Chamberlain CPT4 Owner's Manual

Page 1

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

WARNING

Model CPT4

4-Channel Remote Control

OWNER'S MANUAL

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The Passport transmitter works with all LiftMaster Security✚® rolling code garage door openers.

When using the Passport transmitter with an access system or gated entry, contact property manager.

If it is necessary to program a HomeLink

transmitter for an

access system, contact property manager.

PROGRAMMING

LOCK

LIGHT

1. Press and hold the button on the hand-held remote* that you wish to operate your garage door.

2. While holding the remote button, press and hold the light button on the Multi-Function Door Control.

3. Continue holding both buttons while you press the push bar on the Multi-Function Door Control (all three buttons are held).

4. Release buttons when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

2 3

1. Press and release the “learn” button on the motor unit. The learn indicator light will glow steadily for 30 seconds.

2. Within 30 seconds, press and hold the button on the hand-held remote* that you wish to operate your garage door.

3. Release the button when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

USING THE “LEARN” BUTTON

LOCK

LIGHT

LOCK

LIGHT

USING THE MULTI-FUNCTION DOOR CONTROL

To Erase All Codes From Motor Unit

Memory

To deactivate any unwanted remote, first erase all codes:

Press and the hold “learn” button on motor unit until the learn indicator light goes out (approximately 6 seconds). All previous codes are now erased. Reprogram each remote or keyless entry you wish to use.

NOTE: The fourth button is recommended for use with a garage door opener and cannot be used with an access system. Use buttons 1 through 3 for the access system or other garage door openers.

GARAGE DOOR

OPENER

ACCESS SYSTEM OR GARAGE DOOR OPENERS

For more information, please visit www.devancocanada.com or call toll free at 855-931-3334

Page 2

WARNING

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor. To reduce risk of fire, explosion or chemical burn:

• Replace ONLY with 3V2032 coin batteries.

• DO NOT recharge, disassemble, heat above 100°C (212°F) or incinerate.

The Remote Control Batteries

1. The lithium batteries should produce power for up to 5 years.

2. To replace, pry open case with visor clip or screwdriver, as shown. Insert batteries positive side up (+). See figure 4.

3. Dispose of old batteries properly.

FOR SERVICE DIAL OUR TOLL FREE NUMBER:

1-800-582-2806

Replacement Parts

Model CPT4 remote case. . . . . . . . . . . . . . . . K74-17929

(circuit board not included)

3V2032 Lithium battery (2 required). . . . . . . . . . . 10A20

Visor clip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29B137

Figure 4

HOW TO ORDER REPAIR PARTS

DEVANCO CANADA

19192 HAY ROAD, UNIT Q

SUMMERSTOWN, ON K0C 2E0

TOLL FREE: 855-931-3334

www.devancocanada.com

WHEN ORDERING REPAIR PARTS

PLEASE SUPPLY THE FOLLOWING INFORMATION:

3 PART NUMBER 3 DESCRIPTION 3 MODEL NUMBER