Casio LK93TV User Manual

USER’S GUIDE GUÍA DEL USUARIO

LK93TV-ES-1

GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (not applicable to other areas).

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Declaration of Conformity

Model Number: LK-93TV Trade Name: CASIO COMPUTER CO., LTD. Responsible party: CASIO, INC. Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801 Telephone number: 973-361-5400 This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Important!

Please note the following important information before using this product.

• Before using the optional AD-5 Adaptor to power the unit, be sure to check the AC Adaptor for any damage first. Carefully check the power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC adaptor that is seriously damaged.

• Never attempt to recharge batteries.

• Do not use rechargeable batteries.

• Never mix old batteries with new ones.

• Use recommended batteries or equivalent types.

• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated near the battery compartment.

• Replace batteries as soon as possible after any sign they are getting weak.

• Do not short-circuit the battery terminals.

• The product is not intended for children under 3 years.

• Use only CASIO AD-5 adaptor.

• The AC adaptor is not a toy.

• Be sure to disconnect the AC adaptor before cleaning the product.

This mark applies in EU countries only.

CASIO Europe GmbH Bornbarch 10, 22848 Norderstedt, Germany

659A-E-002A

Safety Precautions

Congratulations on your selection of the CASIO electronic musical instrument.

• Before using the instrument, be sure to carefully read through the instructions contained in this manual.

• Please keep all information for future reference.

Symbols

Various symbols are used in this user’s guide and on the product itself to ensure that the product is used safely and correctly, and to prevent injury to the user and other persons as well as damage to property. Those symbols along with their meanings are shown below.

DANGER

This symbol indicates information that, if ignored or applied incorrectly, creates the danger of death or serious personal injury.

WARNING

This indication stipulates matters that have the risk of causing death or serious injury if the product is operated incorrectly while ignoring this indication.

Symbol Examples

This triangle symbol ( ) means that the user should be careful. (The example at left indicates electrical shock caution.)

This circle with a line through it ( means that the indicated action must not be performed. Indications within or nearby this symbol are specifically prohibited. (The example at left indicates that disassembly is prohibited.)

The black dot ( indicated action must be performed. Indications within this symbol are actions that are specifically instructed to be performed. (The example at left indicates that the power plug must be unplugged from the electrical socket.)

)

) means that the

CAUTION

This indication stipulates matters that have the risk of causing injury as well as matters for which there is the likelihood of occurrence of physical damage only if the product is operated incorrectly while ignoring this indication.

659A-E-003A

E-1

Safety Precautions

DANGER

Alkaline Batteries

Perform the following steps immediately if fluid leaking from alkaline batteries ever gets into your eyes.

1. Do not rub your eyes! Rinse them with water.

2. Contact your physician immediately.

Leaving alkaline battery fluid in your eyes can lead to loss of sight.

WARNING

Smoke, Strange Odor, Overheating

Continued use of the product while it is emitting smoke, a strange odor, or heat creates the risk of fire and electric shock. Take the following steps immediately.

1. Turn off power.

2. If you are using the AC adaptor for power, unplug it from the wall outlet.

3. Contact your original retailer or an authorized CASIO Service Provider.

AC Adaptor

● Misuse of the AC adaptor creates the risk of fire and electric shock. Always make sure you observe the following precautions.

• Be sure to use only the AC adaptor

that is specified for this product.

• Use only a power source whose

voltage is within the rating marked on the AC adaptor.

• Do not overload electrical outlets and

extension cords.

● Misuse of the AC adaptor’s electric cord can damage or break it, creating the risk of fire and electric shock. Always make sure you observe the following precautions.

• Never place heavy objects on the cord

or subject it to heat.

• Never try to modify the cord or subject

it to excessive bending.

• Never twist or stretch the cord.

• Should the electric cord or plug

become damaged, contact your original retailer or authorized CASIO Service Provider.

● Never touch the AC adaptor while your hands are wet. Doing so creates the risk of electric shock.

● Use the AC adaptor where it will not be splashed with water. Water creates the risk of fire and electric shock.

● Do not place a vase or any other container filled with liquid on top of the AC adaptor. Water creates the risk of fire and electric shock.

Batteries

Misuse of batteries can cause them to leak, resulting in damage to nearby objects, or to explode, creating the risk of fire and personal injury. Always make sure you observe the following precautions.

• Never try to take batteries apart or allow them to become shorted.

• Never expose batteries to heat or dispose of them by incineration.

• Never mix old batteries with new ones.

• Never mix batteries of different types.

• Do not charge the batteries.

• Make sure the positive (+) and negative

(–) ends of the batteries are facing correctly.

Do not incinerate the product.

Never throw the product into fire. Doing so can cause it to explode, creating the risk of fire and personal injury.

Water and Foreign Matter

Water, other liquids, and foreign matter (such as pieces of metal) getting into the product create the risk of fire and electric shock. Take the following steps immediately.

1. Turn off power.

2. If you are using the AC adaptor for power, unplug it from the wall outlet.

3. Contact your original retailer or an authorized CASIO Service Provider.

Disassembly and Modification

Never try to take this product apart or modify it in any way. Doing so creates the risk of electric shock, burn injury, or other personal injury. Leave all internal inspection, adjustment, and maintenance up to your original retailer or authorized CASIO Service Provider.

E-2

659A-E-004A

Safety Precautions

Dropping and Impact

Continued use of this product after it has been damaged by dropping or subjecting it to strong impact creates the risk of fire and electric shock. Take the following steps immediately.

1. Turn off power.

2. If you are using the AC adaptor for power, unplug it from the wall outlet.

3. Contact your original retailer or an authorized CASIO Service Provider.

Plastic Bags

Never place the plastic bag the product comes in over your head or in your mouth. Doing so creates the risk of suffocation. Particular care concerning this precaution is required where small children are present.

Keep off of the product and stand.*

Climbing onto the product or stand can cause it to tip over or become damaged. Particular care concerning this precaution is required where small children are present.

Location

Avoid locating the product on an unstable stand, on an uneven surface, or any other unstable location. An unstable location can cause the product to fall over, creating the risk of personal injury.

CAUTION

AC Adaptor

● Misuse of the AC adaptor creates the risk of fire and electric shock. Always make sure you observe the following precautions.

• Do not locate the electric cord near a

stove or other sources of heat.

• Never pull on the cord when

unplugging from the electrical outlet. Always grasp the AC adaptor when unplugging.

● Misuse of the AC adaptor creates the risk of fire and electric shock. Always make sure you observe the following precautions.

• Insert the AC adaptor into the wall

outlet as far as it will go.

• Unplug the AC adaptor from the wall

outlet during lightening storms or before leaving on a trip or other longterm absence.

• At least once a year, unplug the AC

adaptor from the wall outlet and wipe away any dust that is built up in the area around the prongs of the plug.

Relocating the Product

Before relocating the product, always unplug the AC adaptor from the wall outlet and disconnect all other cables and connecting cords. Leaving cords connected creates the risk of damage to the cords, fire, and electric shock.

659A-E-005A

Cleaning

Before cleaning the product, always unplug the AC adaptor from the wall outlet first. Leaving the AC adaptor plugged in creates the risk of damage to the AC adaptor, fire, and electric shock.

Batteries

Misuse of batteries can cause them to leak resulting in damage to nearby objects, or to explode, creating the risk of fire and personal injury. Always make sure you observe the following precautions.

• Use only batteries that are specified for use with this product.

• Remove batteries from the product if you do not plan to use it for a long time.

E-3

Safety Precautions

Connectors

Connect only the specified devices and equipment to the product’s connectors. Connection of a non-specified device or equipment creates the risk of fire and electric shock.

Location

Avoid the following locations for this product. Such locations create the risk of fire and electric shock.

• Areas subject to high humidity or large amounts of dust.

• In food preparation areas or other areas subject to oil smoke.

• Near air conditioning equipment, on a heated carpet, in areas exposed to direct sunlight, inside of a vehicle parked in the sun, or any other area that subjects the product to high temperatures.

Display Screen

• Never push on the display screen’s LCD panel or subject it to strong impact. Doing so can cause the LCD panel’s glass to crack, creating the risk of personal injury.

• Should the LCD panel ever crack or break, never touch the liquid inside of the panel. LCD panel liquid can cause skin irritation.

• Should LCD panel liquid ever get inside your mouth, immediately wash out your mouth with water and contact your physician.

• Should LCD panel liquid ever get into your eyes or onto your skin, rinse with clear water for at least 15 minutes, and then contact a physician.

Sound Volume

Do not listen to music at very loud volumes for long periods. Particular care concerning this precaution is required when using headphones. High volume settings can damage your hearing.

Health Precaution

In extremely rare cases, exposure to strong sudden light or flashing light can cause momentary muscle spasms, loss of consciousness, or other physical problems with some individuals.

• If you suspect that you might be susceptible to any condition such as this, be sure to consult with your physician before using this product.

• Use this product in an area that is well illuminated.

• Should you ever feel any symptoms similar to those described above when using this product, stop using it immediately and contact your physician.

Heavy Objects

Never place heavy object on top of the product. Doing so can make the product top heavy, causing the product to tip over or the object to fall from it, creating the risk of personal injury.

Correct Stand* Assembly

An incorrectly assembled stand can tip over, causing the product to fall and creating the risk of personal injury. Make sure you assemble the stand correctly, following the assembly instructions that come with it. Make sure you mount the product on the stand correctly.

* Stand is available as an option.

IMPORTANT!

When using batteries, be sure to replace them or shift to one of the alternate power sources whenever you notice any of the following symptoms.

• Dim power supply indicator

• Instrument does not turn on

• Dim, difficult to read display

• Abnormally low speaker/headphone volume

• Distortion of sound output

• Occasional interruption of sound when playing at high volumes

• Sudden power failure when playing at high volumes

• Dimming of the display when playing at high volume

• Continued sound output even after you release a key

• A totally different tone may sound

• Abnormal rhythm pattern and demo tune play

• Abnormally low microphone volume

• Distortion of microphone input

• Dim power supply indicator when a microphone is used

• Sudden power failure when using the microphone

• Dimming of keyboard lights when notes sound

• Loss of power, sound distortion, or low volume when playing from a connected computer

E-4

659A-E-006A

Main Features

❐ 264 tones

A wide selection of tones includes stereo piano and synthesized sounds, drum sets, and much more. Other features include digital effects that control the acoustical characteristic of tones.

❐ PIANO BANK button

The touch of a button takes you directly to piano tones and piano lessons.

❐ Advanced 3-Step Lesson System

The 3-Step Lesson System lets you practice at your own pace. The keyboard automatically grades your performances, so you can trace your progress as you improve.

• 3-Step Lesson System: Use any of the keyboard’s built-in tunes and SMF data from a SmartMedia keyboard keys light to teach you the correct notes. First practice the timing of the notes. Next, play along at your own pace. Soon you will be ready for step three, where you play along at normal speed. * Note that key lights may be difficult to see under direct sunlight or under other very bright lighting.

• Evaluation System: The keyboard can be configured to rate your performances during Step 1, Step 2, and Step 3 lessons by assigning points. You can even have the keyboard report your points vocally, both part way through and at the end of a lesson.

❐ Karaoke

Simply connect the bundled microphone to the microphone jack and you can sing along with the keyboard’s built-in tunes and SMF data from a SmartMediaTM card.

❐ 100 built-in tunes, including piano pieces

Built-in tunes are divided into two groups: a Song Bank of 65 tunes with Auto Accompaniment, and a Piano Bank of 35 piano tunes. You can simply enjoy listening to the built-in tunes, or eliminate either hand part of a tune, and then play along on the keyboard.

card to learn to play as the

❐ 120 rhythms

A selection of rhythms cover rock, pops, jazz and just about any other musical style imaginable.

❐ Auto Accompaniment

Simply play a chord and the corresponding rhythm, bass, and chord parts play along automatically.

❐ Musical Information System

A big LCD screen graphically shows you fingerings and notes, making keyboard play more informative and enjoyable than ever before.

❐ Song Memory function

With lesson recording you can record as you play along with built-in tunes for later playback. Performance recording lets you record your performances, including Auto Accompaniment, in real time. When playing back recorded data, keyboard keys light in time with the melody.

❐ Storing and Playing Back Tune Data You Transferred from Your Computer

You can connect your keyboard to a computer, use special CASIO conversion software to convert SMF data you purchase or create to CASIO format, and then transfer it to the keyboard.

❐ SmartMediaTM Card Slot

You can load a card with a standard MIDI file (SMF) and play it back on the keyboard.

❐ VIDEO OUT Jack

Connect the keyboard to a TV equipped with a video input jack and you can view lesson information on your TV screen. You can also view lyric data for easy reading during karaoke. You can also specify the type of alphabet that should be used for TV screen display (Russian Cyrillic or Latin).

659A-E-007A

E-5

Contents

Safety Precautions .................... E-1

Main Features ............................ E-5

General Guide............................ E-8

Attaching the Score Stand ..................... E-10

Quick Reference .......................E-11

To play the keyboard .............................. E-11

Power Supply .......................... E-13

Using batteries ....................................... E-13

Using the AC Adaptor ............................. E-13

Auto Power Off ....................................... E-14

Power On Alert ....................................... E-14

Memory Contents ................................... E-14

Connections ............................ E-15

Phones/Output Jack ............................... E-15

USB port ................................................ E-15

Sustain/Assignable Jack ........................ E-15

Microphone Jack .................................... E-16

VIDEO OUT Jack ................................... E-16

Accessories and Options ....................... E-16

Playing a Built-in Tune............ E-19

To play back a Song Bank tune ............. E-19

To play back a Piano Bank tune ............. E-20

Musical Information System ................... E-20

Adjusting the Tempo............................... E-20

To pause playback ................................. E-21

To fast reverse ....................................... E-21

To fast forward ....................................... E-21

Looping a Musical Phrase ...................... E-21

To change the melody tone .................... E-22

Using the PIANO BANK Button ............. E-22

Advanced 3-Step Lesson ....... E-23

Evaluation Mode .................................... E-24

Using the Lesson Functions and

Evaluation Mode .................................... E-25

Step 1 – Master the timing. .................... E-25

Step 2 – Master the notes. ..................... E-26

Step 3 – Play at normal speed. .............. E-27

Using the Phrase Practice Mode ........... E-27

Voice Fingering Guide............................ E-28

Using the Metronome ............................. E-28

Basic Operations..................... E-17

To play the keyboard .............................. E-17

Selecting a Tone..................................... E-17

Using Tone Effects ................................. E-18

Turning the Key Light System

On and Off.............................................. E-18

E-6

Using a Microphone for

Karaoke .................................... E-29

Auto Accompaniment ............. E-31

Selecting a Rhythm ................................ E-31

Playing a Rhythm ................................... E-32

Using Auto Accompaniment ................... E-32

Using an Intro Pattern ............................ E-35

Using a Fill-in Pattern ............................. E-35

659A-E-008A

Contents

Using a Rhythm Variation ....................... E-35

Using a Fill-in Pattern with a Variation

Rhythm ................................................... E-36

Synchro Starting Accompaniment with

Rhythm Play ........................................... E-36

Finishing with an Ending Pattern ........... E-36

Song Memory Function .......... E-37

Parts and Tracks .................................... E-37

Recording Play Along with

a Built-in Tune ........................................ E-38

Playing Back a Lesson Recording ......... E-39

Recording a Performance ...................... E-39

Playing Back a Performance

Recording ............................................... E-41

Overdubbing a Performance

Recording ............................................... E-42

Connection to a Computer ..... E-48

Connecting to a Computer ..................... E-48

Expanding the Selections in the

Song Bank Tunes................................... E-49

General MIDI Tone ................................. E-50

Changing the Settings ............................ E-50

Using a SmartMedia Card....... E-52

Getting Ready ........................................ E-53

Reading a SmartMedia card .................. E-54

SmartMedia Card Error Messages ........ E-55

Troubleshooting ...................... E-57

Specifications .......................... E-59

Care of your keyboard ............ E-60

Deleting a Specific Part/Track ................ E-42

Keyboard Settings .................. E-43

Using Layer ............................................ E-43

Using Split .............................................. E-44

Using Layer and Split Together .............. E-44

Transposing the Keyboard ..................... E-45

Using Touch Response .......................... E-46

Adjusting Accompaniment and

Song Bank Volume ................................ E-46

Tuning the Keyboard .............................. E-47

Selecting the Alphabet Type for

TV Screen Display ................................. E-47

Appendix .................................... A-1

Tone List / Note Table............................... A-1

Drum Assignment List .............................. A-6

FINGERED Chord Chart .......................... A-7

Rhythm List .............................................. A-8

Song List .................................................. A-9

MIDI messages that can be sent and received using the USB port

Company and product names used in this manual may be registered trademarks of others.

659A-E-009A

E-7

General Guide

3 6 75 0 A8

B C

1 2 4 9

I IJ K L M ON

D E F G H

*2*

E-8

TR SQP

U V W X Y Z [ \ ] _ b c d

659A-E-010A

General Guide

NOTE

• This keyboard has two PLAY/STOP buttons. In this manual, the PLAY/STOP button that is located under the KARAOKE button is indicated as <PLAY/STOP>.

MIC VOLUME knob

KEY CONTROL/TRANSPOSE buttons

KARAOKE button

<PLAY/STOP> button

SONG MEMORY button

FUNCTION button

REVERB/CHORUS button

KEY LIGHT button

DATA ACCESS lamp

RHYTHM button

TONE button

● ADVANCED 3-STEP LESSON SYSTEM

PRACTICE PHRASE button

SCORING 1 to 3 button

STEP 1 to 3 button

SPEAK button

METRONOME button

LEFT button, TRACK 1 button

RIGHT button, TRACK 2 button

Speaker

MIC IN jack

RHYTHM list

TONE list

SONG BANK/KARAOKE list

Display

PIANO BANK list

CHORD root names

Percussion instrument list

SPLIT button

LAYER button

Voice 1 to 5 list

POWER button

Power indicator

MAIN VOLUME slider

MODE switch

● SONG/PIANO BANK/RHYTHM CONTROLLER

REPEAT button, INTRO button

REW button, NORMAL/FILL-IN button

[

FF button, VARIATION/FILL-IN button

PAUSE button, SYNCHRO/ENDING button

]

PLAY/STOP button, START/STOP button

Song/Piano Bank controller indicator

Rhythm controller indicator

SONG BANK button

PIANO BANK button

CARD button

TEMPO buttons

Controller Indicators

Song/Piano Bank controller indicator

Pressing the SONG BANK, PIANO BANK, or KARAOKE button causes the Song/Piano Bank controller indicator to light. This indicates that buttons Y through ] are currently functioning as playback control buttons.

Rhythm controller indicator

Pressing the RHYTHM button to enter the Rhythm Mode, or pressing the RHYTHM button and then the SONG MEMORY button to enter the Song Memory mode causes the Rhythm controller indicator to light. This indicates that buttons Y through ] are currently functioning as rhythm control buttons.

NOTE

• Display examples shown in this User’s Guide are intended for illustrative purposes only. The actual text and values that appear on the display may differ from the examples shown in this User’s Guide.

• Viewing a liquid crystal display screen from an angle can change the appearance of display contrast. The display contrast of this keyboard is set to allow easy viewing for a person seated on a chair in front of the keyboard. Note that display contrast is fixed, and cannot be adjusted.

659A-E-011A

E-9

General Guide

*1 Attaching the Score Stand

Insert both ends of the music stand provided with the keyboard into the two holes on the top surface.

Number buttons

[+]/[–]

buttons

• For input of numbers to change a displayed number or setting.

• Negative values cannot be input using the number buttons. Use [+] (increase) and [–] (decrease) instead.

Rear Panel

i j k

SUSTAIN/ASSIGNABLE JACK

DC 9V jack

PHONES/OUTPUT jack

Card slot

l m

USB port

VIDEO OUT jack

E-10

659A-E-012A

Quick Reference

SONG BANK

POWER indicator

POWER

This section provides a quick overview of keyboard operation using steps one and two of the 3-step lesson feature.

MODE

PLAY/STOP

To play the keyboard

Press the POWER button to turn on power.

• This causes the power indicator to light.

Lit

Set the MODE switch to NORMAL.

PIANO BANK

Number buttons

STEP2

STEP1

Find the tune you want to play in the SONG BANK/ KARAOKE List, and then use the number buttons to input its two-digit number.

• See page A-9 for the SONG BANK/KARAOKE List.

Example: To select “54 ALOHA OE”, input 5 and then

AlohaOe

Press the STEP 1 button or STEP 2 button.

• The keyboard sounds a count beat and waits for you to play something on the keyboard. The keys that you need to press first flash.

Play the melody along with the selected tune’s accompaniment.

• Play in accordance with the fingerings, notes, and dynamic marks that appear on the display.

FingeringNote pitch

Press the SONG BANK button.

659A-E-013A

AlohaOe

Indicator appears

E-11

Quick Reference

If you selected lesson Step 1

• Play the notes on the keyboard.

• Accompaniment (left-hand part) plays in time with

the notes.

• With Step 1, the correct melody note is played no matter which keyboard key you press.

If you selected lesson Step 2

• Play the correct notes on the keyboard.

• Press the keyboard key that lights. Note that with a

Piano Bank tune, the keyboard key light turns off as soon as you press the key.

• The keyboard key for the next note you will need to play flashes.

• Accompaniment (left-hand part) plays in time with the notes, as long as you press the correct keyboard keys.

To stop play at any time, press the PLAY/STOP button.

To play an Etude or Concert Piece tune

When you get to step 3 of the above procedure, press the PIANO BANK button in place of the SONG BANK button.

Indicator appears

Find the tune you want to play in the PIANO BANK List, and then use the number buttons to input its two-digit number.

• See page A-9 for the PIANO BANK List.

Next, continue from step 5 of the above procedure.

E-12

659A-E-014A

Power Supply

This keyboard can be powered by current from a standard household wall outlet (using the specified AC adaptor) or by batteries. Always make sure you turn the keyboard off whenever you are not using it.

Using batteries

Always make sure you turn off the keyboard before loading or replacing batteries.

To load batteries

Remove the battery compartment cover.

Load 6 AA-size batteries into the battery compartment.

• Make sure that the positive (+) and negative (–) ends are facing correctly.

Insert the tabs on the battery compartment cover into the holes provided and close the cover.

NOTE

• The keyboard may not function correctly if you load or replace batteries with power turned on. If this happens, turning the keyboard off and then back on again should return functions back to normal.

WARNING

• Never try to take batteries apart or allow them to become shorted.

• Never expose batteries to heat or dispose of them by incineration.

• Never mix old batteries with new ones.

• Never mix batteries of different types.

• Do not charge the batteries.

• Make sure the positive (+) and negative (–) ends of

the batteries are facing correctly.

CAUTION

Misuse of batteries can cause them to leak resulting in damage to nearby objects, or to explode, creating the risk of fire and personal injury. Always make sure you observe the following precautions.

• Use only batteries that are specified for use with this product.

• Remove batteries from the product if you do not plan to use it for a long time.

Using the AC Adaptor

Make sure that you use only the AC adaptor specified for this keyboard.

Specified AC Adaptor: AD-5

[Rear Panel]

DC 9V jack

AC adaptor AD-5

Important Battery Information

■ The following shows the approximate battery life.

Alkaline batteries .................................... 2.5 hours

The above value is standard battery life at normal temperature, with the keyboard volume at medium setting. Temperature extremes or playing at very loud volume settings can shorten battery life.

659A-E-015A

AC outlet

E-13

Power Supply

Note the following important precautions to avoid damage to the power cord.

● During Use

• Never pull on the cord with excessive force.

• Never repeatedly pull on the cord.

• Never twist the cord at the base of the plug or connector.

• The power cord should not be stretched tight while it is

in use.

● During Movement

• Before moving the keyboard, be sure to unplug the AC adaptor from the power outlet.

● During Storage

• Loop and bundle the power cord, but never wind it around the AC adaptor.

IMPORTANT!

• Make sure that the keyboard is turned off before connecting or disconnecting the AC adaptor.

• Using the AC adaptor for a long time can cause it to become warm to the touch. This is normal and does not indicate malfunction.

Auto Power Off

When you are using battery power, keyboard power turns off automatically whenever you leave it on without performing any operation for about 6 minutes. When this happens, press the POWER button to turn power back on.

NOTE

• Auto Power Off is disabled (it does not function) when you are using the AC adaptor to power the keyboard.

Power On Alert

Keyboard keys light to alert you if you leave power on and do not perform any operation for about 6 minutes. Note that keys light only, and no sound is produced. When this happens, press any button or keyboard key to clear the power on alert.

NOTE

• Power on alert operates only when you are powering the keyboard using the AC adaptor. It does not operate when you are using batteries.

To turn off power on alert

Press the FUNCTION button a number of times until “DEMO 2” appears on the display.

Use the [+] and [–] buttons to change the setting to “oFF”.

Press the FUNCTION button to clear the setting screen from the display.

Memory Contents

Even when the keyboard is turned off, song memory contents are retained as long as power is being supplied to the keyboard. Unplugging the AC adaptor when batteries are not loaded or when batteries are dead cuts off the power supply. This causes all keyboard settings to be initialized to the initial factory defaults, and clears all data stored in memory.

To disable Auto Power Off

Hold down the TONE button while turning on the keyboard to disable Auto Power Off.

NOTE

• When this function is turned off, the keyboard does not turn off automatically no matter how long it is left with no operation being performed.

• Auto Power Off is enabled again when you manually turn off power and then turn it back on again.

E-14

Power Requirements

Note the following precautions whenever you want to ensure that current keyboard settings and memory contents are not lost.

• Make sure the keyboard is being supplied power through the AC adaptor before replacing its batteries.

• Before unplugging the AC adaptor, make sure that fresh batteries are loaded in the keyboard.

Make sure that keyboard power is turned off before replacing batteries or unplugging the AC adaptor.

659A-E-016A

Connections

Phones/Output Jack

PREPARATION

• Before connecting headphones or other external equipment, be sure to first turn down the volume settings of the keyboard and the connected equipment. You can then adjust volume to the desired level after connections are complete.

[Rear Panel]

PHONES/OUTPUT jack

Keyboard amp, guitar amp, etc.

Audio connection

Stereo standard plug

White

LEFT

AUX IN or similar terminal

of audio amplifier

Connecting Headphones (Figure 1)

Connecting headphones cuts off output from the keyboard’s built-in speakers, so you can play even late at night without disturbing anyone.

Audio Equipment (Figure 2)

Connect the keyboard to an audio equipment using a commercially available connecting cord with a standard plug on one end and two PIN plugs on the other end. Note that the standard plug you connect to the keyboard must be a stereo plug, otherwise you will be able to output only one of stereo channels. In this configuration, you normally set the input selector of the audio equipment to the terminal (usually marked AUX IN or something similar) where the cord from the keyboard is connected. See the user documentation that comes with your audio equipment for full details.

Musical Instrument Amplifier (Figure 3)

Use a commercially available connecting cord to connect the keyboard to a musical instrument amplifier.

NOTE

• Be sure to use a connecting cord that has a stereo standard plug on the end you connect to the keyboard, and a connector that provides dual channel (left and right) input to the amplifier to which you are connecting. The wrong type of connector at either end can cause one of the stereo channels to be lost.

When connected to a musical instrument amplifier, set the volume of the keyboard to a relatively low level and make output volume adjustments using the amplifier’s controls.

RIGHT

Red

PIN plug

Connection Example

To keyboard’s PHONES/OUTPUT

ack

Stereo standard plug

PIN plug (red)

PIN plug (white)

PIN jack

INPUT 1

INPUT 2

Standard plug

Keyboard or guitar amp

USB port

You can also connect the keyboard to a computer. See “Connecting to a Computer” on page E-48 for details.

Sustain/Assignable Jack

You can connect an optional sustain pedal (SP-3 or SP-20) to the SUSTAIN/ASSIGNABLE JACK to enable the capabilities described below.

For details on how to select the pedal function you want, see “SUSTAIN/ASSIGNABLE JACK (Default: SUS)” on page E-51.

SUSTAIN/ASSIGNABLE JACK

SP-20

Sustain Pedal

• With piano tones, depressing the pedal causes notes to linger, much like a piano’s damper pedal.

• With organ tones, depressing the pedal causes notes to continue to sound until the pedal is released.

Sostenuto Pedal

• As with the sustain pedal function described above, depressing the sostenuto pedal causes notes to be sustained.

• This difference between a sostenuto pedal and sustain pedal is the timing. With a sostenuto pedal, you press the keys and then depress the pedal before you release the keys.

• Only the notes that are sounding when the pedal is depressed are sustained.

Soft Pedal

Depressing the pedal softens the sound of the notes being played.

Rhythm Start/Stop Pedal

In this case, the pedal performs the same functions as the START/STOP button.

659A-E-017A

E-15

Connections

Microphone Jack

You can connect a commercially available microphone to the microphone jack and sing along with notes played on the keyboard. For details, see “Using a Microphone for Karaoke” on page E-29.

VIDEO OUT Jack

You can connect the keyboard to a TV equipped with a video input jack, and view lessons*1 and song lyrics*2 on the TV screen.

*1: Lessons using built-in tunes or SMF data *2: Built-in tunes with lyric data or commercially available

SMF data with lyric data

Connecting to a TV

IMPORTANT!

• Make sure that both the keyboard and the TV are turned off before connecting them.

• Placing the keyboard on top of or too close to the TV can cause problems with the colors that appear on the TV screen. Keep the keyboard away from the TV.

Use the bundled video cable to connect the keyboard to a TV as shown below.

• Turn on the TV and perform the required operation to select its video input terminal.

• Turn on the keyboard.

IMPORTANT!

• See the user documentation that comes with your TV for information about how to configure the required settings.

• A TV normally supports either NTSC or PAL as its color system. The system supported by your keyboard matches the system used in the geographic area where you purchased it. The color system is also indicated on the rating plate on the bottom of the keyboard.

Keyboard Model Supported Color System

LK-93TV-N NTSC LK-93TV-P PAL

Images will not appear correctly on the TV screen if its color system does not match the color system of the keyboard. Make sure you check with your retailer before purchasing the keyboard outside of the area where you will normally use it.

Accessories and Options

Use only the accessories and options specified for this keyboard. Use of non-authorized items creates the danger of fire, electrical shock, and personal injury.

[Rear Panel]

VIDEO OUT jack

Turn on the TV and select its video input terminal.

E-16

Bundled video cable

TV / VIDEO

(Example)

To video

input terminal

TV with video input terminal

Video input port

(Yellow)

659A-E-018A

Basic Operations

KEY LIGHT

POWER

MAIN VOLUME

This section provides information on performing basic keyboard operations.

MODE

To play the keyboard

Press the POWER button to turn the keyboard on.

Set the MODE switch to NORMAL.

Use the MAIN VOLUME slider to set the volume to a relatively low level.

Play something on the keyboard.

TONE

Number buttons

[+] / [–]

Press the TONE button.

Indicator appears

Use the number buttons to input the three-digit tone number of the tone you want to select.

Example: To select “049 ACOUSTIC BASS”, input 0, 4

and then 9.

Selecting a Tone

This keyboard comes with 264 built-in tones. Use the following procedure to select the tone you want.

To select a tone

Find the tone you want to use in the TONE List and note its tone number.

• Not all of the available tones are shown on the tone list printed on the keyboard console. For a complete list, see the “Tone List” on page A-1.

• If the keyboard is connected to a TV, the tone list appears on the TV screen. For information about connecting to a TV, see “VIDEO OUT Jack” on page E-16.

Aco .Bsas

NOTE

• Always input all three digits for the tone number, including leading zeros (if any). If you input one or two digits and stop, the display will automatically clear your input after a few seconds.

• You can also increment the displayed tone number by pressing [+] and decrement it by pressing [–].

• When one of the drum sets is selected (tone numbers 256 through 263), each keyboard key is assigned a different percussion sound. See page A-6 for details.

659A-E-019A

E-17

Basic Operations

Polyphony

The term polyphony refers to the maximum number of notes you can play at the same time. The keyboard has 32-note polyphony, which includes the notes you play as well as the rhythms and auto-accompaniment patterns that are played by the keyboard. This means that when a rhythm or autoaccompaniment pattern is being played by the keyboard, the number of notes (polyphony) available for keyboard play is reduced. Also note that some of the tones offer only 16-note polyphony.

• When rhythm or auto accompaniment is playing, the number of sounds simultaneously played is reduced.

Digital Sampling

A number of the tones that are available with this keyboard have been recorded and processed using a technique called digital sampling. To ensure a high level of tonal quality, samples are taken in the low, mid, and high ranges and then combined to provide you with sounds that are amazingly close to the originals. You may notice very slight differences in volume or sound quality for some tones when you play them at different positions on the keyboard. This is an unavoidable result of multiple sampling, and it is not a sign of malfunction.

After turning on the effect you want, use the number buttons or the [+]/[–] buttons to select the effect type you want.

• Note that you need to select an effect type with the number buttons or the [+]/[–] buttons within a few seconds after turning on an effect. If you don’t, the display will exit the setting screen.

Effect List

Reverb 0: Room 1

1: Room 2 2: Hall 1 3: Hall 2

Chorus 0: Chorus 1

1: Chorus 2 2: Chorus 3 3: Chorus 4

Turning the Key Light System On and Off

Use the following procedure when you want to turn the key light system on or off.

Using Tone Effects

Reverb: Makes your notes resonate Chorus: Adds more breadth to your notes

Press the REVERB/CHORUS button to cycle through the effect settings as shown below.

• You can find out the current effect setting by looking at the REVERB and CHORUS indicators.

Reverb on

Chorus on

Both on

Off

Both off

To turn the key light system on and off

Press the KEY LIGHT button to toggle the key light system on and off.

• The KEY LIGHT indicator disappears when the key light system is turned off.

NOTE

• The key light system is turned on automatically whenever you turn on keyboard power.

E-18

659A-E-020A

Playing a Built-in Tune

REW

PLAY/STOPPAUSE

Your keyboard comes with a total of built-in 100 tunes. You can play back built-in tunes for your own listening pleasure, or you can use them for practice and even karaoke. Built-in tunes are divided between the two groups described below.

• Song Bank/Karaoke Group: 65 tunes for one-hand play The tunes in this group are Auto Accompaniment tunes. If you connect a microphone to the keyboard and enter the Karaoke Mode*, you can sing along with the built-in tune. * The Karaoke Mode reduces the volume of the melody

part of the built-in tunes and changes the tone selection to one that makes it easier for a vocalist to follow.

• Piano Bank Group: 35 tunes for two-hand play The piano tunes in this group are subdivided between 10 etudes and 25 concert pieces.

In addition to the built-in tunes, you can also play back the tunes you download over the Internet (E-49).

SONG BANK

PIANO BANKREPEAT

TEMPO

Use the number buttons to input the tune’s twodigit number.

Example: To select “54 ALOHA OE”, input 5 and then 4.

Song number Song name

AlohaOe

NOTE

• Tune Number 00 is the initial default Song Bank tune setting whenever you turn on keyboard power.

• You can also increment the displayed tune number by pressing [+] and decrement is by pressing [–].

Number buttons

[+] / [–]

To play back a Song Bank tune

PREPARATION

• Adjust the main volume (page E-17).

Find the tune you want to play in the SONG BANK/ KARAOKE List, and note its number.

• See page A-9 for the SONG BANK/KARAOKE List.

Press the SONG BANK button to enter the Song Bank Mode.

Indicator appears

659A-E-021A

Press the PLAY/STOP button to start play of the tune.

Staff display

AlohaOe

Chord name

Press the PLAY/STOP button to stop playback of the Song Bank tune.

• The tune you select continues to play until you stop it.

Fingering

E-19

Playing a Built-in Tune

To play back a Piano Bank tune

Find the tune you want to play in the PIANO BANK List, and note its number.

• See page A-9 for the PIANO BANK List.

Press the PIANO BANK button to specify the Piano Bank group.

Indicator appears

NOTE

• Pressing the PIANO BANK button changes the tone to stereo piano (Tone Number 000).

Use the number buttons to input the two-digit tune number you looked up in step 1.

Example: To select tune number 07 (Ode To Joy), input

0 and then 7.

OdeTo

Musical Information System

When the keyboard is playing one of its built-in tunes, the display shows a variety of information about the tune.

Example: Display during Song Bank play

Staff display

AlohaOe

Chord name

NOTE

• Chord names are not displayed for Piano Bank tunes.

Adjusting the Tempo

The tempo (beats per minute) can be set to a value in the range of 30 to 255. The tempo value you set is used for Song Bank, Piano Bank, karaoke, 3-step lesson, and Auto Accompaniment chord play, as well as playback from Song Memory, SmartMedia card, and metronome operation.

To set the tempo

Fingering

NOTE

• Tune Number 00 is the initial default Piano Bank tune setting whenever you turn on keyboard power.

• You can also change the displayed tune number using the [+] and [–] buttons.

Press the PLAY/STOP button to start playback.

To stop playback, press the PLAY/STOP button.

• The tune you select continues to play until you stop it.

E-20

Use the TEMPO buttons to set the tempo.

: Increases the tempo value. : Decreases the tempo value.

Flash

Tempo value

NOTE

• While the tempo value is flashing, you can also use the number buttons or [+] and [–] to input a three-digit value. Note that you must input leading zeros, so 90 is input as 090.

• Pressing both the and TEMPO buttons at the same time automatically returns the currently selected rhythm to its default tempo.

• Piano Bank tunes have tempo changes part way through in order to produce specific musical effects. Note that the tempo setting automatically returns to the default whenever a tempo change occurs within one of these tunes.

659A-E-022A

Playing a Built-in Tune

To pause playback

Press the PAUSE button while a tune is playing to pause it.

Pressing the PAUSE button again resumes play from the point where it was paused.

To fast reverse

While a tune is playing or paused, hold down the REW button to skip in a reverse direction at high speed.

• The fast reverse operation skips back one measure at a time.

• The measure and beat numbers on the display change while the fast reverse operation is being performed.

Beat numberMeasure number

Releasing the REW button starts song playback from the measure whose number is shown on the display.

NOTE

• Fast reverse does not work while tune play is stopped.

• Certain playback conditions can cause it to take some

time before fast reverse starts after you press the REW button.

To fast forward

While a tune is playing or paused, hold down the FF button to skip forward at high speed.

• The fast forward operation skips forward one measure at a time.

• The measure and beat numbers on the display change while the fast forward operation is being performed.

Beat numberMeasure number

Releasing the FF button starts song playback from the measure whose number is shown on the display.

NOTE

• Fast forward does not work while tune play is stopped.

Looping a Musical Phrase

You can select one or more measures and “loop” them, which means that they play again and again until you stop playback.

While the tune is playing, press the REPEAT button while the measure you want to start from is playing.

• This causes the repeat indicator to flash on the display, and displays the measure number of the start measure.

When playback is within the measure you want to specify as the end of the loop, press the REPEAT button again.

• This displays the measure number of the end measure, and starts repeat play of the loop.

• To cancel repeat play of a loop, press the REPEAT button again so the repeat indicator is not displayed.

659A-E-023A

E-21

Playing a Built-in Tune

To change the melody tone

Press the TONE button.

Indicator appears

Find the tone you want in the TONE List, and then use the number buttons to input its three-digit number.

Example: To select “057 VIOLIN”, input 0, then 5, then

• You can select any one of the keyboard’s 264 built-in

NOTE

• You can also use the [+] and [–] buttons to change the melody tones.

• For two-hand tunes (Piano Bank tunes), the same tone is applied for both the left and right hand parts.

• Specifying the tune number for the same tune that is currently selected returns the melody tone to the default setting for that tune.

tones.

Viol i

Using the PIANO BANK Button

Pressing the PIANO BANK button provides instant access to piano tones and piano tune selection.

Initial Piano Bank Setting

Tone: 000 Stereo Piano

To use the piano bank

Press the PIANO BANK button.

Indicator appears

Now try playing something on the keyboard.

• The notes you play sound with a piano tone.

If you want to playback the built-in tune, press the PLAY/STOP button.

• This causes the currently selected tune to play in an endless loop.

• To stop playback, press the PLAY/STOP button again.

To play all Song Bank tunes in succession

You can set up the keyboard to continually play its Song Bank tunes.

Press the SONG BANK button and the PIANO BANK button at the same time.

• Playback starts from Song Bank tune number 00.

To stop tune play, press the PLAY/STOP button again.

NOTE

• While a tune is playing, you can use the number buttons or [+] and [–] to change to another tune.

• You can play along with the tunes on the keyboard.

E-22

659A-E-024A

+ 55 hidden pages