CLICKER
MODEL CLT1D
Universal Garage Door Opener Remote Control
The Clicker remote can be programmed to operate up to 2 garage door openers or gates, including different brands. All programming is done using the:
•Brand Switches
•Remote Control DIP Switches
•Remote Control Push Buttons, A and B, and LED Indicator
|
|
LED |
|
Button A |
Button B |
BRAND Switches |
ON |
BRAND |
UP position is ON |
|
|
|
Switches |
|
DOWN position is OFF |
|
|
|
DIP |
|
|
|
|
|
|
Switches |
DIP Switches |
ON |
Battery |
|
||
|
|
|
UP position is ON |
|
|
DOWN position is OFF |
|
|
|
|
Slide Battery |
NOTE: Use pen or small screwdriver |
cover down |
|
to move dip switches. |
|
to remove |
WARNING
•Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
•ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.
Motor Unit
& Receiver
External Ceiling or
Wall Mounted Receiver DIP Switches or
Smart-Learn Button
Remote
Control
1PREPARATION
Determine the BRAND ID of the existing garage door opener or handheld remote controls. If all remote controls are lost, the BRAND ID is located on the ceiling mounted motor unit or on the external receiver near the flexible wire antenna.
Also, determine if your motor unit/receiver system has DIP SWITCHES or a SMART-LEARN BUTTON. Some models require removing the light lens. For further information, consult your garage door opener manual.
Proceed to the appropriate section for your type of opener.
4PROGRAMMING THE PUSH BUTTON
Press and hold both buttons until LED begins to flash. When LED flashes, release both buttons and immediately press the button that you want to activate the door and release.
Your clicker is now programmed, proceed to step 5 or 6.
• For Chamberlain, Sears, LiftMaster and Master Mechanic if your garage door opener has a Smart-Learn button, continue on to step 5.
• For all other types continue to step 6.
2 |
SET BRAND SWITCH |
5 |
SMART-LEARN BUTTON PROGRAMMING |
|
|
A. Press and release Smart-Learn button.
B. Press and hold button selected in step 4 for 3 seconds.
|
|
|
|
|
NOTE: If you have a Chamberlain, Sears, Liftmaster, Master |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mechanic or Do It motor unit/receiver with a Yellow, White or Gray |
|
|
|
|
|
|
|
Smart-Learn button, it will activate immediately upon successful |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
programming. If your motor unit/receiver has a Green, Orange, Red |
|
|
|
|
|
|
|
or Purple Smart-Learn button, the light bulb will blink signifying it has |
|
|
|
|
|
|
|
learned the Clicker remote control code. |
1 |
2 |
3 |
|
KG |
KG |
Proceed to step 3.
6PROGRAMMING IS COMPLETE
Programming is complete. To test, press the button selected to activate garage door.
NOTE: For Genie, Stanley, Linear and Moore-O-Matic if programming does not work, review brand and dip settings and repeat steps 4 through 6. Also, try reversing the dip switch settings (Turn ON to OFF and OFF to ON). Brand code switches remain the same.
NOTE: If programming to more than one motor unit; after successfully programming button “A,” determine the brand of the second garage door opener. Follow the instructions pertaining to that particular brand to program button “B.” Programming a different code into button “B” will not affect button “A.” The codes and brand switch settings are retained within their specific Clicker button.
Proceed to step 4.
3SET THE DIP SWITCHES
Open existing remote to expose code switches or obtain the switch settings from your receiver.
Match the Clicker’s DIP switches to already existing receiver/remote DIP switches. Set extra DIP switches in the Clicker remote to the off position.
NOTE: For Chamberlain, Sears, LiftMaster and Master Mechanic, if the receiver/remote DIP switch has three positions labeled “+,” “0” and “-," do not use the “0” position.
If you have a three button remote, #1 switch must be set to “-” if you would like the large button to open the door.
Existing |
Clicker |
remote |
remote |
Match existing DIP switches. Remaining switches are off.
REMOTE CONTROL BATTERY
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
TECHNICAL SUPPORT
|
©2006, Clicker |
114A3272B |
All Rights |