pm700/pm950
Professional Stereo Power Amplifier
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Table Of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .1 Unpacking and Paperwork . . . . . . . . . . . . . . .1 Features and Specifications
pm700 . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 pm950 . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Controls and Functions . . . . . . . . . . . . . . . . . .6
Installation Location and
General Precautions . . . . . . . . . . . . . . . . . .8 Mechanical Considerations . . . . . . . . . . . . .8 Rear Support for
Road Applications . . . . . . . . . . . . . . . . . . .8 Thermal Considerations . . . . . . . . . . . . . . .8 AC Power Considerations . . . . . . . . . . . . . .9 Magnetic Leakage
Considerations . . . . . . . . . . . . . . . . . . . . . .9 Input Wiring . . . . . . . . . . . . . . . . . . . . . . . .9 Input Sensitivity . . . . . . . . . . . . . . . . . . . . .9 Output Wiring . . . . . . . . . . . . . . . . . . . . . .10
Installation (continued)
Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Dual Mono . . . . . . . . . . . . . . . . . . . . . . . .10
Bridged Mono . . . . . . . . . . . . . . . . . . . . .10
Parallel Mono . . . . . . . . . . . . . . . . . . . . . .10
70V Distribution Systems . . . . . . . . . . . . .11
Clipping Eliminator . . . . . . . . . . . . . . . . .11
Level Defeat . . . . . . . . . . . . . . . . . . . . . . .11
Power ON Sequencing . . . . . . . . . . . . . . .11
Remote Turn-On of
One or More Amplifiers . . . . . . . . . . . . . .12
Operating Tips
Using the pm700/pm950 . . . . . . . . . . . . . .13
Accessory Options . . . . . . . . . . . . . . . . . .13
Servicing Instructions . . . . . . . . . . . . . . . . . .14
In Case of Difficulty . . . . . . . . . . . . . . . . . . .15
Care and Service Assistance . . . . . . . . . . . . .16
Warranty Information . . . . . . . . . . . . . . . . . .17
Introduction
Congratulations on your purchase of a new Carver Professional Power Amplifier. It is backed by state-of-the-art engineering and manufacturing techniques to bring you the best in quality craftsmanship and reliable performance. The pm700 and pm950 are specially designed for pro sound applications. Their rugged construction and low profile make them ideal for sustaining the abuses of the road with reliability and space-saving economy. And their accurate sound and ample power make them ideal for critical studio applications as well. The pm700 is rated at 350 watts per
channel into 4 ohms and 225 watts per channel into 8 ohms. In bridged mono operation it is rated at 700 watts into 8 ohms. The pm950 is rated at 475 watts per channel into 4 ohms and 325 watts per channel into 8 ohms. In bridged mono operation it is rated at 950 watts into 8 ohms. The sophisticated protection circuits designed into these amplifiers will protect your system should an unexpected fault occur. They also protect the amplifiers from excessive temperature, continuous current limiting and shorted outputs. The balanced input uses a high quality, high common-mode rejection differential amplifier for exceptional hum and noise rejection. The sequencing feature allows a rack of amplifiers to be powered up from a remote location. The daisy-chain connection scheme causes each amplifier to turn on in sequence, preventing the large in-rush current that can occur when an entire rack of amplifiers is turned on simultaneously. These power amplifiers were designed and manufactured by people with a lifetime commitment to providing the world’s finest components for music and sound reproduction. Thanks for placing your confidence in Carver Professional. We know your amplifier will provide many years of dependable service and reliable sound reproduction.
Unpacking and Paperwork
Carefully unpack the amplifier and keep the original carton and packing materials for future moving, shipment or long-term storage. After opening the box, please check for any visible signs of damage that were
not apparent from the outside of the box. If you do encounter what appears to be concealed damage, please consult your Carver Professional Dealer before installing the unit.
Important Paperwork
Make sure to save your sales receipt. Your receipt is extremely important to establish the duration of your Limited Warranty, and for insurance purposes. Next, make a note of the serial number which is located on the back of the amplifier. Record it in the space provided below for convenient reference.
Model:pm700 pm950
Serial Number:
Purchased at:
Date:
Finally, take a moment to fill out and return the Warranty Registration Card packed with the amplifier and return it to Carver Professional. This will allow us to keep you informed about new products as they become available.
1
pm700
•225W per channel into 8 ohms
350W per channel into 4 ohms
700W mono into 8 ohms
•XLR and 1/4” TRS input connectors
•Accepts balanced or unbalanced lines
•Multi-way Binding Post output connectors
•Independent 11 detent level controls for CH1 and CH2
•External Level Control Defeat Switch
•Dual Mono mode for operating both channels with
a single mono input
•Bridged Mono mode for combining the power of both channels into a single higher powered chan-
nel
•Input sensitivity set at 1.5V RMS from factory. Internally configurable to 0.775V RMS
•Internally configurable input polarity
•Internal connection points for add-on accessories
•Power ON Sequencer
•Class H dual-rail power supply
•Independent CH1 / CH2 Speaker relays will instantaneously disconnect if one of the following
fault conditions is detected: D.C. Offset
Over Temperature Short Circuit
•Additional protection circuitry includes:
Clipping Eliminator
NEXT
AC Line Fuse
•Power Connected / Standby indicator
•7 LED display per channel, including Power
Ready |
and Clip / Protect indicators |
•2-speed Fan cooled
•70-volt / 100-volt transformer option
•CE 1997 approved
2
|
Power Output:: |
(20Hz to 20kHz, with no |
|
|
more than 0.1% THD) |
|
|
225 watts per channel |
|
|
into 8 ohms |
|
|
350 watts per channel |
|
|
into 4 ohms |
|
|
Bridged-mono: |
|
|
700 watts into 8 ohms |
|
|
at 1kHz, with no more |
|
|
than 0.1% THD |
|
Dynamic Headroom: >2.0dB |
|
|
Frequency Response: |
|
|
|
20Hz to 20kHz (±0.75 |
BACK |
|
|
|
dB) |
|
|
Channel Separation: |
|
|
||
|
|
>65dB @ 1kHz |
|
Damping Factor: |
<400 |
|
Input Impedance: 25 Kohms unbalanced |
|
|
|
50 Kohms balanced |
|
Sensitivity: |
Low: 1.5 VRMS for |
|
|
rated power into 4 |
|
|
ohms 160mVRMS for |
|
|
1W into |
|
|
4 ohms |
|
|
High: 0.775VRMS for- |
|
|
rated power into 4 |
|
|
ohms 83mVRMS for 1W |
|
|
into 4 ohms; |
|
Gain: |
High: 33.8dB (±0.5dB) |
|
|
Low: 27.8dB (±0.5dB) |
|
Input Overload: |
+18dB |
|
THD: |
<0.1% |
|
IM Distortion: |
<0.1% |
Signal-to-Noise Ratio:
>100 dB, A-weighted, ref. to rated power into 4 ohms
Slew Rate: |
40V / µS |
|
|
||
|
(Bandwidth limited) |
|
CMRR: |
>80dB @ 1kHz |
|
Power Consumption:
55W at idle; 500W with musical program; 1000W at full power into 8 ohms (continuous); 1550W at full power into 4 ohms (continuous)
Power Requirements:
120VAC/ 60Hz (USA and Canada) Other voltages as required for export
Fusing: 10 amp slo-blo (120V / 60Hz) 7 amp slo-blo (230V / 50Hz)
Sequence Receive Terminal:
|
+7V to +15V DC |
|
50mA min. current |
|
requirement |
Display: |
7 LED indicators per |
|
channel 1 green |
|
READY, 5 yellow SIG- |
|
NAL, 1 red CLIP / |
|
PROTECT |
Size (H x W x D): |
3.50” (2U) x 19” x |
|
13.25” 89mm x 483mm |
|
x 337mm |
Net Weight: |
30 lbs. (13.6 kgs) |
Shipping Weight: |
36 lbs. (16.3 kgs) |
Due to on-going product development, features, specifications, and availability are subject to change without notice.
3
pm950
•325W per channel into 8 ohms
475W per channel into 4 ohms
950W mono into 8 ohms
•XLR and 1/4” TRS input connectors
•Accepts balanced or unbalanced lines
•Multi-way Binding Post output connectors
•Independent 11 detent Level Controls for CH1 and CH2
•External Level Control Defeat Switch
•Dual Mono mode for operating both channels with
a single mono input
•Bridged Mono mode for combining the power of both channels into a single higher powered chan-
nel
•Input sensitivity set at 1.5V RMS from factory. Internally reconfigurable to 0.7775V RMS.
•Internally configurable input polarity
•Internal connection points for add-on accessories
•Power ON Sequencer
•Class H dual-rail power supply
•Independent CH1 / CH2 Speaker relays will instantaneously disconnect if one of the following
fault conditions is detected: D.C. Offset
Over Temperature Short Circuit
•Additional protection circuitry includes:
Clipping Eliminator
AC Line Fuse
•Power Connected / Standby indicator
•7 LED display per channel, including Power Ready and Clip / Protect indicators
•2-speed Fan cooled
•70 volt / 100 volt transformer option
• CE 1997 approved |
NEXT |
4