Champion UH-150B, UL-150 User Manual

Technical Manual

Undercounter Dishwasher

Model UH-150B

UH-150 UL-150

April, 2003

P.O. Box 4149 Champion Industries, Inc. Winston-Salem, North Carolina 27115-4149 www.championindustries.com

Manual P/N 0510172 REV. F

Machine Serial No.

Complete the information below so it will be available for quick reference.

Model Number __________________________ Serial Number ________________________ Voltage and Phase ______________________________________________________________ Champion Parts Distributor __________________________________ Phone _____________

(if applicable)

_____________________________________________________________________________

Champion Service Agency___________________________________ Phone _____________

_____________________________________________________________________________

Champion Industries Service: 1-800-858-4477 Champion Service Fax: 1-336-661-1660

NOTE: When calling to order parts, be sure to have the model number, serial number, voltage, and phase of your machine.

REVISIONS

Revision History

Revision Revised Serial Number Comments

Date Pages Effectivity

08/01/00 All W3245 Issue of manual and service replacement parts.

10/02/00 7 — Added dispenser priming instructions.

11/08/00 39 W3245 Deleted P/N 112204, replaced with P/N 109069.

01/17/01 17 — Changed Front panel P/N to 0308741.

08/21/01 21 — Revised hose clamp and hose part numbers.

02/05/03 39 –– Replaced 108391 with 113622 thermometer.

04/23/03 3,8,14,38,40,42,47 W7604 Inserted Final Rinse Sentry information.

04/23/03 19 –– Revised door hinge assemblies. Changed door catch

assembly from 0710162 to 0710161.

04/23/03 29,31 –– Changed hose P/N 0509214 to P/N 107417

THIS PAGE

INTENTIONALLY

LEFT BLANK

CONTENTS

Page

INTRODUCTION....................................................................................................................................... 1

WARRANTY.............................................................................................................................................. 2

GENERAL .................................................................................................................................................. 3

INSTALLATION........................................................................................................................................ 5

Unpacking ............................................................................................................................................ 5

Electrical Connections.......................................................................................................................... 5

Plumbing Connections ......................................................................................................................... 6

Detergent .............................................................................................................................................. 6

Rinse-Aid ............................................................................................................................................. 6

Chemical Sanitizer ............................................................................................................................... 6

Completing Installation........................................................................................................................ 7

OPERATION .............................................................................................................................................. 8

Operation Summary ............................................................................................................................. 8

Operation Procedures ........................................................................................................................... 8

Extended Wash Cycle .......................................................................................................................... 9

MAINTENANCE........................................................................................................................................ 10

Cleaning Schedule................................................................................................................................ 10

Deliming............................................................................................................................................... 11

Deliming Process.................................................................................................................................. 11

Maintenance Schedule.......................................................................................................................... 12

TROUBLESHOOTING .............................................................................................................................. 13

REPLACEMENT PARTS........................................................................................................................... 15

ELECTRICAL DIAGRAMS ...................................................................................................................... 42

TIMER CHARTS and DIAGRAMS........................................................................................................... 47

LIST OF FIGURES

Figure 1—Track and Panel Assembly......................................................................................................... 16

Figure 2—Door and Switch Assembly........................................................................................................ 18

Figure 3—Tank Heat and Drain.................................................................................................................. 20

Figure 4—Pump Assembly ......................................................................................................................... 22

Figure 5—Wash System Assembly............................................................................................................. 24

Figure 6—Water Inlet Piping ...................................................................................................................... 26

Figure 7—Fill System ................................................................................................................................. 28

Figure 8—Booster Assembly ...................................................................................................................... 30

CONTENTS

Figure 9—Detergent Pump Assembly....................................................................................................... 32

Figure 10—Sanitizer/Rinse-Aid Pump Assembly....................................................................................... 34

Figure 11—Drain Pump Assembly ............................................................................................................. 36

Figure 12—Control Cabinet........................................................................................................................ 38

Figure 13—Electrical Diagram, UH-150B After S/N W7604 .................................................................... 42

Figure 14—Electrical Diagram, UH-150B Prior to S/N W7604 ................................................................ 43

Figure 15—Electrical Diagram, UH-150 .................................................................................................... 44

Figure 16—Electrical Diagram, UL-150..................................................................................................... 45

Figure 17—Electrical Diagram, UH-150B (50Hz) ..................................................................................... 46

Figure 18—Timer Chart and Diagram, UH-150B After S/N W7604......................................................... 47

Figure 19—Timer Chart and Diagram, UH-150B, UH-150 Prior to S/N W7604 ...................................... 48

Figure 20—Timer Chart and Diagram, UL-150.......................................................................................... 49

INTRODUCTION

Welcome to Champion. Thank you for choosing Champion and for allowing us to take care of your dishwashing needs. This manual covers several models. Model numbers are shown on the front cover. Your machine has been completely assembled, inspected, and thoroughly tested at our factory

to eliminate problems at installation before it was shipped to your installation site. This manual provides:

•Warranty information

• Installation and operation procedures

• Maintenance instructions

•Troubleshooting guide

•Replacement parts lists.

Complete and return your warranty registration card as soon as possible. Champion constantly improves its products; therefore, specifications contained in this manual

may have changed. For your protection, factory authorized parts should always be used. Replacement parts may be ordered directly from Champion or from your Champion authorized

parts distributor or service agency. When ordering parts, supply the model number, serial number, voltage and phase of your machine, the part number, part description, and quantity.

Champion Industries Inc. (herein referred to as Champion), P.O. Box 4149, Winston-Salem, North Carolina 27115, and P.O. Box 301, 2674 N. Service road, Jordan Station, Canada, LOR 1S0, warrants machines, and parts, as set out below.

Warranty of Machines: Champion warrants all new machines of its manufacture bearing the name “Champion” and

installed within the United States and Canada to be free from defects in material and workmanship for a period of one (1) year after the date of installation or fifteen (15) months after the date of shipment by Champion, whichever occurs first. (See below for special provisions relating to glasswashers.) The warranty registration card must be returned to Champion within ten (10) days after installation. If warranty card is not returned to Champion within such period, the warranty will expire after one year from the date of shipment.

Champion will not assume any responsibility for extra costs for installation in any area where there are jurisdictional problems with local trades or unions.

If a defect in workmanship or material is found to exist within the warranty period, Champion, at its election, will either repair or replace the defective machine or accept return of the machine for full credit; provided, however, as to glasswashers, Champion’s obligation with respect to labor associated with any repairs shall end (a) 120 days after shipment, or (b) 90 days after installation, whichever occurs first. In the event that Champion elects to repair, the labor and work to be performed in connection with the warranty shall be done during regular working hours by a Champion authorized service technician. Defective parts become the property of Champion. Use of replacement parts not authorized by Champion will relieve Champion of all further liability in connection with its warranty. In no event will Champion’s warranty obligation exceed Champion’s charge for the machine. The following are not covered by Champion’s warranty:

a. Lighting of gas pilots or burners. b. Cleaning of gas lines. c. Replacement of fuses or resetting of overload breakers. d. Adjustment of thermostats. e. Adjustment of clutches. f. Opening or closing of utility supply valves or switching of electrical supply current. g. Cleaning of valves, strainers, screens, nozzles, or spray pipes. h. Performance of regular maintenance and cleaning as outlined in operator’s guide. i. Damages resulting from water conditions, accidents, alterations, improper use, abuse, tampering, improper

installation, or failure to follow maintenance and operation procedures.

j. Wear on Pulper cutter blocks, pulse vanes, and auger brush. Examples of the defects not covered by warranty include, but are not limited to: (1) Damage to the exterior or

interior finish as a result of the above, (2) Use with utility service other than that designated on the rating plate, (3) Improper connection to utility service, (4) Inadequate or excessive water pressure, (5) Corrosion from chemicals dispensed in excess of recommended concentrations, (6) Failure of electrical components due to connection of chemical dispensing equipment installed by others, (7) Leaks or damage resulting from such leaks caused by the installer, including those at machine table connections or by connection of chemical dispensing equipment installed by others, (8) Failure to comply with local building codes, (9) Damage caused by labor dispute.

Warranty of Parts: Champion warrants all new machine parts produced or authorized by Champion to be free from

defects in material and workmanship for a period of 90 days from date of invoice. If any defect in material and workmanship is found to exist within the warranty period Champion will replace the defective part without charge.

DISCLAIMER OF WARRANTIES AND LIMITATIONS OF LIABILITY.

CHAMPION’S WARRANTY IS ONLY TO THE EXTENT REFLECTED ABOVE. CHAMPION MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED, TO ANY WARRANTY OF MERCHANTABILITY, OR FITNESS OF PURPOSE. CHAMPION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THE REMEDIES SET OUT ABOVE ARE THE EXCLUSIVE REMEDIES FOR ANY DEFECTS FOUND TO EXIST IN CHAMPIOPN DISHWASHING MACINES AND CHAMPION PARTS, AND ALL OTHER REMEDIES ARE EXCLUDED, INCLUDING ANY LIABILITY FOR INCIDENTALS OR CONSEQUENTIAL DAMAGES.

Champion does not authorize any other person, including persons who deal in Champion dishwashing machines to change this warranty or create any other obligation in connection with Champion Dishwashing Machines.

WARRANTY

LIMITED WARRANTY

GENERAL

This manual covers the Champion undercounter dishwashing machine. This machine is fully automatic and is equipped with a 1/2 H.P. pump motor. All models are available for mounting directly to the floor or on optional stands (see accessories listed on page 4).

Standard equipment includes:

-Automatic tank fill -Upper and lower wash/rinse arms

-Common utility connections -Two dish racks (peg and flat)

-120 Volt control circuit -Exclusive vent design for

-Convenient, easy to use controls venting of condensation

-Door latch activated start switch -Stainless steel heavy-gauge construction,

-Detergent pump (UH-150, UH-150B) including base

-Detergent, rinse-aid & sanitizer pumps (UL-150) -Final rinse sentry (UH-150, UH-150B)

This series of dishwashers is available in the following models:

Model Numbers

UH-150B, UH-150, UL-150

• The UH-150B model is a high temperature (180°F/82°C rinse) sanitizing model with booster.

• The UH-150 model is a high temperature (180°F/82°C rinse) sanitizing model without booster.

• The UL-150 model is a low temperature (140°F/60°C rinse) sanitizing model for use with sodium hypochlorite solution (chlorine bleach) as a sanitizing agent. The rinse aid pump is standard.

Options

• Kit 504 - Top and side panels (P/N 0708756)

• Kit 505 - Top panel only (P/N 0708744)

• Kit 506 - Left side panel only (P/N 0708745)

• Kit 507 - Right side panel only (P/N 0708746)

• Kit 508 - Rinse aid pump kit (P/N 0708754)

• Kit 510 - Extended reach pumped drain kit (UH-150B, UH-150, UL-150) (P/N 0708766)

• Kit 511 - 70°F/39°C temperature rise booster (for 110°F/49°C supply water).

GENERAL

Accessories

• 17RS - 17" rack stand (raises working height and adds rack storage)

• 17T - 17" cabinet (raises working height and adds storage)

• CST - Combination sink/table (scraping and sorting station)

• 0501653 - Dish Rack (Peg Rack)

•0501654 - Silverware Rack (Flat Bottom Rack)

• 0710364 - 5" Base/Stand

Electrical Power Requirements

Booster Rated Minimum Supply Maximum Overcurrent Model Voltage Rise Amps Ckt. Ampacity Protective Device UL-150 115/60/1 N/A 13 15 15

UH-150 115/60/1 N/A 13 15 15 UH-150B 208/60/1 40 36 50 50 UH-150B 240/60/1 40 40 50 50 UH-150B 208/60/1 70 48 60 60 UH-150B 240/60/1 70 55 70 70

NOTE:

208-240V/60Hz/1PH electrical supply service must be a 3-wire plus ground for connection as shown for model UH-150B.

— 3-Wire Plus Ground Diagram

115V

208-240V 115V

L1 L2 N

00023

INSTALLATION

Unpacking

WARNING:

Care should be taken when lifting the machine to prevent damage.

1. Immediately after unpacking your machine, inspect for any shipping damage. If damage is found, save the packing material and contact the carrier immediately.

2. Remove the dishwasher from the skid. Adjust the feet if required, then move the machine to its permanent location.

3. Level the machine (if required) by placing a level on the top of the machine and adjusting the feet. Level the machine front-to-back and side-to-side.

CAUTION:

After locating your machine, it must meet local health codes. An example may be to seal your machine to the floor using a good grade of silicone sealant.

Electrical Connections

WARNING:

Electrical and grounding connections must comply with the National Electrical Code and/or Local Electrical Codes.

WARNING:

When working on the dishwasher, disconnect the electric service and tag it to indicate work is being done on that circuit.

1. The electrician should compare the electrical specifications on the machine electrical junction box (located behind the front panel) to the electrical power supply before connecting the machine to the incoming service at a fused disconnect switch.

NOTE:

The 208-240V/60Hz/1PH electrical supply service for model UH-150B must be a 3-wire plus ground service.

2. On the 208V-240V models, a knock-out is provided at the rear of the junction box (located behind the front panel) for electrical service connections. A fused disconnect switch or circuit breaker (supplied by user) is required to protect each power supply circuit.

3. On 115V models, your machine is already equipped with a 4-foot power cord and plug suitable for 115V-15A service.

!!!

INSTALLATION

Plumbing Connections

CAUTION:

Plumbing connections must comply with local sanitary and plumbing codes.

Water Connections

1. Connect the hot water supply (140°F/ 60°C Min) to the 1/2" I.D. fill hose. The fill solenoid valve is equipped with a flow control that will accept water pressures from 172 kPa/25 psi to 665 kPa/95 psi.

2. Install a manual shut-off valve in the water supply line to accommodate servicing the machine. The shut-off valve should be the same size or larger than the supply line.

3. The fill solenoid valve is equipped with a built-in strainer to protect from particles in the water supply.

Drain Connections

1. All Models are supplied with a flexible 5/8" I.D. drain hose, which must be connected to a 1-1/2" drain using a wye (Y) fitting.

Chemical Dispensing Pumps

1. Use a qualified detergent/chemical supplier for your detergent, rinse aid, and chemical sanitizer needs.

2. The cycle timer located in the main control cabinet is equipped with adjustable cams for the chemical dispensing pump(s). The cams control the length of time that the pumps operate. A qualified person may adjust the cam settings if necessary. Refer to the timer chart diagram(s) at the end of the manual for timer cam locations and factory time settings.

Detergents

1. Your machine is supplied with a detergent dispensing pump that is internally wired and ready for use. Using a liquid detergent, insert the labeled Detergent pickup tube into the detergent container. The pickup tube has a strainer on the end to prevent crystallized chemical from clogging the supply lines.

Rinse Aid

1. An optional rinse aid pump may be supplied for UH-150B and UH-150 models. Using a liquid rinse aid, insert the labeled Rinse Aid pickup tube into the rinse aid container.

Sanitizer

1. Model UL-150 is supplied with an internally wired chemical sanitizer dispensing pump. Using a sodium hypochlorite solution, insert the labeled Chemical Sanitizer pickup tube into the chemical sanitizer container.

2. Contact your chemical supplier for adjustment of the chemical sanitizer.

Floor

Max. Drain

Height

3 ft.

[915mm]

1-5/8"

[42mm]

1-1/2"

"Y"

Fitting

Do not connect to drain at 90°. Use "Y" fitting.

INSTALLATION

Priming Chemical Dispensing Pumps

1. Insert pick-up tubes in their respective chemical containers. Each pick-up tube is labeled to identify the proper container.

NOTE:

Make sure booster has been primed on Model UH-150B before priming chemical pumps.

2. For all models, push the DET/RINSE to prime the detergent and rinse-aid. Hold the switch, and observe fill chute on interior right side of machine until chemical enters the wash chamber.

3. For model UL-150 only, hold the SANITIZER switch in the up position to prime the sanitizer. Observe fill chute on interior right side of machine until you see chemical enter the wash tank.

Completing Installation

1. Remove any foreign material from inside the machine.

2. Center the scrap screen over the sump opening.

3. Prime the booster using the following procedure (if applicable).

CAUTION:

To prime the booster, the following procedure must be followed AFTER the electrical and plumbing connections have been made.

a. Close the front door. b. Remove the front panel. c. Locate the Installation and Service toggle switch on the extreme left side of

the control box.

d. Press the toggle switch down to the Booster Fill position and hold it

approximately 1 minute (or until water can be heard entering the machine). e. Release the toggle switch to stop the water flow. f. You have completed the booster priming process.

NOTE:

Push the Installation and Service toggle switch to the UP position.

Electrical power is now supplied to the machine.

WARNING:

Failure to prime the booster may cause damage to the booster elements and other electrical components and will void the warranty.

4. After plumbing and electrical connections are completed, check the machine for water leaks

by depressing the ON/FILL switch on the front panel, then close and latch the door. This allows the tank to fill and to complete the rinse cycle. Check for leaks.

5. Open the door and check the water level. The water level should barely cover the scrap screen.

6. Depress the OFF/DRAIN switch and close and latch the door to drain the tank. This allows the machine to complete the 100-second wash and drain cycle. Check the drain plumbing for leaks.

7. Replace the front panel. Installation is now complete.

!!!

OPERATION

Operation Summary

The following is a summary of your Undercounter Dishwashing Machine operating cycle:

1. The cycle begins when you depress the front edge of the door latch toward the door.

2. The green cycle lamp lights and the pump starts.

3. The pump runs during the wash cycle for approximately 80 seconds. The wash cycle duration is extended if booster is not up to temperature.

4. The pump stops, and the drain is opened.

5. After a 2-3 second pause, the pump drain cycle begins and continues for approximately 30 seconds.

6. After a 2-3 second pause, the fill valve opens, and the pump starts for the rinse cycle.

7. Within approximately 25 seconds, the rinse cycle is complete. The pump stops, the green cycle lamp turns off, and the cycle is complete.

8. Open the door and remove the rack of clean ware. The door must remain open for 5 seconds to allow the timer to reset before starting another cycle.

Operation Procedures

The operation of your dishwasher will be more efficient when these procedures are followed:

1. Check that the spray arms and scrap screen are in place.

2. Close the door and depress the front edge of the door latch toward the door. Push the ON/FILL switch to the ON position. The tank will begin filling with water. This procedure is followed only when the tank is empty.

3. When the tank is full, check the wash tank temperature gauge. Minimum wash temperatures are:

• UH-150B, UH-150 – 150°F/66°C.

• UL-150 – 140°F/60°C.

4. Scrap and preflush all items to be washed, and load the items into the rack. DO NOT OVERLOAD the rack. Wash only one layer of silverware in a rack.

5. Open the door and insert the rack into the machine.

6. Shut the door, and depress the door latch. This will start the wash cycle. The green cycle lamp located on the front control panel will light. This lamp will remain on until the entire wash and rinse cycle is completed.

OPERATION

NOTE:

The machine may be stopped at any time by opening the door. When restarted, the cycle does not start over. It will continue from the point at which it was interrupted.

7. Check the rinse temperature during the final rinse (120 seconds into cycle). The rinse temperature must be 180°F/82°C minimum for models UH-150B, UH-150, and 140°F/60°C for model UL-150.

8. The pump will automatically stop and the green cycle light will turn off indicating the cycle is completed.

9. Open the door and remove the rack.

10. Repeat steps 4-9 for additional cycles. Machine operation is automatic.

11. CLEAN the scrap screen after every meal period. During heavy usage, the scrap screen should be cleaned more frequently.

CAUTION:

Poor machine performance and/or damage to the machine can occur if the scrap screen becomes clogged with soil or waste particles.

12. After completing usage for the day, water in the tank should be drained by depressing the OFF/DRAIN switch and closing and latching the door. This initiates a 100-second wash and drain cycle that drains the tank.

CAUTION:

DO NOT LEAVE WATER IN THE TANK OVERNIGHT. Water left in the tank overnight will allow harmful chemicals to deteriorate the tank.

Extended Wash Cycle

On models UH-150B, UH-150, but not on model UL-150, an extended wash cycle is available for pots, pans and heavily soiled items.

To use the Extended Wash Cycle:

1. Insert the loaded rack into the machine. Close the door and depress the latch. Wait 10 seconds for the detergent to be dispensed automatically.

2. Flip the Extended Wash/Delime Switch to the UP position. The green cycle light will go out, indicating that the machine is in a continuous wash mode.

3. When your desired wash time has passed, flip the Extended Wash/Delime Switch to the DOWN position. The green cycle light will come on, indicating a return to the normal wash mode. The machine will now complete the remaining portion of the automatic cycle.

MAINTENANCE

The efficiency and life of your machine is increased by regularly scheduled preventive maintenance. A well maintained machine gives better results and service. An investment of a few minutes of daily maintenance will be worthwhile.

The best maintenance you can provide is to keep your machine clean. Components that are not regularly cleaned and flushed will clog and become inoperative.

Intervals shown in the following schedules represent an average length of time between necessary maintenance. Maintenance intervals should be shortened whenever your machine is faced with abnormal working conditions, hard water, or multiple shift operations.

Cleaning Schedule

• Daily – Every 8 Hours

1. Depress the OFF/DRAIN switch to OFF and close and latch the door to drain the tank.

2. Open the door and remove both the upper and lower spray arms by unscrewing the knurled fastener holding each spray arm.

3. Remove the scrap screen carefully to keep soil or waste particles from falling into the sump.

4. Clean inside the tank with clean water. Backflush the scrap screen until it is clean. Do not strike the screen against solid objects.

5. Clean the wash arms to remove any debris from spray openings. Do not strike the spray arms against solid objects.

6. Reinstall the scrap screen and spray arms.

7. Leave the door open overnight to allow drying.

8. Report any unusual conditions to your supervisor.

• Meal Periods

1. Clean the scrap screen after every meal period and more frequently during heavy usage. Do not allow the scrap screen to become clogged with soil or waste particles.

MAINTENANCE

Deliming

Your dishwasher should be delimed regularly as required. This will depend on the mineral content of your water.

Inspect your machine interior for lime deposits. If deliming is required, a deliming agent should be used for best results.

If you have the chemical sanitizing model (UL-150), carefully follow the following procedure before deliming:

DANGER:

Deliming solution or other acids must not come in contact with household bleach (sodium hypochlorite) or any chemicals containing chlorine, iodine, bromine, or fluorine. Mixing will cause hazardous gases to form. Skin contact with deliming solutions can cause severe irritation and possible chemical burns. Consult your chemical supplier for specific safety precautions.

1. Remove the sanitizer tube from the container. Place the tube into a container of hot water.

2. Depress and hold the SANITIZER prime switch (located on the front panel) until clear

water enters the tank through the fill air gap.

3. Close the door and depress the door latch. Complete two operating cycles to purge the

machine of all sanitizer.

Deliming Process

Complete the following procedure to delime your machine:

1. Add the delime chemical to wash the tank (per chemical supplier specifications).

2. Close and latch the door.

3. On models UH-150B and UH-150, depress the EXTENDED WASH/DELIME switch on

the front panel as soon as the cycle starts. On model UTL, proceed to step 5 of this procedure.

NOTE:

The EXTENDED wash/delime switch will operate only during the wash cycle. When this switch is in the ON position, the machine stays in the wash cycle until the switch is OFF. After switching to OFF, the machine will finish the cycle.

4. After 2-1/2 to 3 minutes (or as long as required), turn off the EXTENDED WASH/

DELIME switch. The machine will finish a complete cycle.

5. Complete two cycles with the machine empty to purge the machine of all delime chemicals.

6. Deliming is complete.

+ 39 hidden pages