How it Works
Chauvet DJ
Loading...
Freedom Par Quad-4
Quick Start Guide
41 pgs234.65 Kb0
Users Manual
21 pgs592.78 Kb0
Table of contents
Loading...

Chauvet DJ Freedom Par Quad-4 Users Manual

Download
Page 1
User Manual
Page 2
Freedom™ Par Quad-4 User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin ............................................................................................................................. 3
What Is Included ....................................................................................................................................................................... 3
Unpacking Instructions ............................................................................................................................................................. 3
Text Conventions ...................................................................................................................................................................... 3
Symbols .................................................................................................................................................................................... 3
Disclaimer ................................................................................................................................................................................. 3
Product at a Glance .................................................................................................................................................................. 4
2. Introduction ...................................................................................................................................... 5
Overview ................................................................................................................................................................................... 5
Description ................................................................................................................................................................................ 5
Dimensions ............................................................................................................................................................................... 6
3. Setup ................................................................................................................................................ 7
AC Power ................................................................................................................................................................................. 7
Fuse Replacement.................................................................................................................................................................... 7
Power Linking ........................................................................................................................................................................... 8
Battery Run Time ...................................................................................................................................................................... 8
Mounting ................................................................................................................................................................................... 9
Orientation ................................................................................................................................................................................ 9
Rigging ..................................................................................................................................................................................... 9
4. Operation ........................................................................................................................................ 10
Control Panel Operation ......................................................................................................................................................... 10
DMX Linking ........................................................................................................................................................................... 11
D-Fi™ 2.4 GHz (DMX Mode Manual Sync) ............................................................................................................................ 12
D-Fi™ 2.4 GHz (DMX Mode Auto Sync) ................................................................................................................................ 13
Configuration (Standalone) ..................................................................................................................................................... 16
IRC-6 Operations ............................................................................................................................................................. 17
5. Technical Information .................................................................................................................... 18
Product Maintenance .............................................................................................................................................................. 18
6. Technical Specifications ............................................................................................................... 19
Returns ............................................................................................................................................... 20
Contact Us .......................................................................................................................................... 21
Page 3
1. B
What Is
• Freedom™ Par Quad-4
• Warranty Card
Unpacking
the package, and are in

Claims

If the box, or any of the contents, appear damaged from shipping, save all the packaging and file a claim
all the
For other issues, such as missing components or parts, damage not related to shipping, or concealed
Text
Convention
Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<Enter>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected

Symbols

Symbol
Meaning
Critical installation, configuration, or operation information. Not following these
, or

Disclaimer

The information and specifications contained in this User Manual are subject to change without notice.
assumes no responsibility or liability for any errors or omissions, and reserves the right to revise
be downloaded from
M. Trouard
08/26/2014
A. Leon
09/19/14
EFORE YOU BEGIN
Included
Instructions
Conventions
• Power Cord
• IRC-6 (Infrared Remote Control)
Carefully unpack the Freedom™ Par Quad-4 and check that all the parts are in good condition.
with the carrier immediately. Failure to report damage to the carrier immediately, or failure to save packaging, can invalidate a claim.
damage, file a claim with Chauvet within 7 days of delivery. See Contact Us.
instructions may make the product not work, cause damage to the product cause harm to the operator.
• Quick Reference Guide
Important installation or configuration information. The product may not function correctly if this information is not used.
Useful information.
Chauvet or recreate this manual at any time. The latest version of this manual can
http://www.chauvetlighting.com/product-manuals-literature/.
© Copyright 2014 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
Author Date Editor Date
Freedom™ Par Quad-4 User Manual Rev. 1 Page 3 of 21
Page 4
Product at a
x
P
x
P
P
P
P
x
P

Safety Notes

of this product;
Do not touch the product’s housing when operating because it may be very hot.
disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product to another user, be sure to give this document
Glance
Use on Dimmer Outdoor Use Sound-Activated DMX Master/Slave
These notes include important information about the mounting, usage, and maintenance read before using the product.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing the fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power by pulling or tugging on the cord.
• If mounting the product overhead, always secure to a fastening device using a safety cable.
• Make sure there are no flammable materials close to the product when operating.
•
• Always make sure that the voltage of the outlet to which you are connecting the product is within the
range stated on the decal or rear panel of the product.
• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the product to rain or moisture.
• Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surface s.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Never connect the product to a dimmer.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord.
• The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the product at higher
temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Never try to repair the product. Repairs carried out by unskilled people can lead to damage or
malfunction. Contact the nearest authorized technical assistance center.
• This product is not intended for permanent installation.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
Auto Program Auto-Ranging Power Supply Replaceable Fuse User-Serviceable
to the next owner.
Page 4 of 21 Freedom™ Par Quad-4 User Manual Rev. 1
Page 5

Description

The Freedom™ Par Quad-4 is a wireless, battery-operated, quad-color LED Par. It can be used as an uplight on the floor or suspended overhead. It has a compact design so it works with TRUSST® and an
Freedom™ Par
compatible controller, the
Power In
Power Out
Fuse Holder
Carry Handle
Microphone

2. INTRODUCTION

Overview

On/Off Switch
DMX In
Kickstand
DMX Out
Infrared Sensor
Glare Shield
Menu
Buttons
adjustable kickstand for easy floor placement. The RGBA LEDs allow for infinite color mixing. The built-in wireless D-Fi™ transmitter and receiver allow wireless Master/Slave control of unlimited Quad-4s. The Freedom™ Par Quad-4 can also be controlled by a D-Fi™­CHAUVET® FlareCON™ Air, or the included IRC-6 remote control.
Display
D-Fi™ AUTO Button
Battery Life Indicator LEDs
Freedom™ Par Quad-4 User Manual Rev. 1 Page 5 of 21
Page 6
5.4 in
5.7 in
7.2 in
138 mm
184 mm

Dimensions

145 mm
Page 6 of 21 Freedom™ Par Quad-4 User Manual Rev. 1
Page 7

AC Power

The Freedom™ Par Quad-4 has an internal auto-ranging power supply and it can work with an input
circuit (circuit breaker or fuse). Make sure the product
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or
Fuse
1. Disconnect the product from power.

Fuse
Replacement

Spare Fuse safety cap)
Installed Fuse
Safety
Cap

3. SETUP

voltage range of 100 to 240 VAC, 50/60 Hz.
Always connect the product to a protected
has an appropriate electrical ground to avoid the risk of electrocution or fire.
dimmer channel serves only as a 0 to 100% switch.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
Replacement
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
Disconnect the product from power before replacing the fuse.
Diagram
Always replace a blown fuse with another of the same type and rating.
A spare fuse is not included; however, the safety cap has room for a spare.
(held by plastic clip)
holder (inside
Freedom™ Par Quad-4 User Manual Rev. 1 Page 7 of 21
Page 8

Power Linking

Daisy chaining products together through their Power In and Power Out sockets, called power linking,
and up to
Charging the
The battery charges whenever the product is plugged into a power source. If the product is plugged in and
Battery Life
The battery life indicators are the 4 small green LEDs on either side of the
> button. The indicators show how much battery life remains available. The drawing below
Battery Run
Maximum Run Time
(all colors on)
Maximum Run Time
(single color on)
Up to 8 hours
Up to 20 hours
6 hours
D-Fi™ AUTO Button
allows many products to be powered from one power outlet
Up to 15 Freedom™ Par Quad-4 products can be power linked at 120 V, 28 Freedom™ Par Quad-4 products can be power linked at 230 V.
not in operation, make sure the On/Off switch is in the Off position.
Battery
D-Fi™ <AUTO
Indicator
provides a key to reading the battery life indicators.
100% 75% 50% 25%
For optimal battery life, charge the Freedom™ Par Quad-4 battery for 24 hours prior to initial use.
Time
Recharge Time
Page 8 of 21 Freedom™ Par Quad-4 User Manual Rev. 1
Page 9

Mounting

Before mounting the product, read and follow the safety recommendations indicated in Safety Notes.

Orientation

The Freedom™ Par Quad-4 has a compa ct design to fit perfectly inside the TRUSST® truss systems. It
Floor
may be mounted in any position;
” of space around it and it is accessible for programming

Rigging

Rig the product from a structure or surface that can support the product’s weight. See Technical
appropriate for
product onto a truss, you should use a mounting clamp of appropriate weight capacity.
cables are away from people
Mounting
Size M12
attaches to 35-50 mm truss without the need for a bracket, using an M12 threaded rigging point. mounting is a cinch with a built-in adjustable kickstand. The product however, place the product so there is at least 20 and control panel operation.
Specifications in this manual for the product’s weight.
When mo unt ing the product overhead, always use a mounting clamp and safety cable. Mount the product securely to a rigging point, such as a pipe or truss. The CHAUVET® CH-05 safety cable is this product.
When riggi ng the The Freedom™ Par Quad-4 has an M12 threaded mounting hole, which is appropriate for this purpose. For the Chauvet line of mounting clamps, go to www.chauvetlighting.com/cables-clamps-main.html/.
When mounting the product on the floor, make sure that the product and any and vehicles.
Threaded Mounting
Hole
Mounting Clamp
(such as the CLP-15 clamp
from Chauvet)
Diagram
Freedom™ Par Quad-4 User Manual Rev. 1 Page 9 of 21
Safety Cable
(such as CH-05 from
Chauvet)
Page 10
Control Panel
To access the control panel functions, use the four buttons located underneath the display.
Button
Function
<MENU>
<UP>
<DOWN>
<ENTER>

Menu Map

The Menu Map outlines the functions available through the menu, the programming levels that can be
4-CH
6-CH
10CH
Static Colors
C--
C 1–C 15
Selects 1 of 15 static colors
Auto Programs
P--
P 1–P 4
Selects 1 of 4 auto program
Program Speed
S--
S 1–S100
Sets auto program speed (slow to fast)
Sound-Active
Snd
Selects Sound-Active mode
Sound Sensitivity
SenS
u 0–u100
Sets sound sensitivity
r 0–r255
Red (0–100%)
g 0–g255
Green (0–100%)
b 0–b255
Blue (0–100%)
A 0–A255
Amber (0–100%)
OFF
(slow), or
dIM1
dIM2
dIM3
On
Off
Automatically select receive frequency (for DMX use)
Manually select receive frequency (for DMX use)
Automatically select transmit fr equen cy (for DMX use)
(for DMX use)

4. OPERATION

Operation
Selects an operation mode Scrolls up the list of options or selects a higher value Scrolls down the list of options or selects a lower value Activates a menu option or a selected value
entered, and a description for each function.
Main Function Programming Levels Description
DMX Personality and
Starting Address
Custom Color Mixing U--
Dimmer dIM
Infrared SET
2.4 GHz D-Fi™ S-tr
d 1–d512
drAS drAU
drCH dr 1–dr16
dtAS dtAU
Selects DMX personality and DMX starting value
Sets the dimming curve: dIM1 (fast) to dIM3 OFF
Turns infrared on or off
dtCH dt 1–dt16
Manually select transmit frequency
Page 10 of 21 Freedom™ Par Quad-4 User Manual Rev. 1
Page 11

DMX Linking

The Freedom™ Par Quad-4 operates by itself in Standalone mode.
ode, both of which require DMX linking. In
ode the lighting
n of the next
products for Master/Slave operation, the DMX controller
is not a part of the DMX daisy chain and the master is the first product in the chain. See

Starting Address

To ensure full access to all channels in each DMX mode, the highest recommended DMX address is 503.
Master/Slave
Master/Slave mode allows a single Freedom™ Par Quad-4 (the master) to control the actions of one or
be set to operate in Slave mode. Once set and connected, the slaves will operate in unison with the
Make the master the first unit in the DMX daisy chain.
• Configure all the slaves to Slave mode before connecting the master to the DMX daisy chain.
• DO NOT connect more than 31 slaves to the master using DMX cable.
DMX
When selecting a starting DMX address, always consider the number of DMX channels the selected DMX
channel mode) or
It also operates in Master/Slave mode, or in DMX m Master/Slave mode the master product sends DMX signals to the slaves. In DMX m control board sends DMX signals to the products.
To DMX-link a number of Freedom™ Par Quad-4 using wireless D-Fi™, see D-Fi™ 2.4 GHz (DMX Mode
Manual Sync).
To DMX link a number of Freedom™ Par Quad-4 using DMX cable
• connect the DMX cable from DMX Out of the board, to DMX In of the first product, or
• connect the DMX cable from DMX Out of the master, to DMX In of the first slave.
Then connect another DMX cable from DMX Out of the first product/slave to DMX I product/slave.
Continue connecting each subsequent product until all the products are part of the chain. Information about DMX is in the DMX Primer, which is available from the Chauvet website
www.chauvetlighting.com/download/
When DMX linking Freedom™ Par Quad-4

Master/Slave Mode for details.

.
Mode
Personalities
more Freedom™ Par Quad-4 units (the slaves) without a DMX controller. The master will be set to operate in either an auto program or Sound-Active mode, while the slaves will
master. Configure the units as indicated below.
Slaves:
1. Press <MENU> repeatedly until any DMX personality shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d 1.
4. Connect the DMX input of the first slave to the DMX output of the master.
5. Connect the DMX input of the subsequent slaves to the DMX output of the previous slave.
6. Finish setting and connecting all the slaves .
Master:
Set the master to operate in either Auto or Sound-Active mode.
• Never connect a DMX controller to a DMX daisy chain of master and slaves.
• Make the master the first unit in the DMX daisy chain.
• Always put the male DMX connector (DMX Out) into the master.
mode uses. If you choose a starting address that is too high, you could restrict the access to some of the product’s channels.
If unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com. To select the DMX personality and starting address, do the following:
1. Press <MENU> repeatedly until 3-CH (3-channel mode), 6-CH (6- 10CH (10-channel mode) shows on the display.
2. Press <ENTER> and d 1–d512 shows on the display.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
Freedom™ Par Quad-4 User Manual Rev. 1 Page 11 of 21
Page 12
D-Fi™ 2.4 GHz
(DMX Mode
The Freedom™ Par Quad-4 series offers wireless control of 2 or more products with a single DMX
). The channel number should match
the transmitting signal you chose when setting up the transmitting product.
To sync multiple transmitters in one room, manually set each receiver and the designated
2.4 GHz wireless transceiver
2.4 GHz User
Manual Sync)
controller. To manually set up the D-Fi™ 2.4 GHz syncing for DMX, do the following. For the transmitting product:
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until dtCH appears on the display.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to select the transmitting signal (dt 1–dt16).
For the receiving product(s):
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until drCH appears on the display.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to select the receiving signal (dr 1–dr16
transmitter to a specific frequency and then perform the syncing steps. Freedom™ Par Quad-4 is fully compatible with the D-Fi™
(transmitter/receiver) from Chauvet (sold separately).
For more detailed information about D-Fi™ 2.4 GHz functionality, refer to the D-Fi™ Manual available at the Chauvet website www.chauvetlighting.com.
Manual syncing is recommended for best results.
Page 12 of 21 Freedom™ Par Quad-4 User Manual Rev. 1
Page 13
D-Fi™ 2.4 GHz
The Freedom™ Par Quad-4 offers wireless control of 2 or more products with a single DMX controller. To
on just the transmitter for approximately 30 seconds. The display and signal LED will flash
You can then back out to a general menu level and configure the transmitting product to operate it with a
To configure your product to work with DMX, refer to the Starting Address section.
• To add additional Freedom™ products, turn the synced ones off and repeat the above steps
quality, keep the line of sight
• Ensure that all linked products are configured to the same DMX personality.
Caution: D-Fi™ 2.4 GHz operation can be interrupted or inhibited by liquid masses between the
(DMX Mode
Auto Sync)
automatically set up D-Fi™ 2.4 GHz syncing for DMX, do the following: For the receiving product(s):
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until drAS appears on the display.
4. Press <ENTER>.
5. The display should show drAU.
For the transmitting product:
1. Press <MENU> repeatedly until S-tr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> until dtAS appears on the display.
4. Press <ENTER>.
5. The display should show dtAU.
Receiving units must be set up before the transmitting unit. Once the steps above are done, press and hold <AUTO> to indicate sync is activated.
DMX controller.
with unsynced products. Once all products are synced, turn them all back on.
• Auto scan syncing must be done within a distance of about 32 ft (10 m).
• Manual syncing is recommended for best results when adding products after initial system
setup.
• If you are experiencing issues or need to improve signal between products unobstructed.
transmitter and receiver such as water, snow, or people. For best results, keep the line of sight clear of any liquid mass.
Freedom™ Par Quad-4 User Manual Rev. 1 Page 13 of 21
Page 14
DMX Channel
Assignments and
The following tables show which DMX channels control which functions in each of the DMX personalities.

10CH

1
Dimmer
000 ó 255
0–100%
2
Red
000 ó 255
0–100%
3
Green
000 ó 255
0–100%
4
Blue
000 ó 255
0–100%
5
Amber
000 ó 255
0–100%
000 ó 010
No function
011 ó 030
R: 100% G: 0–100% B: 0
031 ó 050
R: 100%—0 G: 100% B: 0
051 ó 070
R: 0 G: 100% B: 0–100%
071 ó 090
R: 0 G: 100%–0 B: 100%
091 ó 110
R: 0–100% G: 0 B: 100%
111 ó 130
R: 100% G: 0 B: 100%–0
131 ó 150
R: 100% G: 0–100% B: 0–100%
151 ó 170
R: 100%–0 G: 100%–0 B: 100%
171 ó 200
R:100% G: 100% B: 100% A: 100%
201 ó 205
Color temperature 1
206 ó 210
Color temperature 2
211 ó 215
Color temperature 3
216 ó 220
Color temperature 4
221 ó 225
Color temperature 5
226 ó 230
Color temperature 6
231 ó 235
Color temperature 7
236 ó 240
Color temperature 8
241 ó 245
Color temperature 9
246 ó 250
Color temperature 10
251 ó 255
Color temperature 11
000 ó 010
No function
011 ó 255
0—100%, slow to fast
Be sure to become familiar with these values when operating the product with a DMX controller.
Values
Channel Function Value Setting
6
Color Macros and Color Temperature
7 Strobe
Page 14 of 21 Freedom™ Par Quad-4 User Manual Rev. 1
Page 15
10CH
000 ó 010
No function
011 ó 060
Auto program 1
061 ó 120
Auto program 2
121 ó 180
Auto program 3
181 ó 240
Auto program 4
241 ó 255
Sound-Active mode
Controls auto program speed (slow to fast), or
000 ó 051
Dimmer mode manually set in Menu Options
052 ó 101
Dimmer mode off
102 ó 152
Dimmer mode 1, (fast s peed)
153 ó 203
Dimmer mode 2, (medium speed)
204 ó 255
Dimmer mode 3, (slow speed)

6-CH

Channel
Function
Value
Percent/Setting
1
Dimmer
000 ó 255
0–100%
2
Red
000 ó 255
0–100%
3
Green
000 ó 255
0–100%
4
Blue
000 ó 255
0–100%
5
Amber
000 ó 255
0–100%
000 ó 010
No function
011 ó 255
Slow to fast

4-CH

Channel
Function
Value
Percent/Setting
1
Red
000 ó 255
0–100%
2
Green
000 ó 255
0–100%
3
Blue
000 ó 255
0–100%
4
Amber
000 ó 255
0–100%
Channel Function Value Setting
8 Auto/Sound Programs
9 Auto Speed/Sensitivity
10 Dimmer Mode
6 Strobe
000 ó 255
sound sensitivity when CH. 8 is 241–255
Freedom™ Par Quad-4 User Manual Rev. 1 Page 15 of 21
Page 16
Configuration
Use standalone configuration to operate the product without a DMX controller. There are a variety of
standalone mode can transmit DMX
Sound-Active
Sound-Active mode sets the product to respond to sounds and music.

Sound Sensitivity

To set the sound sensitivity, follow the instructions below:
3. Press <ENTER>.

Auto Mode

Auto mode sets the product to 1 of 4 preset color programs.

Program Speed

To set the auto program speed, follow the instructions below:
3. Press <ENTER>.
Selecting the
To select a dimmer mode, do the following:
Press <ENTER>. 4.

Static Colors

To select a preset static color, do the following:
4. Press <ENTER>.
Custom Color
To custom mix a color, follow the instructions below:
(green),
6. Repeat steps 3 to 5 until you create your desired color.
(Standalone)
Standalone modes and they are powerful tools for making exciting looks.
Never connect a product operating in a standalone mode (Static, Sound-Active, Auto, or Infrared) to a DMX chain that includes a DMX controller. Products in a signals that interfere with the DMX signals from the controller.
Mode
To enable the Sound-Active mode, do the following:
1. Press <MENU> repeatedly until Snd shows on the display.
2. Press <ENTER>.
1. Press <MENU> repeatedly until SenS shows on the display.
2. Use <UP> or <DOWN> to select the desired sound sensitivity (u 0–u100).
The product will respond only to low frequencies of music (bass and drums). If the product is not responding to sound, increase the sensitivity.
To set the product to Auto mode, do the following:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER> and P 1–P 4 shows on the display.
3. Use <UP> or <DOWN> to select the desired auto program:
• P 1 - 3-color snap
• P 2 - 3-color fade
• P 3 - 7-color snap
• P 4 - 7-color fade
4. Press <ENTER>.
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> or <DOWN> to select the desired auto program speed (S 1–S100, slow to fast).
Dimmer Mode
Mixing
Page 16 of 21 Freedom™ Par Quad-4 User Manual Rev. 1
Press <MENU> repeatedly until dIM shows on the display. 1. Press <ENTER> and one of the following shows on the display: 2.
• OFF (dimmer speed off)
• dIM1 (dimmer mode 1, fast speed)
• dIM2 (dimmer mode 2, middle speed)
• dIM3 (dimmer mode 3, slow speed)
Use <UP> or <DOWN> to select the desired dimmer mode. 3.
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the desired preset color (C 1–C 15).
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> and one of the following colors shows on the display: rXXX (red), gXXX bXXX (blue), or AXXX (amber).
3. Press <ENTER> repeatedly to select the desired color.
4. Use <UP> or <DOWN> to select the desired color value (0–255). NOTE: Selecting 0 will turn the color off.
5. Press <ENTER> to select color value and continue to the next color.
Page 17

Infrared Mode

Infrared (IR) mode allows the product to be controlled with an infrared remote controller. The
IRC-6 Operations
Be sure the IRC-6 remote is pointing directly at the product and there is nothing in between the remote and
LEDs. The white, and
s activated. If the remote does not respond when a button
IRC-6 can remotely set the product to various modes; adjust the color, speed and sensitivity; and set the strobe. The Freedom™ Par Quad-4 is compatible with the included IRC-6 from Chauvet. To enable use with the IRC-6,
follow the instructions below:
1. Press <MENU> repeatedly until SET shows on the display.
2. Press <ENTER> and ON (turns on the infrared sensor) or OFF (turns off the infrared sensor) shows on the display.
3. Press <UP> or <DOWN> to select the desired option.
4. Press <ENTER>.
the product.
Automatic Mode
Automatic mode will enable you to run the automatic programs on the product. To turn on Automatic mode:
1. Press <AUTO> on the IRC-6.
2. Press <+> or <–> to choose between the four different auto progra ms. To adjust the speed of the automatic program:
1. Press <SPEED> on the IRC-6.
2. Press <%>.
3. Press <+> or <–> to either increase or decrease the speed of the program.
Sound-Active Mode
Sound-Active mode will enable the product to respond to the music. To turn on Sound-Active mode:
• Press <SOUND> on the IRC-6. To adjust sound sensitivity in Sound-Active mode:
1. Press <SENSITIVITY> on the IRC-6.
2. Press <%>.
3. Press <+> or <–> to either increase or decrease sound sensitivity.
Manual Color Control
To choose a specific color with the IRC-6:
1. Press <MANUAL> on the IRC-6.
2. Press any number between <0> and <9> to choose your color.
To manually control the RGBA percentage:
1. Press <MANUAL> on the IRC-6.
2. Press <R>, <G>, <B>, or <A> (red, green, blue, or amber) to choose your color.
Note: The Freedom™ Par Quad-4 only contains red, green, blue and amber
Note: The IRC-6 will not respond to any inputs when the Black Out mode i
is pressed, try pressing <BLACK OUT>. You may have inadvertently activated the Black Out mode.
UV color options on the IRC-6 will only operate with fixtures capable of outputting these color lights.
3. Press <+> or <–> to increase or decrease the percentage of each color.
Miscellaneous Operation
To adjust the strobe rate of the program:
1. Press <STROBE> on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe.
To choose a fade auto program:
• Press <FADE> repeatedly on the IRC-6 to choose between the two auto program fade options
To black out the lights:
• Press <BLACK OUT> on the IRC-6. This will turn off all the lights until the button is pressed again.
Freedom™ Par Quad-4 User Manual Rev. 1 Page 17 of 21
Page 18
Product
Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of
performance and minimize wear, clean the product at least

5. TECHNICAL INFORMATION

the light source’s life. To maintain optimum
Maintenance
twice a month. However, usage and environmental conditions may require more frequent cleaning. To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external surfaces and vents.
4. Clean all external optics and transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
6. Softly wipe any dirt or grime to the outside edges of the external optics or transparent surface.
7. Gently polish the external optics and transparent surfaces until they are free of haze and lint.
Always dry the lens surfaces carefully after cleaning them.
Page 18 of 21 Freedom™ Par Quad-4 User Manual Rev. 1
Page 19
Dimensions and
Length
Width
Height
Weight
5.4 in (138 mm)
5.7 in (145 mm)
7.2 in (184 mm)
6.2 lb (2.8 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Input Voltage
Range
Voltage Selection
Switching (internal)
100–240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 VAC, 60 Hz
230 VAC, 50 Hz
Consumption
35 W
33 W
Operating current
0.5 A
0.3 A
Power linking current (units)
8 A (15 units)
8 A (28 units)
Fuse
T 1 A, 250 V
T 1 A, 250 V
Power I/O
US/Canada
UK/Worldwide
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power cord plug
Edison (US)
Local plug
LED
Type
Power
Lifespan
LED
5 W
50,000 hours
Color
Quantity
Current
Quad-color RGBA
4
2 A
Photo Optic
Parameter
Field angle
29°
Beam angle
15°
Strobe rate
0 to 17 Hz
Illuminance @ 2 m
2,300 lux
Thermal
Maximum External Temp.
Cooling System
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
4, 6 or 10
Ordering
Product Name
Item Code
UPC Number
Freedom™ Par Quad-4
03030813
781462211615

6. TECHNICAL SPECIFICATIONS

Weight
Freedom™ Par Quad-4 User Manual Rev. 1 Page 19 of 21
104 °F (40 °C) Convection
Page 20
R
To return a product or request support:
contact your distributor of record
products to them. Visit our website for
Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and
epaid, in its original box, and with its original packing and accessories.
will refuse any product returned without an RMA
ly affixed label. DO NOT write the RMA number directly on the
Before sending the product, clearly write the following information on a piece of paper and place it inside
properly. Any shipping damage resulting from inadequate packaging will be
ETURNS
• In the U.S., contact Chauvet World Headquarters (see Contact Us).
• In the UK or Ireland, contact Chauvet Europe Ltd. (see Contact Us).
• In Mexico, contact Chauvet Mexico (see Contact Us).
• In any other country, DO NOT contact Chauvet. Contact your distributor. See www.chauvetlighting.com
for distributors outside the U.S., United Kingdom, Ireland, or Mexico.
If you live outside the U.S., United Kingdom, Ireland, or Mexico, and follow their instructions on how to return Chauvet contact details.
a brief description of the cause for the return. You must send the merchandise pr
Chauvet will not issue call tags. Clearly label the package with the RMA number. Chauvet
number.
Write the RMA number on a proper box.
the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product your responsibility. FedEx packing or double-boxing is recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned product(s).
Page 20 of 21 Freedom™ Par Quad-4 User Manual Rev. 1
Page 21
C
WORLD HEADQUA R TERS - Chauvet
General Information
Toll free: (800) 762-1084
Technical Support
World Wide Web www.chauvetlighting.com
UNITED KIN GDOM AND IRE LAND - Chauvet Europe Ltd.
General Information
Fax: +44 (0)1773 511110
Technical Support
MEXICO - Chauvet Mexico
General Information
Voice: +52 (728) 285-5000
Technical Support
Outside the U.S., United Kingdom, Ireland, or Mexico, contact your dealer. Follow their instructions to request
ONTACT
US
Address: 5200 NW 108th Avenue Sunrise, FL 33351 Voice: (954) 577-4455 Fax: (954) 929-5560
Address: Unit 1C Brookhill Road Industrial Estate Pinxton, Nottingham, UK NG16 6NT Voice: +44 (0)1773 511115
Address: Av. Santa Ana 30 Parque Industrial Lerma Lerma, Mexico C.P. 52000
support or to return a product. Visit our website for contact details.
Voice: (954) 577-4455 (Press 4) Fax: (954) 756-8015 Email: tech@chauvetlighting.com
Email: uktech@chauvetlighting.com
World Wide Web www.chauvetlighting.co.uk
Email: servicio@chauvet.com.mx
World Wide Web www.chauvet.com.mx
Freedom™ Par Quad-4 User Manual Rev. 1 Page 21 of 21
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use