For ClassPad 300/ClassPad 300 PLUS
OS Update
(ClassPad OS Version 2.20)
E
Application
User’s Guide
RJA510188-4
http://world.casio.com/edu/
http://classpad.net/
OS Update Application
OS Update Application performs a multi-step process that performs the following operations.
• Backup of data currently in the memory of your ClassPad
•Update of your ClassPad to Version 2.20
•Restoration of the backed up data
Important!
• The new ClassPad OS provides users with new solutions and superior display performance. However, once
ClassPad OS has been updated, it cannot be returned to a version of ClassPad OS earlier than version 2.20.
•Note that you must perform all of the steps in the procedure below, from preparing the ClassPad OS Update on your
computer to finalizing the operating installation procedure. If, for some reason, you cancel the procedure during any of
the following steps, the installation will not be performed correctly and you will have to restart the procedure from step
1.
•Never disconnect the USB cable unless specifically instructed to do so. Doing so can cause the calculator to
malfunction.
ClassPad OS Update Basic Steps
See the following pages of this manual for the details about each of these basic steps.
1. On your computer, prepare the ClassPad OS Update data for installation.
2. Install the ClassPad USB driver on your computer.
•This step is not necessary if the ClassPad USB driver (CESG502 USB) is already installed on your
computer.
3. Back up the data that is currently in the memory of your ClassPad.
4. Install the ClassPad OS Update on your ClassPad.
5. Re-configure ClassPad settings.
6. Restore the data that you backed up in step 3.
7. Finalize the installation update procedure.
Minimum System Requirements
Computer: IBM PC/AT or compatible with USB port
CPU: Intel
Operating System: Windows
Disk Space: 100 MB available for installation
Memory: 16 MB, 32 MB recommended
Video Display: 800 × 600 or higher video adaptor and monitor
®
Pentium® II 200 or AMD DuronTM, Intel® Pentium® II 300 recommended
®
98SE/Me or Windows® 2000/XP
Above values do not include memory required for the operating system.
Note
•Windows is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
• Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States
and other countries.
• AMD Duron is a registered trademark or trademark of Advanced Micro Devices, Inc. in the United States and/or other
countries.
•Company and product names used herein are trademarks of their respective owners.
20041001
20050601
E-1
Contents
1. Prepare the ClassPad OS Update data on your computer............................ E-3
2. Install the ClassPad USB driver on your computer. ...................................... E-6
3. Back up the data that is currently in the memory of your ClassPad. .......... E-7
4. Install the ClassPad OS Update on your ClassPad. ...................................... E-8
5. Re-configure ClassPad settings. ..................................................................... E-9
6. Restore the data that you backed up in section 3. ...................................... E-11
7. Finalize the installation update procedure. .................................................. E-12
E-2
20041001
20040201
1 Prepare the ClassPad OS Update data on your
computer.
1
. On your computer, double-click “ClassPad 300 OS
Ver.02.20.3000 Update” or “ClassPad 300 OS
Ver.02.20.3000 Update.exe”.
2
. Click [Yes].
3
.Click the [Next] button to advance to the next
screen.
4
. Carefully read the terms and conditions of the license agreement.
20041001
20050601
E-3
1Prepare the ClassPad OS Update data on your computer.
5
. If you agree to the terms and conditions of the
license agreement, click “I accept the terms...”, and
then click the [Next] button.
• If you do not agree to the terms and conditions of
the license agreement, click “I do not accept the
terms ...” and then click the [Cancel] button to exit
the install procedure.
Carefully read the terms and conditions of the important information.
6
. If you agree to the terms and conditions of the
important information, click “I accept the terms …”,
and then click the [Next] button.
• If you do not agree to the terms and conditions of
the important information, click “I do not accept the
terms …” and then click the [Cancel] button to exit
the install procedure.
7
. Click the [Install] button to advance to the
next screen.
•The dialog box guides you through the
operations you need to perform on your
ClassPad.
This area guides you through the operations you need
to perform on your ClassPad.
E-4
20031201
20050601
1Prepare the ClassPad OS Update data on your computer.
8
.Use the USB cable that comes with your ClassPad to connect to the computer.
Important!
•Never disconnect the USB cable unless specifically instructed to do so. Doing so can cause the calculator to
malfunction.
9
.What you should do next depends on what appears on your computer screen.
• If the Found New Hardware Wizard dialog box appears
This means your computer does not have the ClassPad USB driver installed. If this happens, perform
the procedure under “2. Install the ClassPad USB driver on your computer” on page E-6.
• If the ClassPad OS Update dialog box appears
Advance to the procedure under “3. Back up the data that is currently in the memory of your ClassPad”
on page E-7.
10
.Click [Next].
11
.Press the ClassPad o key to turn it on.
12
.Scroll down the application menu and
then tap B to start up the
Communication application.
13
.Tap E.
• If the Found New Hardware Wizard dialog box appears
This means your computer does not have the ClassPad USB driver installed. If this happens, perform
the procedure under “2. Install the ClassPad USB driver on your computer” on page E-6.
• If the ClassPad OS Update dialog box appears
Advance to the procedure under “3. Back up the data that is currently in the memory of your ClassPad”
on page E-7.
• If nothing happens, it means that the ClassPad’s “Cable Type” setting is something other than “USB
cable”. Use the procedure under “Configuring Communication Parameters” in the ClassPad 300 (page
15-3-1)/ClassPad 300 PLUS (page 16-3-1) User’s Guide to change the “Cable Type” setting to “USB
cable”. Next, tap the ClassPad
E icon.
20031201
2004020120050601
E-5
2 Install the ClassPad USB driver on your computer.
This step is necessary only if the Found New Hardware Wizard dialog box appears when you connected the
ClassPad to your computer.
Select “No, not this time”.
(Windows XP SP2 only)
1
.Select “Install the software automatically (Recommended)” and
then click [Next].
(Windows XP only)
2
.Though a message appears to let you know that the
software has not passed the “Windows Logo Test”,
there is no need for concern. Simply click [Continue
Anyway] and proceed with installation.
3
.After installation of the USB driver is complete, click [Finish].
4
.Perform the steps under “3. Back up the data that is currently in the memory of your ClassPad” on page
E-7.
E-6
20041001
20050601
3Back up the data that is currently in the memory
of your ClassPad.
Data backup starts automatically after you finish performing the
steps required up to this point.
•Never disconnect the USB cable unless specifically instructed to
do so. Doing so can cause the calculator to malfunction.
The screen shown below appears when data backup is complete.
1
. On your ClassPad, tap [OK].
2
. Next, perform the steps under “4. Install the ClassPad OS Update on your ClassPad” on page E-8.
20041001
E-7
4 Install the ClassPad OS Update on your ClassPad.
Perform the following steps on your ClassPad to update its operating system.
• The dialog box guides you through the operations you need to perform on
your ClassPad.
1
. On the [Link] menu, tap [Install] and then
[OS Update].
2
. Tap [OK] to start updating of the operating
system.
•Never disconnect the USB cable unless
specifically instructed to do so. Doing so
can cause the calculator to malfunction.
3
. Next, perform the steps under “5. Re-configure ClassPad settings” on page E-9.
E-8
20041001
5Re-configure ClassPad settings.
The screen shown below appears when operating system updating is complete.
This area guides you through the
operations you need to perform on
your ClassPad.
After its operating system is updated, your ClassPad should display the Touch Panel Alignment screen.
• The dialog box guides you through the operations you need to perform on your ClassPad.
1
. Tap the center of each of the four cross marks as they appear on the
display.
• If the Touch Panel Alignment screen does not appear, use the stylus to
press the P button on the back of the ClassPad.
2
. On the next screen that appears, tap the u button to make contrast darker,
or the t button to make it lighter.
After the contrast setting is the way you want, tap [Set].
•Tapping [Initial] on the Contrast dialog box returns contrast to its initial
factory default setting.
20041001
E-9
5 Re-configure ClassPad settings.
3
. On the next screen that appears, tap the language you want to use as the
system language, and then tap [Set].
•Tapping [Cancel] selects English and advances to the next screen.
4
. On the next screen that appears, tap the key arrangement you want to use,
and then tap [Set].
•Tapping [Cancel] selects QWERTY arrangement and advances to the next
screen.
5
. On the next screen that appears, tap the font set you want to use, and then
tap [Set].
•Tapping [Cancel] selects Bolder and finalizes the setup operation.
6
. Next, perform the steps under “6. Restore the data that you backed up in section 3” on page E-11.
E-10
20031101
2003120120050601
6Restore the data that you backed up in section 3.
Perform the following steps on your ClassPad to restore data.
• The dialog box guides you through the operations you need to perform on
your ClassPad.
1
. Scroll down the application menu and then tap B to start up the
Communication application.
2
. Tap .
3
. On your ClassPad, tap [OK].
4
. Next, perform the steps under “7. Finalize the installation update procedure” on page E-12.
20041001
20050601
E-11
7 Finalize the installation update procedure.
The screen shown below appears when OS update is complete.
1
. Click [Finish].
2
. Click [Finish].
3
. Disconnect the ClassPad from your computer.
E-12
20041001
CASIO COMPUTER CO., LTD.
6-2, Hon-machi 1-chome
Shibuya-ku, Tokyo 151-8543, Japan
SA0506-B
Loading...