Page 1
User Manual
Page 2
Table of Contents
TABLE OF CONTENTS
1. Before You Begin ......................................................................................... 1
What Is Included ...................................................................................................... 1
Unpacking Instructions............................................................................................. 1
Claims ............................................................................................................................ 1
Text Conventions ..................................................................................................... 1
Symbols ................................................................................................................... 1
Disclaimer ................................................................................................................ 1
Intellectual Property ................................................................................................. 1
Safety Notes............................................................................................................. 2
2. Introduction................................................................................................... 3
Product Overview..................................................................................................... 3
Product Dimensions................................................................................................. 3
3. Setup.............................................................................................................. 4
AC Power ................................................................................................................. 4
Power Linking................................................................................................................. 4
Mounting .................................................................................................................. 5
Orientation...................................................................................................................... 5
Rigging ........................................................................................................................... 5
4. Operation....................................................................................................... 6
Control Panel Operation........................................................................................... 6
Menu Map ................................................................................................................ 6
Configuration (DMX) ................................................................................................ 6
Starting Address............................................................................................................. 6
DMX Channel Assignments and Values .................................................................. 7
Configuration (Standalone) ...................................................................................... 9
Automatic Program ........................................................................................................ 9
Auto Program Speed ...................................................................................................... 9
Static Color Mode........................................................................................................... 9
Custom Color Mixing...................................................................................................... 9
Dimmer........................................................................................................................... 9
Screen Lock ................................................................................................................... 9
Factory Reset................................................................................................................. 9
Master/Slave Mode .................................................................................................. 10
5. Maintenance.................................................................................................. 11
Product Maintenance ............................................................................................... 11
6. Technical Specifications.............................................................................. 12
Returns.............................................................................................................. 13
Contact Us......................................................................................................... 14
COLORband Q4 IP User Manual Rev. 2
Page 3
Before You Begin
1. Before You Begin
What Is Included
• COLORband Q4 IP
•Power cord
• Quick Reference Guide
Unpacking Instructions
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Text Conventions
Convention Meaning
1–512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
<ENTER> A key to be pressed on the product’s control panel
ON A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetdj.com
.
Intellectual Property
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2021 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, and COLORband Q4 IP are registered trademarks or trademarks of Chauvet &
Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company
and product names and logos referred to herein may be trademarks of their respective companies.
COLORband Q4 IP User Manual Rev. 2
Page 1 of 14
Page 4
Safety Notes
• This product is not intended for permanent installation.
• Do not submerge this product (IP65). Temporary outdoor operation is fine.
• When using this product in an outdoor environment, use IP65- (or higher) rated power and data
cables. Secure unused power and data ports with attached IP65 covers.
• Not for permanent outdoor installation in locations with extreme environmental conditions. This
includes, but is not limited to:
• Exposure to marine/saline environment (within 3 miles of saltwater body of water).
• Locations where the normal high or low temperatures exceed the temperature ranges
• Locations that are prone to flooding or being buried in snow.
• Areas where the product will be subjected to extreme radiation or caustic substances.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power by pulling or tugging on the cord.
• If mounting the product overhead, always secure to a fastening device using a safety cable.
• Make sure there are no flammable materials close to the product when operating.
• Do not touch the product’s housing when operating because it may be very hot.
• The voltage of the outlet to which you are connecting this product must be within the range
stated on the decal or rear panel of the product.
• Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from
adjacent surfaces.
• Never connect the product to a dimmer or rheostat.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord or any moving part. Always use the bracket.
• The maximum ambient temperature is 104 °F (40 °C). Do not operate this product at higher
temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Do not open this product. It contains no user-serviceable parts.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
Before You Begin
in this manual.
Keep this User Manual for future use. If the product is sold to someone else, be sure that they
also receive this document.
Page 2 of 14
COLORband Q4 IP User Manual Rev. 2
Page 5
Introduction
DMX
in
DMX
out
Power
out
Display
Power
in
Menu
buttons
Bracket
adjustment
knob (2x)
Mounting
bracket (2x)
4.1 in
104 mm
3.2 in
81 mm
39.3 in
998 mm
2. Introduction
Product Overview
Product Dimensions
COLORband Q4 IP User Manual Rev. 2
Page 3 of 14
Page 6
Setup
1st product
2
nd
product
3
rd
product
Additional
products
Power
source
3. Setup
AC Power
The COLORband Q4 IP has an auto-ranging power supply, and it can work with an input voltage range of
100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current
value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
The listed current rating indicates the product’s average current draw under normal conditions.
• Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure
the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
Power Linking
The product provides power linking via the outlet located in the back of the product. See the diagram below
for further explanation.
Power Linking Diagram
Page 4 of 14
You can power link up to 9 COLORband Q4 IP products on 120 VAC or up to 16 products
on 230 VAC.
COLORband Q4 IP User Manual Rev. 2
Page 7
Setup
Safety cable
(such as CH-05
from Chauvet)
Mounting clamp
(such as CLP-15 from Chauvet)
Mounting bracket
Bracket adjustment
knob (x2)
Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.
Orientation
The COLORband Q4 IP may be mounted in any position; however, make sure adequate ventilation is
provided around the product.
Rigging
• Before deciding on a location, always make sure there is easy access to the product for
maintenance and programming.
• Make sure adequate ventilation is provided around the product.
• Make sure that the structure or surface onto which you are mounting the product can support the
product’s weight (see the Technical Specifications
• When mounting the product overhead, always use a safety cable. Mount the product securely to a
rigging point, whether an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
• When power linking multiple products, mount the products close enough for power-linking cables to
reach.
•
The bracket adjustment knobs allow for directional adjustment when aiming the product to the desired
angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the knobs.
Mounting Diagram
).
COLORband Q4 IP User Manual Rev. 2
Page 5 of 14
Page 8
Operation
4. Operation
Control Panel Operation
To access the control panel functions, use the four buttons located underneath the display. Refer to the
Product Overview to see the button locations on the control panel.
Button Function
<MENU> Exits from the current menu or function
<UP> Navigates upwards through the menu list or increases a selected numeric value
<DOWN> Navigates downwards through the menu list or decreases a selected numeric value
<ENTER> Enables the currently displayed menu or sets a selected value into the selected function
Menu Map
Refer to the COLORband Q4 IP product page on
Mode Programming Levels Description
4CH d. 1–509
7CH d. 1–506
DMX Mode
Static Color C-- C 1–19 Static colors
Auto
Program
Auto Speed S-- S. 1–100 Program speed for P 1–11
Custom
Color Mixing
Dimmer
Mode
Control
Mode
10CH d. 1–503
16CH d. 1–497
22CH d. 1–491
P-- P 1–11 Automatic programs
r. 0–255
u--
dIM
SEt
G. 0–255
b. 0–255
A. 0–255
oFF
dIM1–3
PASS
rESt
www.chauvetdj.com
Sets the DMX personality and starting address
Adjust the red, green, blue, and amber levels to
create custom colors
Sets the dimmer curve: dIM1 (fast) to dIM3 (slow),
or OFF
oFF Deactivates password protection to unlock screen
on
no
YES
Activates password protection to lock screen
Password: <UP>, <DOWN>, <UP>, <DOWN>,
<ENTER>
Resets the product to factory defaults
for the latest menu map.
Configuration (DMX)
The COLORband Q4 IP works with a DMX controller. Information about DMX is in the CHAUVET DMX
Primer, which is available from the Chauvet website http://www.chauvetlighting.com/downloads/
DMX_Primer_rev05_WO.pdf.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels the selected DMX
mode uses. If you choose a starting address that is too high, you could restrict the access to some of the
product’s channels.
The COLORband Q4 IP uses up to 22 DMX channels, which defines the highest configurable address as
Download the DMX Primer from www.chauvetdj.com to know more about the DMX protocol.
To select the starting address, do the following:
1. Press <MENU> repeatedly until 4Ch, 7Ch, 10Ch, 16Ch, or 22Ch shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address, from d. 1–509.
4. Press <ENTER>.
Page 6 of 14
COLORband Q4 IP User Manual Rev. 2
491
.
Page 9
Operation
Zone 1
Zone 2
Zone 3
Zone 4
DMX Channel Assignments and Values
16CH 22CH Function Value Percent/Setting
– 1 Dimmer 000 255 0–100%
1 2 Red 1 000 255 0–100%
2 3 Green 1 000 255 0–100%
3 4 Blue 1 000 255 0–100%
4 5 Amber 1 000 255 0–100%
5 6 Red 2 000 255 0–100%
6 7 Green 2 000 255 0–100%
7 8 Blue 2 000 255 0–100%
8 9 Amber 2 000 255 0–100%
9 10 Red 3 000 255 0–100%
10 11 Green 3 000 255 0–100%
11 12 Blue 3 000 255 0–100%
12 13 Amber 3 000 255 0–100%
13 14 Red 4 000 255 0–100%
14 15 Green 4 000 255 0–100%
15 16 Blue 4 000 255 0–100%
16 17 Amber 4 000 255 0–100%
– 18 Color macros
–19Strobe
– 20 Automatic programs
– 21 Program speed 000 255 Automatic program speed, slow to fast
– 22 Dimmer speed mode
000 010 No function
011 255 Color macros
000 015 No function
016 255 Strobe, slow to fast
000 005 No function
006 028 Automatic program 1 (4-color snap)
029 051 Automatic program 2 (4-color fade)
052
074 Automatic program 3 (11-color snap)
075 097 Automatic program 4 (11-color fade)
098 120 Automatic program 5 (4-color 4-zone step)
121 143 Automatic program 6 (11-color in-out snap)
144 166 Automatic program 7 (11-color in-out fade)
167 189 Automatic program 8 (rainbow fade)
190 212 Automatic program 9 (police)
213 235 Automatic program 10 (police 2)
236 255 Automatic program 11 (4-zone rainbow fade)
000 051 Preset dimmer speed from display menu
052 101 Dimmer speed mode off
102 152 Dimmer speed mode 1 (fast)
153 203 Dimmer speed mode 2 (medium)
204 255 Dimmer speed mode 3 (slow)
COLORband Q4 IP User Manual Rev. 2
Page 7 of 14
Page 10
Operation
4CH 7CH 10CH Function Value Percent/Setting
–11Dimmer 000 255 0–100%
122Red 000 255 0–100%
2 3 3 Green 000 255 0–100%
344Blue 000 255 0–100%
455Amber 000 255 0–100%
––6Color macros
–67Strobe
– – 8 Automatic programs
– – 9 Program speed 000 255 Automatic program speed, slow to fast
– 7 10 Dimmer speed mode
000 010 No function
011 255 Color macros
000 015 No function
016 255 Strobe, slow to fast
000 005 No function
006 028 Automatic program 1 (4-color snap)
029 051 Automatic program 2 (4-color fade)
052 074 Automatic program 3 (11-color snap)
075 097 Automatic program 4 (11-color fade)
098 120 Automatic program 5 (4-color 4-zone step)
121 143
144 166 Automatic program 7 (11-color in-out fade)
167 189 Automatic program 8 (rainbow fade)
190 212 Automatic program 9 (police)
213 235 Automatic program 10 (police 2)
236 255
000 051 Preset dimmer speed from display menu
052 101 Dimmer speed mode off
102 152 Dimmer speed mode 1 (fast)
153 203 Dimmer speed mode 2 (medium)
204 255 Dimmer speed mode 3 (slow)
Automatic program 6 (11-color in-out snap)
Automatic program 11 (4-zone rainbow fade)
Page 8 of 14
COLORband Q4 IP User Manual Rev. 2
Page 11
Operation
Configuration (Standalone)
Set the product in the standalone mode to control without a DMX controller.
Never connect a product that is operating in any standalone mode to a DMX string
connected to a DMX controller. Products in standalone mode may transmit DMX signals
that could interfere with the DMX signals from the controller.
Automatic Program
To run a program on the COLORband Q4 IP, follow the instructions below.
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select an automatic program, from P 1–11.
4. Press <ENTER>.
Auto Program Speed
To adjust the auto program speed on the COLORband Q4 IP, do the following:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> or <DOWN> to increase or decrease the program speed, from S. 1–100.
3. Press <ENTER>.
Static Color Mode
To run the COLORband Q4 IP on a static color, follow the instructions below.
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select a static color, from C 1–19.
4. Press <ENTER>.
Custom Color Mixing
To mix a custom color on the COLORband Q4 IP, do the following:
1. Press <MENU> repeatedly until u-- shows on the display.
2. Press <ENTER> and one of the following will show on the display:
• r. _ _ _ (red)
• G. _ _ _ (green)
• b. _ _ _ (blue)
• A. _ _ _ (amber)
3. Press <ENTER> to cycle through the options.
4. Use <UP> or <DOWN> to increase or decrease the selected value, from 0–255.
5. Repeat steps 3 and 4 until the color is set as desired.
Dimmer
To set the dimmer value on the COLORband Q4 IP, follow the instructions below.
1. Press <MENU> repeatedly until dIM shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to set the dimmer, from dIM1 (fast) to dIM3 (slow) or OFF.
4. Press <ENTER>.
Screen Lock
To lock/unlock the touchscreen on the COLORband Q4 IP, do the following:
1. Press <MENU> repeatedly until SEt shows on the display. Press <ENTER>.
2. Use <UP> or <DOWN> to select PASS. Press <ENTER>.
3. Use <UP> or <DOWN> to select on (activates password protection to lock screen) or oFF
(deactivates password protection to unlock screen).
4. Press <ENTER>.
Password: <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>
Factory Reset
To reset the COLORband Q4 IP to default factory settings, follow the instructions below:
1. Press <MENU> repeatedly until SEt shows on the display. Press <ENTER>.
2. Use <UP> or <DOWN> to select rESt. Press <ENTER>.
3. Use
4. Press <ENTER>.
COLORband Q4 IP User Manual Rev. 2
<UP>
or
<DOWN>
to select YES (resets product to factory default) or no (keep current settings).
Page 9 of 14
Page 12
Operation
Master/Slave Mode
The Master/Slave mode allows a single COLORband Q4 IP product (the “master”) to control the actions of
one or more COLORband Q4 IP products (the “slaves”) without the need of a DMX controller. The master
product will be set to operate in standalone, while the slave products will be set to operate in Slave mode.
Once set and connected, the slave products will operate in unison with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until
2. Press <ENTER>.
3. Set the DMX address to d. 1.
4. Connect the DMX input of the first slave product to the DMX output of the master product.
5. Connect the DMX input of the subsequent slave products to the DMX output of the previous slave
product.
6. Finish setting and connecting all the slave products.
Master product:
1. Press <MENU> repeatedly to go to the desired function or program.
2. Press <ENTER>.
3. Set the master product to operate in standalone.
4. Make the master product the first product in the DMX daisy chain.
• Configure all the slave products before connecting the master to the daisy chain.
• Never connect a DMX controller to a DMX string configured for Master/Slave operation
because the controller may interfere with the signals from the master.
• Do not connect more than 15 slaves to the master.
4Ch
shows on the display.
Page 10 of 14
COLORband Q4 IP User Manual Rev. 2
Page 13
Maintenance
5. Maintenance
Product Maintenance
Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of
the light source’s life and/or mechanical wear. To maintain optimum performance and minimize wear, clean
your lighting products at least twice a month. However, be aware that usage and environmental conditions
could be contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external
surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens-cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.
COLORband Q4 IP User Manual Rev. 2
Page 11 of 14
Page 14
Technical Specifications
UL 1573
CSA C22.2 No. 166
E113093
R
6. Technical Specifications
Dimensions and Weight
Length Width Height Weight
39.3 in (998 mm) 3.2 in (81 mm) 4.1 in (104 mm) 11.8 lb (5.35 kg)
Note: Dimensions in inches are rounded.
Power
Power Supply Type Range Voltage Selection
Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging
Parameter 120 V, 60 Hz 230 V, 50 Hz
Consumption 87 W 86 W
Operating current 1.18 A 0.67 A
Power-linking current (products) 11.2 A (9 products) 11.2 A (16 products)
Fuse T 3.15 A, 250 V T 3.15 A, 250 V
Power I/O U.S./Worldwide UK/Europe
Power input connector
Power output connector
Power cord plug
Light Source
Type Color Quantity Power Current Lifespan
LED
Quad-color
RGBA
Photometrics
Beam Angle Field Angle Illuminance @ 2 m
14° 27° 7,074 lux
Thermal
Maximum External Temperature Cooling System
104 °F (40 °C) Convection
DMX
I/O Connector Channel Range
3-pin XLR 4, 7, 10, 16, or 22 channels
Ordering
Product Name Item Code UPC Number
COLORband Q4 IP 10031864 781462222123
powerCON® TRUE1
powerCON® TRUE1
Edison
powerCON® TRUE1
powerCON® TRUE1
Bare wire
12 6 W 2.06 A 50,000 hours
Page 12 of 14
COLORband Q4 IP User Manual Rev. 2
Page 15
Returns
Returns
In case you need to get support or return a product:
• If you are located in the U.S., contact Chauvet World Headquarters.
• If you are located in the U.K. or Ireland, contact Chauvet Europe Ltd.
• If you are located in Benelux, contact Chauvet Europe BVBA.
• If you are located in France, contact Chauvet France.
• If you are located in Germany, contact Chauvet Germany.
• If you are located in Mexico, contact Chauvet Mexico.
• If you are located in any other country, DO NOT contact Chauvet. Instead, contact your local
distributor. See www.chauvetdj.com
France, Germany, or Mexico.
If you are located outside the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico,
contact your distributor of record and follow their instructions on how to return Chauvet
products to them. Visit our website www.chauvetdj.com
Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization
(RMA) number before shipping the product. Be prepared to provide the model number, serial number, and
a brief description of the cause for the return.
To submit a service request online, go to www.chauvetdj.com/service-request
Send the merchandise prepaid, in its original box, and with its original packing and accessories. Chauvet
will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product returned without an RMA
number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number directly
on the box.
for distributors outside the U.S., U.K., Ireland, Benelux,
for contact details.
.
Before sending the product, clearly write the following information on a piece of paper and place it inside
the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be
your responsibility. FedEx packing or double-boxing are recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).
COLORband Q4 IP User Manual Rev. 2
Page 13 of 14
Page 16
Contact Us
Chauvet World Headquarters
Chauvet Europe Ltd
Chauvet Europe BVBA
Chauvet France
Chauvet Germany
Chauvet Mexico
Address: Av. de las Partidas 34 - 3B
Lerma, Edo. de México, CP 52000
General Information Technical Support
Address: 5200 NW 108th Ave. Voice: (844) 393-7575
Sunrise, FL 33351 Fax: (954) 756-8015
Voice: (954) 577-4455 Email: chauvetcs@chauvetlighting.com
Fax: (954) 929-5560
Toll Free: (800) 762-1084 Website: www.chauvetdj.com
Address: Unit 1C Email: UKtech@chauvetlighting.eu
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK Website: www.chauvetdj.eu
NG16 6NT
Voice: +44 ( 0 ) 1 7 7 3 5 1111 5
Fax : + 4 4 ( 0 ) 1 773 511110
Address: Stokstraat 18 Email: BNLtech@chauvetlighting.eu
9770 Kruishoutem
Belgium Website: www.chauvetdj.eu
Voice: +32 9 388 93 97
Address: 3, Rue Ampère
91380 Chilly-Mazarin
France Website: www.chauvetdj.eu
Voice: +33 1 78 85 33 59
Address: Bruno-Bürgel-Str. 11
28759 Bremen
Germany Website: www.chauvetdj.eu
Voice: +49 421 62 60 20
(Entrance by Calle 2)
Zona Industrial Lerma Website: www.chauvetdj.mx
Voice: +52 (728) 690-2010
Email: FRtech@chauvetlighting.fr
Email: DEtech@chauvetlighting.de
Email: servicio@chauvet.com.mx
Contact Us
Visit the applicable website above to verify our contact information and instructions to request support.
Outside the U.S., U.K., Ireland, Mexico, France, Germany, or Benelux, contact the dealer of record.
Page 14 of 14
COLORband Q4 IP User Manual Rev. 2
Loading...