Casio 1382 Owner's Manual

Module No. 1382

GENERAL GUIDE

• Press C to change from mode to mode. After you perform an operation in any mode, pressing C returns to the Timekeeping Mode.

Timekeeping Mode

1382-1

• Press L in any mode to illuminate the display for about two seconds.

Telememo Mode World Time Mode

Press C

▲

Hand Setting Mode

▼

TIMEKEEPING MODE

In addition to time and date settings, the Timekeeping Mode also lets you adjust the contrast of the digital display.

• The Timekeeping Mode is actually made up to four sub-modes. Press D to switch between the sub-modes.

Time/Date

Day of week

PM indicator

• This watch displays text for the day of the week in any one of the five different languages (English, German, French, Italian, and Spanish).

• See the “Day of the Week List” at the back of this manual for information on abbreviations used.

About Manual Time Setting and Time Calibration Signal Reception

The current time for this watch can be set by inputting the time and date you want (manual setting) or by a time calibration signal. Note that the time calibration signal is available only in certain areas in Europe. For details on time calibration reception and the areas in which the time calibration signal is available, see the section of this manual titled: “TIME CALIBRATION SIGNAL RECEPTION.”

To set the current time manually

Receive indicator

Auto 

Receive

• The Auto Receive, DST, and GMT differential settings are used for time calibration signal reception only. For details on these settings, see the section of this manual titled: “TIME CALIBRATION SIGNAL RECEPTION.”

• See the section of this manual titled “To adjust the display contrast” for details on using the CNT (contrast) setting.

Month-Date

Seconds

Hour : Minutes

▼

▲

Date

Seconds

▼

1. Press B while in the Timekeeping Mode. The current Auto Receive on/off setting flashes on the display because it is

DST Seconds

• The receive indicator also flashes along with

the current on (

2. Press C to change the selection in the following sequence.

Language

ON) /off (OFF) setting.

GMT

differential

12/24-Hour

format

Analog

▲

selected

HourMinutesYearMonthDateCNT

▼

Stopwatch Mode Alarm Mode

▼

Language indicator

Press D

ENG

(English)

Press A

5. Press C until the 12/24-hour indicator is flashing on the display.

•

12H indicates 12-hour format, while 24H indicates 24-hour format.

6. Press D to toggle between the 12-hour (

• With the 12-hour format, the P (PM) indicator appears to the left of the digital time for times in the range of noon to 11:59 pm. Times from midnight to 11:59 am are shown without any indicator.

• With the 24-hour format, times are indicated in the range of 00:00 to 23:59, with a 24 indicator to the left of the digital time.

7. Press C until the seconds digits are flashing on the display.

8. Press D to reset the seconds to

• If you press D while the seconds count is in the range of 30 to 59, the seconds are reset to count is 00 to 29, the minutes count is unchanged.

9. Press C until the hour digits are flashing on the display.

10.Press D to increase the setting or A to decrease it. Holding down either

button changes the setting at high speed.

11.Repeat steps 9 and 10 to set the minutes, year, month, and date.

12.After you make the settings you want, press B to return to the

Timekeeping Mode.

• When you use the above procedure to set the digital display time, the hands of the analog timepiece normally adjust according to your setting. If, for any reason, the digital time does not match the analog time, use the procedure described under “HAND SETTING MODE” to match the analog setting with the digital display.

• The date can be set within the range of January 1, 1995 to December 31, 2039.

• If you do not operate any button for a few minutes while a selection is

flashing, the flashing stops and the watch goes back to the Timekeeping Mode automatically.

DEUT.

(German)

3. Press C until the language indicator is flashing on the display.

• The language indicator shows the language

currently set for the day of the week.

• The day of the week is set automatically in

accordance with the date.

4. Use A and D to change the language

setting in the following sequence.

FRA

(French)

00.

00 and 1 is added to the minutes. If the seconds

ITA

(Italian)

12H) and 24-hour (24H) formats.

ESP

(Spanish)

To adjust the display contrast

CNT indicator

3. Use D to increase the contrast value and A to decrease it.

4. After you make the setting you want, press B to return to the Timekeeping Mode.

1. Press B while in the Timekeeping Mode. The current Auto Receive on/off setting

flashes on the display because it is

2. Press C 11 times until the indicator is flashing on the display.

• The value to the right of the

shows the current contrast setting. You can set the contrast to a value from 1 (lightest) to 7 (darkest).

selected

CNT (contrast)

CNT indicator

1382-2

About the backlight

In any mode, press L to illuminate the display for about two seconds.

• The backlight of the watch employs an electro-luminescent (EL) panel, which loses illuminating power after very long use.

• The illumination provided by the backlight may be hard to see when viewed under direct sunlight.

• The watch will emit an audible sound whenever the display is illuminated. This is caused by a transistor that vibrates when the EL panel lights up. It does not indicate malfunction of the watch.

• The backlight automatically turns off whenever an alarm sounds.

• The backlight remains lit for about two seconds from the point you press

L, even if it is already lit when you press L. If you keep L depressed for about 15 seconds, the backlight will automatically turn off.

TIME CALIBRATION SIGNAL RECEPTION

This watch is designed to pick up a time calibration signal that is being transmitted from Mainflingen, Germany and update its time setting in accordance with the signal. There are two different methods you can use to receive the signal: auto receive and manual receive. With auto receive, the watch automatically receives the calibration signal twice each day and makes appropriate adjustments. With manual receive, you perform a specific button operation to receive the calibration signal.

Important!

• If you are using the time calibration signal to set the time for this watch, be sure to correctly set your home city. Otherwise, there is the chance that the watch will not set the correct time. See the “To set your home city data” for details.

• Time calibration reception is limited to specific geographic areas in Europe. See “Time calibration signal reception precautions” for details.

• The current time setting in accordance with the time calibration signal takes priority over any time settings you make.

• The watch is designed to automatically update the date and day of the week for the period January 1, 1995 to December 31, 2039. Setting of the date by the time calibration signal cannot be performed starting from January 1,

2040.

• This watch can receive signals that differentiate between leap years and non-leap years.

• After the watch successfully receives time calibration signal data, it first applies it to adjust the digital time setting and then adjusts the analog setting to match the digital time. If, for any reason, the digital time does not match the analog time, use the procedure described under “HAND SETTING MODE” to match the analog setting with the digital display.

• Auto receive is turned on when the watch is shipped from the factory.

To set your home city data

You can make Auto Receive on/off, DST (daylight saving time), and GMT differential settings for your home city (the city where you normally use the watch). This data can be changed any time you move to another geographic area.

Receive indicator

Auto 

Receive

4. Press C until the DST indicator is flashing on the display along with the

current auto receive setting (

•

AUTO Setting

Daylight saving time is activated and cancelled automatically in accordance with time calibration signal data. Use this setting if you plan to use the watch in an area where the daylight saving time period starts and ends on the dates used in Germany.

•

ON Setting

One hour is added to the current time indicated by the time calibration signal and adjusted in accordance with the GMT time differential setting you make.

•

OFF Setting

Daylight saving time is not applied.

5. Use the A and D buttons to change the DST setting in the sequence

shown below.

6. After making the setting you want, press C until the

appears on the display.

• The value to the right of the Greenwich Mean Time. This value is based on standard times only, and it does not allow for daylight saving time (summer time).

DST Seconds

Press D

Press A

1. Press B while in the Timekeeping Mode.

The current Auto Receive on/off setting flashes on the display because it is

selected

• The receive indicator flashes along with the

2. Press D to toggle Auto Receive on and off.

3. Pressing C to changes to another

Language

AUTO ON OFF

current on (

ON) /off (OFF) setting.

selection in the following sequence.

GMT

differential

AUTO, ON, or OFF).

GMT indicator is the time differential from

12/24-Hour

format

HourMinutesYearMonthDateCNT

GMT indicator

7. Use the A and D buttons to change the GMT differential setting in the sequence shown below.

Press D

Press A

8. After making all the home city settings you want, press B to return to the Timekeeping Mode.

GMT+1 GMT+2 GMT+0

Time calibration signal reception precautions

• This watch is able to receive the time calibration signal being transmitted from Mainflingen, Germany (located 25 kilometers southeast of Frankfurt). Signal reception is possible within the area represented by a circle with a radius of about 1200 kilometers.

• Even when the watch is within the reception range, signal reception is impossible if the signal is blocked by mountains or other

Frankfurt

• Signal reception is affected by weather, atmospheric conditions, and seasonal changes.

• At long distances that are out of the line of sight of the signal transmitter, the signal is bounced off of the ionosphere. Because of this, such factors as changes in the reflectivity of the ionosphere, as well as movement of the ionosphere to higher altitudes due to seasonal atmospheric changes or the time of day may change the reception range of the signal and make reception temporarily impossible.

• Proper signal reception can be difficult or even impossible under the conditions listed below. When receiving indoors, move to a location as near as possible to a window. Think of the watch as acting like a TV or radio when it is receiving the signal.

Nearby TVs, refrigerators, computers, or other household appliances Far away from broadcasting stations, among ferro-concrete structures or near mountains. Underground, in tunnels or in ferro-concrete buildings. Near high-tension wires, neon signs, or radio stations with interfering frequencies. Near railroads, highways or airports. In trains or cars.

• Radio interference can cause incorrect signal reception.

• Strong electrostatic charge can result in the wrong time being set.

• The analog hands do not move during signal reception. The analog hand

setting is changed based on the digital time setting after the time calibration signal is successfully received.

• The daily alarm and hourly time signal do not operate during signal reception.

• The receive indicator ( receive function is in progress.

• The watch initially changes the digital time setting to match the data (German time) received in the time calibration signal. Next, it adjusts the received time in accordance with the GMT differential setting. Finally, the analog hands are adjusted in accordance with the digital time setting.

geological formations between the watch and signal source.

• This watch is designed to receive the signal transmitted from Mainflingen. This means that reception is best when the antenna built into the 12 o’clock edge of the watch is facing towards Mainflingen. Note, however, that moving the watch while the time calibration signal receive operation is taking place will make stable reception impossible.

) flashes on the digital display while a signal

To perform manual time calibration signal reception

1. In the Timekeeping Mode, hold down A

Receive indicator

• Pressing A while the the display returns to the Timekeeping Mode.

• To interrupt a receive operation and return to the Timekeeping Mode, press A.

until the figures in the digital display are cleared (about three seconds).

2. Release A to start time calibration signal reception, which is indicated by the flashing receive indicator.

• Time calibration signal reception takes from

8 to 15 minutes.

• When the receive operation is successful, the

message

LAST RECEIPT appears on

the display together with the received time and date for about one or two minutes. Next, the watch returns to the Timekeeping Mode.

• When the receive operation is unsuccessful,

the message display together with the date and time of the last successful receipt for about one or two minutes. Next, the watch returns to the Timekeeping Mode.

LAST RECEIPT or ERROR message is on

ERROR appears on the

+ 3 hidden pages