C. Crane CC WiFi Instruction Manual

INSTRUCTION MANUAL

PLEASE READ ALL THE INSTRUCTIONS

COMPLETELY BEFORE USE AND SAVE THIS

MANUAL FOR FUTURE REFERENCE

v1.0

Internet Radio

CC WiFi

Before Use

Please read IMPORTANT SAFETY INSTRUCTIONS before use. It
is important to read and understand all instructions. Keep these
precautions and instructions where all who use this radio will read
them.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK DO

NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE THE RADIO BACK. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

THE LIGHTNING FLASH AND ARROWHEAD WITHIN
THE TRIANGLE IS A WARNING SIGN ALERTING YOU
OF “DANGEROUS VOLTAGE” INSIDE THE RADIO.

THE EXCLAMATION POINT WITHIN THE TRIANGLE IS
A WARNING SIGN ALERTING YOU OF IMPORTANT
INSTRUCTIONS ACCOMPANYING THIS RADIO.

The box should contain the CC WiFi Radio, AC Adapter and this man ual.
If anything is missing or damaged, please contact your dealer immediately.
We recommend you keep the box in the unlikely event your radio needs to
be serviced.

2 CC WIFI

CC WIFI 3

Table of Contents

Unpacking .............................................................................................................

2

Location of Controls ............................................................................................

4-5

Getting Started

Turning the Radio On ......................................................................................

6

Scanning for Wireless Networks ...................................................................

6

Connecting to a Wireless Network ................................................................

7

Entering Your WEP or WPA Key ....................................................................

8

Connecting to Network Using Ethernet Cable .............................................

10

Choosing a Radio Station ...................................................................................

11

Changing the Volume ..........................................................................................

12

Menu Time Out .....................................................................................................

13

Setting the Time and Date ...................................................................................

13

Setting the Alarm .................................................................................................

14

Setting the Sleep Timer .......................................................................................

16

Configure Menu Options .....................................................................................

17

Help Pages ...........................................................................................................

19-23

Safety Instructions ..............................................................................................

24

Location of CC WiFi Radio Serial Number ........................................................

25

Location of Controls — Front and Back of Radio

Location of Controls — Front and Back of Radio

Q

LCD Display

W

PLAY/PAUSE/STOP or
PRESET #1

E

PREVIOUS or PRESET #2

R

NEXT or PRESET #3

T

Remote Sensor

Q

W

E

R

T

Y

U

I

O

P

Y

DIAL/VOLUME/SELECT

U

REPLY

I

BACK

O

POWER ON/OFF

P

Speaker

{

DC Power Jack

} Line Out Jack

{

}

q

w

q

Headphone Jack

w

Ethernet Jack

4 CC WIFI

CC WIFI 5

Location of Controls — Remote Control

e

POWER: Switch radio
ON/OFF

r

1-9: Store presets and recall
functions

t

MUTE: Mute the audio

y

REPLY: Used for Pandora,
Aupeo! and adding stations
to Reciva

u

STORE: Store up to 99
radio stations

i

--/-: Used for presets 10 and
above

o

RECALL: Play pre-set
stations

p

+ or - VOL: Adjust volume

[

PLAY/PAUSE: Play or pause
track

]

STOP: Stop track play. Press
and hold to delete a track
from the playlist

A

NEXT: Play next track

S

BROWSE: View tracks in
playlist

D

UP/DOWN: Scroll through
options

F

SELECT: Select a displayed
option

G

MODE: Switch between
Repeat and Shuffle modes

H

PREV: Play previous track

J

BACK: Reverts back to the
previous menu or option

e

t

u

y

i

r

S

A

p

[

F

G

H

J

D

o

]

Buttons 23-26 and 29-30 are used only in Media Player
mode while playing tracks from your computer.

Location of Controls — Remote Control

Getting Started – Turning On Your WiFi Radio

6 CC WIFI

Getting Started – Turning On Your WiFi Radio

Note: Configuring a WiFi radio is similar to navigating through a cell
phone menu.

Plug the power adapter cube into a 120V AC power outlet. Connect
the power adapters small plug into the jack on the back of the radio
that is labeled “DC IN 7.5V”.

Caution: Use only the power adapter supplied with the radio.
Connecting a power adapter other than the one that was sup­plied with your radio could cause permanent damage to the
radio and may be hazardous.

After a few seconds the display on the front of the radio will light up
and show:

Followed by:

CC WiFi Radio

Reciva Enabled

ARM Powered

Followed by:

Followed by:

Initialising

Network

Starting ...

< Scan for Networks >

Enter Network

and

Scanning for Wireless Networks

When <Scan for Networks> is displayed, press “SELECT” by press­ing “in” the main dial (the main dial should click when pressed in).

The display will show:

CC WIFI 7

Scanning for Wireless Networks

Scanning for Wireless Networks

Connecting to a Wireless Network

Scanning

No networks

found

When the radio finds wireless networks, it will show the network
names (also called the ESSID) in the display screen.

Note: You can always use the BACK button to start over at the previ­ous screen.

The first two wireless networks will show in the display after the wire­less network scan. There may be more wireless networks to choose
from by further rotating the dial.

If the radio cannot find any wireless networks, then the display will
show:

If no networks are found, see page 33 for troubleshooting assistance.

Example:

< WiFi Network 1 >

WiFi Network 2

Example:

< WiFi Network 2 >

Your Network

To connect to your wireless network, align your network name
between the brackets and select it by pushing the dial in.

19

8 CC WIFI

Connecting to a Wireless Network

Connecting to a Wireless Network

Entering Your WEP or WPA Key (Wireless Password)

END <> A BCDE

Need Help?: Refer to help page 33 for help finding your WEP or
WPA Key.

After a few seconds the display will go into a password entry mode.
This mode contains upper case letters, lower case letters, numbers,
and special characters.

Notice that the letter “A” is separated from the other characters in the
center of the display. Rotate the dial and you will see how the center
character is always separated from the other characters. Continue
rotating the dial until the first character of your WEP or WPA password
is in the center of the display. Select it by pressing the main dial in.

However, if the screen displays:

Enter WEP Key

Enter WPA Key

or

you must enter the correct WEP or WPA wireless encryption key
(Wireless Password) to proceed.

Note: Take note which type of key your network requires for future
reference.

If the display
shows:

then continue
on to page 12.

Connecting to

Network

After you have selected the first character of your password, it will
appear below.

ABCDE F GHIJ

_

19

CC WIFI 9

Entering Your WEP or WPA Key (Wireless Password)

Entering Your WEP or WPA Key (Wireless Password)

ABCDE F GHIJ

F _

Turn the dial to the next character in the password and SELECT.
Repeat this process until your entire wireless password is entered on
the lower line.

XYZab c defg

Frank12abc _

Note: WEP passwords use numbers 0-9 and upper case letters A-F.
WPA passwords are case sensitive to upper and lower case letters,
so you must enter them exactly.

Example:

After the final character is entered, turn the dial until “END” shows in
the middle of the display — press the dial to select.

()“ END ghA

Connecting to

Network

The display will show “Connecting to network” as the radio connects
to the WiFi network.

Connecting to

“My Network”

and

Then:

Station Update

From Reciva

Your networkʼs name will be displayed here.

Need Help?: Refer to help pages 33-39 for troubleshooting connec-
tion problems.

When finished, the radio automatically goes to the “Primary Menu”
that contains six options: STATIONS, PERSONAL RADIO,
MY STUFF, MEDIA PLAYER, CONFIGURE and ALARM CLOCK.

19-23

10 CC WIFI

< Stations >

Personal Radio

Entering Your WEP or WPA Key (Wireless Password)

Note: Menu tree flow charts are located on pages 40-42.
To begin choosing stations skip to “Choosing a Radio Station” on

page 11.

Connecting to a Network Using Ethernet Cable (optional)

After the radio successfully connects to your router it will automatically
go to the “Primary Menu” that contains six options: STATIONS,
PERSONAL RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and
ALARM CLOCK.

Need Help?: Refer to help page 37 for troubleshooting connection
problems.

Note: Menu tree flow charts are located on pages 40-42.

2. Connect the opposite end of the Ethernet cable to the Ethernet
port on the back of your radio.

3. Plug in the power cord to the radio.

After a few seconds, the connection light will flash indicating a good
connection.

< Stations >

Personal Radio

Entering Your WEP or WPA Key (Wireless Password)

When using an ethernet cable to connect, little setup is required.

1. While the radio is unplugged from power, connect a standard Cat5
or Cat6 Ethernet cable (not included with radio)
to an open LAN port on your router. The LAN
ports are the ones typically numbered 1-4 on
the back of your router.

Note: Ethernet cables can be purchased from
C. Crane Company or your local electronics store.

Note: Menu tree flow charts are located on pages 40-42.
To begin choosing stations skip to “Choosing a Radio Station” on

page 11.

Connecting to a Network Using Ethernet Cable (optional)

23

CC WIFI 11

Choosing a Radio Station

1. From the Primary Menu, choose “My Stuff” by turning the dial
until brackets are positioned on both sides. Press the dial to select.

< Stations >

Personal Radio

My Stuff

Media Player

< Stations >

Personal Radio

My MP3tunes

My Live365

Note: The “My Streams” menu lets you choose between the
following stations: Russian Christian Radio (RadioMv.com) or
English Christian Radio Station (RadioMv.Org).

2. Next, turn the dial to choose from either the “My Streams” or “My
MP3tunes” menu. Press the dial to continue into the selected menu.

Note: The “My MP3tunes” menu lets you choose from audiofiles
available, such as Audio Bible, Talk Shows and Audiobooks under
"Artist" and "Album" headline.

"MP3tunes" is on demand playback option of audio files from
RadioMv.com & RadioMv.org

12 CC WIFI

Changing the Volume

Changing the Volume

You can change the volume by turning the dial clockwise to increase
the volume and counterclockwise to decrease the volume. The display
shows the volume bar. You cannot change the volume when you are
in a menu, except when using the remote control. After a station is
selected and begins to play, you can then change the volume with the
main dial.

Store a Radio Station as a Preset

A. Using the Controls on the Front of the Radio to Play

Presets 1-3.

While a radio station is playing, press and hold one of the preset
buttons for three seconds or until the display screen shows
“Assigned to Preset”.

B. Using the Remote Control to Store Presets 1-9.

While a radio station is playing, press and hold the preset number
on the remote control that you want the station to be stored to.
After three seconds the display screen will show “Assigned to
Preset”.

C. Using the Remote Control to Store Presets 10-99.

While a radio station is playing, press the STORE button, then the

-/-- button, and then enter your desired preset number. The display
screen will show “Assigned to Preset”.

Play a Stored Radio Station Preset

A. Using the Controls on the Front of the Radio to Play

Presets 1-3.

Briefly press and release the preset button assigned to the station
you want.

B. Using the Remote Control to Recall Presets 1-9.

Briefly press and release the preset button assigned to the station
you want.

C. Using the Remote Control to Recall Presets 10-99.

Briefly press the RECALL button, then the --/- button, and then
enter your desired preset number 10-99.

CC WIFI 13

Menu Time-Out

Menu Time-Out

When a radio station is playing — if BACK or SELECT is pressed, the
radio will go into menu selection mode. If no radio controls are used
within ten seconds, the radio will “time-out” and go back to the cur­rently playing radio station.

Setting the Time and Date

Note: At any point, you can use the BACK button to start over at the
previous screen.

1. If you are currently listening to a radio station, briefly press the dial
once to access the Primary Menu. You can also access the
Primary Menu by pressing and holding the BACK button.

The Primary Menu contains six options: STATIONS, PERSONAL
RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and ALARM
CLOCK.

2. Turn the main dial until “Configure” shows in brackets — press the
dial to select.

Media Player

< Configure >

3. Turn the dial clockwise to “Clock Setup” — press the dial to select.

Register

< Clock Setup >

< Set Time/Date >

Clock Format

4. Turn the dial to “Set Time/Date” — press the dial to select..

5. Turn the dial until the hour setting is correct — press the dial to
select.

6. Turn the dial until the minute setting is correct — press the dial to
select.

14 CC WIFI

Setting the Time and Date

Setting the Time and Date

Set Time

12:00 AM

7. Turn the dial until the day of the month is correct — press the dial
to select. Follow the same method for setting the month and year.

8. When finished, the radio will show “Time and Date Set”.

Set Date

01 Jan 2008

Time and Date

Set

Setting the Alarm

3. Turn the dial until “Set Alarms” shows in brackets — press the dial

to select.

< Set Alarms >

Sleep Timer

Note: At any point, you can use the BACK button to start over at the
previous screen.

1. If you are currently listening to a radio station, briefly press the dial
once to access the Primary Menu. You can also access the
Primary Menu by pressing and holding the BACK button.

The Primary Menu contains six options: STATIONS, PERSONAL
RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and ALARM
CLOCK.

2. Turn the main dial clockwise until “Alarm Clock” shows in brackets
— press the dial to select.

Configure

< Alarm Clock >

CC WIFI 15

Setting the Alarm

Setting the Alarm

4. Turn the dial and choose one of the five alarm slots to set — press
the dial to select.

Disable All

< 1 OFF >

7. Choose how frequently you want the alarm to sound. Choose
between “Once”, “Every Day”, “Weekly”, “Week Days”, and
“Weekends” — press the dial to select.

Note: If “Once” or “Weekly” is selected, you will also be prompted to
select the day of the week that you would like the alarm to sound.

< Once >

Every Day

5. Turn the dial until the hour setting is correct — press the dial to
select.

6. Turn the dial until the minute setting is correct — press the dial to
select.

Set Alarm
12:00 AM

8. Choose whether to sound the alarm as a buzzer or a preset radio
station — press the dial to select.

Note: If you do not have any radio stations stored as presets, then
“Buzzer” will be your only option.

9. When the setup is finished, the display will show “Alarm Set”.

< Buzzer >

Preset Station

Alarm Set

16 CC WIFI

Setting the Sleep Timer

Setting the Sleep Timer

With the sleep timer enabled, the internet radio will automatically
switch itself off after a set amount of time.

Note: At any point, you can use the BACK button to start over at the
previous screen.

1. If you are currently listening to a radio station, briefly press the dial
once to access the Primary Menu. You can also access the
Primary Menu by pressing and holding the BACK button.

The Primary Menu contains six options: STATIONS, PERSONAL
RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and ALARM
CLOCK.

2. Turn the main dial clockwise until “Alarm Clock” shows in brackets
— press the dial to select.

3. Turn the dial until “Sleep Timer” shows in brackets — press the
dial to select.

4. The radio will show “Sleep Timeout” and the amount of time before
the radio turns off. By default the sleep timer is turned off.

Set Alarms

< Sleep Timer >

Sleep Timeout

< Off >

Configure

< Alarm Clock >

Turn the dial to increase the amount of time before the radio turns
itself off. 15 minute increments are used. Press the dial to select.

Sleep Timeout

< 00:15 >

“Timer Set” will show in the display
indicating that the radio will play for
the selected amount of time before
switching itself off.

Timer Set

CC WIFI 17

Media Player Functions

SONAL RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and
ALARM CLOCK.

2. Turn the main dial clockwise until “Media Player” shows in
brackets — press the dial to select.

3. Turn the dial clockwise until “Playback Mode” shows — press the
dial to select.

4. Turn the dial clockwise until “Repeat” shows — press the dial to
select.

Configure Menu Options

Media Player Functions

SONAL RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and
ALARM CLOCK.

2. Turn the main dial clockwise until “Media Player” shows in
brackets — press the dial to select.

3. Turn the dial clockwise until “Playback Mode” shows — press the
dial to select.

4. Turn the dial clockwise until “Repeat” shows — press the dial to
select.

Configure Menu Options

To access the “Configure” menu follow these steps:

1. Briefly press the dial once to access the Primary Menu. You can
also access the Primary Menu by pressing and holding the BACK
button.

The Primary Menu contains six options: STATIONS, PERSONAL
RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and ALARM
CLOCK.

2. Turn the main dial until “Configure” shows in brackets — press the
dial to select. Turn the dial clockwise to access all the options.

<Network Config>

This option is used for configuring your radioʼs network settings, net­work parameters, and scanning for wireless networks. Once the radio
has established a connection to the network, the information will be
saved to the radio for later use.

<Version>

Displays the electronic serial number and other information pertaining
to software and hardware installed on your internet radio.

<Upgrade Firmware>

Use this option to download new control programing for the radio. If

there is new firmware available when this option is selected, then the
radio will prompt you to download.

Note: A firmware upgrade may take several minutes. DO NOT TURN
OFF THE POWER TO YOUR RADIO WHEN UPGRADING FIRM-

Configure Menu Options

<Language>

Allows you to change the display language.

WARE. If the firmware upgrade is interrupted, your radio may endure
permanent damage. A firmware upgrade may take several minutes to
finish.

<Factory Reset>

This option puts all settings back to their default, as they were when
the radio left the factory. If you perform a factory reset on your radio,
you will lose all your presets, clock settings, and wireless network
connection settings.

18 CC WIFI

Media Player Functions

SONAL RADIO, MY STUFF, MEDIA PLAYER, CONFIGURE and
ALARM CLOCK.

2. Turn the main dial clockwise until “Media Player” shows in
brackets — press the dial to select.

3. Turn the dial clockwise until “Playback Mode” shows — press the
dial to select.

4. Turn the dial clockwise until “Repeat” shows — press the dial to
select.

Configure Menu Options

Configure Menu Options

<Language>

Allows you to change the display language.

WARE. If the firmware upgrade is interrupted, your radio may endure
permanent damage. A firmware upgrade may take several minutes to
finish.

<Factory Reset>

This option puts all settings back to their default, as they were when
the radio left the factory. If you perform a factory reset on your radio,
you will lose all your presets, clock settings, and wireless network
connection settings.

<Register>

This option will display a key that can be used to register the radio on
the Reciva Customer Portal.

<Backlight>

Selecting this option will alter the Internet radioʼs backlight values.

1. After selecting the “Backlight” menu item, the radio will show three
backlight adjustment modes: “Inactive”, “Active”, and “Standby”.
These three settings are explained below:

a) The “active” state is when the user is pressing buttons or

turning knobs.

b) The radio goes into its “inactive” state when there is no

user activity for 30 seconds.

c)

“Standby” is the state when the radio has been turned off.

2. Rotate the dial to select the desired backlight mode — press the
dial to select.

3. The radio will display the current backlight value for the selected
mode. You can change this value by turning the dial to increase or
decrease it.

<Clock Set Up>

Use this option to set the time, date and clock format. See “Setting
the Time and Date” on page 15.

<UPNP>

Use this option to set a name for your radio that can be recognized by

Configure Menu Options

<WiFi Strength>

This option will give you your current WiFi signal strength between the
radio and the router. Our experience shows that a signal strength of
20 to 30% is required for good reception.

the UPNP Server.

RadioMv Stream Network.

13-16.

CC WIFI 19

Help Pages — Wireless Network Help

Help Pages — Wireless Network Help

“No Networks Found” shows after scanning for wireless net­works:

1. Sometimes your wireless network will not show on the first scan.
Try scanning for networks again on your radio.

2. Check the LED lights on the front of your wireless router. Be sure
that the “power” and “wireless” LED lights are on. If they are not
on, you may need to call the manufacturer of the router for more
assistance.

3. Your radio may be out of range of your wireless network. Place the
radio closer to your router as a test, then scan for wireless net­works again. The CC WiFi Radio may not have the same WiFi
range as a new WiFi enabled laptop.

4. There is a setting on your WiFi router called “Enable SSID
Broadcast”. This must be enabled. You may need to call the manu­facturer of the router for more assistance.

About Your WEP or WPA Encryption Key: This is also called a
“Wireless Network Password” and is used to keep unwanted “guests”
from using your wireless network. If you are unaware of what your
password is, you can follow our suggested steps for finding it:

1. Search your records for a document that was printed out after the
setup of your router. This document should contain the WEP Key
or WPA Passphrase. If your router was setup by someone else,
they should have provided you with a document that contained the
needed information.

2. If you are using a wireless router that was provided by your Inter­net Service Provider, the WEP or WPA key will sometimes be

About Your Network Name (SSID): This is the name which was
assigned to your wireless router by the person who set it up. After
scanning for your wireless network, rotate the dial through all of the
results because you may recognize your network name (SSID). If your
routerʼs manufacture name is displayed, try selecting it (e.g., “Linksys”
or “Netgear”). If your wireless network has not been renamed from the
default factory name, then it most likely does not require a wireless
encryption key (WEP or WPA) password to connect.

20 CC WIFI

Help Pages — Wireless Network Help

Help Pages — Wireless Network Help

printed on the bottom of the router.

3. If all else fails, try calling the manufacturer of your wireless router
for assistance with locating the routers wireless encryption key.

Having Trouble Connecting to a Wireless Network: This problem
can be caused by a number of possible scenarios.

1. Check your WEP or WPA wireless encryption key — it may be
wrong. If you don't know your WEP or WPA encryption key, refer to
the section above titled “About Your WEP or WPA Encryption Key.

2. WEP keys should be entered using uppercase letters A-F and
numbers 0-9. WEP keys are easy to spot because they use
either 10 total characters or 26 total characters. When entering a
WPA key you must enter it exactly as entered in your routerʼs
settings, including upper and lower case letters.

3. After scanning for wireless networks, turn the dial through all the
possible choices. You may recognize your network as another
name.

4. Check your routerʼs compatibility with the WiFi radio. The radio is
not compatible with wireless “N” technology, also called 802.11N. If
using “N” technology only, then change your routerʼs settings to
use wireless “B” and/or “G” technology also. It may be necessary
to call the manufacturer of your router for help making these
changes.

5. Be sure that your internet is working. Try accessing the internet
using a computer that is connected to the same router as the
radio. If you cannot access the internet on your computer, the
radio will not connect either. It may be necessary to call your inter­net service provider for help repairing your internet connection.

CC WIFI 21

Help Pages — Error Message Troubleshooting

Timeout Getting IP Address:

1. An incorrect WEP or WPA key may have been entered into the
radio. This is the most common reason for this error. Check your
router to make sure your wireless encryption key is correct or see
page 33-34 for more help with finding your encryption key. A good
troubleshooting test is to temporarily try connecting to your router
with encryption disabled.

2. Your radio may be too far away from the wireless router. Try mov­ing it closer or use the ethernet cable.

3. Wireless router is not DHCP enabled. Consult your routerʼs user
manual for enabling DHCP or contact the manufacturer of the
router for more assistance.

4. Your router may be using an unknown encryption type. Try a differ­ent type of encryption on your router. One good troubleshooting
test is to temporarily disable your routerʼs encryption and see if the
radio connects to it.

5. Your router may be set up to use “Wireless N” only. In this case,
change the routerʼs wireless settings to use “Wireless B and G
Mixed” or “Wireless B, G, and N Mixed”. For more information
about how to configure your routerʼs settings, consult your routerʼs
user manual or call the routerʼs manufacturer for more assistance.

6. There may be too much interference from nearby wireless devices.
Move the radio away from laptops or other wireless devices.

2.4gHz telephones and baby monitors can cause interference,
if placed near the radio.

7. You may be attempting to connect to an ad-hoc type network. If
you are attempting to connect to a network that is not yours, it may
be configured for ad-hoc (computer-to-computer) and may not
have internet. To check what network type you are connecting to,
use your computer to scan for available networks. On the list of
available networks you should be able to see if the network is
infrastructure type (good) or ad-hoc (bad).

Port 80 Connect Failed. Unable to Load Station List:

Your radio is unable to connect to Reciva using the internet.

1. Your internet connection may not be working. Check the internet
using a computer that is connected to the same router.

Help Pages — Error Message Troubleshooting

19 -20

22 CC WIFI

Help Pages — Error Message Troubleshooting

Help Pages — Error Message Troubleshooting

Timeout Connecting to Reciva Gateway.
Check Firewall Port 5000:

Your router is not letting the radio connect to Reciva using the UPNP
service.

1. UPNP may be disabled on your router. UPNP must be enabled for
the radio to work correctly. Consult your routerʼs user manual for
enabling UPNP or contact the manufacturer of the router for more
assistance.

2. Your router or modem may be temporarily confused even though
your computer is working fine. Try unplugging the power from both
the router and modem for two minutes. First, power the modem
(giving it time to startup), then power the router (also giving it time
to startup). Last, power your radio and try connecting again.

3. Your internet provider may be blocking UPNP (port 5000) from
being used by their customers. This is very uncommon but some
satellite internet companies, colleges, and businesses block this
port for an extra layer of network security. To find out if this port is
being blocked, speak with your internet service provider or system
administrator.

4. Your router may not offer the UPNP setting. In this case, manually
open port 4999-5001 and assign these open ports to an IP
address that is a little higher than your computerʼs. (Example: If
your computerʼs IP address is 192.168.1.5, assign the open ports
to 192.168.1.9.) On your radio, select “CONFIGURE”, then select
“NETWORK CONFIG”, then select “EDIT CONFIG”. When the
message displays “Auto DHCP Yes or No” select “NO”. From this
point, enter the new IP address that has the open ports assigned
to it, along with other network information.

2. UPNP may be disabled on your router. UPNP must be enabled for
the radio to work correctly. Consult your routerʼs user manual for
enabling UPNP or contact the manufacturer of the router for more
assistance.

3. Your router or modem may be temporarily confused even though
your computer is working fine. Try unplugging the power from both
the router and modem for two minutes. First, power the modem
(giving it time to startup), then power the router (also giving it time
to startup). Last, power your radio and try connecting again.

CC WIFI 23

Help Pages — Error Message Troubleshooting

Help Pages — Ethernet Network Help

The LED Connection Light Does Not Flash When Cable is
Inserted into Radio:

1. Be sure that the power is connected to both the radio and the
router.

2. Your Ethernet cable may be damaged or incompatible. Use a
“Straight Through” Cat5 or Cat6 Ethernet Cable. You can purchase
Ethernet cables from C. Crane or your local electronics store.

Having Trouble Connecting to a Network using an Ethernet
Cable:

1. The CC WiFi Radio may be set to use “Wireless Only”. By default,
the radio is set to “Auto” and can connect to either a wireless net­work or an Ethernet network. To change this setting navigate to:
CONFIGURE > NETWORK CONFIG > WIRED/WIRELESS. For
an ethernet cable connection, set to “Auto” or “Wired Only”.

2. Be sure that your internet is working. Try accessing the internet
using a computer that is connected to the same router as the
radio. If you cannot access the internet on your computer, the
radio will not connect either. It may be necessary to call your inter­net service provider for help repairing your internet connection.

3. It may be necessary to configure your radio with a “static” IP
address if your router is not setup to use DHCP. To manually con­figure the radioʼs network settings, navigate on your radio to: CON­FIGURE > NETWORK CONFIG > EDIT CONFIG. Contact your
network administrator to acquire the proper network addresses.

24 CC WIFI

Safety Instructions

To prevent damage to your radio or possible injury to you or others, read
these safety precautions and instructions entirely before applying power
to your radio. Keep these precautions and instructions where all who use
this radio will read them.

1) COMMON CARE !

Check the radio, AC adapter and any accessories regularly. Do not use
the radio if there is any sign of damage. Only operate in accordance
with the instructions in this manual. Only use attachments or acces­sories specified by the manufacturer.

2) DISCONNECT THE RADIO IN CASE OF MALFUNCTION !

If you smell or notice smoke, disconnect the AC Adapter immediately,
taking care to avoid burns. Contact C. Crane Company or their repre­sentative for inspection and service before any future operation. Only
use the AC-DC Adapter recommended with the unit and replace it if
wires become frayed or exposed. It should have an output of three
Volts DC with the center negative, and not less than 150 MAh. Use
only the recommended adapter. Otherwise it may damage the radio or
cause a fire or electric shock.

3) KEEP OUT OF REACH OF CHILDREN !

Dropping the radio can cause damage or injury. Keep the AC Adapter
cord in a position so someone cannot trip and cause the radio to fall.

4) KEEP AWAY FROM WATER AND MOISTURE !

Keep the radio dry. Liquids and moisture can damage the radio. If a liq­uid leaks into the radio do not operate and seek a qualified service
shop. To clean the radio, remove the power and use a damp cloth on
the exterior only.

5) KEEP AWAY FROM EXTREME TEMPERATURES !

Extreme temperatures can damage the radio. Do not leave or use the
radio where it can be subjected to high or very cold temperatures.

6) DO NOT ATTEMPT TO SERVICE RADIO !

Refer all service work to a qualified service shop when the radio does
not appear to operate normally, exhibits a change in performance or
the radio has received damage. Never open the radio as this may
expose you to dangerous voltages and this will void all warranties.

7) OUTSIDE ANTENNAS OR CABLES !

Outside antennas or cables that create a potential hazard should not
be used with this radio unless installed by qualified personnel.

READ BEFORE

OPERATING EQUIPMENT

SAVE THESE INSTRUCTIONS

" !

CC WIFI 25

This product contains software licensed under version 2 of the GNU public
license and version 2.1 of the GNU Lesser Public License. The source code
for this software is available from:
http://www.reciva.com/gpl/

This product includes technology owned by Microsoft Corporation and under
a license from Microsoft Licensing GP. Use or distribution of such technology
outside of this product is prohibited without a license from Microsoft
Corporation and/or Microsoft Licensing, GP as applicable.

Model: CC Wifi
ANSI C63.4: 2003
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERA­TION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS.

1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.

Notice: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority
to operate the equipment.

Location of Your CC WiFi Radio Serial Number

From the “Primary Menu” of the CC WiFi Radio, follow this path to
find your serial number: CONFIGURE > VERSION > SERIAL
NUMBER.

Record your serial number here for future reference:

Location of Your CC WiFi Radio Serial Number

From the “Primary Menu” of the CC WiFi Radio, follow this path to
find your serial number: CONFIGURE > VERSION > SERIAL
NUMBER.

Record your serial number here for future reference: