Casio LK-170, LK-175, LK-260 User Guide
LK-170
EN/ES
LK-175
LK-260
USER’S GUIDE
Please keep all information for future reference.
Safety Precautions
Before trying to use the Digital Keyboard, be sure to
read the separate “Safety Precautions”.
GUÍA DEL USUARIO
Guarde toda información para tener como referencia futura.
Precauciones de seguridad
Antes de intentar usar el teclado digital, asegúrese de
leer las “Precauciones de seguridad” separadas.
EnglishEspañol
LK260/175-ES-1A
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION
NOTICE
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Bank select
Modulation
Data entry
Declaration of Conformity
Model Number: LK-170/LK-175/LK-260
Trade Name: CASIO COMPUTER CO., LTD.
Responsible party: CASIO AMERICA, INC.
Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801
Telephone number: 973-361-5400
This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
1 - 16
1 - 16
X
Mode 3
1
*
0 - 127
0 - 127
Important!
Please note the following important information before using this product.
• Before using the optional AD-E95100L Adaptor to power the unit, be sure to check the AC Adaptor for any damage first.
Carefully check the power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC
adaptor that is seriously damaged.
• Never attempt to recharge batteries.
• Do not use rechargeable batteries.
• Never mix old batteries with new ones.
• Use recommended batteries or equivalent types.
• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated near the battery compartment.
• Replace batteries as soon as possible after any sign they are getting weak.
• Do not short-circuit the battery terminals.
• The product is not intended for children under 3 years.
• Use only CASIO AD-E95100L adaptor.
• The AC adaptor is not a toy.
• Be sure to disconnect the AC adaptor before cleaning the product.
This mark applies in EU countries only.
1
1 - 16
X
Mode 3
36 - 96
Manufacturer:
CASIO COMPUTER CO.,LTD.
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Responsible within the European Union:
CASIO EUROPE GmbH
Casio-Platz 1, 22848 Norderstedt, Germany
**
X
9nH v = 1 - 127
O
9nH v = 0, 8nH v =
X
X
OX
O
X
X 9nH v = 0
1-127 (LK-260)
9nH v = 100 (LK-170/LK-175)
O
2
(MSB only)
*
OOOOO
X
X
O
0, 3216, 38
Volume
Pan
O
O
7
10
Expression
O
X
11
Default
Changed
Default
Messages
● Any reproduction of the contents of this manual, either in part or its entirety, is prohibited. Except for your own, personal
use, any other use of the contents of this manual without the consent of CASIO is prohibited under copyright laws.
● IN NO EVENT SHALL CASIO BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION) ARISING OUT OF THE
USE OF OR INABILITY TO USE THIS MANUAL OR PRODUCT, EVEN IF CASIO HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
● The contents of this manual are subject to change without notice.
● The actual appearance of the product may be different from that shown in the illustrations in this User’s Guide.
● Company and product names used in this manual may be registered trademarks of others.
Model: LK-170/LK-175/LK-260 Version : 1.0
Function Transmitted Recognized Remarks
Basic
Channel
Altered
Mode
True voice
Note
Number
Note ON
Note OFF
Velocity
Key’s
Ch’s
After
Touch
Pitch Bender
Control
Change
Contents
General Guide ............................... EN-2
Using the 10-key Pad (bp)...................................EN-4
Using the FUNCTION Button (
).......................EN-4
3
Getting Ready to Play................... EN-5
Preparing the Music Stand ...................................EN-5
Power Supply .......................................................EN-5
Playing the Digital Keyboard ....... EN-6
Turning on Power and Playing .............................EN-6
Using Headphones ...............................................EN-6
Changing Keyboard Response to
Touch Pressure (Touch Response)
(LK-260 only) ........................................................EN-7
Turning Off Keyboard Lighting..............................EN-7
Using the Metronome ...........................................EN-8
Controlling the
Keyboard Sounds ......................... EN-9
Select from a variety of musical
instrument sounds ................................................EN-9
Using Reverb......................................................EN-10
Using a Pedal .....................................................EN-10
Changing the Pitch (Transpose, Tuning)............EN-11
Sampling a Sound and
Playing it on the Keyboard
(Sampling) ................................... EN-12
Playing the SAMPLING DEMO ..........................EN-12
Sampling a Sound and Playing It .......................EN-12
Sounding Sampled Sounds ................................EN-14
Applying an Effect to a Sound Sample ...............EN-15
Using a Sampled Sound in a Rhythm
(VOICE PERCUSSION) .....................................EN-16
Starting a Sampling Operation Manually............EN-16
Deleting Sampled Data.......................................EN-16
Enabling or Disabling the Sampling Play Back...EN-17
Enabling or Disabling Auto Incrementing
during Short Sampling ........................................EN-17
Playing Built-in Songs.................EN-18
Playing the Demo Songs ....................................EN-18
Playing Back a Particular Song ..........................EN-18
Using Built-in Songs to
Master Keyboard Play .................EN-22
Phrases ..............................................................EN-22
Step Up Lesson Flow .........................................EN-22
Selecting the Song, Phrase,
and Part You Want to Practice ...........................EN-23
Lessons 1, 2, and 3 ............................................EN-24
Lesson Settings ..................................................EN-25
Using Auto Step Up Lesson ...............................EN-26
Using Auto Accompaniment.......EN-28
Playing the Rhythm Part only .............................EN-28
Playing All Parts .................................................EN-29
Using Auto Accompaniment Effectively ..............EN-31
Using One-Touch Preset ....................................EN-32
Connecting External Devices .....EN-33
Connecting a Computer......................................EN-33
MIDI Settings......................................................EN-34
Connecting to Audio Equipment .........................EN-36
Reference .....................................EN-37
Troubleshooting..................................................EN-37
Specifications .....................................................EN-39
Operating Precautions........................................EN-40
Song List.............................................................EN-41
Fingering Guide ..................................................EN-42
Chord Example List ............................................EN-43
MIDI Implementation Chart
English
Included Accessories
● Music Stand
● Song Book
● Leaflets
• Safety Precautions
• Appendix
• Other (Warranty, etc.)
Items included as accessories are subject to change without notice.
Separately Available Accessories
• You can get information about accessories that
are separately for this product from the CASIO
catalog available from your retailer, and from the
CASIO website at the following URL.
http://world.casio.com/
EN-1
General Guide
• In this manual, the term “Digital Keyboard” refers to the LK-170/LK-175/LK-260.
• In this manual, buttons and other controllers are identified using the numbers shown below.
1 2 34
5
6789bk bl
bm bp
bnbo
bq br bs bt ck cl
cm cn cr cscpco cq cm
EN-2
ct dk
General Guide
• The following explains the meaning of the $ symbol that appears on the product console and with the key names below.
$ : Indicates a function that is enabled by holding down the button for some time.
P(POWER) button ☞EN-6
1
VOLUME slider ☞EN-6
2
FUNCTION button ☞EN-4
3
METRONOME, $ BEAT button ☞EN-8
4
TEMPO buttons ☞EN-8, 20, 32
5
REPEAT, INTRO button ☞EN-19, 31
6
REW, NORMAL/FILL-IN button ☞EN-19, 31
7
FF, VAR./FILL-IN button ☞EN-19, 31
8
PAUSE, SYNCHRO/ENDING button ☞EN-19, 31
9
PLAY/STOP, START/STOP button ☞EN-12, 19, 28
bk
PART SELECT, ACCOMP/$ CHORDS button
bl
☞EN-21, 29
TONE, SAMPLING DEMO button ☞EN-9, 12
bm
RHYTHM, ONE TOUCH PRESET $ button
bn
☞EN-13, 28, 32
SONG BANK button ☞EN-12, 18
bo
Number buttons, [–]/[+] keys ☞EN-4
bp
SAMPLED TONES/EFFECTS 1, LISTEN button
bq
☞EN-15, 24
■ Back
dl dm
SAMPLED TONES/EFFECTS 2, WATCH button
br
☞EN-15, 24
SAMPLED TONES/EFFECTS 3,
bs
REMEMBER button ☞EN-15, 25
SAMPLED TONES/EFFECTS 4, NEXT button
bt
☞EN-15, 23
SAMPLED TONES/EFFECTS 5, AUTO button
ck
☞EN-15, 26
VOICE PERCUSSION, LESSON button ☞EN-16, 23
cl
Speakers
cm
Song Bank list
cn
Built-in microphone
co
Display
cp
SAMPLING button ☞EN-12
cq
Rhythm list
cr
Tone list
cs
CHORD root names ☞EN-29
ct
Percussion instrument list ☞EN-9
dk
dpdn do dq dr
English
USB port ☞EN-33
dl
SUSTAIN jack ☞EN-10
dm
MIC VOLUME knob ☞EN-12
dn
MIC IN/SAMPLING jack ☞EN-12
do
AUDIO IN jack (LK-260 only) ☞EN-36
dp
DC 9.5V terminal ☞EN-5
dq
PHONES/OUTPUT jack ☞EN-6, 36
dr
EN-3
General Guide
Using the 10-key Pad (bp)
Use the number buttons and the [–] and [+] keys to change
the settings of the parameters that appear in the upper left
area of the display.
Setting
Mde r nPno
Number Buttons
Use the number buttons to enter numbers and values.
• Enter the same number of digits as the currently displayed
value.
Example: To enter tone number 004, input 0 3 0 3 4.
• Negative values cannot be input using the number buttons.
Use [+] (increase) and [–] (decrease) instead.
[–] and [+] Keys
You can use the [+] (increase) and [–] (decrease) keys to
change the displayed number or value.
• Holding down either key scrolls the displayed setting.
• Pressing both keys at the same time will revert to the initial
default setting or the recommended setting.
Using the FUNCTION Button (3)
Use the FUNCTION button (
you select the reverb type, pedal effect, etc.
1.
Press 3 (FUNCTION).
) to access settings that let
3
2.
Next press 3 (FUNCTION) until the parameter
whose setting you want to change is displayed.
• Each press of 3 (FUNCTION) cycles through the
available parameters.
• To scroll backwards through parameters, hold down
(FUNCTION) as you press
Parameter Display See Page
1 Transpose Trans. EN-11
2 Accompaniment Volume AcompVol EN-32
3 Song Volume Song Vol EN-20
Touch Response
4
(LK-260 only)
5 Tuning Tune EN-11
6 Reverb Reverb EN-10
7 Voice Fingering Guide Speak EN-25
8 Note Guide NoteGuid EN-26
9 Performance Evaluation Scoring EN-26
10 Phrase PhraseLn EN-26
11 Sampling Start SampAuto EN-16
12 Sampling Play Back SampPB EN-17
Auto Incrementing during
13
Short Sampling
14 Keyboard Channel Keybd Ch EN-34
15 Navigate Channels Navi. Ch EN-34
16 Local Control Local EN-35
17 Accomp Out AcompOut EN-35
18 Pedal Effect Jack EN-10
19 Keyboard Lighting Keylight EN-7
20 Power On Alert Demo2 EN-6
3.
When the parameter you want is displayed, use
(10-key) to change its setting.
bp
• The parameter setting will disappear from the upper left
area of the screen if you do not perform any operation
for some time.
• The tone and other parameters revert to their initial
defaults whenever you turn on power (page EN-6).
(METRONOME).
4
Touch EN-7
AutoIncr EN-17
3
EN-4
Setting
Trans .
Parameter
Getting Ready to Play
Preparing the Music Stand
Music stand
Power Supply
Either an AC adaptor or batteries can be used to power this
Digital Keyboard. Normally, use of AC adaptor power is
recommended.
• The AC adaptor does not come with this Digital Keyboard.
Purchase it separately from your retailer. See page EN-1
for information about options.
Using the AC Adaptor
Make sure that you use only the AC adaptor specified for this
Digital Keyboard. Use of a different type of AC adaptor can
cause malfunction.
Specified AC Adaptor: AD-E95100L
(JEITA Standard plug)
Household power outlet DC 9.5V terminal
AC adaptor
Using Batteries
• Be sure to turn off power before loading batteries.
• It is up to you to prepare six commercially available
AA-size batteries. Do not use oxyride batteries or any
other nickel based batteries.
1.
Open the battery cover on the bottom of the
Digital Keyboard.
2.
Load six AA-size batteries into the battery
compartment.
Make sure the positive + and negative - ends of the
batteries are facing as shown in the illustration.
3.
Insert the tabs of the battery cover into the
holes on the side of the battery compartment,
and close the cover.
Tabs
English
• Be sure to turn off Digital Keyboard power before
connecting or disconnecting the AC adaptor.
• The AC adaptor will become warm to the touch after
very long use. This is normal and does not indicate
malfunction.
• To prevent breaking of the wire, take care to avoid
putting any type of load on the power cord.
No bending! No winding!
• Never insert metal, pencils, or any other objects into
the product’s 9.5V DC terminal. Doing so creates the
risk of accident.
■ Low Battery Indication
The indicator shown below starts to flash to let you know
when battery power is low. Replace the batteries with new
ones.
Low battery indicator
(flashes)
EN-5
Playing the Digital Keyboard
11 22 bmbm
Turning on Power and Playing
1.
Press 1.
This turns on power.
• To turn off the Digital Keyboard, press
2.
Try playing something on the keyboard. Use 2
to adjust volume.
4433
55
Power On Alert (Using the AC Adaptor)
While you are using the AC adaptor for power, the keyboard
keys will light to remind you that power is on if you do not
1
Increase
Decrease
again.
perform any operation for about six minutes. Power on alert is
disabled while batteries are being used for power.
■ Disabling Power On Alert
You can disable power on alert to ensure that keyboard keys
do not light during a concert, etc.
1.
Press 3 (FUNCTION) a number of times until
“Demo2” appears on the display (page EN-4).
Demo 2
• Turning off the Digital Keyboard power causes all
current settings to be cleared. The Digital Keyboard will
revert to initial default settings the next time you turn it
on.
• The message “Pls wait” will remain on the display
while a data save operation is in progress. Do not
perform any other operation while it is displayed.
Turning off the Digital Keyboard can cause Digital
Keyboard data to be deleted or become corrupted.
Auto Power Off
If you do not perform any operation on the Digital Keyboard
for one of the trigger times noted below, Auto Power Off will
turn off power.
During battery operation : 6 minutes
During AC adaptor operation: 30 minutes
■ Disabling Auto Power Off
You can disable Auto Power Off to ensure that power is not
turned off automatically during a concert, etc.
1.
While holding down bm (TONE), turn on power.
Auto Power Off will be disabled.
2.
Press the bp (10-key) [–] key to select the OFF
setting.
Using Headphones
Using headphones cuts off output from the built-in speakers,
which means you can practice playing even late at night
without disturbing others.
• Be sure to turn down the volume level before connecting
headphones.
bpbp
PHONES/OUTPUT jack
EN-6
• Headphones do not come with the Digital Keyboard.
• Use commercially available headphones. See page EN-1
for information about options.
• Do not listen to very high volume output over
headphones for long period. Doing so creates the risk
of hearing damage.
• If you are using headphones that require an adaptor
plug, make sure you do not leave the adaptor plugged
in when removing the headphones.
Playing the Digital Keyboard
Changing Touch Response Sensitivity
Use the procedure below to control how much the volume of
played notes change in accordance with playing speed.
Select the setting that best matches your playing style.
1.
Press 3 (FUNCTION) a number of times until
“Touch” appears on the display (page EN-4).
Touch
English
Changing Keyboard Response to
Touch Pressure (Touch Response)
(LK-260 only
Touch Response alters tone volume in accordance with
keyboard pressure (speed). This provides you some of the
same expressivity you get on an acoustic piano.
)
Pressing fast produces
louder notes.
Pressing slowly produces
softer notes.
Do not try to use too much
pressure.
2.
Use bp (10-key) [–] and [+] keys to select one of
the three Touch Response sensitivity settings.
Off (oFF) Touch Response is turned off. Sound
Type 1 (1) Normal Touch Response
Type 2 (2) More sensitive Touch Response than Type 1
volume is fixed, regardless of key press
speed.
Turning Off Keyboard Lighting
Keyboard Lighting causes keyboard keys to light when you
press them, during built-in song playback, etc. You can use
the following procedure to turn off Keyboard Lighting.
1.
Press 3 (FUNCTION) a number of times until
“Keylight” appears on the display (page EN-4).
Key l i gh t
2.
Press the bp (10-key) [–] key to select the OFF
setting.
EN-7
Playing the Digital Keyboard
Using the Metronome
The metronome lets you play and practice along with a steady
beat to help keep you on tempo.
Start/Stop
1.
Press 4.
This starts the metronome.
This pattern changes with each beat.
2.
Press 4 again to stop the metronome.
Changing the Beats per Measure
You can configure the metronome to use a bell sound for the
first beat of each measure of the song you are playing.
• You can specify 0, or a value from 2 to 6 as the number of
beat per measure.
• When playing a built-in song, the beats per measure setting
(which determines when the bell sounds) is configured
automatically for the currently selected song.
1.
Hold down 4 until the beats per measure
setting screen appears on the display.
Bea t
• If you do not perform any operation for after the beats
per measure setting screen appears, the display will
return to the screen displayed before you pressed
2.
Use bp (10-key) to enter the number of beats
per measure.
• The bell will not sound if you specify 0 for this setting. In
this case, all beats are indicated by a click sound. This
setting lets you practice with a steady beat, without
worrying how many beats there are in each measure.
4
Changing the Metronome Tempo
Use the following procedure to change the tempo of the
metronome.
1.
Press 5.
Use w (slower) and q (faster) to change the tempo
setting. Holding down either button changes the setting at
high speed.
• Pressing w and q at the same time will initialize the
tempo setting in accordance with the currently selected
song or rhythm.
• Pressing
display. While the tempo value is flashing, you can use
bp
Note that you must input leading zeros, so 89 is input
as 089.
• The tempo value will stop flashing if you do not perform
any operation for a short while.
Tempo value (flashes)
causes the tempo value to flash on the
5
(10-key) to change it.
Changing the Metronome Sound Volume
The metronome volume setting is changed automatically with
the volume level of the currently selected Auto
Accompaniment or song. The metronome volume cannot be
adjusted independently.
• For information about changing the Auto Accompaniment
volume, see page EN-32.
• For information about changing the song volume, see page
EN-20.
• You cannot adjust the balance between the metronome
and note volume during Auto Accompaniment and built-in
tune play.
.
EN-8
Controlling the Keyboard Sounds
33
Select from a variety of musical
instrument sounds
Your Digital Keyboard lets you select tones for a wide variety
of musical instrument sounds, including violin, flute, orchestra,
and more. Even the same song sound takes on a different feel
by changing the instrument type.
To select an instrument for playing
1.
Press bm (TONE).
Tone number
St .GrPno
Tone name
2.
Use bp (10-key) to select the tone number you
want.
The corresponding tone number and tone name will
appear on the screen.
• Use the number buttons to enter the tone number.
Specify three digits for the tone number.
Example: To select 001, enter 0 3 0 3 1.
bnbn
bmbm
3.
Try playing something on the keyboard.
The tone of the instrument you selected will sound.
bpbp
Playing with a Piano Tone (Piano Setup)
Press
(TONE) and bn (RHYTHM) at the same time.
bm
This selects the grand piano tone.
Settings
Tone Number: “001”
Reverb: “06”
Transpose: “00”
Touch Response (LK-260 only):
Pedal Effect: SUS
Rhythm Number: “131”
Accompaniment: Rhythm part only
Local Control: On
Voice Percussion: Off
Off: Returns to initial default
On: No change
English
• See the separate “Appendix” for a complete list of available
tones.
• When one of the drum sets is selected (tone numbers 395
through 400), each keyboard key is assigned a different
percussion sound.
EN-9
Controlling the Keyboard Sounds
Using Reverb
Reverb adds reverberation to notes. You can change the
duration of the reverb.
1.
Press 3 (FUNCTION) a number of times until
“Reverb” appears on the display (page EN-4).
Reverb
2.
Use the bp (10-key) [–] and [+] keys to select
the reverb setting you want.
Off (oFF) Turns off reverb.
1 to 10 The larger the number selected, the longer
the reverb duration.
Reverb
Indicator disappears when
reverb is turned off.
Using a Pedal
A pedal can be used to change notes in various ways while
playing.
• A pedal unit does not come with the Digital Keyboard.
Purchase one separately from your retailer. See page EN-1
for information about options.
Connecting a Pedal Unit
Connect an optional pedal unit.
SUSTAIN jack
Selecting the Pedal Effect
1.
Press 3 (FUNCTION) a number of times until
“Jack” appears on the display (page EN-4).
Jack
2.
Use the bp (10-key) [–] and [+] keys to select
the pedal effect you want.
• The following shows the available pedal effects.
Sustain
(SUS)
Sostenuto
(SoS)
Soft
(SFt)
Rhythm
(rHy)
Sustains notes played while the pedal is
depressed. Organ and other similar tone
notes are sustained even if the pedal is not
pressed.
Sustains notes that are playing when the
pedal is depressed before the keyboard
keys are released.
Slightly softens notes played while the pedal
is depressed.
Pressing the pedal starts and stops Auto
Accompaniment or song playback.
EN-10
Changing the Pitch
(Transpose, Tuning)
Controlling the Keyboard Sounds
Changing the Pitch in Semitone Steps
(Transpose)
The transpose feature lets you change the pitch, in semitone
steps. A simple operation lets you instantly change the pitch
to match that of a singer.
• The transpose setting range is –12 to +12 semitones.
1.
Press 3 (FUNCTION).
Trans .
2.
Use the bp (10-key) [–] and [+] keys to select
the transpose setting you want.
Fine Tuning (Tuning)
Use the tuning feature when you need to adjust the pitch
slightly to play along with another musical instrument. Also,
some artists perform their music with slightly altered tuning.
You can use the tuning feature to adjust tuning so it exactly
matches a performance on a CD.
• The tuning feature specifies the frequency of the A4 note.
You can set a frequency within the range of 415.5 to
465.9 Hz. The initial default setting is 440.0 Hz.
1.
Press 3 (FUNCTION) a number of times until
“Tune” appears on the display (page EN-4).
English
Tune
2.
Use the bp (10-key) [–] and [+] keys to adjust
the tuning.
• Performing this step causes the display to change from
“Tune” to a value that indicates the current frequency
setting as shown below. You can change the frequency
in 0.1Hz steps.
440.0Hz
• Even if you do not perform a
adjust the tuning, the current frequency setting will
appear automatically after a few seconds.
(10-key) operation to
bp
EN-11
Sampling a Sound and Playing it on the Keyboard
(Sampling)
11 cqcq
33
bmbm
bnbn
bobo
bpbp
bkbk
You can use the digital keyboard’s built-in microphone to
record a sound and then play it with the keyboard keys. The
sampling feature is a great way to create your own original
sounds.
Connecting a Microphone
Connect a microphone. When connecting a microphone, be
sure to first adjust the MIC VOLUME knob to a low setting.
Keyboard jack connector : Standard plug (monaural)
MIC IN/SAMPLING jack
• Use of a commercially available microphone also is
supported.
• Turn off the microphone and the Digital Keyboard
before connecting them.
• It will take a few seconds before you can use the
microphone after you turn on the Digital Keyboard.
• Sampled sounds are recorded in monaural.
• The built-in microphone is only for inputting and
recording external sounds for use with the sampling
function. Sounds input with the built-in microphone are
not output through the speakers.
• You cannot sample sounds input from through the
AUDIO IN jack.
• The built-in microphone automatically becomes
disabled whenever an external microphone is
connected to the MIC IN/SAMPLING jack.
bqbq brbr bsbs btbt ckck clcl
Playing the SAMPLING DEMO
Use the procedure below to play a demo tune that features
sampled sounds.
1.
Hold down bm (SAMPLING DEMO).
This starts playback.
2.
To stop demo play, press bm or bk.
Sampling a Sound and Playing It
There are two sampling methods: long sampling and short
sampling. Long sampling is used for sampling in the Song
Bank Mode, while short sampling is use for sampling in the
Rhythm Mode.
■ Long Sampling
This method allows sampling of a single sound with a duration
of two seconds.
• Sampling a new sound overwrites all previously
recorded data (including data recorded with short
sampling).
1.
Press bo (SONG BANK).
EN-12
2.
Press cq (SAMPLING) and release it.
This enters sampling standby.
Speak !
Flashes
3.
Produce the desired sound in the direction of
the built-in microphone.
Sampling will start automatically.
Samp l i n g
Sampling a Sound and Playing it on the Keyboard (Sampling)
■ Short Sampling
With short sampling, you can record up to five samples, each
with a length of up to approximately 0.4 seconds. Short
samples are assigned rhythm parts, and can be sounded as
voice percussion. For details, see “Using a Sampled Sound in
a Rhythm (VOICE PERCUSSION)” (page EN-16).
• Sampling a new sound overwrites all previously
recorded data (including data recorded with long
sampling).
1.
Press bn (RHYTHM).
• If you want to use a rhythm for sampling, select it here.
2.
Press cq (SAMPLING) and release it.
This enters sampling standby.
• At this time tone number 412 (which is short sampling 1
tone) is selected.
Speak !
English
• Sampling will not start if the volume level of the sound
being sampled with the microphone is too low.
• Sampling will stop automatically two seconds after it
starts, or if the sound being input through the
microphone stops before then.
Flashes
• Random phrases using the sampled sound will play
back to indicate that sampling is complete.
• What you sample is stored as tone number 401.
4.
Press a keyboard key.
This will play the recorded sound.
Flashes
3.
Produce the desired sound in the direction of
the built-in microphone.
Sampling will start automatically.
Samp l i n g
• Sampling will not start if the volume level of the sound
being sampled with the microphone is too low.
• Sampling will stop automatically 0.4 seconds after it is
started.
EN-13
Loading...