Casio PAW2000-1CR Operation Manual

MO1007-EC

Operation Guide 3172

Congratulations upon your selection of this CASIO watch.

Applications

The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude. Measured values are then shown on the display. Such features make this watch useful when hiking, mountain climbing, or when engaging in other such outdoor activities.

• The measurement functions built into this watch are not intended for taking measurements that

require professional or industrial precision. Values produced by this watch should be considered as reasonable representations only.

• When engaging in mountain climbing or other activities in which losing your way can create a

dangerous or life-threatening situation, always use a second compass to conﬁ rm direction readings.

• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss

suffered by you or any third party arising through the use of this product or its malfunction.

Warning !

About This Manual

• Button operations are indicated using the letters shown in the

illustration.

• Note that the product illustrations in this manual are intended for

reference only, and so the actual product may appear somewhat different than depicted by an illustration.

(Light)(Light)

Things to check before using the watch

1. Check the battery power level.

Is “H” or “M” displayed for the battery power indicator?

NO YES

Does any one of the following conditions exist?

• Battery power indicator shows “L” and “

upper left corner of the screen.

• “C” is displayed in the lower left corner of the screen.

• The face is blank.

Power is low.

where it is exposed to light. For details, see “Charging the Watch”.

Charge the watch by placing it in a location

YES

LOW

” is displayed in the

Battery power indicator

The watch is charged sufficiently. For details about charging, see “Charging the Watch”.

Go to step 2.

2. Check the Home City and the daylight saving time (DST) setting.

Use the procedure under “To conﬁ gure Home City settings” to conﬁ gure your Home City and daylight saving time settings.

Important!

Proper time calibration signal reception, and World Time Mode and Sunrise/Sunset Mode data depend on correct Home City, time, and date settings in the Timekeeping Mode. Make sure you conﬁ gure these settings correctly.

3. Set the current time.

• To set the time using a time calibration signal

See “To get ready for a receive operation”.

• To set the time manually

See “Conﬁ guring Current Time and Date Settings Manually”.

The watch is now ready for use.

• For details about the watch’s radio controlled timekeeping feature, see “Radio Controlled Atomic

Timekeeping”.

Charging the Watch

The face of the watch is a solar cell that generates power from light. The generated power charges a built-in rechargeable battery, which powers watch operations. The watch charges whenever it is exposed to light.

Charging Guide

Whenever you are not wearing the watch, leave it in a location where it is exposed to light.

• Best charging performance is

achieved by exposing the watch to the strongest light available.

Warning! Leaving the watch in bright light for charging can cause it to become quite hot. Take care when handling the watch to avoid burn injury. The watch can become particularly hot when exposed to the following conditions for long periods.

• On the dashboard of a car parked in direct sunlight

• Too close to an incandescent lamp

• Under direct sunlight

Important!

• Allowing the watch to become very hot can cause its liquid crystal display to black out. The

appearance of the LCD should become normal again when the watch returns to a lower temperature.

• Turn on the watch’s Power Saving function and keep it in an area normally exposed to bright light when

storing it for long periods. This helps to ensure that power does not run down.

• Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is

blocked from exposure to light can cause power to run down. Expose the watch to bright light whenever possible.

When wearing the watch, make sure that its face is not blocked from light by the sleeve of your clothing.

• The watch may enter a sleep state

if its face is blocked by your sleeve even only partially.

Power Levels

You can get an idea of the watch’s power level by observing the battery power indicator on the display.

Level Battery Power Indicator Function Status

(H)

(M)

Battery power

Battery power indicator

indicator

• The ﬂ ashing

bright light for charging is required as soon as possible.

• At Level 5, all functions are disabled and settings return to their initial factory defaults. Once the battery

reaches Level 2 (M) after falling to Level 5, reconﬁ gure the current time, date, and other settings.

• Display indicators reappear as soon as the battery is charged from Level 5 to Level 2 (M).

• Leaving the watch exposed to direct sunlight or some other very strong light source can cause the

battery power indicator to show a reading temporarily that is higher than the actual battery level. The correct battery level should be indicated after a few minutes.

• All data stored in memory is deleted, and the current time and all other settings return to their initial

factory defaults whenever battery power drops to Level 5 and when you have the battery replaced.

Power Recovery Mode

• Performing multiple sensor, illumination, or beeper operations during a short period may cause all of

the battery power indicators (H,M, and L) to start ﬂ ashing on the display. This indicates that the watch is in the power recovery mode. Illumination, alarm, countdown timer alarm, hourly time signal, and sensor operations will be disabled until battery power recovers.

• Battery power will recover in about 15 minutes. At this time, the battery power indicators (H,M,L) will

stop ﬂ ashing. This indicates that the functions listed above are enabled again.

• If all of the battery power indicators (H,M,L) are ﬂ ashing and the C (charge) indicator also is ﬂ ashing,

it means the battery level is very low. Expose the watch to bright light as soon as possible.

• Even if battery power is at Level 1 (H) or Level 2 (M), the Digital Compass Mode, Barometer/

Thermometer Mode, or Altimeter Mode sensor may be disabled if there is not enough voltage available to power it sufﬁ ciently. This is indicated when all of the battery power indicators (H,M,L) are ﬂ ashing.

• Frequent ﬂ ashing of all of the battery power indicators (H,M,L) probably means that remaining battery

power is low. Leave the watch in bright light to allow it to charge.

LOW

indicator at Level 3 (L) tells you that battery power is very low, and that exposure to

(L)

(C)

5 All functions disabled.

All functions enabled.

Auto and manual receive, illumination,

beeper, and sensor operation disabled.

Except for timekeeping and the C (charge) indicator, all functions and display indicators disabled.

Charging Times

Daily

Exposure Level (Brightness)

Outdoor sunlight (50,000 lux) 5 min. 2 hours 11 hours 3 hours

Sunlight through a window (10,000 lux)

Daylight through a window on a cloudy day (5,000 lux)

Indoor ﬂ uorescent lighting (500 lux) 8 hours 87 hours – – – – – –

*1 Approximate amount of exposure time required each day to generate enough power for normal daily

operation.

*2 Approximate amount of exposure time (in hours) required to take power from one level to the next.

• The above exposure times all are for reference only. Actual exposure times depend on lighting

conditions.

• For details about the operating time and daily operating conditions, see the “Power Supply” section of

the Speciﬁ cations.

Power Saving

When turned on, Power Saving enters a sleep state automatically whenever the watch is left for a certain period in an area where it is dark. The table below shows how watch functions are affected by Power Saving.

• There actually are two sleep state levels: “display sleep” and “function sleep”.

Elapsed Time in Dark Display Operation

60 to 70 minutes (display sleep) Blank, with PS ﬂ ashing Display is off, but all functions are enabled.

6 or 7 days (function sleep) Blank, with PS not ﬂ ashing

• The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch is already in a sleep

state when 6:00 AM arrives, however, it will remain in the sleep state.

• The watch will not enter a sleep state while it is in the Stopwatch Mode or Countdown Timer Mode.

To recover from the sleep state

Move the watch to a well-lit area, press any button, or angle the watch towards your face for reading.

To turn Power Saving on and off

Operation

24 min. 5 hours 54 hours 15 hours

48 min. 8 hours 110 hours 30 hours

1. In the Timekeeping Mode, hold down E until the currently selected city code starts to ﬂ ash. This is the city code setting screen.

• Before the cit y code starts to ﬂ ash, the m essage SET Hold

will appear o n the display. Keep E depressed u ntil SET Hold disappear s and the cit y code star ts to ﬂ ash.

Level 5 Level 4 Level 3 Level 2 Level 1

Level Change *2

All functions are disabled, but timekeeping is maintained.

2. Use D to display the Power Saving On/Off screen shown nearby.

OFF

Power saving

Power saving on indicator

on indicator

3. Press A to toggle Power Saving on (On) and off (

4. Press E twice to exit the setting screen.

• The Power Sav ing on indicato r (PS) is on the display in a ll modes

while Power S aving is turne d on.

Operation Guide 3172

Radio Controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly. However, when using the watch outside of areas covered by time calibration signals, you will have to adjust the settings manually as required. See “Conﬁ guring Current Time and Date Settings Manually” for more information. This section explains how the watch updates its time settings when the city code selected as the Home City is in Japan, North America, Europe, or China, and is one that supports time calibration signal reception.

If your Home City Code setting is this:

LIS, LON, MAD, PAR, ROM, BER, STO, ATH, MOW Anthorn (England), Mainﬂ ingen (Germany)

HKG, BJS Shangqiu City (China)

TPE, SEL, TYO Fukushima (Japan), Fukuoka/Saga (Japan)

HNL, ANC, YVR, LAX, YEA, DEN, MEX, CHI, NYC, YHZ, YYT

Important!

• The areas covered by

certain conditions may cause reception problems.

HKG

• When

time calibration signal. You need to switch manually between standard time and daylight saving time (DST) if required. See “To conﬁ gure Home City settings” for information about how to do this.

MOW,HNL

and

BJS

is selected as the Home City, only the time and date are adjusted according to the

Approximate Reception Ranges

UK and German Signals

Anthorn

500 kilometers

1,500 kilometers

The Anthorn signal is receivable within this area

Japanese Signals Chinese Signal

500 kilometers

Fukuoka/Saga

• Even when the watch is within range of a transmitter, signal reception may be impossible due to the

effects of geographic contours, structures, weather, the time of year, the time of day, radio interference, etc. The signal becomes weaker at distances of approximately 500 kilometers, which means that the inﬂ uence of the conditions listed above becomes even greater.

• Signal reception may not be possible at the distances noted below during certain times of the year or

day. Radio interference may also cause problems with reception. Mainﬂ ingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310 miles) Fort Collins (United States) transmitter: 600 miles (1,000 kilometers) Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles) Shangqiu (China) transmitter: 500 kilometers (310 miles)

• As of January 2009, China does not use Daylight Saving Time (DST). If China does go to the Daylight

Saving Time system in the future, some functions of this watch may no longer operate correctly.

To get ready for a receive operation

1. Conﬁ rm that the watch is in the Timekeeping Mode. If it isn’t, use D to enter the Timekeeping Mode.

2. The antenna of this watch is located on its 12 o’clock side. Position the watch with 12 o’clock facing

towards a window as shown in the nearby illustration. Make sure there are no metal objects nearby.

Fukushima

Signals are receivable in the Taiwan area when reception conditions are

12 o’clock

Mainflingen

1,000 kilometers

ood.

• Signal rece ption may be dif ﬁ cult or even imp ossible und er the condit ions describ ed below.

Inside or among buildings

3. What you should do next depends on whether you are using Auto Receive or Manual Receive.

• Auto Receive: L eave the watch over nigh t in the locati on you selecte d in step 2. See “Auto

Receive” bel ow for details .

• Manual Re ceive: Perfo rm the operati on under “To per form manua l receive”.

Inside a vehicle

Near household appliances, ofﬁ ce equipment, or a mobile phone

The watch can receive the signal from the transmitter located here:

Fort Collins, Colorado (United States)

ANC

are quite far from the calibration signal transmitters, so

North American Signal

2,000 miles (3,000 kilometers)

600 miles (1,000 kilometers)

Fort Collins

500 kilometers

1,500 kilometers

• Signal rece ption norma lly is better at n ight.

• The receive o peration ta kes from two to s even minutes,

but in some c ases it can ta ke as long as 14 minutes . Take care that you do n ot perfor m any button o peration or move the watch duri ng this time.

Near a construction site, airport, or other sources of electrical noise

Near high-tension power lines

Changchun

Beijing Shangqiu Shanghai Chengdu Hong Kong

Among or behind mountains

Auto Receive

• With Auto Receive, the watch performs the receive operation each day automatically up to six times (up

to ﬁ ve times for the Chinese calibration signal) between the hours of midnight and 5 a.m. (according to the Timekeeping Mode time). When any receive operation is successful, none of the other receive operations for that day are performed.

• When a calibration time is reached, the watch will perform the receive operation only if it is in the

Timekeeping Mode or World Time Mode. The receive operation is not performed if a calibration time is reached while you are conﬁ guring settings.

• You can use the procedure under “To turn auto receive on and off” to enable or disable auto receive.

To perform manual receive

Receiving

Receiving indicator

indicator

Receive successful

Receive failed

If there was a previously

successful reception

If no reception was

successful

Signal Level Indicator

Signal level indicatorSignal level indicator

To check the latest signal reception results

Receiving

Receiving indicator

indicator

To turn auto receive on and off

On/Off

Receiving

Receiving indicator

indicator

On/Off status

status

1. Use D to select the Receive Mode (R/C) as shown in “Selecting a Mode”.

2. Hold down A.

• Keep A depressed u ntil RC Hold appears on th e display and the

receiving i ndicator sta rts ﬂ ashing.

• A signal level indi cator (L1, L2, or L3, see “S ignal Level Indi cator”)

appears on t he display afte r reception sta rts. Do no t move the watch or perfo rm any butto n operation un til GET or ERR appears in the upper le ft corne r of the screen.

• If the receive o peration is su ccessful, t he reception da te and time

appear on th e display, along wit h the GET indicator. The watch will ret urn to the Time keeping Mod e if you press D or if you do not pe rform any bu tton operat ion for abou t two or thre e minutes.

• If the current re ception fails bu t a previous rece ption (within th e

last 24 hours) was suc cessful, th e display shows t he receiving indicator and the ERR indicator. If the ERR indicator onl y is displayed (with out the recei ving indicator), it m eans that all of t he receive oper ations over the p ast 24 hours have fai led. The watch will ret urn to the Time keeping Mod e without ch anging the time set ting if you pre ss D or if you do not p erform any b utton operation f or about tw o or three minu tes.

Note

o interrupt a receive operation and return to the Receive Mode, press

During manual receive, the signal level indicator displays the signal level as shown below.

Weak (Unstable) Strong (Stable)

As you watch the indicator, keep the watch in a location that best maintains stable reception.

• Even under optimum reception conditions, it can take about 10

seconds for reception to stabilize.

• Note that weather, the time of day, surroundings, and other factors all

can affect reception.

Enter the Receive Mode.

• When receive is successful, the display shows the time and date that

receive was successful. operations were successful.

• To return to the Timekeeping Mode, press D.

Note

The receiving indicator will not be displayed if you have adjusted the time or date setting manually since the last receive operation.

- : - -

indicates that none of the reception

1. Enter the Receive Mode.

2. In the Receive Mode, hold down E until the current auto receive setting (On or setting screen.

• Note that the s etting scre en will not appe ar if the curre ntly selected

Home Cit y is one that do es not suppo rt time cali bration recept ion.

3. Press A to toggle auto receive on (On) and off (

OFF

) and receiving indicator start to ﬂ ash. This is the

OFF

4. Press E to exit the setting screen.

Operation Guide 3172

Radio-controlled Atomic Timekeeping Precautions

• Strong electrostatic charge can result in the wrong time setting.

• Even if a receive operation is successful, certain conditions can cause the time setting to be off by up

to one second.

• The watch is designed to update the date and day of the week automatically for the period January 1,

2000 to December 31, 2099. Updating of the date by signal reception will no longer be performed starting from January 1, 2100.

• If you are in an area where signal reception is not possible, the watch keeps time with the precision

noted in “Speciﬁ cations”.

• The receive operation is disabled under any of the following conditions.

– While power is at Level 3 (L) or lower – While the watch is in the power recovery mode – While a sensor operation is being performed – When the watch is in the function sleep state (“Power Saving”) – While a countdown timer operation is in progress

• A receive operation is cancelled if an alarm sounds while it is being performed.

• The Home City setting reverts to the initial default of

drops to Level 5 or when you have the rechargeable battery replaced. If this happens, change the Home City to the setting you want.

Selecting a Mode

• The illustration below shows which buttons you need to press to navigate between modes.

• For about one second after you enter a mode by pressing D, a pointer will appear on the display

pointing the applicable mode name on the watch's bezel.

• In any mode, press L to illuminate the display.

World Time

Mode

Data Recall

Mode

TYO

(Tokyo) whenever the battery power level

Timekeeping Mode

Sunrise/Sunset

Mode

Mode Reference Guide

Your watch has 11 “modes”. The mode you should select depends on what you want to do.

To do this: Enter this mode:

• View the current date in the Home City

• Conﬁ gure Home City and daylight saving time (DST) settings

• Conﬁ gure time and date settings manually

View the sunrise and sunset times for a speciﬁ c date Sunrise/Sunset Mode

• Determine your current bearing or the direction from your current

location to a destination as a direction indicator and angle value

• Determine your current location using the watch and a map

• View the barometric pressure and temperature at your current location

• View a graph of barometric pressure readings

• View the altitude at your current location

• Determine the altitude differential between two locations (reference

point and current location)

• Record an altitude reading with the measurement time and date

Recall records created in the Altimeter Mode Data Recall Mode

View the current time in one of 48 cities (31 time zones) around the globe World Time Mode

Use the stopwatch to measure elapsed time Stopwatch Mode

Use the countdown timer Countdown Timer Mode

Set an alarm time Alarm Mode

• Perform a time calibration receive operation

• Check whether the last receive operation was successful

• You can use buttons A,B, and C to enter a sensor mode directly from the Timekeeping Mode or

from another sensor mode. To enter a sensor mode from the Sunrise/Sunset Mode, Data Recall, World Time, Stopwatch, Countdown Timer, Alarm, or Receive Mode, ﬁ rst enter the Timekeeping Mode and then press the applicable button.

Sensor Modes

Timekeeping Mode

Digital Compass Mode

Barometer/Thermometer Mode

Altimeter Mode

Receive Mode

Countdown

Stopwatch Mode

General Functions (All Modes)

The functions and operations described in this section can be used in all of the modes.

Auto Return Features

• The watch returns to the Timekeeping Mode automatically if you do not perform any button operation

for two or three minutes in the Sunrise/Sunset, Data Recall, Alarm, Receive, or Digital Compass Mode.

• If you leave a screen with ﬂ ashing digits on the display for two or three minutes without performing any

operation, the watch exits the setting screen automatically.

Initial Screens

When you enter the World Time, Alarm, or Digital Compass Mode, the data you were viewing when you last exited the mode appears ﬁ rst.

Scrolling

TheA and C buttons are used on the setting screen to scroll through data on the display. In most cases, holding down these buttons during a scroll operation scrolls through the data at high speed.

Countdown Timer Mode

Timer Mode

Alarm Mode Receive Mode

Timekeeping

Use the Timekeeping Mode to set and view the current time and date.

• Pressing E while in the Timekeeping Mode will cycle through the Timekeeping Mode display formats

as shown below.

Day of the Week Screen Year Screen Barometric Pressure

Day of week

Month Day

Year

indicator

Graph Screen

Barometric pressure graph

Digital Compass Mode

Barometer/

Thermometer Mode

Altimeter Mode

Barometer/

Conﬁ guring Home City Settings

There are two Home City settings: actually selecting the Home City and selecting either standard time or daylight saving time (DST).

City

City code

code

Month

Month Day

Day

SecondsHour : Minutes

To conﬁ gure Home City settings

1. In the Timekeeping Mode, hold down E until the currently selected city code starts to ﬂ ash. This is the city code setting screen.

• Before the cit y code starts to ﬂ ash, the m essage SET Hold

will appear o n the display. Keep E depressed u ntil SET Hold disappear s and the cit y code star ts to ﬂ ash.

• The watch will exi t the settin g mode automat ically if you d o not

perform a ny operation f or about tw o or three minu tes.

• For details about city codes, see the “City Code Table”.

2. Press A (East) and C (West) to select the city code you want to use as your Home City.

• Keep pressin g A or C until the cit y code you wan t to select as

your Home C ity appea rs on the display.

3. Press D to display the DST setting screen.

UseA to cycle through the DST settings in the sequence shown below.

Auto DST (AUTO) DST off (OFF)

DST on (On)

PM indicator

indicator

DST indicator

• The Auto DS T (AUTO) setti ng will be availabl e only when a ci ty code that s upports t ime calibrati on

signal recept ion is selecte d as the Home C ity. While Auto D ST is selected t he DST set ting will be changed aut omatically i n accordanc e with time cal ibration sig nal data.

• Note that you c annot switch b etween sta ndard time an d daylight saving t ime (DST ) while UTC is

selected as yo ur Home Cit y.

5. After all the settings are the way you want, press E twice to return to the Timekeeping Mode.

SecondsHour : Minutes

• The DST indicator a ppears to indi cate that Dayligh t Saving Tim e is turned on.

Note

• After you sp ecify a cit y code, the watch w ill use UTC* of fsets in the Wo rld Time Mod e to calculate

the current ti me for other ti me zones base d on the current t ime in your Ho me City.

* Coordinated Universal Time, the world-wide scientiﬁ c standard of timekeeping.

The reference point for UTC is Greenwich, England.

• Selectin g some cit y codes autom atically ma kes it possibl e for the watch to rece ive the time

calibratio n signal for the c orrespon ding area. Se e “Radio Co ntrolled Atom ic Timekee ping” for details.

Operation Guide 3172

To change the Daylight Saving Time (summer time) setting

DST indicatorDST indicator

1. In the Timekeeping Mode, hold down E until the currently selected city code starts to ﬂ ash. This is the city code setting screen.

• Before the cit y code starts to ﬂ ash, the m essage SET Hold

will appear on the display. Keep E depressed u ntil SET Hold disappear s and the cit y code star ts to ﬂ ash.

2. Press D to display the DST setting screen.

3. Use A to cycle through the DST settings in the sequence shown below.

Auto DST (AUTO)

• The Auto DST ( AUTO) settin g will be available o nly when a cit y

code that supports time calibration signal reception is selected as the Home City. While Auto DST is selected the DST setting will be changed automatically in accordance with time calibration signal data.

4. After all the settings are the way you want, press E twice to return to the Timekeeping Mode.

• The DST indicator appears to indicate that Daylight Saving Time is

turned on.

DST off (

OFF

DST on (On)

)

Conﬁ guring Current Time and Date Settings Manually

You can conﬁ gure current time and date settings manually when the watch is unable to receive a time calibration signal.

To change the current time and date settings manually

City

City code

code

Month

Month Day

Day

SecondsHour : Minutes

PM indicator

indicator

1. In the Timekeeping Mode, hold down E until the currently selected city code starts to ﬂ ash. This is the city code setting screen.

• Before the cit y code starts to ﬂ ash, the m essage SET Hold

will appear on the display. Keep E depressed u ntil SET Hold disappear s and the cit y code star ts to ﬂ ash.

2. Use A and C to select the city code you want.

• Select your Home City code before changing any other setting.

• For full info rmation on c ity codes , see the “Cit y Code Table”.

3. Press D to move the ﬂ ashing in the sequence shown below to select the other settings.

City Code

Thermometer/Barometer/ Altitude unit

DST

12/24-Hour Format

Power Saving

Seconds Hour Minutes Year

Illumination Duration

Button Operation Tone On/Off

Day Month

• The follow ing steps expla in how to conﬁ gure timekee ping settin gs only.

4. When the timekeeping setting you want to change is ﬂ ashing, use A and/or C to change it as described below.

Screen To do this: Do this:

Change the city code Use A (East) and C (West).

Cycle between Auto DST ( Time (On) and Standard Time (

Toggle between 12-hour ( timekeeping.

Reset the seconds to

Change the hour or minutes

Change the year, month, or day

AUTO

), Daylight Saving

OFF

12H

) and 24-hour (

24H

)

PressA.

UseA (+) and C (–).

5. Press E twice to exit the setting screen.

Note

• For information about selecting a Home City and conﬁ guring the DST setting, see “Conﬁ guring

Home City Settings”.

• While 12-ho ur format is s elected for ti mekeeping, a P (P M) indicator w ill appear fo r times from

noon to 11:59 p.m. No indic ator appear s for times fro m midnight to 11:59 a.m. Wit h 24-hou r format, time is displaye d from 0:0 0 to 23:59, wit hout any P (PM) indicator.

• The watch’s built- in full automa tic calendar m akes allowanc es for diffe rent month len gths and leap

years. Once y ou set the date, th ere should be no re ason to chang e it except after yo u have the watch’s rechargeabl e battery rep laced or afte r power drops to Level 5 .

Digital Compass

In the Digital Compass Mode, a built-in bearing sensor detects magnetic north at regular intervals and indicates one of 16 directions on the display.

12 o’clock

Direction

12 o’clock

Direction

position

indicator

position

indicator

Angle value (in degrees)

WNW

270

WSW

SSW

180

SSE

Current

Current time

time

NNW

ESE

To take a digital compass reading

North

1. Make sure the watch is in the Timekeeping Mode or any one of the

pointer

NNE

sensor modes.

• The senso r modes are: Digit al Compas s Mode, Barom eter/

Thermo meter Mode, an d Altimeter M ode.

2. Place the watch on a ﬂ at surface. If you are wearing the watch, make sure that your wrist is horizontal (in relation to the horizon).

3. Point the 12 o’clock position of the watch in the direction you want to measure.

4. Press C to start digital compass measurement.

• COMP will appear on th e display to indic ate that a digital c ompass

operation is in progress.

• See “Dig ital Compa ss Readings” fo r informati on about wh at

appears on the display.

Note

• If a value appea rs to the right of the d irection indic ator, it means

ENE

that the bear ing memor y screen is disp layed. If this happ ens, press

to exit the bea ring memor y screen.

5. After you are ﬁ nished using the digital compass, press D to return to the Timekeeping Mode.

Digital Compass Readings

• When you press Cto start digital compass measurement,

indicate that a digital compass operation is in progress.

• About two seconds after you start a digital compass measurement operation, letters on the display will

indicate the direction that the 12 o’clock position of the watch is pointing. Four pointers that indicate magnetic north, south, east, and west also will appear.

• After the ﬁ rst reading is obtained, the watch will continue to take digital compass readings automatically

each second for up to 20 seconds. After that, measurement will stop automatically.

• The direction indicator and angle value will show

complete.

• The auto light switch is disabled during the 20 seconds that digital compass readings are being taken.

• The following table shows the meanings of each of the direction abbreviations that appear on the

display.

Direction Meaning Direction Meaning Direction Meaning Direction Meaning

North

East

South

West

• The margin of error for the angle value and the direction indicator is ±11 degrees while the watch is

horizontal (in relation to the horizon). If the indicated direction is northwest (NW) and 315 degrees, for example, the actual direction can be anywhere from 304 to 326 degrees.

• Note that taking a measurement while the watch is not horizontal (in relation to the horizon) can result in

large measurement error.

•

You can calibrate the bearing sensor if you suspect the direction reading is incorrect.

• Any ongoing direction measurement operation is paused temporarily while the watch is performing an

alert operation (daily alarm, Hourly Time Signal, countdown timer alarm) or while illumination is turned on (by pressing L). The measurement operation resumes for its remaining duration after the operation that caused it to pause is ﬁ nished.

• See “Digital Compass Precautions” for important information about taking direction readings.

Calibrating the Bearing Sensor

You should calibrate the bearing sensor whenever you feel that the direction readings being produced by the watch are off. There are three different calibration methods available: magnetic declination correction, bidirectional calibration, and northerly calibration.

Magnetic Declination Correction

•

With magnetic declination correction, you input a magnetic declination angle (difference between magnetic north and true north), which allows the watch to indicate true north. You can perform this procedure when the magnetic declination angle is indicated on the map you are using. Note that you can input the declination angle in whole degree units only, so you may need to round off the value speciﬁ ed on the map. If your map indicates the declination angle as 7.4°, you should input 7°. In the case of 7.6° input 8°, for 7.5° you can input 7° or 8°.

Bidirectional Calibration and Northerly Calibration

•

Bidirectional calibration and northerly calibration calibrate the accuracy of the bearing sensor in relation to magnetic north. Use bidirectional calibration when you want to take readings within an area exposed to magnetic force. This type of calibration should be used if the watch becomes magnetized for any reason. With northerly calibration, you “teach” the watch which way is north (which you have to determine with another compass or some other means).

Important!

The more correctly you perform bidirectional calibration, the better the accuracy of the bearing sensor readouts. You should perform bidirectional calibration whenever you change environments where you use the bearing sensor, and whenever you feel that the bearing sensor is producing incorrect readings.

NNE

ESE

SSW

WNW

To perform magnetic declination correction

Magnetic declination

Magnetic declination angle direction value

angle direction value (E, W, or OFF)

(E, W, or OFF)

Magnetic declination

Magnetic declination angle value

angle value

Precautions about bidirectional calibration

• You can use any two opposing directions for bidirectional calibration. You must, however, make sure

that they are 180 degrees opposite each other. Remember that if you perform the procedure incorrectly, you will get wrong bearing sensor readings.

• Do not move the watch while calibration of either direction is in progress.

• You should perform bidirectional calibration in an environment that is the same as that where you plan

to be taking direction readings. If you plan to take direction readings in an open ﬁ eld, for example, calibrate in an open ﬁ eld.

To perform bidirectional calibration

3. Place the watch on a level surface facing any direction you want, and press C to calibrate the ﬁ rst

direction.

• - - - is shown on th e display while c alibration is b eing perfo rmed. Whe n calibration i s successfu l,

the display wil l show OK and -2-, and the n orth pointe r ﬂ ashing at the 6 o’clo ck positio n. This means that t he watch is ready for ca libration of t he second dire ction.

North-

northeast

East-

southeast

South-

southwest

West-

northwest

1. In the Digital Compass Mode, hold down E until the current magnetic declination settings start to ﬂ ash on the display. This is the setting screen.

•

Before the magnetic declination settings start to ﬂ ash, the message

SET Hold will appear on the display. Keep E depressed u ntil SET Hold disappears and the magnetic declination settings start to

ﬂ a s h .

2. Use A (East) and C (West) to change the settings.

•

The following explains magnetic declination angle direction settings.

OFF

: No magnetic declination correction performed. The magnetic

declination angle with this setting is 0°.

: When magnetic north is to the east (east declination)

: When magnetic north is to the west (west declination)

• You can select a valu e within the ran ge of W 90° to E 9 0° with

these settings.

• You can turn off (OFF) magnetic declination correction by pressing

and C at the same ti me.

• The illustration, for example, shows the value you should input

and the direction setting you should select when the map shows a magnetic declination of 1° West.

3. When the setting is the way you want, press E to exit the setting screen.

1. In the Digital Compass Mode, hold down E until the current magnetic declination settings start to ﬂ ash on the display. This is the setting screen.

• Before the magnetic declination settings start to ﬂ ash, the

message SET Hold will appear on the display. Keep E depressed until SET Hold disappears and the magnetic declination settings start to ﬂ ash.

2. Press D to display the bidirectional calibration screen.

• At this time, t he north po inter ﬂ ashes at th e 12 o’clock positio n

and the displ ay will show -1- to i ndicate that the watc h is ready to calibrate the ﬁ rst direction.

COMP

will appear on the display initially to

- - -

to indicate that digital compass readings are

Northeast

Southeast

Southwest

Northwest

ENE

SSE

WSW

NNW

East-

northeast

South-

southeast

West-

southwest

North-

northwest

4. Rotate the watch 180 degrees.

5. Press C again to calibrate the second direction.

• - - - is shown on th e display while c alibration is b eing perfo rmed. Whe n calibration i s successfu l,

the display wil l show OK and then ch ange to the Digi tal Compas s Mode scree n (- - -).

+ 8 hidden pages