MA1705-EA
© 2017 CASIO COMPUTER CO., LTD.
Operation Guide 5547/5563/5572
• Be sure to keep all user documentation handy for future reference.
• Your watch may differ somewhat from the one shown in the illustration.
Minute Hand
24 Hour Hand
Hour Hand
Stopwatch Minute Hand
Second Hand
Stopwatch functions
To adjust the time setting
When the second hand is at
12 o’clock, pull the
Click 2.
Rotate the Crown to change the
time setting.
Push the Crown back in on a time
signal to resume timekeeping.
Note
• Take care that you set the correct AM
or PM time.
• When changing the time, move the
minute hand four or five minutes past
your final setting, and then back it up
to the setting you want.
Crown Operations
Some water-resistant models (100 meters, 200 meters) have a
screw-in crown. When you need to perform a crown operation,
rotate it towards you to unscrew it. Then pull the crown out.
Avoid applying undue force when pulling. The watch loses
its water resistance while the crown is unscrewed. After
performing a crown operation, fully screw the crown back in.
If your watch has a rotary bezel...
You can rotate the bezel to align its ▼ mark with the
minute hand. Then you will be able to tell how much
time has elapsed since aligning the ▼ mark.
Low Battery Alert
The second hand will jump at two-second intervals to alert you when the charge is low.
•
Have the battery replaced as soon as possible after low battery alert is indicated.
•
Stopwatch operation is disabled during low battery alert.
•
• If low battery alert occurs during a stopwatch operation, the stopwatch will
automatically reset to all zeros and stop.
Crown out to
30
Day Indicator
Stopwatch Second Hand
To change the day indicator setting
Pull the Crown out to Click 1.
Rotate the Crown towards you to
set the day.
Push the Crown back in.
Note
• The day indicator setting uses a
31-day month. Make adjustments for
months of shorter lengths.
• Avoid changing the day indicator
setting between the hours of 9
p.m. and 1 a.m. Otherwise, the day
indicator may not change correctly
at midnight.
Current
Click 2
Click 1
Crown
Crown
Loosen
Start
Elapsed time
Using the Stopwatch
The stopwatch measures elapsed time in 1-second increments up to 9minutes,
59seconds.
Elapsed time
A A A A B
Start Stop Resume Stop Reset
Split time
A
Start Split Split release Stop Reset
Two finishes
A B A B B
Start Split
Important!
• Do not operate the stopwatch with the crown pulled out.
Note
• An elapsed time operation will stop automatically at the end of 10 minutes.
B B A B
First runner
finishes.
Display time of
first runner.
Stop
Second runner
finishes.
Split release
Display time of
second runner.
Reset
Correcting the 0 Positions of the Hands
Perform the following procedure if the stopwatch hands do not return to their 0 (zero)
positions when you reset the stopwatch.
Pull the Crown out to Click 2.
Use A (clockwise) and B (counterclockwise) to move the
Stopwatch Second Hand
• Holding down either button will move the second hand at high speed, until you
release the button.
• The
Stopwatch Minute Hand
After all of the hands are the way you want, push the Crown back in.
Important!
• Timekeeping stops while the crown is pulled out. Correct the current time setting
after performing the above operation.
to 12 o’clock and the
is syncronized with the
Stopwatch Minute Hand
Stopwatch Second Hand
to 0.
Specifications
Accuracy at normal temperature: ±20 seconds a month
Stopwatch: Measuring Capacity: 9'59" (10 minutes)
Other: Low battery alert
Battery: One silver oxide battery (Type: SR920SW)
Battery Life: Approximately 3 years
Specifications are subject to change without notice.
Measuring Unit: 1 second
Measurements: Elapsed time; split time; two finishes
.
1
Loading...