu Display show how much battery life remains available.
100%
75%
50%
25%
Maximum Run Time
(all colors on)
Maximum Run Time
(single color on)
Up to 8 hours
Up to 20 hours
7 hours
Installed fuse (held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

3. SETUP

Replacement
Make sure the product of electrocution or fire.
•
non-use completely disconnect the product from power
Never connect the product the rheostat or dimmer channel serves o nly as a 0 t o 100% switch.
2. Wedge the tip of a flat-head screw driver into t he slot of the fus e holder .
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
Disconnect the product from the power outlet before replacing the fuse.
Always replace a blown fuse with another of the same type and rating.
A spare fuse is not included; however, t he safety cap has room for a spare.
is plugged in and not in operation, make sure the On/Off switch is in the Off position.
The drawing below provides a key to reading the battery life indicators
For optimal battery life, charge the Freedom Par Quad-4 IP battery for 24 hours prior to initial use.
Battery Run Time
Freedom Par Quad-4 IP User Manual Rev. 3 Page 7 of 20
Recharge Time
Mounting
, read and follow the safety recommendations indicated in the
The Freedom Par Quad-4 IP has a compact design to fit perfectly inside the TRUSST
50 mm truss without the need for a bracket, using an M12
nd. The
place the product so there is at least
20” of space around it and it is accessible for progra mming an d contr ol panel operation.
Rig the product from a structure or surface that can support the product’s weight. See
This product is for indoor or temporary outdoor use (IP54). Do not expose to harsh or excessively corrosive environmental conditions (whether indoors or outdoors), including,
extreme temperatures, humidity, atmospheric conditions (including salinity or pressure), radiation (UV, infrared or nuclear), shock and conditions which exceed the product’s Ingress Protection (“IP”) rating.
clamp
Threaded Mounting
Before mounting the product
Safety Notes.
Orientation
truss systems. It attaches to 35­threaded rigging point. Floor mounting is a cinch with a built-in adjustable kicksta product may be mounted in any position; however,
Rigging
Technical Specifications in this manual for the product’s weight.
When mounting the product overhead, always use a mounting clamp and safety cable. Mount the product securely to a rigging point, such as a pipe or truss. When rigging the product onto a truss, you should use a mounting clamp of appropriate weight capacity. The Freedom Par Quad-4 IP has an M12 threaded mounting hole, which is appropriate for this purpose. For the Chauvet line of mounting clamps, go to
https://www.chauvetdj.com/products/category/accessories/.
When mounting the product on the floor, make sure that the product and any cables are away from people and vehicles.
but not limited to,
Mounting Diagram
Hole
Size M12
Mounting Clamp
(such as the CLP-15
from Chauvet)
Safety Cable
(such as CH-05 from
Chauvet)
Page 8 of 20 Freedom Par Quad-4 IP User Manual Rev. 3
Control Panel
Operation
Button
Function
<ENTER>
Menu Map
Main Function
Programming Levels
Description
4-CH
6-CH
10CH
Static Colors
C--
C 1–C 15
Selects 1 of 15 static colors
Auto Programs
P--
P 1–P 4
Selects 1 of 4 auto program
Program Speed
S--
S 1–S100
Sets auto program speed (slow to fast)
r 0–r255
Red (0–100%)
g 0–g255
Green (0–100%)
b 0–b255
Blue (0–100%)
A 0–A255
Amber (0–100%)
OFF
dIM1
dIM2
dIM3
On
Off
Automatically select DMX receive frequency
drCH
dr 1–dr16
Manually select DMX receive frequency
Automatically select DMX transmit frequency
dtCH
dt 1–dt16
Manually select DMX transmit frequency

4. OPERATION

To access the control panel functions, use the four buttons located underneath the display. Please refer to the Product Overview to see the button locations on the control panel.
<MENU> Selects an operation mode
<UP> Scrolls up the list of options or selects a higher value
<DOWN> Scrolls down the list of options or selects a lower value
Activates a menu option or a selected value
DMX Perso n ality
and Starting
Address
Custom Color
Mixing
Dimmer DiM
Infrared SET
2.4 GHz D-Fi S-tr
U--
d 1–d512
drAS drAU
dtAS dtAU
Selects DMX personality and DMX starting value
Sets the dimming curve: dIM1 (fast) to dIM3 (slow), or OFF
Turns infrared on or off
Freedom Par Quad-4 IP User Manual Rev. 3 Page 9 of 20
Wireless DMX
The Freedom Par Quad-4 IP operates by itself in Standalone mode.
website http://www.chauvetdj.com/wp-content/uploads/.
To ensure full access to all channels in each DMX mode, the highest recommended DMX address is 503.
Master/Slave
Master/Slave mode allows a single Freedom Par Quad-4 IP (the master) to wirelessly
) the slaves are
9. Set the master to run in auto program, stati c color, or c ustom c olor mixing mode.
DMX
When selecting a starting DMX address, always consider the number of DMX channels
channel mode) or
Linking
Starting Address
It also operates in Master/Slave mode, or in Wireless DMX mode, both of which require wireless DMX linking. In Master/Slave mode the master product sends wireless DMX signals to the slaves. In Wireless DMX mode a lighting control board or D-Fi product must send wireless DMX signals to the products. To DMX-link a number of Freedom Par Quad-4 IP using wireless D-Fi, see D-Fi 2.4 GHz
(DMX Mode Manual Sync).
Information about DMX is in the DMX Primer, which is available from the Chauvet
Mode
control the actions of one or more Freedom products (the slaves) without a DMX controller. The master will be set to operate in either an auto program, static color, or custom color mixing mode, while the slaves will be set to operate in wireless DMX receiver mode. Once set, the slaves will operate in unison with the master. Configure the units as indicated below.
Slaves:
1. Press <MENU> repeatedly until any DMX per sonality shows on the display .
2. Press <ENTER>.
3. Set the DMX address to d 1.
4. Press <MENU> repeatedly until S-tr shows on the display.
5. Use <UP> and <DOWN> to select drCH.
6. Press <ENTER>.
7. Use <UP> and <DOWN> to select a receiving channel dr 1–dr16.
8. Press <ENTER>.
9. Finish setting all the slaves. Note: All slaves must be set to the same DMX personality and D-Fi channel.
Master:
1. Press <MENU> until the DMX personality the slaves are s et t o shows on the display.
2. Press <ENTER>.
3. Set the DMX address to d 1.
4. Press <MENU> repeatedly until S-tr shows on the display.
5. Use <UP> and <DOWN> to select dtCH.
6. Press <ENTER>.
7. Use <UP> and <DOWN> to select the transmitting channel (dt 1–dt16 set to.
8. Press <ENTER>.
Never transmit a DMX signal from a controller ov er a D-Fi channel being used for Master/Slave.
Personalities
the selected DMX mode uses. If you choose a starting address that is too high, you could restrict the access to some of the product’s channels. If unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com. To select the DMX personality and starting address, do the following:
1. Press <MENU> repeatedly until 3-CH (3-channel mode), 6-CH (6- 10CH (10-channe l mode) show s on t he disp lay.
2. Press <ENTER> and d 1–d512 sh ows on the display.
3. Use <UP> or <DOWN> to select the starting addr ess.
4. Press <ENTER>.
Page 10 of 20 Freedom Par Quad-4 IP User Manual Rev. 3
D-Fi 2.4 GHz
(DMX Mode
The Freedom Par Quad-4 IP series offers wireless control of 2 or more products with a
). The channel number should match the transmitting signal you chose when setting up the transmitting product.
To sync multiple transmitters in one room, manually set each receiver and the designated transmitter to a specific frequency and then perform the syncing
Fi 2.4 GHz wireless
Fi 2.4
Manual Sync)
single DMX controller. To manually set up the D-Fi 2.4 GHz syncing for DMX, do the following. For the transmitting product:
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until dtCH appears on the display.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to select the transmitting signal (dt 1–dt16).
For the receiving product(s):
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until drCH appears on the display.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to select the receiving signal (dr 1–dr16
steps. Freedom Par Quad-4 IP is fully compatible with the D-
transceiver (transmitter/receiver) from Chauvet (sold separately). For more detailed information about D-Fi 2.4 GHz functionality, refer to the D-
GHz User Manual available at the Chauvet website www.chauvetlighting.com.
Manual syncing is recommended for best results.
Freedom Par Quad-4 IP User Manual Rev. 3 Page 11 of 20
D-Fi 2.4 GHz
The Freedom Par Quad-4 IP offers wireless control of 2 or more products with a single
To configure your product to work with DM X, r efer to t he S tart ing Address section.
• To add additional Freedom products, turn the synced ones off and repeat the above
ts when adding products after initial
If you are experiencing issues or need to improve signal quality, keep the line of sight
• Ensure that all linked products are configured to th e same DM X personality.
Caution: D-Fi 2.4 GHz operation can be interrupte d or inhibit e d by liquid mas ses betw een of sight clear of any liquid mass.
(DMX Mode
Auto Sync)
DMX controller. To automatically set up D-Fi 2.4 GHz syncing for DMX, do the following: For the receiving product(s):
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until drAS appears on the display.
4. Press <ENTER>.
5. The display should show drAU.
For the transmitting product:
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until dtAS appears on the display.
4. Press <ENTER>.
5. The display should show dtAU. Receiving units must be set up before the transmitting unit. Once the steps above are
done, press and hold <AUTO> on just the transmitter for approximately 30 seconds. The display and signal LED will flash to indicate sync is activated. You can then back out to a general menu level and configure the transmitting product to operate it with a DMX controller.
steps with un-synced products. Once all product s are sy nced, t urn them all ba ck on.
• Auto scan syncing must be done within a distance of about 32 ft (10 m).
• Manual syncing is recommended for best resul
system setup.
• between products unobstructed.
the transmitter and receiver such as water , snow , or people. For best results, keep the line
Page 12 of 20 Freedom Par Quad-4 IP User Manual Rev. 3

DMX Channel Assignments and Values

Channel
Function
Value
Percent/Setting
1
Dimmer
2
Red
Green
4
Blue
000ó255
0–100%
5
Amber
000ó010
No function
011ó030
R: 100%
G: 0–100%
B: 0
A: 0
031ó050
R: 100%–0
G: 100%
B: 0
A: 0
051ó070
R: 0
G: 100%
B: 0–100%
A: 0
071ó090
R: 0
G: 100%–0
B: 100%
A: 0
091ó110
R: 0–100%
G: 0
B: 100%
A: 0
111ó130
R: 100%
G: 0
B: 100%–0
A: 0
131ó150
R: 100%
G: 0–100%
B: 0–100%
A: 0
151ó170
R: 100%–0
G: 100%–0
B: 100%
A: 0
171ó200
R: 100%
G: 100%
B: 100%
A: 100%
201ó205
Color temperature 1
206ó210
Color temperature 2
211ó215
Color temperature 3
216ó220
Color temperature 4
221ó225
Color temperature 5
226ó230
Color temperature 6
231ó235
Color temperature 7
236ó240
Color temperature 8
241ó245
Color temperature 9
246ó250
Color temperature 10
251ó255
Color temperature 11
000ó010
No function
011ó255
Strobe, slow to fast
000ó010
No function
011ó060
Auto program 1
061ó120
Auto program 2
121ó180
Auto program 3
181ó255
Auto program 4
Auto Speed
000ó051
Dimmer mode manually set in Menu Options
052ó101
Dimmer mode off
102ó152
Dimmer mode 1, (fast speed)
153ó203
Dimmer mode 2, (medium speed)
10CH
000ó255 0–100% 000ó255 0–100%
3
000ó255 0–100%
000ó255 0–100%
Color Macros and
6
Color Temperature
7
Strobe
8
Auto Programs
9
000ó255 Auto program speed (slow to fast)
10
Freedom Par Quad-4 IP User Manual Rev. 3 Page 13 of 20
Dimmer Mode
204ó255 Dimmer mode 3, (slow speed)
Channel
Function
Value
Percent/Setting
1
Dimmer
2
Red
000ó255
0–100%
Green
4
Blue
000ó255
0–100%
5
Amber
000ó255
No function
000ó255
Strobe, slow to fast
Channel
Function
Value
Percent/Setting
1
Red
000ó255
0–100%
2
Green
3
Blue
Amber
6-CH
000ó255 0–100%
3
6
4-CH
4
000ó255 0–100%
000ó255 0–100%
Strobe
000ó255 0–100% 000ó255 0–100% 000ó255 0–100%
Page 14 of 20 Freedom Par Quad-4 IP User Manual Rev. 3
Configuration
(Standalone)
Auto mode sets the product to 1 of 4 preset color programs.
To set the auto program speed, follow the instructions below:
, sl o w
3. Press <ENTER>.
Selecting the
To select a dimmer mode, do the following:
Press <ENTER>.
To select a preset static color, do the following:
4. Press <ENTER>.
Custom Color
To custom mix a color, follow the instructions below:
6. Repeat steps 3 to 5 until you create your desired color.
Set the product in one of the standalone modes to control without a DMX controller.
• Connect the product to a suitable power outlet.
Auto Mode
Program Speed
Dimmer Mode
Static Colors
To set the product to Auto mode, do the following:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER> and P 1–P 4 shows on the display.
3. Use <UP> or <DOWN> to select the desired auto program:
• P 1 - 3-color snap
• P 2 - 3-color fade
• P 3 - 7-color snap
• P 4 - 7-color fade
4. Press <ENTER>.
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> or <DOWN> to select the desired auto program speed (S 1–S100 to fast).
Press <MENU> repeatedly until dIM shows on the display. Press <ENTER> and one of the following shows on the display:
• OFF (dimmer speed off)
• dIM1 (dimmer mode 1, fast speed)
• dIM2 (dimmer mode 2, middle speed)
• dIM3 (dimmer mode 3, slow speed)
Use <UP> or <DOWN> to select the desired dimmer mode.
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the desired preset color (C 1–C 15).
Mixing
2. Press <ENTER> and one of the following colors shows on the display: r_ _ _ (red), g_ _ _ (green), b_ _ _ (blue), or A_ _ _ (amber).
3. Press <ENTER> repeatedly to select the desired color.
4. Use <UP> or <DOWN> to select the desired color value (0–255).
• NOTE: Selecting 0 will turn the color off.
5. Press <ENTER> to select color value and continue to the next color.
1. Press <MENU> repeatedly until U-- shows on the display.
Freedom Par Quad-4 IP User Manual Rev. 3 Page 15 of 20
IRC-6 Infrared
Remote
Infrared (IR) mode allows the product to be controlled with an infrared remote controller. The
6 from Chauvet. To enable
(turns off the infrared
4. Press <ENTER>.
Be sure the IRC-6 remote is pointing directly at the product and there is nothing in between the remote and the product.
Press <+> or <–> to increase or decrease the output level.
Note: The IRC-6 will not respond to any inputs when the Black Out mode is activated. If the remote does not respond when a button is pressed, try pressing Out mode.
Control
IRC-6 Operation
IRC-6 can remotely set the product to various modes; adjust the color, speed and sensitivity; and set the strobe.
The Freedom Par Quad-4 IP is compatible with the included IRC­use with the IRC-6, follow the instructions below:
1. Press <MENU> repeatedly until SET shows on the display.
2. Press <ENTER> and ON (turns on the infrared sensor) or OFF sensor) shows on the display.
3. Press <UP> or <DOWN> to select the desired option.
Automatic Mode
Automatic mode will enable you to run the automatic programs on the product. To turn on Automatic mode:
1. Press <AUTO> on the IRC-6.
2. Press <+> or <–> to choose between the four different auto programs. To adjust the speed of th e automatic program:
1. Press <SPEED> on the IRC-6.
2. Press <+> or <–> to either increase or decrease the speed of the program.
Manual Color Control
To choose a specific color with the IRC-6:
1. Press <MANUAL> on the IRC-6.
2. Press any number between <0> and <9> to choose your color.
To manually control the RGBA percentage:
1. Press <MANUAL> on the IRC-6.
2. Press <R>, <G>, <B>, or <A> (red, green, blue, or amber) to choose your color. Note: The Freedom Par Quad-4 IP only contains red, green, blue and amber LEDs.
The white, and UV color options on the IRC-6 will only operate with fixtures capable of outputting these color lights.
3. Press <+> or <–> to increase or decrease the percentage of each color.
Miscellaneous Operation
To adjust the strobe rate of the program:
1. Press <STROBE> on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe.
To choose a fade auto program:
• Press <FADE> repeatedly on the IRC-6 to choose between the two auto program fade options
To black out the lights:
• Press <BLACK OUT> on the IRC-6. This will turn off all the lights until the button is pressed again.
To adjust the output level:
1. Press <%> on the IRC-6.
<BLACK OUT>. You may have inadvertently activated the Black
Page 16 of 20 Freedom Par Quad-4 IP User Manual Rev. 3
Product
up reduces light output performance and can cause overheating. This can lead
mechanical wear. To maintain optimum
ice a month.
However, be aware that usage and environmental conditions could be contributing factors

5. MAINTENANCE

Dust build-
Maintenance
to reduction of the light source’s life and/or performance and minimize wear, clean your lighting products at least tw
to increase the cleaning frequency. To clean the product, follow the instructions below:
1. Unplug the product from pow er .
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
6. Softly drag any dirt or grime to the outside of the tra nsp ar ent surfa ce.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully af ter cleaning them.
the external surface/vents.
cleaner, or isopropyl alcohol.
Freedom Par Quad-4 IP User Manual Rev. 3 Page 17 of 20
Dimensions and
Length
Width
Height
Weight
5.4 in (138 mm)
5.7 in (145 mm)
7.5 in (191 mm)
8.0 lb (3.6 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
43 W
40 W
Operating Current
0.6 A
0.3 A
Power linking current (products)
N/A
N/A
Fuse
T 2 A, 250 V
T 2 A, 250 V
Power I/O
U.S./Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
5 W
50,000 hours
Color
Quantity
Current
Quad-color RGBA
4
2 A
Photometrics
Parameter
Value
Field angle
29°
Beam angle
9.5°
Strobe rate
0 to 25 Hz
Illuminance @ 2 m
2,464 lux
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Convection
DMX
I/O Connectors
Channel Range
N/A
4, 6 or 10
Ordering
Product Name
Item Code
UPC Number
Freedom Par Quad-4 IP
03031034
781462213824

6. TECHNICAL SPECIFICATIONS

Weight
Page 18 of 20 Freedom Par Quad-4 IP User Manual Rev. 3
R
In case you need to get support or return a product:
If you are located outside the U.S., UK, Ireland, Mexico, or Benelux, contact your products to them. Visit our website www.chauvetlighting.com for contact details.
Call the corresponding Chauvet Technical Support office and request a Return
returned without an RMA number.
Before sending the product, clearly write the following information on a piece of paper
recommended.
ETURNS
• If you are located in the U.S., contact Chauvet World Headquarters.
• If you are located in the UK or Ireland, contact Chauvet Europe Ltd.
• If you are located in Mexico, contact Chauvet Mexico.
• If you are located in Benelux, contact Chauvet Europe BVBA.
• If you are located in any other country, DO NOT contact Chauvet. Instead, contact
your local distributor. See www.chauvetlighting.com for distributors outside the U.S., UK, Ireland, Mexico, or Benelux.
distributor of record and follow their instructions on how to return Chauvet
Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause for the return. Send the merchandise prepaid, in its original box, and with its original packing and accessories. Chauvet will not issue call tags. Clearly label the package with the RMA number. Chauvet will refuse any product
Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on the box.
and place it inside the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief descriptio n of the prob l em
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are
Chauvet reserves the right to use its own discretion to repair or replace returned product(s).
Freedom Par Quad-4 IP User Manual Rev. 3 Page 19 of 20
C
USA WORLD HEADQUARTERS
General Information
Technical Support
www.chauvetlighting.com
EUROPE
General Information
Technical Support
General Information
Technical Support
MEXICO
General Information
Voice: +52 (728) 690-2010
Technical Support
www.chauvet.com.mx
Visit the applicable website above to verify our contact information and instructions to the dealer of record..
ONTACT
US
Address: 5200 NW 108th Avenue Sunrise, FL 33351 Voice: (954) 577-4455 Fax: (954) 929-5560 Toll free: (800) 762-1084
Address: Stokstraat 18 9770 Kruishoutem Belgium Voice: +32 9 388 93 97
Address: Unit 1C Brookhill Road Industrial Estate Pinxton, Nottingham, UK NG16 6NT Voice: +44 (0)1773 511115 Fax: +44 (0)1773 511110
Address: Av. de las Partidas 34, 3-B Zona Industrial Lerma Lerma, Mexico C.P. 52000
Voice: (844) 393-7575 Fax: (954) 756-8015 Email: tech@chauvetlighting.com
World Wide Web
Email: Eutech@chauvetlighting.eu
World Wide Web
www.chauvetlighting.eu
Email: uktech@chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk
Email: servicio@chauvet.com.mx World Wide Web
request support. Ou tside the U .S., Un ited K ingdom , Irelan d, Mex ico, or Benelux contact
Page 20 of 20 Freedom Par Quad-4 IP User Manual Rev. 3
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use