Casio 5582 Instruction Manual

MA1902-EA
© 2019 CASIO COMPUTER CO., LTD.
Operation Guide 5582
Contents
Before Getting Started...
Watch Face and Display Indicators
Navigating Between Modes
Cycling Between Timekeeping Mode Digital
Display Contents
Shifting the Hands
Solar Charging
Using Mobile Link with a Mobile Phone
Getting Ready
A
Install the required app on your phone.
B
Configure Bluetooth settings.
C
Pair the watch with a phone.
Auto Time Adjustment
Viewing Stopwatch Data
Configuring Timer Settings
Setting the Alarm
Configuring World Time Settings
Adjusting Hand Alignment
Phone Finder
Configuring Watch Settings
Changing the Home City Summer Time Setting
Checking the Watch Charge Level
Connection
Connecting with a Phone
Disconnecting from a Phone
Using the Watch in a Medical Facility or Aircraft
Unpairing
If you purchase another phone
Stopwatch
Measuring Elapsed Time
Measuring Lap Times
Example: Recording a Race Lap Time
Viewing Measured Data Records
Lap Times
Timer
Setting the Countdown Start Time
Using the Timer
Alarms and Hourly Time Signal
Configuring Alarm Settings
Setting a Schedule Alarm
Enabling/Disabling an Alarm or the Hourly
Time Signal
Stopping an Alarm
Determining an Alarm’s On/Off Status
World Time
Checking World Time
World Time City Setting
Swapping Your Home Time and World Time
Adjusting Time Settings Manually
Setting a Home Time City
Setting the Time/Date
Switching between 12-hour and 24-hour
Timekeeping
Changing the Date Display Format
Specifying the Day of the Week Language
Light
Illuminating the Display Manually
Auto Light
Configuring the Auto Light Setting
Specifying the Illumination Duration
Hand Alignment Adjustment
Adjusting Hand Alignment
Other Settings
Enabling the Button Operation Tone
Configuring Power Saving Function Settings
Returning the Watch to Its Factory Default
Settings
Moving to Another Time Zone
Other Information
City Table
Summer Time Table
Supported Phones
Specifications
Mobile Link Precautions
Copyrights and Registered Copyrights
Troubleshooting
1
⑫ ⑬
⑤ ⑥ ⑦ ⑧ ⑨
DD
DD
D
D
Stopwatch Mode
Timer Mode
Alarm Mode
Timekeeping Mode
Recall Mode
World Time Mode
Mode hand
C
After connectionBefore connection
Any button
Hour, minute,
second
Month, day, day
of the week
Home City
Operation Guide 5582
Before Getting
Started...
This section provides an overview of the watch and introduces convenient ways it can be used.
Note
The illustrations included in this operation guide have been created to facilitate explanation. An illustration may differ somewhat from the item it represents.

Watch Face and Display Indicators

N
In the Alarm Mode, the mode hand points to [AL].
O
In the World Time Mode, the mode hand points to [WT].

Navigating Between Modes

Press (D) to cycle between modes.
In any mode, hold down (D) for at least two seconds to enter the Timekeeping Mode.
Connecting with a Phone
Hold down (C) for at least 1.5 seconds to establish a connection with a phone.
To disconnect, press any button.

Cycling Between Timekeeping Mode Digital Display Contents

Each press of (A) in the Timekeeping Mode toggles between the display information as shown below.
A
Displayed during p.m. times while 12-hour timekeeping is being used.
B
Displayed while the watch’s hands are shifted for easier reading.
C
Displayed while Auto Light is enabled.
D
Moves in sync with the seconds count in the Stopwatch Mode.
E
Displayed while the watch is indicating summer time.
F
When the watch is standing by for connection with a phone, the second hand points to [R].
G
When the watch is connected with a
phone, the second hand points to e.
H
Displayed while an alarm is turned on.
I
Battery level In the Timekeeping Mode, the current charge level is indicated by the mode hand.
Displaying the Current Home City
In the Timekeeping Mode, pressing (E) will display the name of the currently selected Home City for a short while.
To return manually to what was shown before the Home City, press (E).
J
Displayed while in the Recall Mode.
K
Displayed while the hourly time signal is enabled.
L
In the Stopwatch Mode, the mode hand indicates speed.
M
In the Timer Mode, the mode hand points to [TR].
2
NOYES
Second hand
Operation Guide 5582

Shifting the Hands

Hand shift moves the hands out of the way for easy viewing of display information.
While holding down (B), press (D).
1.
This will shift the analog hands to allow easy viewing of display information.
To return the hands to their normal
2.
timekeeping positions, hold down (B) as you press (D) again, or press (D) to change to another mode.
Note
If you leave the watch with its hands shifted and do not perform any operation for about one hour, the hands will resume normal timekeeping automatically.

Solar Charging

This watch runs on power supplied from a rechargeable (secondary) battery that is charged by a solar panel. The solar panel is integrated into the face of the watch, and power is generated whenever the face is exposed to light.
Charging the Watch
When you are not wearing the watch, put it in a location where it is exposed to bright light.
While you are wearing the watch, make sure that its face (solar panel) is not blocked from the light by the sleeve of your clothing. Power generation efficiency is reduced even when the face of the watch is blocked only partially.
Important!
Depending on light intensity and local conditions, the watch may become hot to the touch when exposed to light for charging. Take care to avoid burn injury after charging. Also, avoid charging the watch under high­temperature conditions like the ones described below.
On the dashboard of a vehicle
parked in the sun
Near an incandescent light bulb or
other source of heat
Under direct sunlight or in other hot
areas for long periods
Checking the Charge Level
In the Timekeeping Mode, the current charge level is indicated by the mode hand.
A
Good (high charge)
B
Good (medium charge)
C
Low Battery
Remaining Charge and Dead Battery
You can determine if the charge level is low by checking the hand movement. Functions become disabled as battery power goes low.
Important!
Should the battery go low or go dead, expose the face (solar panel) to light as soon as possible.
Note
Exposing the watch face to light after the battery goes dead will cause the [CHARGE] indicator to appear and the second hand to rotate counterclockwise until it stops at second 57. This indicates charging has started.
Low Battery Power
The second hand jumps at two-second intervals.
Dead Battery
All hands are stopped.
Charging Time Guidelines
The table below shows guidelines for approximate charging times.
Required Charging Time for 1-day Use
Light Level (Lux)
Approximate
Charging Time
50,000 8 minutes 10,000 30 minutes
5,000 48 minutes
500 8 hours
Time Required to Achieve Next Charge Level
Sunny day, outdoors (50,000 lux)
Dead battery charge
Medium charge n High charge
High charge n Full charge
Sunny day, near a window (10,000 lux)
Dead battery charge
Medium charge n High charge
High charge n Full charge
Overcast day, near a window (5,000 lux)
Dead battery charge
Medium charge n High charge
High charge n Full charge
Indoor fluorescent lighting (500 lux)
Dead battery charge
Medium charge n High charge
High charge n Full charge
Medium
n
Medium
n
Medium
n
Medium
n
2 hours
21 hours
6 hours
6 hours
77 hours
21 hours
10 hours
125 hours
34 hours
117 hours
-
-
3
12:30
Operation Guide 5582
Note
Actual charging time depends on the local charging environment.
Power Saving Function
Leaving the watch in a dark location for about one hour between the hours of 10 p.m. and 6 a.m. will cause the display to go blank, and the watch to enter Level 1 power saving. If the watch is left in this condition for six or seven days, the watch will enter Level 2 power saving.
Power Saving Level 1 : The second hand stops at 12 o’clock and the
digital display goes blank to save power. The watch can connect with a phone at this level.
Power Saving Level 2 : All hands stop and the digital display goes
blank to save power. All functions are disabled.
Recovering from Power Saving Operation
Use one of the operations below to exit power saving.
Press any button.
Move the watch to a bright location.
Trigger auto light by angling the watch towards your face.

Useful Features

Pairing the watch with your phone makes a number of the watch’s features easier to use.
Auto Time Adjustment
Auto Time Adjustment
l
Selection of More Than 300 World Time Cities
Configuring World Time Settings
l
Using Mobile Link with
a Mobile Phone
While there is a Bluetooth connection between the watch and phone, the watch time setting is adjusted automatically. You can also change the watch’s other settings.
Note
This function is available only while EDIFICE Connected is running on the phone.
This section describes watch and phone operations.
: Watch operation
X
: Phone operation
Y

Getting Ready

A
Install the required app on your
phone.
In Google Play or the App Store, search for the CASIO “EDIFICE Connected” app and install it on your phone.
Note
The watch will not enter power saving in the cases below.
Alarm Mode
While in the Stopwatch Mode
While in the Timer Mode
You can enable or disable Power Saving.
Configuring Power Saving Function
l
Settings
Note that the watch also may enter power saving if its face is blocked from light by your sleeve while you are wearing it.
Stopwatch Data Transfer to the Phone
Viewing Stopwatch Data
l
In addition, a number of other watch settings can be configured using your phone.
For transfer data to a watch and to configure settings, you first need to pair the watch with your phone.
Getting Ready
l
Your phone needs to have the CASIO “EDIFICE Connected” app installed to pair with the watch.
B

Configure Bluetooth settings.

Enable the phone’s Bluetooth.
Note
For details about setting procedures, see your phone documentation.
C

Pair the watch with a phone.

Before you can use the watch in combination with a phone, you first need to pair them.
Move the phone to be paired with close to
1.
(within one meter of) the watch.
2.
On the Home Screen, tap the “EDIFICE
Y
Connected” icon.
4
Pairing complete.Pairing started.
12:30
Trying to connect
Following time
adjustment
Trying to connect
Connected
Operation Guide 5582
3.
Perform the operation shown on the
Y
phone screen to be paired with.
If a pairing prompt message appears, perform the operation shown on the phone screen.
When pairing starts, the second hand will point to [R]. When pairing is complete, the second hand will move to
.
e

Auto Time Adjustment

Your watch will connect with a phone at preset times each day and adjust its time settings automatically.
Using Auto Adjust
Your watch adjusts its time setting four times a day according to a preset schedule. If you leave your watch in the Timekeeping Mode, it will perform the adjustment operation automatically as you go about your daily life, without any operation required by you.
Note
If the watch does not indicate the correct time even if is able to connect with a phone, correct the hand and date indicator positions.
Adjusting Hand Alignment
l
If there is a World Time City specified with EDIFICE Connected, its time will also be adjusted automatically.
The watch will connect with the phone and perform auto time adjustment at around 12:30 a.m., 6:30 a.m., 12:30 p.m. and 6:30 p.m. The connection is automatically terminated after auto time adjustment is complete.
The watch cannot connect with a phone for time adjustment while a stopwatch measurement or timer operation is in progress.
Triggering Immediate Time Adjustment
The watch’s time setting will be adjusted automatically whenever you establish a connection between the watch and a phone. Whenever you want to adjust the watch’s time setting based on your phone's time, perform the procedure below to connect with a phone.
Move the phone close to (within one meter
1.
of) the watch.
2.
Press (C).
X
[SET] flashes to indicate that the watch has started the connection operation. Once the watch and phone are connected, [OK] will appear, and then the watch will adjust its time setting based on information from the phone.

Viewing Stopwatch Data

This section explains how to send lap times (up to 200 records) that are stored in watch memory, as well as other data to your phone for viewing with EDIFICE Connected.
Sending Stopwatch Data to a Phone
Use the procedure below to send data from the watch to a phone.
1.
Tap the “EDIFICE Connected” icon.
Y
2.
Hold down (C) for at least 1.5 seconds
X
until [CNCT] starts to flash.
When a connection is established between the watch and phone, [CNCT] will stop flashing and the second hand will
move from [R] to e.
If connection fails for some reason, [ERR] will appear on the display momentarily and then the watch will return to the mode it was in before you started the connection procedure.
3.
Perform the operation shown on the
Y
phone screen to transfer data measured by the watch to the phone.
After data transfer is complete, a list of the measurement data will appear on the phone display.
Tapping a stopwatch data item displays its details.
Important!
The watch may not be able to perform auto time adjustment under the conditions described below.
While the watch is too far away from
its paired phone
While communication is not possible
due to radio interference, etc.
While the phone is updating its
system
Note
You can perform the above operation for time adjustment from any watch mode.
The connection is terminated automatically after time adjustment is complete.
If time adjustment fails for some reason, [ERR] will appear.
Checking a Lap Time
Use EDIFICE Connected to check the data you sent to the phone.
1.
Tap the “EDIFICE Connected” icon.
Y
2.
Perform the operation shown on the
Y
phone screen to view the measurement data you want.
Note
Tapping “Edit” displays a screen that you can use to change the data item title and to delete lap time data.
5

Configuring Timer Settings

Trying to connect
Connected
Trying to connect
Connected
Trying to connect
Connected
Trying to connect
Connected
1.
Tap the “EDIFICE Connected” icon.
Y
2.
Hold down (C) for at least 1.5 seconds
X
until [CNCT] starts to flash.
When a connection is established between the watch and phone, [CNCT] will stop flashing and the second hand will
move from [R] to e.
If connection fails for some reason, [ERR] will appear on the display momentarily and then the watch will return to the mode it was in before you started the connection procedure.
3.
Perform the operation shown on the
Y
phone screen to configure the timer time setting.

Setting the Alarm

1.
Tap the “EDIFICE Connected” icon.
Y
2.
Hold down (C) for at least 1.5 seconds
X
until [CNCT] starts to flash.
When a connection is established between the watch and phone, [CNCT] will stop flashing and the second hand will
move from [R] to e.
If connection fails for some reason, [ERR] will appear on the display momentarily and then the watch will return to the mode it was in before you started the connection procedure.
3.
Perform the operation shown on the
Y
phone screen to configure alarm time settings.
Operation Guide 5582

Configuring World Time Settings

Specifying a World Time City with EDIFICE Connected causes the watch’s World Time City to change accordingly. Watch settings can be configured to perform auto summer time switching for the World Time City.
Note
EDIFICE Connected World Time lets you select from among approximately 300 cities as the World Time City.
Selecting a World Time City
1.
Tap the “EDIFICE Connected” icon.
Y
2.
Hold down (C) for at least 1.5 seconds
X
until [CNCT] starts to flash.
When a connection is established between the watch and phone, [CNCT] will stop flashing and the second hand will
move from [R] to e.
If connection fails for some reason, [ERR] will appear on the display momentarily and then the watch will return to the mode it was in before you started the connection procedure.
3.
Perform the operation shown on the
Y
phone screen. The World Time setting will be reflected on the watch.
Note
You can use EDIFICE Connected to select from among World Time cities in addition to those built into the watch. The additional cities can be selected only by using EDIFICE Connected.
1.
2.
3.
Configuring the Summer Time Setting
Tap the “EDIFICE Connected” icon.
Y
Hold down (C) for at least 1.5 seconds
X
until [CNCT] starts to flash.
When a connection is established between the watch and phone, [CNCT] will stop flashing and the second hand will
move from [R] to e.
If connection fails for some reason, [ERR] will appear on the display momentarily and then the watch will return to the mode it was in before you started the connection procedure.
Perform the operation shown on the
Y
phone screen to select a summer time setting.
“Auto” The watch switches between standard time and summer time automatically.
“OFF” The watch always indicates standard time.
“ON” The watch always indicates summer time.
Note
While the summer time setting is “Auto”, the watch will switch between standard time and summer time automatically. You do not need to switch between standard time and summer time manually. Even if you are in an area that does not observe summer time, you can leave the watch’s summer time setting as “Auto”.
For information about summer time periods, refer the “Summer Time Table” or EDIFICE Connected.
6
Trying to connect
Connected
Trying to connect
Connected
Trying to connect
Disconnected
ConnectedSearching for phone
Trying to connect
Connected
Swapping Your World Time and Home Time
1.
Tap the “EDIFICE Connected” icon.
Y
2.
Hold down (C) for at least 1.5 seconds
X
until [CNCT] starts to flash.
When a connection is established between the watch and phone, [CNCT] will stop flashing and the second hand will
move from [R] to e.
If connection fails for some reason, [ERR] will appear on the display momentarily and then the watch will return to the mode it was in before you started the connection procedure.
3.
Perform the operation shown on the
Y
phone screen to swap your Home Time with your World Time.
Note
Auto time adjustment does not work for 24 hours after swapping of the Home Time and World Time.
Operation Guide 5582

Adjusting Hand Alignment

If the hands are out of alignment even though auto time adjustment is being performed, use EDIFICE Connected to adjust them.
1.
Tap the “EDIFICE Connected” icon.
Y
2.
Hold down (C) for at least 1.5 seconds
X
until [CNCT] starts to flash.
When a connection is established between the watch and phone, [CNCT] will stop flashing and the second hand will
move from [R] to e.
If connection fails for some reason, [ERR] will appear on the display momentarily and then the watch will return to the mode it was in before you started the connection procedure.
3.
Perform the operation shown on the
Y
phone screen to correct hand alignment.

Phone Finder

You can use phone finder to trigger a tone on the phone to make it easy to find. The tone is forced to sound even if the phone is in vibrate mode.
Important!
Do not use this function in areas where phone call tones are restricted.
The tone sounds at a high volume. Do not use this function when listening to phone output over earphones.
2.
3.
4.

Configuring Watch Settings

You can use EDIFICE Connected to specify the amount of time until a Bluetooth connection is automatically terminated, to enable or disable the watch operation tone, and to configure other settings.
1.
2.
If the watch is in any mode besides the
X
Timekeeping Mode, hold down (D) for at least two seconds to enter the Timekeeping Mode.
Hold down (E) for at least 1.5 seconds
X
until the second hand moves to [R].
The phone will sound a tone when it establishes a connection with the watch.
It will take a few seconds before the phone tone sounds.
Press any button to stop the tone.
X
You can press any watch button to stop the phone tone only during the first 30 seconds after it starts to sound.
Tap the “EDIFICE Connected” icon.
Y
Hold down (C) for at least 1.5 seconds
X
until [CNCT] starts to flash.
When a connection is established between the watch and phone, [CNCT] will stop flashing and the second hand will
move from [R] to e.
If connection fails for some reason, [ERR] will appear on the display momentarily and then the watch will return to the mode it was in before you started the connection procedure.
1.
If the watch is connected with a phone,
X
press any button to terminate the connection.
3.
Select the setting you want to change
Y
and then perform the operation shown on the phone screen.
7
Loading...
+ 15 hidden pages