Casio TI-310 User Manual

USE ONLY WITH ADAPTOR
MODEL M/N-75

RINGS

TS

4

2

TONE

PULSE

RING VOL.

OFF

HI

LO

IMPORTANT

SAFETY INSTRUCTIONS

INSTALLATION INSTRUCTIONS

1. Never install telephone wiring during a lightning storm.

2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the
network interface.

4. Use caution when installing or modifying telephone lines.

SAFETY PRECAUTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.

4. Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool.

5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage
to the product.

6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by
placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near
or over a radiator or heat register. This product should not be placed in an enclosed environment unless
proper ventilation is provided.

7. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by
animals or persons walking on it.

8. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.

9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the
product.

10.To reduce the risk of electric shock, do not disassemble this product. Take it to a qualified serviceperson when
service or repair work is required. Opening or removing covers may expose you to dangerous voltages or
other risks. Incorrect re-assembly can cause electric shock when the appliance is subsequently used.

11.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only those controls

that are covered by the operating instructions because improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to restore the product to normal

operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.

12.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of
electric shock from lightning.

13.Do not use the telephone to report a gas leak while near the leak.

SAVE THESE INSTRUCTIONS

REMOTE OPERATION

I

Remote operation allows you to access the TI-310
from any cellular or touch-tone phone. The 3-digit

Remote Access Code is printed on the bottom of
the unit. To enable remote operation, you may

need to press and hold each remote access
number for 2 seconds. If you intend to call from
rotary or pulse telephones, order the Touchtone
Dialer on the ACCESSORY page.

LISTENING TO

MESSAGES

(OPTION 1)

After the access code has been entered,
messages will automatically be played.

1

PAUSING MESSAGES

During playback of the message you want
paused, press

1

Messages will be paused for up to one
minute before disconnecting. To resume
playback, press

1

on your keypad.

1

again.

ERASE MESSAGES

(OPTION 2)

During playback of the message you want
erased, press

1

To confirm deletion of the message, you
will hear a beep.

To erase all messages, press 2 after
hearing “

2

hear a beep and all messages will be
erased.

2

on your touchtone keypad.

End of Messages.

” You will

CHANGE YOUR

GREETING

(OPTION 3)

If your TI-310 is currently playing back
messages, press

1

pause playback.

Press 3 on your telephone keypad, a
beep will be heard, begin recording your

2

new greeting.

Press

3

on your telephone keypad when

finished speaking. Your new greeting

3

will play automatically.

NOTE:

■ There is a one minute maximum for recording your
greeting through remote operation.

1

on your keypad to

SKIP BACKWARD

(OPTION 4)

Press

4

on your keypad to skip back to

the previous message.

1

REPEAT MESSAGE

(OPTION 5)

Press

5

on your keypad to repeat the

current message.

1

SKIP FORWARD

(OPTION 6)

Press

6

on you keypad to skip forward

to the next message.

1

REMOTE ANSWER

OFF/ON

(OPTION 7 & 8)

Press

8

on your keypad after hearing

“

End of messages

1

answering machine off. Upon exiting
remote operation, the unit will be turned
off and no further messages will be
recorded.

In the event you accidentally turned your
answering machine off, press

2

keypad to turn the unit back on.

.” to turn the

7

on your

EXITING REMOTE

OPERATION

(OPTION 9)

Press

9

on your keypad at any time

during remote operation to exit.

1

MESSAGE RETRIEVAL

WHEN MEMORY

IS FULL

If the TI-310’s memory is full, you will hear three
short beeps followed by, “
messages remotely when the TI-310’s memory is
full:

Enter your
as the greeting plays.

1

After listening to messages, you may
press

2

2

on the keypad to erase all

messages and allow callers to leave new
messages.

Memory full.

3-DIGIT ACCESS CODE

” To retrieve

J

Recorded messages are cut off.

The TI-310 is designed to disconnect from the
line after a caller stops talking. Calls may be cut
off if a 5 second pause is detected, if the caller
does not speak loud enough or if a message is
less than two seconds.

The TI-310 does not respond when you enter
your remote access code while the greeting is
playing

Try re-entering the correct code after the beep.
Press each number of the access code for at
least two seconds.

Between messages there is an operator
recording or a beep and dial tone.

The caller has hung up without leaving a
message. A shorter greeting will reduce the
frequency of these recordings.

You have more than one telephone number
and are experiencing difficulty.

See MULTI-LINE INSTALLATION.

There is no sound during playback.

Check and adjust the

The unit does not automatically stop playing
the greeting or recording a message when an
extension phone is picked up.

Briefly press and release the
the extension phone.

The unit is not responding when keys are
pressed.

The TI-310 has approximately a 5 second
initialization process. Once the unit is plugged
in, the unit requires 5 seconds in which it runs
its internal diagnostic tests. The MESSAGES
INDICATOR will flash when the unit is ready for
operation.

VOLUME

.

HOOK-SWITCH

TROUBLESHOOTING

After recording a new greeting from remote
operation, the unit does not respond.

HERE’S HOW TO REACH US

By Phone:
HELPLINE: [phone], Monday - Friday,

8 a.m. to 4:45 p.m., PST

AUTHORIZED FACTORY SERVICE CENTER:

Phone Masters Repair Center
[phone], Monday - Friday,
8 a.m. to 5 p.m., PST

PARTS ORDERS USING A CREDIT CARD:

Pacific Coast Parts Distributors, Inc.
[phone] or [phone],
Monday - Friday, 8 a.m. to 4:30 p.m., PST

On-line:
CUSTOMER RELATIONS:

WEBSITE: www.casiocomm.com
E-MAIL: [e-mail]

AUTHORIZED FACTORY SERVICE CENTER:

WEBSITE: www.members.home.net/

skelly1/PM1.htm

E-MAIL: [e-mail]

PARTS AND ACCESSORIES:

WEBSITE: www.pacparts.com
E-MAIL: [e-mail]

AUTHORIZED FACTORY SERVICE CENTER
For repairs, please bring or send your unit to:
Phone Masters Repair Center
11899 Valley View Street
Garden Grove, CA 92845

1. Pack your product securely in a sturdy
shipping box.

2. Include a clear and specific explanation of
the problem.

3. Include your name, street address (sorry,
no P.O. box), and daytime phone number.

4. Provide a legible photocopy of the dated
store receipt for one-year warranty
purposes.

Register on-line at www.casiocomm.com

or fill-out and return the enclosed

on

After you record your new greeting, you must
press 3 again on your keypad to end the
recording. If 3 is not pressed, the unit will
suspend remote operation access for 13
minutes. You will be able to retrieve your
messages after the 13 minutes.

A greeting was recorded but the default
greeting plays.

Check the length of the recorded greeting. In
order for the TI-310 to accept a greeting, it must
be at least two seconds in length or the unit will
default to the pre-recorded greeting.

After several attempts the TI-310 will not
operate properly.

To reset the TI-310, unplug the

PLUG

from the back of the TI-310 for 10
seconds and remove the battery (if one is
installed). The greeting, incoming messages
and time/day stamp will be lost. Re-record the
greetings and set the time and day.

Design and specifications are subject to

change without notice.

CASIO COMMUNICATIONS, INC.

20665 Manhattan Place

Torrance, CA 90501-1827

Internet Website:

http://www.casiocomm.com

M2S1 3/00

Printed in Malaysia

AC ADAPTER

QUESTIONS?

product registration card.

K

EASY TO USE

OWNER'S GUIDE

TI-310

Telephone with
Digital Answering Machine

Turn over for

installation

instructions

FCC REQUIREMENTS

USER INSTRUCTIONS

1. This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment is a label
that contains, among other information, the FCC registration number and Ringer Equivalence
Number (REN) for this equipment. If requested, provide this information to your telephone company.

2. The REN is useful to determine the quantity of devices you may connect to your telephone line and
still have all of those devices ring when your number is called. In most, but not all areas, the sum of
the RENs of all devices should not exceed five (5.0). To be certain of the number of devices you may
connect to your line, as determined by the REN, you should call your local telephone company to
determine the maximum REN for your calling area.

3. If your answering machine causes harm to the telephone network, the telephone company may
discontinue your service temporarily. If possible, they will notify you in advance. But if advance
notice is not practical, you will be notified as soon as possible. You will be advised of your right to
file a complaint with the FCC.

4. Your telephone company may make changes in its facilities, equipment, operations, or procedures
that could affect the proper operation of your equipment. If they do, you will be given advance notice
so as to give you an opportunity to maintain uninterrupted service.

5. If there is a problem with this unit, the telephone company may ask you to disconnect this
equipment from the network until the problem has been corrected or you are sure that the
equipment is not malfunctioning.

6. Repairs can only be made by the manufacturer or an authorized service agency. Unauthorized
repairs void registration and warranty. Contact seller or manufacturer for details of permissible user­performed routine repairs, and where and how to have other than routine repairs made.

7. This equipment may not be used on coin service provided by the telephone company. Connection to
party lines is subject to state tariffs. (Contact your state public utility commission or corporation
commission for information.)

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

● Consult the dealer or an experienced radio/TV technician for help.

Any changes made by the user not approved by CASIO COMMUNICATIONS can void the user’s
authority to operate the equipment. This product is hearing aid compatible.

Jack: RJ11 Ringer Equivalence: See bottom/underside of the TI-310 base unit.

CASIO COMMUNICATIONS, Inc. 20665 Manhattan Place, Torrance, CA 90501

REFERENCIA RÁPIDA

L

CONEXIÓN DEL TI-310

ENCHUFE

TI-310 en un enchufe de pared de

1

teléfono.

CONECTE

de CA en el tomacorriente para

2

adaptador de CA que hay en la parte
de atrás del TI-310.
cordón a través del sujetador de
cordón del adaptador de CA para
evitar una desconexión accidental.

NOTA:

■ La desconexión del adaptador de CA de
la parte de atrás de la unidad hará que la
TI-310 borre todos los mensajes
recibidos, mensajes de salida, números
de marcación automática, hora y fecha.

ENCHUFE

auricular en el auricular y en el lado

3

izquierdo del TI-310.

ENCHUFE

tomacorriente de pared eléctrico.

4

Después de la señal acústica, los
indicadores luminosos destellarán.
Una vez que los indicadores
luminosos comiencen a destellar, se
puede grabar un mensaje de salida.

INSTALE

(9V) para proteger los mensajes de

5

salida, los mensajes recibidos y las
configuraciones de hora y día.
Durante un corte de suministro
eléctrico, esta información se guarda
hasta que la batería se agote.

el cordón de teléfono del

el enchufe del adaptador

ENGANCHE

el cordón extensible del

el adaptador de CA en un

una batería de 9 voltios

Grabe un mensaje de salida personalizado de
hasta 1 minuto de duración para responder a las
llamadas.

1

el

NOTA:

■ El nivel de sonido se ajusta automáticamente cuando el

3

NOTA:

■ Si la memoria del TI-310 está llena, reproduzca y

GRABACIÓN DE

MENSAJES DE SALIDA

Asegúrese de que los indicadores
luminosos están encendidos o
destellando. El mensaje de salida debe
ser de

más de dos segundos o la unidad
utilizará el mensaje de salida
predeterminado.

Fije el control de volumen
en un nivel que usted pueda oír.

2

mensaje de salida se transmite por la línea de teléfono.

Oprima el botón de grabación de
mensaje de salida

RECORD)

indicador de grabación

INDICATOR)

borre todos los mensajes antes de grabar su
mensaje de salida

Comience a hablar a aproximadamente
7 plg del micrófono.

4

Cuando termine de hablar, oprima el
botón de grabación de mensaje de

5

salida
nuevamente para dejar de grabar. Si no
oprime el botón de grabación de
mensaje de salida

RECORD)

automáticamente de grabar pasado un
minuto.

La TI-310 reproducirá automáticamente
el mensaje de salida.

6

y espere que se encienda el

. Oirá una señal acústica.

(GREETING RECORD)

, la unidad dejará

(VOLUME)

(GREETING

(RECORD

(GREETING

M

The TI-310 can easily be wall mounted by following these instructions. If you have a standard
telephone wall mounting bracket, begin with step 2.

NOTE:

■ Purchase wood screws, round head, brass, size #10, 1 1/4 inches in length.

1
2

3
4

5

6

7

WALL MOUNTING

Mount screws into wall. Use the
template (right) to space screws
correctly.

Guide the telephone cord through the
right cord holder on the unit’s
bottom.

Tightly coil the telephone cord
around the four guides on the in-side
of the wall mounting bracket.

Pull the telephone cord through the
center opening on the wall mounting
bracket.

Guide the AC Adapter through the left
cord holder on the bottom of the
unit.

Tightly coil the AC Adapter cord
around the four guides on the in­side of the wall mounting bracket.

Direct the AC Adapter cord through
the opening in the side of the wall
mounting bracket.

Snap the wall mounting bracket into
the back of the TI-310.

8

Plug the AC Adapter into a wall outlet
and the telephone cord into a wall

9

jack.

Remove the handset retainer clip

10

located above the speaker grill in
the handset cradle and rotate the
clip 180 degrees. Replace the
clip. This secures the handset.

T

E

M

P

L

A

T

E

N

This limited warranty gives you specific legal rights; you may also have other rights which vary from state to state.
The limited warranty is extended only to the original consumer of a CASIO COMMUNICATIONS product and is valid
only with respect to consumers within the United States of America and Canada. Should this product prove defective by
reason of improper workmanship or material during the period of one (1) year from the date of original purchase,
CASIO COMMUNICATIONS will repair or, at its option, replace the product without charge for parts or labor. If CASIO
COMMUNICATIONS elects to replace the product, such replacement may be accomplished with a factory-reconditioned
unit. This limited warranty does not apply: (a) to any product damaged by accident, misuse, improper line voltage,
lightning, fire, water, or other acts of nature, (b) if the product is altered or repaired by anyone other than CASIO
COMMUNICATIONS, INC. or one of its authorized warranty stations or (c) if the FCC-approved connector plugs are
removed. This limited warranty does not cover broken or marred cabinets.
Except to the extent prohibited by applicable law, all implied warranties made by CASIO COMMUNICATIONS in
connection with this product are limited in duration to a period of one (1) year from the date of original purchase, and
no warranties, whether expressed or implied, shall apply to this product after said period.
Should this product prove defective in workmanship or material, the consumer’s sole remedies shall be such repair or
replacement as is herein-above provided. Under no circumstances shall CASIO COMMUNICATIONS be liable for any
loss or damage, direct, consequential, or incidental arising out of the use of or inability to use this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusion may not apply to you.
In order to obtain warranty service, you must provide evidence of purchase date. For your convenience, keep the
dealer’s dated bill of sale or delivery ticket as evidence of the purchase date. See Troubleshooting section above for
details. Before returning or exchanging your product, call the CASIO COMMUNICATIONS Helpline at [phone].

To order accessories for your TI-310, simply cut out this order form, fill in the appropriate information
and send it with payment (check, money order or credit card information) to:
Pacific Coast Parts Distributors, Inc., 15024 Staff Court, Gardena, CA 90248. For parts orders using a
credit card: [phone] or [phone], Monday - Friday, 8 a.m. to 4:30 p.m., PST.
To order on-line: www.pacparts.com E-MAIL: [e-mail]

Description Part No. Price Qty. Total
Lightning Arrestor - Recommended for areas prone to electrical storms. 2700140 $19.95
AC Adapter - For Model TI-310. 1601086 $13.50
Touchtone Dialer - Activates the beeperless remote operation. 2001018 $19.95

Please charge my credit card.

Name ______________________________________________________________________________
Street Address_______________________________________________________________________
City _________________________________________ State __________ Zip Code _______________
Signature___________________________________________ Telephone_______________________
We do not accept C.O.D. orders. Allow 15 working days for delivery. Prices subject to change without

notice. Returns subject to 20% restocking charge upon approval.

LIMITED WARRANTY

IMPORTANT! SALES SLIP OR EVIDENCE OF PURCHASE DATE REQUIRED

ACCESSORIES

Enclosed is my check/money order for the total amount.

CA residents add applicable sales tax

VISA MasterCard

Card No.

Expiration Date

All orders add shipping and handling $3.50

Subtotal

Total

O

P

4336-920-0-01

Install a 9 volt (9V) battery to protect your greeting, incoming messages and time/day setting during
power failure. During a power failure, this information is saved until the battery is depleted.

Turn the TI-310 over and remove the battery cover. Install a 9V alkaline battery. Make sure the
battery is connected correctly. Replace the cover.

1

INSTALLATION

PLUG

the TI-310’s telephone cord

into a telephone wall jack.

2

CONNECT

the back of the TI-310.

3

Cord Holder to prevent accidental disconnection.

NOTE:

■ Disconnection of the AC Adapter from the back of the unit will cause the TI-310
to erase all recorded messages, greetings, autodial numbers, the time and
date.

the AC Adapter Plug into the AC Adapter Outlet on

LOOP

the cord through the AC Adapter

PLUG

the coiled handset cord into the

handset and into the left side of the TI-310.

4

PLUG

the AC Adapter into an electrical wall

outlet. After the beep the LEDs will flash.

5

Once the LEDs start flashing, you may record
your greeting.

A