PAGE
TABLE OF CONTENTS
INITIAL SETUP
Important Safety
Instructions.................... 2
Connecting your Unit......... 3
Charging the Batteries ....... 4
Switch Settings.................. 4
Tone/Pulse Service......... 4
Base Ringer On/Off ........ 4
Base Speaker Volume ........ 4
Important Feature
Information .................... 5
Programming the Handset
Ringer Volume & Tone ... 5
CORDLESS OPERATION
Standby Mode ................... 6
Placing a Call ..................... 6
Misdialing a Number.......... 6
Answering a Call ................ 6
Adjusting the Handset
Earpiece Volume ............ 6
Switching from Handset to
Speakerphone ................ 7
Status Indicator ................. 7
Low Battery Indicator ........ 7
Out of Range Alarm ........... 7
BASE OPERATION
Maximizing the Benefits of
the Speakerphone .......... 8
Placing a Call ..................... 8
Misdialing a Number.......... 8
Answering a Call ................ 8
Placing a Call On Hold ....... 9
Taking a Call Off Hold ........ 9
Mute .................................. 9
Switching from
Speakerphone to
Handset.......................... 9
PAGE/INTERCOM
Paging the Handset from
the Base Unit................ 10
Using the Intercom from
the Base Unit................ 10
Using the Intercom from
the Handset.................. 10
Answering a Call While
Using the Intercom ...... 11
Room Monitor ................. 11
3-WAY CONFERENCE
3-Way Conference Initiated
from Handset ............... 12
3-Way Conference Initiated
from Base .................... 12
AUTODIAL
Storing Autodial Numbers
into the Handset........... 13
Erasing Autodial Numbers
from the Handset ......... 13
Storing Autodial Numbers
into the Base Keypad.... 14
Erasing Autodial Numbers
from the Base............... 14
Using Autodial from the
Handset........................ 14
Dedicated One Touch
Autodial Buttons .......... 15
Using Autodial from the
Base ............................. 15
Programming Autodial
Pauses ......................... 16
Programming T one/Pulse
in Autodial ................... 1 6
1
ADDITIONAL
INFORMATION
Flash/Call Waiting ............ 17
Redialing ......................... 17
T one/Pulse Mixed Dialing. 17
Moving the CP-1260........ 18
T wo-Line Installation ....... 18
Multi-Line Installation...... 18
Cleaning the CP-1260...... 18
Changing the Digital
Security Code............... 18
Handset Battery
Installation ................... 19
Wall Mounting ................. 20
T r oubleshooting............... 21
Questions? Here’s How
to Reach Us ................. 22
Limited Warranty............. 23
FCC Requirements ........... 24
Accessories ..................... 25
PAGE
IMPORTANT SAFETY
2
INSTRUCTIONS
INSTALLATION
PAGE
3
INSTALLATION INSTRUCTIONS
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the
network interface.
4. Use caution when installing or modifying telephone lines.
SAFETY PRECAUTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
4. Do not use this product near water: for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in
a wet basement, or near a swimming pool.
5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious product
damage.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from
overheating, these openings must not be blocked or covered by placing the product on the bed, sofa, rug, or
other similar surface. This product should never be placed near or over a radiator or heat register. This
product should not be placed in an enclosed environment unless proper ventilation is provided.
7. Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by
animals or persons walking on it.
8. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a risk of fire or electric shock.
10. Never spill liquid of any kind on the product.
11. To reduce the risk of electric shock, do not disassemble this product. Take it to a qualified service person
when service or repair work is required. Opening or removing covers may expose you to dangerous voltages
or other risks. Incorrect re-assembly can cause electric shock when the appliance is subsequently used.
12. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions because improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk
of electric shock from lightning.
14. Do not use the telephone to report a gas leak while near the leak.
15. You should use ONLY the power adapter supplied with the unit. If you need a replacement, please see
ACCESSORIES on page 25 to place an order.
SAVE THESE INSTRUCTIONS
CONNECTING YOUR UNIT
Install the handset battery. See page 19,
1
“HANDSET BATTERY INSTALLATION.”
PLUG
the CP-1260’s telephone cord into a
telephone wall jack.
2
the cord into the back of the base unit.
CONNECT
of the unit.
3
underside of the unit) to prevent accidental disconnection.
PLUG
electrical wall outlet.
4
It may be necessary to set the TONE/
PULSE SWITCH (see page 4).
5
Raise the charging cradle antenna for
clear reception.
6
Place the handset (with battery pack
installed) in the cradle and charge for
7
12-15 hours.
NOTES:
■ Place the power cord so it does not create a trip hazard, or where it could become chafed and create a fire or electrical
hazard.
■ Use only the supplied AC Adapter, do not use any other AC adapters.
the AC Adapter Plug into the DC IN 9V jack on the back
ROUTE
the AC Adapter into an
PLUG
the other end of
the cord around the strain relief latch (on the
PAGE
PAGE
BATTERIES & SWITCH SETTINGS
4
CHARGING THE BATTERIES
Charge the batteries for 12-15 hours before
using the cordless handset for the first time.
The handset is always charging while it is in
the base unit and cannot be overcharged.
From fully charged, you should get 7 hours
continuous use and 14 days use when the
handset is in the standby mode (charging in
the base).
Check the AC Adapter to see that it is
connected correctly to the base unit
1
and wall outlet.
Place the handset in the base CP-1260
face up or face down. Make sure that
2
the STATUS INDICATOR on the base
unit is lit to indicate that the
CP-1260 is charging.
NOTES:
■ The battery pack will gradually discharge over a
long period of time even when it is not being used.
For the best performance, return the handset to the
base unit after each telephone call to charge the
battery.
■ If you must replace the battery pack during a
telephone call, complete the replacement of the
battery pack within 30 seconds, and you can return
to the original call.
SWITCH SETTINGS
The CP-1260 has two switches. The TONE/
PULSE SWITCH and BASE RINGER ON/OFF
SWITCH are on the back side of the base
CP-1260.
TONE/PULSE SERVICE
The TONE/PULSE SWITCH (on the back side
of the base unit) configures the unit to dial out
with either touchtone or pulse signals to
match the service supplied by your local
telephone company. The CP-1260 is shipped
with the TONE/PULSE SWITCH in the TONE
position for touchtone service. If you have
rotary or pulse service, set this switch to
PULSE.
PULSE = for Rotary dialing or Pulse
services
TONE = for T ouchtone service
BASE RINGER ON/OFF
The CP-1260 is shipped with the base ringer
ON/OFF SWITCH set to “ON.” To turn the
base ringer OFF, move the switch (located on
the left side of the CP-1260) to the “OFF”
position.
FEATURES & PROGRAMMING
IMPORTANT FEATURE
INFORMATION
The CP-1260 features include AutoTalk™ and
AutoStandby™ . AutoTalk allows you to
answer a call by just removing the handset
from the base so you don’t have to waste
time pushing buttons or flipping switches.
AutoStandby allows you to hang up by
simply returning the handset to the base.
The Ultra Clear
virtually eliminates background noise. This
innovative technology provides you with the
best possible reception during all your
conversations.
To protect you against misbilled calls which
might result from your phone being activated
by other equipment, the CP-1260 has Random
Code™ digital security which automatically
selects one of over 65,000 digital security
codes for the handset and base. Also, the
AutoSecure™ feature electronically locks your
phone when the handset is on the base.
AUTOMATIC DIGITAL SECURITY
CODE
This identification code is used to connect the
handset and the base unit. It protects
communication between the handset and
base, preventing unauthorized access to your
base unit, so that other cordless handsets
cannot make calls through your base unit. A
random digital security code is automatically
assigned out of 65,000 codes, the first time
you charge the handset in the base. If you
need to reset the security code, see page 18.
®
Noise Reduction Circuit
The handset ringer can be programmed to
ring with one of four ringer selections. There
are two distinct ringer tones in the handset
and each ringer tone has two different volume
levels.
PROGRAMMING
THE HANDSET RINGER
VOLUME AND TONE
In the standby mode, press
1
Each time
ringer tone setting changes and the
2
handset will ring for two seconds
with the chosen ringer tone to verify
your choice.
The handset will now use this ringer
tone and volume whenever it rings.
3
VOLUME
is pressed, the
5
VOLUME
.
BASE SPEAKER VOLUME
To control the speaker volume of the base,
adjust the VOLUME slide switch as desired.
Auto Talk, Auto Standby, Random Code, and Auto Secure are
proprietary trademarks of Uniden America Corporation.
PAGE
PAGE
6
CORDLESS TELEPHONE OPER
STANDBY MODE
The CP-1260 is in standby mode whenever it
is idle, waiting for a call. It is not necessary
to press TALK to disconnect the call. When
the handset is in talk mode and returned to
the base, it will automatically disconnect the
call and return to standby mode. You may
place the handset face up or face down in the
charging cradle to disconnect the call and
charge the handset.
PLACING A CALL
Pick up the handset and press
TALK
1
2
3
NOTE:
■ The STATUS INDICATOR on the base will light solid to
show that the CP-1260 is in use.
. The TALK/BATT LOW
INDICATOR will light.
Wait for a dial tone and then dial the
phone number . The phone number
dialed can be up to 32 digits.
TALK
To hang up, press
handset to the base unit. The CP-1260
is now ready to answer a call. If you
put the handset in the base the
STATUS INDICATOR lights to show
the battery is charging.
or return the
MISDIALING A NUMBER
Press
TALK
twice (“off” and “on.”)
Wait for the dial tone and then dial the
1
correct number .
ANSWERING A CALL
If the cordless handset is out of the
charging cradle when the phone
1
rings, pick it up and press
the cordless handset is in the cradle,
pick it up (
to the caller .
To hang up, press
handset or return the handset to the
2
base unit.
do not press
TALK
TALK
TALK
). Speak
on the
. If
ADJUSTING THE HANDSET
EARPIECE VOLUME
There are three handset conversation volume
levels.
Press
VOLUME
level of the handset during a
1
conversation. The volume control
automatically stays at the selected
setting after each phone call.
NOTE:
■ When the CP-1260 is in standby mode, press
VOLUME
volume level (see page 5).
to change the ringer tone and ringer
to adjust the sound
SWITCHING FROM
A TION
SWITCHING FROM
HANDSET TO
SPEAKERPHONE
To switch from the cordless handset to the
speakerphone:
Press
INT’COM
while speaking on the handset to
1
place the call on hold. The STATUS
INDICATOR will flash on the base.
The intercom tone sounds on the
handset and base.
INTERCOM
Press
SPEAKERPHONE
2
The intercom mode is activated, but
the caller is still on hold.
To transfer to the base, press
on the handset. To cancel the
3
transfer, press
on the base.
STATUS INDICATOR
The STATUS INDICATOR (located on the base
unit) will light green whenever the handset is
in talk mode. It will also light when the
handset is actively charging in the base unit.
Place the handset face up or face down in the
charger for 12-15 hours before the first use
and after installing the handset battery or
when the BATT LOW INDICATOR flashes.
OUT OF RANGE ALARM
on the handset
or
on the base.
TALK
SPEAKERPHONE
7
LOW BATTERY INDICATOR
When the handset battery pack needs
recharging, the BATT LOW INDICATOR blinks.
If the phone is in use, the handset beeps. You
may also notice a reduction in the quality of
your cordless handset communications.
Return the cordless handset to the charging
cradle.
NOTE:
■ The batteries can be recharged many times, but if
you get a low battery indication even after 12-15
hours of charging, you should replace the battery
pack.
OUT OF RANGE ALARM
1. The CP-1260 cordless handset operates
like any other telephone handset. You can
use it in the yard, at the mailbox, or any
place within the operating range of the
base. If you move out of the base unit’s
operating range, you will hear a warning
tone. Move closer to the base unit to
deactivate the alarm. If you remain out of
range for too long, the CP-1260 will
disconnect from the line.
2. If the handset loses its security code, you
will also hear an alarm tone. See page 18
to reset this security code. Pick up the
handset and try your call again.
3. Interference from other appliances may
also cause the alarm to sound. To prevent
interference, move the base unit to another
location and orient the base unit antenna
to a vertical position.
BASE
PAGE
PAGE
OPERATION
8
MAXIMIZING THE BENEFITS
OF THE SPEAKERPHONE
■ One person at a time should speak while
using the speakerphone.
■ Reduce or eliminate background noise
such as the radio or television.
■ The extension phone and speakerphone
should not be used at the same time
unless you require a 3-way conference
with the caller.
■ Position yourself approximately 12 inches
away from the base microphone (located
at the front under the base) and speak
clearly.
PLACING A CALL
Press
1
2
3
NOTES:
■ The SPEAKERPHONE INDICATOR on the base will
light to show that the CP-1260 is in use.
■ If you pick up the handset during a call with the
base, the call is switched to the handset.
SPEAKERPHONE
Wait for a dial tone and then dial the
phone number. The phone number
dialed can be up to 32 digits.
To hang up, press
SPEAKERPHONE
is now ready to answer a call.
.
. The CP-1260
MISDIALING A NUMBER
Press
SPEAKERPHONE
(“off” and “on.”) Wait for the dial tone
1
and then dial the correct number.
twice
ANSWERING A CALL
The speakerphone allows you to conduct
phone conversations without using the
handset.
If you decide to answer the call using the
base speakerphone:
SPEAKERPHONE
Press
.
1
Adjust the
(on the right side of the base) if
2
necessary.
Speak into the microphone (located
at the front under the base unit). You
3
will hear the outside party through the
speaker. (If you wish to speak
through the cordless handset, first
press
pick up the handset from the cradle.
If the handset is already out of the
cradle press
To hang up from the base, press
SPEAKERPHONE
4
VOLUME CONTROL
HOLD
on the base unit, then
TALK
.)
.
PLACING A CALL ON HOLD
Press
HOLD
on the base unit. The
HOLD INDICATOR will light.
1
TAKING A CALL OFF HOLD
There are a few ways to take a call off hold.
Press
SPEAKERPHONE
on the base again. The
1
SPEAKERPHONE INDICATOR will light
and the call will be taken off hold.
OR
Take the handset out of the base. The
call will now be connected to the
1
handset user only.
or
HOLD
MUTE
You can turn off the base microphone.
Press
MUTE
during a telephone call
to turn off the microphone. The
1
SPEAKERPHONE INDICATOR flashes
slowly.
To cancel mute, press
SPEAKERPHONE
2
MUTE
.
or
SWITCHING FROM
SPEAKERPHONE TO
HANDSET
To switch from the speakerphone to the
cordless handset:
Press
INTERCOM
speaking on the speakerphone to
1
place the call on hold. The STATUS
INDICATOR will flash. The intercom
tone sounds on the handset and base.
Press
INT’COM
handset. The intercom mode is
2
activated, but the caller is still on hold.
To transfer to the handset, press
SPEAKERPHONE
3
To cancel the transfer, press
on the handset.
on the base while
or
TALK
on the
on the base.
TALK
9
PAGE
PAGE
10
PAGE/INTERCOM
PAGING THE HANDSET
FROM THE BASE UNIT
To page the handset from the base
unit, in standby mode, press
1
INTERCOM
will hear the handset and base beep.
Move away from the base unit to
locate the handset.
To cancel the page, press
INTERCOM
2
wait for the paging tone to stop within
60 seconds.
on the base unit. You
on the base or simply
USING THE INTERCOM
FROM THE BASE UNIT
You may conduct a private conversation with
the handset user by using intercom.
Press
INTERCOM
to send a paging signal to the handset.
1
The handset will beep intermittently
for 60 seconds. The STATUS
INDICATOR on the base will blink.
When the handset user presses
INT’COM
2
the base unit will be connected.
or
on the base unit
TALK
, the handset and
To terminate the intercom call, press
TALK
3
on the handset or
SPEAKERPHONE
on the base unit.
USING THE INTERCOM
FROM THE HANDSET
In the standby mode, press
INT’COM
1
the base unit user. Both the handset
and base will beep.
When the base user presses
INTERCOM
2
the handset and the base unit will be
connected.
Press
SPEAKERPHONE
3
terminate the intercom mode.
NOTES:
■ Intercom can also be activated during a
conversation to allow the handset user and base
user to speak privately while the caller is on hold.
■ To activate a 3-way conference call between the
caller, the handset user and the base
speakerphone user during an active call, see “3WAY CONFERENCE” on page 12.
■ You can attempt an intercom connection for
maximum 1 minute. It stops if no one answers.
to send a paging signal to
or
SPEAKERPHONE
TALK
on the handset or
on the base to
11
ANSWERING A CALL WHILE
USING THE INTERCOM
If you receive an incoming call during an
intercom conversation you will hear a ring
through the base speaker.
Press
SPEAKERPHONE
the intercom conversation and press
1
SPEAKERPHONE
the incoming call. The handset is
automatically disconnected from the
intercom.
,
Speak to the caller.
to hang up
again to answer
You can call your base unit from the handset
and monitor sounds in the room where your
base unit is installed.
2
SPEAKERPHONE
Press
hang up.
3
OR
Press
TALK
on the handset to hang
up the intercom conversation and
1
TALK
press
incoming call with the handset. The
base unit is automatically
disconnected from the intercom.
Speak to the caller.
again to answer the
again to
ROOM MONITOR
INT’COM
Press
The handset beeps.
1
TALK
Press
room where your base unit is
2
installed.
To finish the room monitor, press
TALK
3
again.
on the handset.
. You hear sounds in the
2
3
Press
TALK
again to hang up.
PAGE
PAGE
12
3-WA Y CONFERENCE
3-WAY CONFERENCE
INITIATED FROM HANDSET
You may conduct a conversation with an
outside caller using the intercom between the
handset and the base speakerphone. For
example:
While talking on the handset with an
outside caller, press
1
SPEAKERPHONE
The call automatically becomes a
3-way conference.
2
To return to the conversation
between the handset and the outside
3
line, press
the base.
NOTE:
■ Dialing is possible only from the handset during
3-way conversation.
SPEAKERPHONE
on the base.
on
3-WAY CONFERENCE
INITIATED FROM BASE
You may conduct a conversation with an
outside caller using the intercom between the
handset and the base speakerphone when the
handset is off the base. For example:
While talking on the base with an
TALK
outside caller, press
1
handset.
The call automatically becomes a
3-way conference.
2
To return to the conversation
3
between the base and the outside
TALK
line, press
NOTES:
■ Pressing
■ Dialing is possible only from the handset during
TALK
way conversation mode while in the process of
dialing with the base.
3-way conversation.
on the handset will not set the 3-
on the handset.
on the
AUTODIAL
STORING AUTODIAL
NUMBERS INTO THE
HANDSET
You may store up to 20 of your most
frequently dialed numbers in autodial
memory (10 in the handset and 10 in the
base). The base unit must be connected to
the electrical wall outlet with the AC adapter.
The phone must be in the standby mode to
store an autodial number.
Press
MEM
on the handset. The
TALK/BA TT LOW INDICATOR will
1
flash slowly.
Enter the telephone number you wish
to store using the handset keypad.
2
Autodial phone numbers can be up to
16-digits each. Use
you want to insert a pause in your
autodial number.
MEM
Press
REDIAL/P
again.
if
3
Enter an autodial location using the
handset keypad (0 to 9). A long
4
confirmation beep indicates the
number has been stored.
13
Continue storing autodial numbers by
repeating steps 1-4.
5
NOTES:
■ If you do not press a key within 20 seconds, the
CP-1260 will exit the programming mode.
■ If you return the handset to the cradle, the phone
will return to standby.
■ You cannot store phone numbers directly into the
dedicated one-touch autodial keys. See
“DEDICATED ONE TOUCH AUTODIAL BUTTONS”
on page 15 for one touch dialing.
ERASING AUTODIAL
NUMBERS FROM THE
HANDSET
Press
MEM
twice.
1
Enter the memory location number
(0-9) of the number you wish to
2
delete. A long confirmation tone
indicates the memory has been
erased.
PAGE
PAGE
14
AUTODIAL (cont.)
STORING AUTODIAL
NUMBERS INTO THE BASE
KEYPAD
You may store up to 20 of your most
frequently dialed numbers in autodial
memory (10 in the handset and 10 in the
base). The base unit must be connected to
the electrical wall outlet with the AC adapter.
The phone must be in the standby mode to
store an autodial number.
MEM
Press
STA TUS INDICA TOR flashes slowly.
1
Enter the telephone number you
want to store using the base keypad.
2
Use
PAUSE
pause in your autodial number.
Press
on the base. The
if you want to insert a
MEM
again.
3
Enter an autodial location using the
base keypad (0-9). The STATUS
4
INDICATOR turns off. A long
confirmation beep indicates the
number has been stored.
Continue storing autodial numbers
by repeating steps 1-4.
5
NOTE:
■ If you do not press a key within 20 seconds, the
CP-1260 will exit the programming mode.
ERASING AUTODIAL
NUMBERS FROM THE BASE
Press
MEM
on the base. The
STATUS INDICATOR flashes slowly .
1
Press
MEM
again.
2
Enter the memory location number
(0-9) of the number you wish to
3
delete. The STATUS INDICATOR
stops flashing. A long confirmation
beep indicates the number has been
erased.
USING AUTODIAL FROM
THE HANDSET
Press
TALK
.
1
Press
MEM
on the handset.
2
Use the handset keypad to enter the
number (0-9) corresponding to the
3
autodial location you wish to call. For
example, if the number of the person
you are calling is stored in autodial 6,
6
. The CP-1260 will
press
automatically dial out.
To hang up, press
handset to the base.
4
NOTE:
■ You must press a key within 20 seconds or the phone
will return to standby.
DEDICATED ONE TOUCH
AUTODIAL BUTTONS
Your phone is equipped with three instant
dialing buttons (M1-M3) on the handset. You
cannot store phone numbers directly into M1
to M3. These are only used to dial phone
numbers stored in handset memory locations
1-3.
Press M1,
pressing TALK.
1
M2
or
TALK
M3
or return the
to dial without
USING AUTODIAL FROM
THE BASE
Press
SPEAKERPHONE
.
1
MEM
Press
on the base.
2
Use the base keypad to enter the
number (0-9) corresponding to the
3
autodial location you wish to call.
For example, if you know that the
number of the person you are calling
6
is stored in autodial 6, press
CP-1260 will automatically dial out
using the speakerphone.
To hang up, press
SPEAKERPHONE
4
.
. The
15
PAGE
PAGE
16
AUTODIAL (cont.)
PROGRAMMING
AUTODIAL PAUSES
Pause is convenient for use on a business
telephone system (i.e.; PBX) when an 8 or 9
must be dialed to reach an outside phone
line. This feature can also be used for a long
distance service (i.e.; Sprint, MCI) where you
have to wait for a second dial tone before you
continue dialing.
Follow instructions for storing
autodial numbers on pages 13 and 14.
1
While storing autodial numbers, press
REDIAL/P
2
in the base after entering an outside
access digit or other number when a
pause is required. Each pause is two
seconds in length and counts as one
digit in the autodial memory.
Example: 9 P 1 2 1 3 5 5 5 1 2 1 2
in the handset or
PAUSE
PROGRAMMING TONE/
PULSE IN AUTODIAL
You may store frequently dialed mixed tone/
pulse numbers in the autodial memory. This
will work when you have the TONE/PULSE
SWITCH on the base CP-1260 set to PULSE.
Follow instructions for storing autodial
numbers on pages 13 and 14.
1
During autodial programming, press
TONE
2
following portion of the phone
number needs to be switched from
pulse to tone.
Example: 555-1212❋3457
❋❋
(
on the keypad) when the
❋
❋❋
(pulse) (tone)
ADDITIONAL INFORMA TION
NOTES:
FLASH/CALL WAITING
If you subscribe to a call waiting service and
you receive another call while using the
phone or speakerphone, press
the handset or base to answer the second
call. To return to the first call, press
again. You may switch between the two calls
until a caller hangs up.
FLASH may also be used on a business phone
system (CENTREX, PBX) for transferring calls.
NOTE:
■ Pressing
TALK
SPEAKERPHONE
call with either party will disconnect both parties.
while on the handset or
while on the base during an active
FLASH
on
FLASH
REDIALING
The CP-1260 remembers the last number you
dialed. The redial memory will hold up to 32
digits. Every time you dial a new telephone
number, the redial memory is updated with
that new number.
Press
TALK
or
SPEAKERPHONE
and wait for a dial tone.
1
Press
REDIAL
.
■ If the recently dialed number exceeds 32 digits,
only the first 32 digits are retained for redialing.
■ The handset and base store redial information
separately. The last call made using the handset
will be stored in the handset and the last call made
using the base will be stored in the base.
TONE/PULSE MIXED
DIALING
Tone/pulse mixed dialing can only be used in
areas with pulse dialing service. The CP-1260
should be set to PULSE. If you live in a pulse
or rotary dialing area, you can use TONE to
access a long distance service (i.e., Sprint or
MCI), bank by phone or any other service that
requires touchtone dialing.
Dial a local telephone number in pulse
mode and wait for the line to connect.
1
TONE
Press
temporarily change from pulse to
2
tone mode after the line is connected.
Dial the tone numbers. This could be a
special service or access number.
3
Hang up and the CP-1260 will
automatically return to the pulse mode.
4
❋❋
(
on the keypad) to
❋
❋❋
2
17
The last number dialed will be
redialed.
3
PAGE
PAGE
18
ADDITIONAL INFORMATION
MOVING THE CP-1260
Unplug the CP-1260 from the wall outlet if
you wish to move the CP-1260. Place the
handset in the charging cradle after relocating
the CP-1260. All autodial numbers will be
saved.
TWO-LINE INSTALLATION
Two-line installations may require a two-line
T-adapter for the CP-1260 to operate correctly.
The T-adapter allows you to connect your
machine to Line 1 or Line 2. The
CP-1260 will only operate on one line.
(See “ACCESSORIES” page 25.)
MULTI-LINE INSTALLATION
Installations with more than two lines, such
as business PBX or Key Systems, may require
a separate RJ11 jack. Please contact your
telephone equipment provider for additional
information. (See “ACCESSORIES” page 25.)
CLEANING THE CP-1260
CAUTION: Disconnect the CP-1260 from the
power outlet before cleaning.
Use a damp cloth or moist sponge to clean:
1. The antenna.
2. The plastic cabinet of the handset and
base.
3. The battery charging contacts on the
handset and base.
A mild soap, like dishwashing detergent, will
help remove grease or oil. Do not spray
cleaners directly onto the CP-1260. Cleaners
should only be used on the plastic surfaces.
Thoroughly dry all parts of the handset and
charging cradle before re-using.
CHANGING THE DIGITAL
SECURITY CODE
The digital security code is an identification
code to connects the handset and the base
unit. The security code is automatically set
the first time you charge the handset in the
base (see page 5). It is usually unnecessary
to reset this code. However, if another
cordless telephone appears to be using the
same code, you can change it.
Place the handset in the cradle.
INTERCOM
Press
1
Remove the handset from the cradle
for at least 1 second, and place it back
2
in the cradle. Leave the handset in the
base for at least 4 seconds. A new,
random security code is set.
NOTE:
■ The digital security code is lost if the handset
battery pack is completely discharged or the
battery pack is removed. If this happens, a new
security code is set automatically the next time the
handset is charged in the cradle.
on the base.
HANDSET BATTERY
INSTALLATION
THIS CP-1260 IS NOT SHIPPED WITH
THE HANDSET BATTERY PACK
INSTALLED - INSERT HANDSET
BATTERY BEFORE INITIAL SETUP
AND USE.
To install or replace the battery pack:
Press down on the battery
compartment cover and slide it
1
toward the bottom of the handset.
(Remove old battery pack if you are
replacing a battery.)
Install the new battery pack with the
red wire below the black wire (see
2
drawing below).
Replace the battery cover by sliding it
up from the bottom.
3
Place the handset in the base unit
cradle face up or face down and charge
4
the battery pack for 12-15 hours.
WARNING:
Use only Ni-Cd Rechargeable
Battery Pack
(3.6 volts 600 mAh.)
NOTE:
■ Make sure that the wire is not caught in between
the battery cover.
RECYCLING NICKEL-CADMIUM BATTERIES
NICKLE-CADMIUM BATTERIES
MUST BE DISPOSED OF
PROPERLY.
Nickel-cadmium cells are used in
the battery pack. Please take
your nickel-cadmium battery
packs to a store that recycles
nickel-cadmium batteries.
19
PAGE
PAGE
20
WALL MOUNTING TROUBLESHOOTING
WALL MOUNTING
The CP-1260 can be wall mounted easily by
following these instructions.
If you have a standard wall plate, skip
this step. If you don’t have a standard
1
wall plate, mount the phone directly to
the wall. Insert two mounting screws
into the wall (not included), 3-15/16
inches apart. Allow about 3/16 of an
inch between the wall and screwheads
for mounting the phone.
Snap the wall mount bracket into the
notches on the base.
2
Plug the telephone line cord into the
TEL LINE jack and the AC Adapter into
3
the DC IN 9V jack.
Plug the telephone line cord into the
telephone outlet.
4
Wrap the AC adapter cord inside the
molded wiring channel. Then wrap the
5
cord around the strain relief notch
located at the underside of the base.
Plug the AC adapter into the electrical
wall outlet.
6
Raise the antenna to a vertical position.
7
Align the mounting slots on the base
with the mounting posts on the wall.
8
Push in and down until the phone is
firmly mounted.
On the base unit, slide the handset
retainer up out of the slot and rotate it
9
180 degrees.
Flip the retainer from front to back.
Slide it back into the slot so that the
10
lip of the retainer is up and the oval is
down. The retainer holds the handset
in place.
No dial tone is heard when calling out.
■ The battery pack may be weak. Does the
LOW BATT indicator blink? Charge the
handset in the cradle for 12-15 hours.
■ Check the telephone cord connection at
both ends.
■ Check the AC adapter connection at the
back of the unit and wall outlet.
■ Disconnect the AC adapter for a few
minutes, then reconnect it.
■ Check the connection of the battery pack.
■ Reset the digital security code (see
page 18).
No page tone or ring is heard at the
handset.
■ The battery pack may be weak. Does the
LOW BATT indicator blink? Charge the
handset in the cradle for 12-15 hours.
■ The handset may be too far away from the
base.
■ Move the base away from appliances or
metal objects.
■ Check the AC adapter and telephone cord
connection.
■ Reset the digital security code (see
page 18).
The audio sounds weak and/or
interference noise is heard.
CHAN
■ Press
noise.
■ The handset is too far from the base.
■ Move the handset and/or base away from
potential sources of interference: metal
objects, electrical appliances such as
radio, TV, fluorescent lights, etc.
■ Orient the base antenna to vertical
position.
■ Reset the digital security code (see
page 18).
■ The battery pack may be weak. Does the
LOW BATT indicator blink? Charge the
to help eliminate background
21
handset in the cradle for 12-15 hours.
■ Check the AC adapter and telephone cord
connection.
The STATUS INDICATOR won’t come on
when the handset is placed in the base
unit.
■ Check the AC adapter connection at both
ends.
■ Make sure the handset is properly placed
in the base unit (face up or face down).
■ Make sure the charging contacts on the
handset and base are clean.
■ Check the battery pack connection.
You hear continuous short beeps instead of
a dial tone when using the handset.
The beep tones are a warning alarm to let you
know:
■ The handset is out of communication
range with the base. Move the handset
closer to the base.
■ The base had some problem like a power
failure. Return the handset to the charging
cradle for 5 seconds and make sure all
cords are connected correctly.
The BATT LOW INDICATOR flashes after a
few telephone calls, even though the
battery has been fully charged for 12-15
hours.
■ Replace the battery pack with a new
battery.
You have more than one telephone
number and are experiencing difficulty.
■ See Multi-Line Installation (page 18).
Handset does not work after battery pack is
installed.
■ Reset the digital security code (see
page 18).
PAGE
PAGE
22
TROUBLESHOOTING
After several attempts, the CP-1260 will
not operate properly.
■ Disconnect the AC adapter for a few
minutes, then reconnect it. Remove the
battery pack from the handset. Plug the
AC ADAPTER back into the base and
reinsert the battery pack in the handset.
Return the handset to the charging cradle
for 20 seconds.
HERE’S HOW TO REACH US
By Phone:
HELPLINE:
(310) 320-9810, Monday - Friday,
8 a.m. to 4:45 p.m., PST
AUTHORIZED FACTORY SERVICE CENTER:
Phone Masters Repair Center
(714) 373-4233, Monday - Friday,
8 a.m. to 5 p.m., PST
PARTS ORDERS USING A CREDIT CARD:
Pacific Coast Parts Distributors, Inc.
(800) 421-5080 or (310) 515-0207,
Monday - Friday, 8 a.m. to 4:30 p.m., PST
On-line:
CUSTOMER RELATIONS:
WEBSITE: www.casiocomm.com
E-MAIL: cpmicust@casio.com
AUTHORIZED FACTORY SERVICE CENTER:
WEBSITE:
www.members.home.net/skelly1/
PM1.htm
E-MAIL: phonemasters@hotmail.com
PARTS AND ACCESSORIES:
WEBSITE: www.pacparts.com
E-MAIL: orders@pacparts.com
QUESTIONS?
AUTHORIZED FACTORY SERVICE CENTER
For repairs, please bring or send your unit to:
Phone Masters Repair Center
11899 Valley View Street
Garden Grove, CA 92845
1. Pack your product securely in a sturdy
shipping box.
2. Include a clear and specific explanation of
the problem.
3. Include your name, street address (sorry,
no P.O. box), and daytime phone number.
4. Provide a legible photocopy of the dated
store receipt for one-year warranty
purposes.
LIMITED WARRANTY
IMPORTANT!
SALES SLIP OR EVIDENCE OF PURCHASE DATE REQUIRED
This limited warranty gives you specific legal rights; you may also have other rights which vary from
state to state.
The limited warranty is extended only to the original consumer of a CASIO COMMUNICATIONS
product and is valid only with respect to consumers within the United States of America and Canada.
Subject to the following conditions, should this product prove defective by reason of improper
workmanship of material:
During the period of one (1) year from the date of original purchase, CASIO COMMUNICATIONS will
repair or, at its option, replace the product without charge for parts or labor. If CASIO
COMMUNICATIONS elects to replace the product, such replacement may be accomplished with a
factory-reconditioned unit.
This limited warranty does not apply: (a) to any product damaged by accident, misuse, improper line
voltage, lightning, fire, water, or other acts of nature, (b) if the product is altered or repaired by
anyone other than CASIO COMMUNICATIONS, INC. or one of its authorized warranty stations or if the
FCC-approved connector plugs are removed. This limited warranty does not cover tapes or broken or
marred cabinets.
Except to the extent prohibited by applicable law, all implied warranties made by CASIO
COMMUNICATIONS in connection with this product are limited in duration to a period of one (1) year
from the date of original purchase, and no warranties, whether expressed or implied, shall apply to
this product after said period.
Should this product prove defective in workmanship or material, the consumer’s sole remedies shall
be such repair or replacement as is hereinabove provided. Under no circumstances shall CASIO
COMMUNICATIONS be liable for any loss or damage, direct, consequential, or incidental arising out of
the use of or inability to use this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the above limitations or exclusion may not apply
to you.
In order to obtain warranty service, you must take or send the product, postage paid with a copy of
your sales receipt or other proof of purchase and date of purchase.
Before returning or exchanging your product,
call our Helpline at (310) 320-9810.
If you live in an area that is highly susceptible to electrical storms, you may want to purchase a
Lightning Arrestor/Surge Protector. The Lightning Arrestor/Surge Protector attaches to your telephone
device and if lightning causes a surge through your phone line, the arrestor will help suppress the
surge of electricity which may cause damage to your unit.
To purchase your Lightning Arrestor/Surge Protector with a credit card, call toll free:
(800) 421-5080 or (310) 515-0207.
23
PAGE
FCC REQUIREMENTS
PAGE
24
USER INSTRUCTIONS
1. This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that
contains, among other information, the FCC registration number and Ringer Equivalence Number (REN)
for this equipment. If requested, provide this information to your telephone company.
2. The REN is useful to determine the quantity of devices you may connect to your telephone line and still
have all of those devices ring when your number is called. In most, but not all areas, the sum of the
RENs of all devices should not exceed five (5.0). To be certain of the number of devices you may
connect to your line, as determined by the REN, you should call your local telephone company to
determine the maximum REN for your calling area.
3. If your telephone causes harm to the telephone network, the telephone company may discontinue your
service temporarily. If possible, they will notify you in advance. But if advance notice is not practical,
you will be notified as soon as possible. You will be advised of your right to file a complaint with the
FCC.
4. Your telephone company may make changes in its facilities, equipment, operations, or procedures that
could affect the proper operation of your equipment. If they do, you will be given advance notice so as
to give you an opportunity to maintain uninterrupted service.
5. If there is a problem with this unit, the telephone company may ask you to disconnect this equipment
from the network until the problem has been corrected or you are sure that the equipment is not
malfunctioning.
6. Repairs can only be made by the manufacturer or an authorized service agency. Unauthorized repairs
void registration and warranty. Contact seller or manufacturer for details of permissible user-performed
routine repairs, and where and how to have other than routine repairs made.
7. This equipment may not be used on coin service provided by the telephone company. Connection to
party lines is subject to state tariffs. (Contact your state public utility commission or corporation
commission for information.)
Jacks: RJ11 Ringer Equivalence: See bottom/underside of the CP-1260 unit.
CASIO COMMUNICATIONS, Inc. 20665 Manhattan Place, Torrance, CA 90501
ACCESSORIES
To order accessories for your CP-1260, to check on price or availability,
or to order parts using a credit card, call:
(800) 421-5080 or (310) 515-0207, Monday - Friday, 8 a.m. to 4:30 p.m., PST.
To order on-line: www.pacparts.com
E-MAIL: orders@pacparts.com
Description
Lightning Arrestor - Helps protect telephone answering machines from damage
caused by lightning-strikes to the telephone line.
electrical storms.
AC Adapter - For Model CP-1260
Replacement Battery Pack
Recommended for areas prone to
25
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
Any changes made by the user not approved by CASIO COMMUNICATIONS can void the user’s authority to
operate the equipment. This product is hearing aid compatible.
PAGE
26
Technical Specifications
FCC Registration No:See bottom/underside
of CP-1260 base
Frequency control: PLL
Operation Mode: Analog
Ringer Equivalence: See bottom/underside
of CP-1260 base
Jack: RJ11
40 channels
Power requirements:
Handset: Rechargeable NickelCadmium battery pack
Base: 9V 350mA (from AC
adapter)
PAGE
UCZZ01278BZ
27
EASY TO USE
OWNER'S GUIDE
CP-1260 900 MHz Dual Keypad
Cordless Phone with
Speakerphone
Base unit
RX frequency:
902.0525 MHz to 904.0025 MHz
TX frequency:
925.9975 MHz to 927.9475 MHz
Handset
RX frequency:
925.9975 MHz to 927.9475 MHz
TX frequency:
902.0525 MHz to 904.0025 MHz
Design and specifications are subject to change without notice.
Battery: Capacity 600 mAH, 3.6V
Battery Life:
Talk mode: 7 hours
Standby mode: 14 days
Recharging Time: 12-15 hours
CASIO COMMUNICATIONS, INC.
20665 Manhattan Place
Tor rance CA 90501
Internet web site address:
http://www.casiocomm.com
M1S1 4/00
Printed in China
PAGE
28
FEATURES
Loading...