Page 1
User Manual
Page 2
Table of Contents
COLORband T3BT ILS
1. Before You Begin .......................................................................
What Is Included ........................................................................................... 1
Unpacking Instructions.................................................................................. 1
Claims ............................................................................................................................ 1
Text Conventions .......................................................................................... 1
Symbols ........................................................................................................ 1
Disclaimer ..................................................................................................... 1
Safety Notes.................................................................................................. 2
FCC Compliance............................................................................................................ 2
RF Exposure Warning for North America and Australia................................................. 2
2. Introduction ................................................................................ 3
Product Overview.......................................................................................... 3
Product Dimensions ...................................................................................... 3
3. Setup ........................................................................................... 4
AC Power...................................................................................................... 4
Fuse Replacement ......................................................................................................... 4
Power Linking................................................................................................................. 4
Mounting ....................................................................................................... 5
Orientation...................................................................................................................... 5
Rigging ........................................................................................................................... 5
4. Operation .................................................................................... 6
Control Panel Operation................................................................................ 6
Menu Map ..................................................................................................... 6
Configuration (DMX) ..................................................................................... 6
DMX Personality and Starting Address.......................................................................... 6
D-Fi USB Connectivity .................................................................................. 7
D-Fi USB Compatibility .................................................................................................. 7
Configuration (D-Fi USB) ............................................................................................... 7
DMX Values .................................................................................................. 8
Configuration (Standalone) ........................................................................... 9
Preset Color Mode ......................................................................................................... 9
Automatic Programs....................................................................................................... 9
Auto-Program Speed ..................................................................................................... 9
Dimmer........................................................................................................................... 9
Sound-Active Programs ................................................................................................. 9
Sound Sensitivity............................................................................................................ 9
Custom Color Mixing...................................................................................................... 9
IRC-6 Infrared Remote Control ..................................................................... 10
IRC-6 Operation ............................................................................................................. 10
Bluetooth Control .......................................................................................... 10
Master/Slave Mode ....................................................................................... 11
Master/Slave Mode (D-Fi USB)..................................................................... 11
ILS Mode....................................................................................................... 11
5. Maintenance................................................................................ 12
Product Maintenance .................................................................................... 12
6. Technical Specifications ........................................................... 13
Contact Us ...................................................................................... 14
Warranty & Returns....................................................................................... 14
1
COLORband T3BT ILS User Manual Rev. 1
Page 3
Before You Begin
!
1. Before You Begin
What Is Included
• COLORband T3BT ILS
• Power cable
Unpacking Instructions
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate the claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Text Conventions
Convention Meaning
1–512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
<ENTER> A key to be pressed on the product’s control panel
ON A value to be entered or selected
• Quick Reference Guide
Symbols
Symbol Meaning
Electrical warning. Not following these instructions may cause electrical damage to
the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetdj.com
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2023 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, and COLORband T3BT ILS are registered trademarks or trademarks of
Chauvet & Sons LLC. (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries.
Other company and product names and logos referred to herein may be trademarks of their respective
companies.
.
COLORband T3BT ILS User Manual Rev. 1
1
Page 4
Before You Begin
Safety Notes
■ ALWAYS:
♦ Connect to a grounded circuit.
♦ Connect to operating voltages as specified on the product's spec sticker.
♦ Disconnect from power before replacing the fuse.
♦ Disconnect from its power source during periods of inactivity.
♦ Use a safety cable when suspending overhead.
♦ Heed all restrictions and warnings on the spec sticker.
♦ Mount in a location with at least 20 in (50 cm) of ventilation.
♦ Replace the fuse with the same type and rating.
♦ Use a clamp with a captive bolt when a single hanging bracket is used.
■ In the event of a serious operating problem, stop using immediately.
■ DO NOT:
♦ Open this product or attempt any repairs. It contains no user-serviceable parts.
♦ Look at the light source when the product is on.
♦ Use if the power cord is crimped or damaged.
♦ Disconnect by pulling on the power cord.
♦ Allow flammable materials close to the product when it is operating.
♦ Touch the housing when it is on.
♦ Block any ventilation holes/slots in the housing.
♦ Connect to a dimmer or rheostat.
♦ Carry the product by its power cord.
♦ Operate in temperatures higher than 104°F (40°C).
♦ Expose to environments that exceed the Ingress Protection (IP) rating.
♦ Expose to rain or moisture.
♦ Use outdoors.
♦ Submerge.
♦ Leave outdoors for extended periods of time.
♦ Expose to corrosive environmental conditions such as temperature, humidity, salinity,
pressure, radiation, or shock.
♦ Set this product on a flammable surface.
FCC Compliance
This device complies with Part 15 Part B of the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
RF Exposure Warning for North America and Australia
Warning! This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20 cm between
the radiator and the user. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter
Keep this User Manual for future use. If the product is sold to someone else, be sure that they
also receive this document.
2
COLORband T3BT ILS User Manual Rev. 1
Page 5
Introduction
3-pin DMX
in/ out
Display screen
Mounting
bracket
Bracket adjustment
knob (2x)
Menu
buttons
D-Fi USB Port
Power in/ out
Fuse holder
Antenna
Safety loop
Microphone
22.1 in
562 mm
24.2 in
615 mm
5.5 in
140 mm
2 in
50mm
39.3 in
1000 mm
3.8 in
98 mm
3.1 in
78 mm
2. Introduction
Product Overview
Product Dimensions
COLORband T3BT ILS User Manual Rev. 1
3
Page 6
Setup
!
1st product
2
nd
product
3
rd
product
Additional COLORband T3BT ILS products
!
3. Setup
AC Power
The COLORband T3BT ILS has an auto-ranging power supply and can work with an input voltage range
of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet,
and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the
product’s specifications chart. The listed current rating indicates the product’s average current draw under
normal conditions.
• Always connect the product to a protected circuit (a circuit breaker or fuse).
Make sure the product has an appropriate electrical ground to avoid the risk of
electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of nonuse completely disconnect the product from power via breaker or by
unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse Replacement
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the safety cap out of the housing.
4. Remove the blown fuse from the clip on the front of the safety cap and replace with a fuse of the
exact same type and rating.
5. Re-insert the fuse holder and reconnect power.
Power Linking
The product provides power linking via the Edison outlet located in the back of the product. Please see the
diagram below for further explanation.
Power-Linking Diagram
It is possible to power link up to 13 COLORband T3BT ILS products on 120 VAC or
up to 24 COLORband T3BT ILS products on 230 VAC.
The power-linking diagram corresponds to the North American version of the
product ONLY! If using the product in other markets, consult with the local Chauvet
distributor,
as power-linking connectors and requirements may differ by country or region.
4
COLORband T3BT ILS User Manual Rev. 1
Page 7
Setup
Mounting bracket
Safety cable
(such as CH-05 from Chauvet)
Mounting clamp
(such as CLP-15 or CLP-15N from
Chauvet)
Bracket
adjustment knob
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
Orientation
The COLORband T3BT ILS may be mounted in any position; however, make sure adequate ventilation is
provided around the product.
Rigging
• Before deciding on a location for the product, always make sure there is easy access to the product
for maintenance and programming purposes.
• Mount the product on a structure or surface that can support the produt’s weight. (see the Te ch n ic a l
Specifications for weight specifications).
• Always use a safety cable when mounting the product overhead. Mount the product securely to a
rigging point, whether an elevated platform or a truss.
• Use a mounting clamp of appropriate weight capacity when rigging the product onto a truss.
• When power linking multiple products, mount the products close enough for power-linking cables to
reach.
• The bracket adjustment knobs allow for directional adjustment when aiming the product to the
desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the
knobs.
Mounting Diagram
COLORband T3BT ILS User Manual Rev. 1
5
Page 8
Operation
4. Operation
Control Panel Operation
To access the control panel functions, use the four buttons located next to the display. Please refer to the
Product Overview
Button Function
<MENU> Exits from the current menu or function
<UP> Navigates upwards through the menu list and increases the numeric value when in a function
<DOWN>
<ENTER>
Menu Map
Refer to the COLORband T3BT ILS product page on www.chauvetdj.com for the latest menu map.
Mode Programming Levels Description
DMX Mode
ILS Mode iLS iLS1–4 Sets ILS mode
Static
Colors
Automatic
Programs
Auto
Speed
Dimmer dIM L. 1–255 Dimmer
Sound-
Active
Mode
Sensitivity SEnS u 0–100 Sound sensitivity
Custom
Color
Mixing
Bluetooth
Mode*
Control
Mode
*The
Bluetooth®
marks by Chauvet & Sons, LLC is under license. Other trademarks and trade names are those of their respective owners.
Configuration (DMX)
The COLORband T3BT ILS works with a DMX controller. Information about DMX is in the CHAUVET
DMX Primer, which is available from the Chauvet website: www.chauvetdj.com.
DMX Personality and Starting Address
When selecting a starting DMX address, always consider the number of DMX channels the selected DMX
mode uses.
The COLORband T3BT ILS uses up to 13 DMX channels in a 13Ch DMX mode, which defines the highest
configurable address to 500.
For more information about the DMX protocol, download the DMX Primer from: www.chauvetdj.com
To select the starting address, do the following:
1. Press <MENU> repeatedly until 3Ch, 5Ch or 13Ch shows on the display.
2. Press <ENTER> and d 1–500 will show on the display.
3. Use <UP> or <DOWN> to select the starting address.Press <ENTER>.
to see the button locations on the control panel.
Navigates downwards through the menu list and decreases the numeric value when in a function
Enables the currently displayed menu or sets the currently selected value into the selected function
3Ch d 1–510 4-channel DMX mode
5Ch d 1–508 6-channel DMX mode
13Ch d 1–500 16-channel DMX mode
C-- C 1–19 Static colors
P-- P 1–8 Automatic programs
S-- S. 1–100 Program speed for P 1–8
Snd Snd1–8 Sound-active programs
r. 0–255
u--
bLE _ _ _ _ _ Bluetooth control mode, displays Bluetooth ID
SEt
word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such
Choosing a starting address that is too high could restrict the access to some of the product’s channels
G. 0–255
b. 0–255
S. 0–100 Strobe rate
ir
out
on
oFF
SLAV Enable Master/Slave with other BT products
dMX Enable Master/Slave with non-BT products
Custom static colors combine red, green, blue, and
amber
Turns infrared on or off
.
.
6
COLORband T3BT ILS User Manual Rev. 1
Page 9
Operation
Receiving
Receiving
Transmitting
Transmitting
D-Fi USB Connectivity
The COLORband T3BT ILS is able to become a D-Fi wireless receiver/transmitter with the use of the D-Fi
USB from Chauvet DJ. Simply set the product's DMX Personality and DMX Address, set the DIP switch DFi receiving/transmitting channel, then plug it into the D-Fi USB port.
WARNING! DO NOT plug anything other than a D-Fi USB into the USB port. Doing so may
cause damage to the product.
Once plugged in, the D-Fi USB will take over the product. Wired DMX and manual display
control / menu buttons will be unavailable until the D-Fi USB is unplugged. The priority
levels are:
1. D-Fi USB
2. Wired DMX
3. Manual Digital Display/Menu Buttons
D-Fi USB Compatibility
The D-Fi USB can receive a DMX signal from the D-Fi Hub and the FlareCON Air 2 as well as other D-Fi
USB products.
Configuration (D-Fi USB)
1. Set the DMX Personality and DMX address on the COLORband T3BT ILS .
2. Use the Chart provided to set BOTH:
• the Channel, and
• the Receiving or Transmitting option
DIP Switch 5
is for Transmitting OR Receiving, please choose carefully.
D-Fi USB DIP Switch Channels
Ch. 1 2 3 4 T/R Ch. 1 2 3 4 T/R Ch. 1 2 3 4 T/R Ch. 1 2 3 4 T/R
1 9 1 9
2 10 2 10
3 11 3 11
4 12 4 12
5 13 5 13
6 14 6 14
7 15 7 15
8 16 8 16
COLORband T3BT ILS User Manual Rev. 1
7
Page 10
DMX Values
1 23
3Ch 5Ch 13Ch Function Value Percent/Setting
11–Red 000
22–Green 000
3 3 – Blue 000
––1Red 1 000
––2Green 1 000
––3Blue 1 000
––4Red 2 000
––5Green 2 000
––6Blue 2 000
––7Red 3 000
––8Green 3 000
––9Blue 3 000
– 5 10 Strobe
– – 11 Auto programs
– – 12 Auto speed
4 13 Dimmer 000
Zones for DMX Control
255 0–100%
255 0–100%
255 0–100%
255 0–100%
255 0–100%
255 0–100%
255 0–100%
255 0–100%
255 0–100%
255 0–100%
255 0–100%
255 0–100%
000
015 No function
016
255 0–100%
000
005 No function
006
036 Auto Program 1 (programs 2-7)
037
068 Auto Program 2
069
100 Auto Program 3
101
132 Auto Program 4
133
164 Auto Program 5
165
196 Auto Program 6
197
228 Auto Program 7
229
255 Auto Program 8
000
250 Program speed, slow to fast
251
255 Sound-active mode
255 0–100%
Operation
8
COLORband T3BT ILS User Manual Rev. 1
Page 11
Operation
Configuration (Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
Never connect a product that is operating in any standalone mode to a DMX string
connected to a DMX controller. Products in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
Preset Color Mode
To run the COLORband T3BT ILS on a static color, follow the instructions below:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select a static color, from C 1–19.
4. Press <ENTER>.
Automatic Programs
To run the COLORband T3BT ILS in automatic mode, follow the instructions below:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select an automatic program, from P 1–8.
4. Press <ENTER>.
Auto-Program Speed
To change the auto-program speed on the COLORband T3BT ILS , do the following:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> or <DOWN> to increase or decrease the program speed, from S. 1–100.
3. Press <ENTER>. The product will return to the last selected mode.
Dimmer
To set the dimmer curve, follow the instructions below:
1. Press <MENU> repeatedly until diM shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to increase or decrease the dimmer, from L. 1–255.
4. Press <ENTER>.
Sound-Active Programs
To run the COLORband T3BT ILS with a sound-active program, follow the instructions below.
1. Press <MENU> repeatedly until Snd shows on the display.
2. Use <UP> or <DOWN> to set the Sound-Active program, from Snd1–Snd8.
3. Press <ENTER>.
Sound Sensitivity
To set the sound sensitivity on the COLORband T3BT ILS , do the following:
1. Press <MENU> repeatedly until SEnS shows on the display.
2. Use <UP> or <DOWN> to increase or decrease the sound sensitivity, from u 0–100.
3. Press <ENTER>.
Custom Color Mixing
To custom mix a static color, do the following:
1. Press <MENU> repeatedly until u-- shows on the display.
2. Press <ENTER> and one of the following will show on display.
• r._ _ _ (red)
• G._ _ _ (green)
• b._ _ _ (blue)
•S._ _ _ (Strobe)
3. Press <ENTER> to cycle through the color settings.
4. When the desired color shows on the display, use <UP> or <DOWN> to increase or decrease the
color value, from 0–255 (red, green, blue) or 0–100 (Strobe).
5. Repeat steps 3 and 4 until the product outputs as desired.
COLORband T3BT ILS User Manual Rev. 1
9
Page 12
Operation
BLACK
OUT
AUTO
SOUND
SENSITIVITY
SPEEDSTROBE
%
MANUAL
FADE
RGB
WUVA
+
0
-
123
654
789
IRC-6 Infrared Remote Control
The COLORband T3BT ILS can be operated with the CHAUVET IRC-6. To enable IR wireless control,
follow the instructions below.
1. Press <MENU> repeatedly until SEt shows on the display.
2. Press <ENTER>.
3. Press <UP> repeatedly until ir shows on the display.
4. Press <ENTER>.
5. Press <UP> or <DOWN> repeatedly until on or oFF shows on the display.
6. Press <ENTER>.
IRC-6 Operation
Automatic Mode
To turn on Automatic mode with the IRC-6:
1. Press <AUTO> on the IRC-6.
2. Press <+> or <–> to change program.
Sound-Active Mode
To turn on Sound-Active mode with the IRC-6:
1. Press <SOUND> on the IRC-6.
2. Press <+> or <–> to increase or decrease the sensitivity.
To adjust the sound sensitivity:
1. Press <SENSITIVITY> on the IRC-6.
2. Press <+> or <–> to increase or decrease the sensitivity.
Strobe
To turn on Strobe mode with the IRC-6:
1. Press <STROBE> on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe speed.
Manual Control
To manually select the laser color with the IRC-6:
1. Press the desired color, from
To manually select the laser pattern with the IRC-6:
1. Select a manual color.
2. Press <+> or <–> to cycle through the patterns.
Black Out
To black out the lights with the IRC-6:
1. Press <BLACK OUT> on the IRC-6.
This will turn off all the lights until the button is pressed again.
NOTE: The IRC-6 will not respond to any inputs when Black Out is activated. If the
product does not respond when a button is pressed, try pressing <BLACK OUT>.
Black Out may have been activated.
<R>
(red),
<G>
(green),
<B>
(blue), or
<A>
(amber).
Bluetooth Control
Bluetooth control mode allows users to control one or more COLORband T3BT ILS products via Bluetooth
connection on the BTAir app.
To operate the product via Bluetooth control mode:
10
• Any setting on the IRC-6 will be saved until the system is rebooted. The system will
revert to Auto Mode after reboot.
• The buttons on the IRC-6 not listed above are reserved for future use.
1. Press <MENU> repeatedly until bLE shows on the display.
2. Press <ENTER>.
3. Use the ID number on the display to identify the product on the BTAir app.
• Ensure that all products are set to Bluetooth control mode prior to operating the
BTAir app, as failure to do so may require restarting the app.
• For further instructions on how to pair and operate products with the BTAir app,
download the BTAir User Manual from www.chauvetdj.com
.
COLORband T3BT ILS User Manual Rev. 1
Page 13
Operation
Master/Slave Mode
The Master/Slave mode allows a single COLORband T3BT ILS product (the “master”) to control the
actions of one or more COLORband T3BT ILS products (the “slaves”) without the need of a DMX
controller. The master product will be set to operate in Standalone, whereas the slave products will be set
to operate in Slave mode. Once set and connected, the slave products will operate in unison with the
master product. Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 3-CH shows on the display.
2. Press <ENTER>.
3. Set the DMX address to d 1.
4. Connect the DMX input of the first slave product to the DMX output of the master product.
5. Connect the DMX input of the subsequent slave products to the DMX output of the previous slave product.
6. Finish setting and connecting all the slave products.
Master product:
1. Press <MENU> repeatedly to go to the desired function or program.
2. Press <ENTER>.
3. Set the master product to operate in standalone.
4. Make the master product the first product in the DMX daisy chain.
• Configure all the slave products before connecting the master to the daisy chain.
• Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the master.
• Do not connect more than 18 slaves to the master.
Master/Slave Mode (D-Fi USB)
The D-Fi USB allows a single COLORband T3BT ILS product (the “master”) to control the actions of one or more
COLORband T3BT ILS products (the “slaves”) without the need of a DMX controller or DMX cables. The master
(transmitter) product will be set to operate in standalone mode, while the slave (receiver) products will be set to
operate in DMX mode. Once set and connected, the slave products will operate in unison with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 3-CH shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to set the starting address to d 1.
4. Press <ENTER>.
5. Set the D-Fi USB to receive on a specific channel, 1–16.
6. Plug in the D-Fi USB.
7. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to operate in standalone mode.
2. Set the D-Fi USB to transmit on the D-Fi channel the slaves are receiving on.
3. Plug in the D-Fi USB.
• All products must be set to the same DMX personality, DMX address, and D-Fi channel.
• Configure all the slave products before configuring the master to transmit.
• Never connect a DMX controller to a D-Fi channel configured for Master/Slave operation
because the controller may interfere with the signals from the master.
ILS Mode
ILS (Integrated Lighting System) provides 4 modes that synchronize with the GigBAR MOVE+ILS: Modes
1 and 3 synchronize with side 1 of the GigBAR MOVE+ILS, whereas modes 2 and 4 synchronize with side
2 of the GigBAR MOVE+ILS. When linked, effects will sync with the most similar effect on the selected side
of the GigBAR MOVE+ILS: Kinta effects will sync with one of the kintas, moving heads will sync with one of
the moving heads, and wash effects will sync with one of the pars. Laser effects will sync with the laser,
and strobe effects will sync with the strobe effects regardless of ILS mode.This product will synchronize
with the par effect on the selected side of the GigBAR MOVE+ILS.
To set the COLORband T3BT ILS to respond to an ILS signal:
1. Press <MENU> repeatedly until iLS shows on the display.
2. Use <UP> or <DOWN> to select from iLS1 (side 1), iLS2 (side 2), iLS3 (side 1), or iLS4 (side 2).
3. Press <ENTER>.
COLORband T3BT ILS User Manual Rev. 1
11
Page 14
Maintenance
5. Maintenance
Product Maintenance
Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of
the light source’s life and/or mechanical wear. To maintain optimum performance and minimize wear, clean
all lighting products at least twice a month. However, be aware that usage and environmental conditions
could be contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external
surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens-cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.
12
COLORband T3BT ILS User Manual Rev. 1
Page 15
Technical
6. Technical Specifications
Dimensions and Weight
Length Width Height Weight
39.3 in (1000 mm) 3.8 in (98 mm) 5.5 in (140 mm) 6.6 lb (3 kg)
Note: Dimensions in inches rounded to the nearest hundredth.
Power
Power Supply Type Range Voltage Selection
Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging
Parameter 120 V, 60 HZ 230 V, 50 HZ
Consumption 43 W 41 W
Operating current 0.6 A 0.3 A
Power-linking current (products) 8 A (13 products) 8 A (24 products)
Fuse T 2A, 250 V T 2A, 250 V
Power I/O U.S./Canada Worldwide
Power input connector IEC IEC
Power output connector Edison IEC
Power cord plug Edison (U.S.) Local plug
Light Source
Type Quantity Color Power Current Lifespan
LED 12 Tri-color RGB 3 W 1 A 50,000 hours
Photometrics
Parameter Value
Strobe rate 0 to 25 Hz
Beam angle 53°
Coverage angle 112°
Illuminance @ 2 m 433 lux
Thermal
Maximum External Temperature Cooling System
104 °F (40 °C) Convection
DMX
I/O Connector Channel Range
3-pin XLR 3, 15, or 13
Ordering
Product Name Item Code UPC Number
COLORband T3BT ILS 10032063
7814622241
COLORband T3BT ILS User Manual Rev. 1
13
Page 16
Contact Us
Chauvet World Headquarters
Chauvet U.K.
Chauvet Benelux
Chauvet France
Chauvet Germany
Chauvet Mexico
Address: Av. de las Partidas 34 - 3B
Lerma, Edo. de México, CP 52000
General Information Technical Support
Address: 3360 Davie Rd. Voice: (844) 393-7575
Davie, FL 33314 Fax: (954) 756-8015
Voice: (954) 577-4455 Email: chauvetcs@chauvetlighting.com
Fax: (954) 929-5560
Toll Free: (800) 762-1084 Website: www.chauvetdj.com
Address: Pod 1 EVO Park
Little Oak Drive, Sherwood Park
Nottinghamshire, NG15 0EB
U.K.
oice: +44 (0) 1773 511115 Fax:
V
+44 (0) 1773 511110
Address: Stokstraat 18 Email: BNLtech@chauvetlighting.eu
9770 Kruishoutem
Belgium Website: www.chauvetdj.eu
Voice: +32 9 388 93 97
Address: 3, Rue Ampère
91380 Chilly-Mazarin
France Website: www.chauvetdj.eu
Voice: +33 1 78 85 33 59
Address: Bruno-Bürgel-Str. 11
Voice: +49 421 62 60 20
Voice: +52 (728) 690-2010
28759 Bremen
Germany Website: www.chauvetdj.eu
(Entrance by Calle 2)
Zona Industrial Lerma Website: www.chauvetdj.mx
Email: UKtech@chauvetlighting.eu
Website: www.chauvetdj.eu
Email: FRtech@chauvetlighting.fr
Email: DEtech@chauvetlighting.de
Email: servicio@chauvet.com.mx
Contact Us
Warranty & Returns
For warranty terms and conditions and return information, please visit our website.
For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration
For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg,
France, and Germany: www.chauvetlighting.eu/warranty-registration
14
COLORband T3BT ILS User Manual Rev. 1
.
.
Loading...