64 Modular Series
64KB and 64KPRB Corner
Multiple Tank Rack Conveyor
Modular System
Shown with optional end panels
High Volume, Flexible Warewashing System
Champion’s prewash, wash, rinse and final rinse drive
modular units provide peak efficiency and maximum
design flexibility for your high volume application.
Exclusive Heavy-Duty Construction
The entire machine, including frame, base, legs, lower
panels and doors are heavy-gauge stainless steel for
durability and reliable service.
Simple, Fully Automatic Operation
Flip one switch to fill and heat the tanks and activate the
optional booster heater and blower-dryer. Then, one
pushbutton starts the conveyor and automatic operation.
Choice of Tank Heat
Standard electric elements or optional steam coils, or
steam injectors to maintain proper tank heat.
Space Saving Top Mounted Controls
Top mounted controls are convenient, safe and save
space. A reliable 120-volt control circuit allows easy
access for connecting chemical dispensing equipment.
Easy to Clean
Upper and lower spray arms are interchangeable and
have easily-removable end caps for fast, thorough
cleaning. Standard external scrap basket on the
prewash unit reduces soil build-up. The machine
continually cleans itself during operation, saving labor
and “down” time.
(3M) 1/99
CH033
64 Modular Series
64KB and 64KPRB Corner
Multiple Tank Rack Conveyor
Modular System
90° Application
Typical Modular Configurations
Modular Units
Prewash 22" A
Prewash 36" B
Corner Prewash 39" C
Corner Wash D
Corner Rinse E
Straight Wash F
Straight Rinse G
Wash/Rinse H
Final Rinse Drive J
*Shown on front of Spec Sheet
For electrical, drain, and
booster connections,
consult the Factory.
For Options and Accessories,
refer to 64KB and 64KPRB
Specification Sheets.
Note: Machine to be installed 6" (min.)
from wall.
Available in either right-to-left,
or left-to-right operation
Warning: Plumbing and electrical
connections should be made by qualified
workmen who will observe all the applicable
plumbing, sanitary, safety codes and the
National Electrical Code.
Note: Water Hammer Arrestor (meeting
ASSE-1010 standard or equivalent) to be
supplied (by others) in common water
supply line at service connection
®
Champion Industries, Inc., P. O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: 336/661-1979 • www.championindustries.com
®
Quick Facts
180° Application
Capacities
Racks per hr. (NSF rated) 201
Wash tank (gal.) 20
Conveyor speed (ft./min.) 7
Motor horsepower
Drive 1/4
Prewash 22", 36" and 37" 1
Wash 2
Rinse 2
Water consumption
Gal. per hr. (max. use) 300
Gal. per rack 1.49
Temperature °F
Wash 150
Rinse 160
Final Rinse 180
Heating
Tank heat, electric (Kw) 25
Tank heat, steam (lbs./hr.
required at 15 psi flow pressure) 125
Electric booster (built-in)
(Kw required for 40° rise) 36
Electric booster
(Kw required for 70° rise) 57
Steam booster
(lbs./hr. required for 40° rise) 185
Steam booster
(lbs./hr. required for 70° rise) 320
Venting
Load end (minimum cfm) 200
Unload end (minimum cfm) 400
Standard 20" x 20" rack complement
Peg 2
Flat 1
*Shown on front of Spec Sheet
Due to an ongoing value analysis program at
Champion, specifications contained in this
catalog are subject to change without notice.
Standard Features
Automatic tank fill
Common utility connections
Control circuit, 115-volt
Convenient top-mounted controls
Conveyor drive 1/4-Hp motor
Door activated drain closure
Door safety switch
Enclosure panel (front)
Energy sentinel (idle pump shut-off)
External scrap basket on prewash units
Interchangeable spray arms
Leakproof doors, internally fitted
Prewash 1-Hp pump motor
Low-water tank heat protection
Rinse saver device
Stainless steel heavy gauge construction,
including base and feet
Electric tank heat
(optional: steam coil or steam injectors)
Wash and rinse pumps with 2-Hp motors
64 Modular Series
64KB and 64KPRB Corner
Multiple Tank Rack Conveyor
Modular System
Sample configuration consisting of:
22" prewash, corner wash straight rinse,
final rinse drive, and optional end panels.
Standard external scrap
basket reduces soil build-up.
Champion Industries, Inc., P. O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: 336/661-1979 • www.championindustries.com
Racks are moved automatically by means of a 90° curved
pawl bar and conveyor.
Loading...