Canon mf6600 Series, D1100 Series Service Manual

87654321

MF6600/D1100 Series

F-0-1F-0-1

Service Manual

Product Overview

Technical Overview

Periodical Services

Disassembly/Assembly

Adjustment

Trouble Shooting

Error Codes

Service Mode

Appendex

0-2

Application

This manual has been issued by Canon Inc. for qualied persons to learn technical theory, installation, maintenance, and repair of products. This manual covers all localities where the products are sold. For this reason, there may be information in this manual that does not

apply to your locality.

Corrections

This manual may contain technical inaccuracies or typographical errors due to improvements or changes in products. When changes occur in applicable products or in the contents of this

manual, Canon will release technical information as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new

edition of this manual.

The following paragraph does not apply to any countries where such provisions are inconsistent with local law.

of this manual.

The following paragraph does not apply to any countries where such provisions are inconsistent with local law.

Trademarks

The product names and company names used in this manual are the registered trademarks of the individual companies.

This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may not be copied, reproduced or translated into another language, in whole or in part, without the written consent of Canon Inc.

Caution

Use of this manual should be strictly supervised to avoid disclosure of condential

information.

0-3

Explanation of Symbols

The following symbols are used throughout this Service Manual.

Symbols Explanation Symbols Explanation

Used to show permission. Remove the screw.

Used to show prohibition. Tighten the screw.

Check. Remove the claw.

Check visually. Insert the claw.

Check the noise. Use the bundled part.

Disconnect the connector. Push the part.

Connect the connector. Plug the power cable.

Remove the cable/wire from the cable guide or wire

saddle.

Turn on the power.

Set the cable/wire to the cable guide or wire saddle.

T-0-1T-0-1

The following rules apply throughout this Service Manual:

1. Each chapter contains sections explaining the purpose of specic functions and the relationship between electrical and mechanical systems with reference to the timing of

operation.

In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol, the arrow indicates the direction of the electric signal. The expression "turn on the power" means ipping on the power switch, closing the front door, and closing the delivery unit door, which results in supplying the machine with power.

2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is "High", while '0' is used to indicate "Low". (The voltage value, however, differs from circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD signal goes on when '0'. In practically all cases, the internal mechanisms of a microprocessor cannot be checked in the eld. Therefore, the operations of the microprocessors used in the machines are not discussed: they are explained in terms of from sensors to the input of the DC controller

PCB and from the output of the DC controller PCB to the loads.

The descriptions in this Service Manual are subject to change without notice for product improvement or other purposes, and major changes will be communicated in the form of

Service Information bulletins. All service persons are expected to have a good understanding of the contents of this Service Manual and all relevant Service Information bulletins and be able to identify and isolate faults in the machine.

0-1

Contents

Safety Precautions

CDRH Provisions -------------------------------------------------------------0-2 Laser Safety --------------------------------------------------------------------0-2

About Laser Beams --------------------------------------------------------------- 0-2 Handling Laser Scanner Unit --------------------------------------------------- 0-2

Toner Safety --------------------------------------------------------------------0-3

About Toner ------------------------------------------------------------------------- 0-3

Handling Adhered Toner --------------------------------------------------------- 0-3

Notes When Handling A Battery -------------------------------------------0-3

Notes On Assembly/Disassembly -----------------------------------------0-3

Product Overview

Product Lineups ---------------------------------------------------------------1-2

Main Unit ----------------------------------------------------------------------------- 1-2

Options ------------------------------------------------------------------------------- 1-3

Product Features --------------------------------------------------------------1-3

Features ------------------------------------------------------------------------------ 1-3

Compact MFP ------------------------------------------------------------------------------- 1-3

High-speed MFP ---------------------------------------------------------------------------- 1-3 Power-saving MFP ------------------------------------------------------------------------- 1-3

Specications ------------------------------------------------------------------1-4

Main Unit Specications ---------------------------------------------------------- 1-4 ADF Specications ---------------------------------------------------------------- 1-5 FAX Specications ----------------------------------------------------------------- 1-5

Print Speed. ------------------------------------------------------------------------- 1-6 Paper types -------------------------------------------------------------------------- 1-6 Paper size --------------------------------------------------------------------------- 1-7

Name of Parts ------------------------------------------------------------------1-7

External View ----------------------------------------------------------------------- 1-7

Front Side ------------------------------------------------------------------------------------- 1-7 Rear Side ------------------------------------------------------------------------------------- 1-8

Cross Sectional View ------------------------------------------------------------- 1-9

ADF/Reader Unit ---------------------------------------------------------------------------- 1-9

Printer ------------------------------------------------------------------------------------------ 1-9

Operation Panel -------------------------------------------------------------------1-10

Main Operation Panel --------------------------------------------------------------------1-10 Send Operation Panel --------------------------------------------------------------------1-10

Function List ------------------------------------------------------------------------1-11

Copy Area -----------------------------------------------------------------------------------1-11 Reception Print Area ----------------------------------------------------------------------1-11

BDL Print Area ------------------------------------------------------------------------------1-11 PCL Print Area ------------------------------------------------------------------------------1-11

Operation Environment of the Printer Driver -------------------------------1-11

Operation environment -------------------------------------------------------------------1-11

Hardware environment -------------------------------------------------------------------1-11 Network Specications -------------------------------------------------------------------1-11 SEND Specications ----------------------------------------------------------------------1-12

Technical Overview

Basic Conguration -----------------------------------------------------------2-2

Conguration Function ----------------------------------------------------------- 2-2

Basic Sequence -------------------------------------------------------------------- 2-2

Basic Operational Sequence ------------------------------------------------------------ 2-2 Print Sequence ------------------------------------------------------------------------------ 2-3

Print Mode --------------------------------------------------------------------------- 2-4

Document Exposure/feeder System -------------------------------------2-5

Document Exposure System ---------------------------------------------------- 2-5

Specications / Control / Function List

i -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------2-5

Major Components ------------------------------------------------------------------------- 2-5

Document Feeder System ------------------------------------------------------- 2-6

Pickup/Feed/Delivery Operation -------------------------------------------------------- 2-6 Original Detection--------------------------------------------------------------------------- 2-7 Jam Detection ------------------------------------------------------------------------------- 2-8

Service Tasks ----------------------------------------------------------------------- 2-8

Action for Parts Replacement ----------------------------------------------------------- 2-8 Maintenance --------------------------------------------------------------------------------- 2-8 Service Notes -------------------------------------------------------------------------------- 2-8

Engine Control System ------------------------------------------------------2-9

0-2

Outline -------------------------------------------------------------------------------- 2-9 Controls ------------------------------------------------------------------------------ 2-9

Outline ----------------------------------------------------------------------------------------- 2-9 Motor Control -------------------------------------------------------------------------------2-10 Fan Control ----------------------------------------------------------------------------------2-11 Failure Detection ---------------------------------------------------------------------------2-11

Low-voltage Power Supply -----------------------------------------------------2-12

Outline ----------------------------------------------------------------------------------------2-12 Protective Function ------------------------------------------------------------------------2-13 Safety -----------------------------------------------------------------------------------------2-13

Low-voltage Power Supply Unit Failure Detection --------------------------------2-13 Power-Saving Mode ----------------------------------------------------------------------2-13

Service Tasks ----------------------------------------------------------------------2-14

Action for Parts Replacement ----------------------------------------------------------2-14 Maintenance --------------------------------------------------------------------------------2-14 Service Notes -------------------------------------------------------------------------------2-14

Laser Scanner System ----------------------------------------------------2-15

Outline -------------------------------------------------------------------------------2-15 Optical Unit Failure Detection --------------------------------------------------2-15 Service Tasks ----------------------------------------------------------------------2-15

Action for Parts Replacement ----------------------------------------------------------2-15 Maintenance --------------------------------------------------------------------------------2-15 Service Notes -------------------------------------------------------------------------------2-15

Image-formation System -------------------------------------------------- 2-16

Outline -------------------------------------------------------------------------------2-16 Image-formation Process -------------------------------------------------------2-16

Outline ----------------------------------------------------------------------------------------2-16 Latent Image Formation Block ---------------------------------------------------------2-17 Developing Block --------------------------------------------------------------------------2-17 Transfer Block ------------------------------------------------------------------------------2-18 Fixing Block ---------------------------------------------------------------------------------2-18 Drum Cleaning Block ---------------------------------------------------------------------2-18

High-voltage Power Supply ----------------------------------------------------2-19

Outline ----------------------------------------------------------------------------------------2-19

Service Tasks ----------------------------------------------------------------------2-19

Action for Parts Replacement ----------------------------------------------------------2-19 Maintenance --------------------------------------------------------------------------------2-19 Notes on Field Service -------------------------------------------------------------------2-19

Fixing Unit System ----------------------------------------------------------2-20

Outline -------------------------------------------------------------------------------2-20 Fixing Control Circuit -------------------------------------------------------------2-21

Throughput Reduction Control ---------------------------------------------------------2-21 Fixing Temperature Control -------------------------------------------------------------2-22 Protective Function ------------------------------------------------------------------------2-23 Failure Detection ---------------------------------------------------------------------------2-23

Service Tasks ----------------------------------------------------------------------2-24

At Parts Replacement --------------------------------------------------------------------2-24 Maintenance --------------------------------------------------------------------------------2-24 Notes On Service Works -----------------------------------------------------------------2-24

Media Feed System -------------------------------------------------------- 2-25

Outline -------------------------------------------------------------------------------2-25 Drive Conguration ---------------------------------------------------------------2-25 Jam Detection ---------------------------------------------------------------------2-26

Outline ----------------------------------------------------------------------------------------2-26 Pickup Delay Jam -------------------------------------------------------------------------2-27 Pickup Stationary Jam--------------------------------------------------------------------2-27 Delivery Delay Jam ------------------------------------------------------------------------2-27 Delivery Stationary Jam ------------------------------------------------------------------2-27 Fixing Paper Wrap Jam -----------------------------------------------------------------2-27 Reverse Delay Jam -----------------------------------------------------------------------2-27 Reverse Stationary Jam -----------------------------------------------------------------2-27 Internal Residual Jam --------------------------------------------------------------------2-27 Door Open Jam ----------------------------------------------------------------------------2-27

Service Tasks ----------------------------------------------------------------------2-27

At Parts Replacement --------------------------------------------------------------------2-27 Maintenance --------------------------------------------------------------------------------2-27 Notes On Service Works -----------------------------------------------------------------2-27

Periodical Services

Periodically Replaced Parts ------------------------------------------------3-2

Periodically Replaced Parts ----------------------------------------------------- 3-2 Consumables Expected Replacement Timing ------------------------------ 3-2

Consumable Parts ------------------------------------------------------------3-2

Durables Replaced by the User ------------------------------------------------ 3-2 Durables Replaced by the Service Person ---------------------------------- 3-2

0-3

Periodical Service -------------------------------------------------------------3-2

Periodical Service ------------------------------------------------------------------ 3-2

Cleaning -------------------------------------------------------------------------3-2

Cleaning at Service Visit --------------------------------------------------------- 3-2

Cleaning Method (External Covers)---------------------------------------------------- 3-3 Cleaning Method (Scanning Area) -----------------------------------------------------3-3 Cleaning Method (ADF) ------------------------------------------------------------------- 3-3 Fixing unit ------------------------------------------------------------------------------------- 3-4

Disassembly/Assembly

PREFACE -----------------------------------------------------------------------4-2

Outline -------------------------------------------------------------------------------- 4-2

List of Parts ---------------------------------------------------------------------4-3

External View ----------------------------------------------------------------------- 4-3

Front Side ------------------------------------------------------------------------------------- 4-3 Rear Side ------------------------------------------------------------------------------------- 4-4

Main Unit ----------------------------------------------------------------------------- 4-5 Main Parts --------------------------------------------------------------------------- 4-6

Sensor / Switc ------------------------------------------------------------------------------- 4-6 Motor / Fan ----------------------------------------------------------------------------------- 4-7 Other ------------------------------------------------------------------------------------------- 4-8 PCB -------------------------------------------------------------------------------------------- 4-9

Connector Layout Drawing (TAYPE I) ---------------------------------------4-10

Internal 1 -------------------------------------------------------------------------------------4-10 Internal 2 -------------------------------------------------------------------------------------4-12

Connector Layout Drawing (TAYPE II) --------------------------------------4-14

Internal 1 -------------------------------------------------------------------------------------4-14 Internal 2 -------------------------------------------------------------------------------------4-16

External Cover, Internal Cover -------------------------------------------4-18

External View ----------------------------------------------------------------------4-18

Front Side ------------------------------------------------------------------------------------4-18 Rear Side ------------------------------------------------------------------------------------4-19

Removing the Left Cover -------------------------------------------------------4-19

Procedure ------------------------------------------------------------------------------------4-19

Removing the Left Rear Cover ------------------------------------------------4-22

Preparations --------------------------------------------------------------------------------4-22 Procedure ------------------------------------------------------------------------------------4-22

Removing the Right Cover -----------------------------------------------------4-23

Procedure ------------------------------------------------------------------------------------4-23

Removing the Right Rear Cover ----------------------------------------------4-26

Preparations --------------------------------------------------------------------------------4-26 Procedure ------------------------------------------------------------------------------------4-26

Removing the Front Cover -----------------------------------------------------4-26

Preparations --------------------------------------------------------------------------------4-26 Procedure ------------------------------------------------------------------------------------4-26

Removing the Rear Cover Unit ------------------------------------------------4-27

Preparations --------------------------------------------------------------------------------4-27 Procedure ------------------------------------------------------------------------------------4-27

Removing the Upper Cover Unit ----------------------------------------------4-28

Preparations --------------------------------------------------------------------------------4-28 Procedure ------------------------------------------------------------------------------------4-28

Document Exposure, Feed System ------------------------------------4-30

Location -----------------------------------------------------------------------------4-30 Removing the ADF Unit ---------------------------------------------------------4-30

Procedure ------------------------------------------------------------------------------------4-30

Removing the ADF Unit + Reader Unit --------------------------------------4-33

Preparations --------------------------------------------------------------------------------4-33 Procedure ------------------------------------------------------------------------------------4-33

Separating the ADF Unit + Reader Unit -------------------------------------4-35

Preparations --------------------------------------------------------------------------------4-35 Procedure ------------------------------------------------------------------------------------4-35

Removing the ADF Roller Unit -------------------------------------------------4-37

Procedure ------------------------------------------------------------------------------------4-37

Removing the ADF Pickup Roller ---------------------------------------------4-38

Preparations --------------------------------------------------------------------------------4-38 Procedure ------------------------------------------------------------------------------------4-38

Removing the ADF Separation Roller ---------------------------------------4-39

Preparations --------------------------------------------------------------------------------4-39 Procedure ------------------------------------------------------------------------------------4-39

Removing the ADF Separation Pad ------------------------------------------4-41

Procedure ------------------------------------------------------------------------------------4-41

Removing the ADF Pickup Feed Unit ----------------------------------------4-42

Procedure ------------------------------------------------------------------------------------4-42

Removing the ADF Pickup Motor Unit ---------------------------------------4-45

0-4

Preparations --------------------------------------------------------------------------------4-45 Procedure ------------------------------------------------------------------------------------4-45

Removing the ADF Delivery Solenoid Unit ---------------------------------4-46

Preparations --------------------------------------------------------------------------------4-46 Procedure ------------------------------------------------------------------------------------4-46

Removing the Reader Unit Upper Cover -----------------------------------4-46

Preparations --------------------------------------------------------------------------------4-46 Procedure ------------------------------------------------------------------------------------4-46

Removing the CIS Unit ----------------------------------------------------------4-48

Preparations --------------------------------------------------------------------------------4-48 Procedure ------------------------------------------------------------------------------------4-48

Removing the Reader Motor Unit ---------------------------------------------4-51

Preparations --------------------------------------------------------------------------------4-51 Procedure ------------------------------------------------------------------------------------4-51

Controller System -----------------------------------------------------------4-53

Location1 ----------------------------------------------------------------------------4-53 Location2 ----------------------------------------------------------------------------4-54

Removing the Controller Cover -----------------------------------------------4-55

Preparations --------------------------------------------------------------------------------4-55 Procedure ------------------------------------------------------------------------------------4-55

Removing the ADF/Reader Driver PCB -------------------------------------4-55

Preparations --------------------------------------------------------------------------------4-55 Procedure ------------------------------------------------------------------------------------4-55

Removing the Main Controller Board ----------------------------------------4-56

Preparations --------------------------------------------------------------------------------4-56

Procedure (TYPE I) -----------------------------------------------------------------------4-56 Procedure (TYPE II) ----------------------------------------------------------------------4-57

Removing the NCU PCB --------------------------------------------------------4-58

Preparations --------------------------------------------------------------------------------4-58 Procedure ------------------------------------------------------------------------------------4-58

Removing the Capacitor PCB -------------------------------------------------4-59

Preparations --------------------------------------------------------------------------------4-59 Procedure ------------------------------------------------------------------------------------4-59

Removing the All-night Power PCB Mount (TYPE I) ---------------------4-59

Preparations --------------------------------------------------------------------------------4-59 Procedure ------------------------------------------------------------------------------------4-59

Removing the All-night Power PCB (TYPE I) ------------------------------4-60

Preparations --------------------------------------------------------------------------------4-60

Procedure ------------------------------------------------------------------------------------4-60

Removing the Power PCB (TYPE I) -----------------------------------------4-60

Preparations --------------------------------------------------------------------------------4-60 Procedure ------------------------------------------------------------------------------------4-60

Removing the Controller Box (TYPE I) --------------------------------------4-61

Preparations --------------------------------------------------------------------------------4-61 Procedure ------------------------------------------------------------------------------------4-61

Removing the Controller Box (TYPE II) -------------------------------------4-62

Preparations --------------------------------------------------------------------------------4-62 Procedure ------------------------------------------------------------------------------------4-62

Removing the Engine Controller Unit (TYPE I)----------------------------4-64

Preparations --------------------------------------------------------------------------------4-64 Procedure ------------------------------------------------------------------------------------4-64

Removing the Engine Controller Unit (TYPE II) ---------------------------4-67

Preparations --------------------------------------------------------------------------------4-67 Procedure ------------------------------------------------------------------------------------4-67

Removing the Control Panel ---------------------------------------------------4-70 Removing the Main Motor (TYPE I) ------------------------------------------4-71

Preparations --------------------------------------------------------------------------------4-71 Procedure ------------------------------------------------------------------------------------4-71

Removing the Main Motor (TYPE II) -----------------------------------------4-73

Preparations --------------------------------------------------------------------------------4-73 Procedure ------------------------------------------------------------------------------------4-73

Removing the Main Fan ---------------------------------------------------------4-75

Preparations --------------------------------------------------------------------------------4-75 Procedure ------------------------------------------------------------------------------------4-75

Removing the Power Cooling Fan --------------------------------------------4-75

Preparations --------------------------------------------------------------------------------4-75 Procedure ------------------------------------------------------------------------------------4-76

Removing the Controller Fan (TYPE I) --------------------------------------4-77

Preparations --------------------------------------------------------------------------------4-77 Procedure ------------------------------------------------------------------------------------4-77

Removing the Main Drive Unit (TYPE I) ------------------------------------4-77

Preparations --------------------------------------------------------------------------------4-77 Procedure ------------------------------------------------------------------------------------4-77

Removing the Main Drive Unit (TYPE II) ------------------------------------4-81

Preparations --------------------------------------------------------------------------------4-81 Procedure ------------------------------------------------------------------------------------4-81

0-5

Removing the Duplex Drive Unit (TYPE I) ----------------------------------4-84

Preparations --------------------------------------------------------------------------------4-84 Procedure ------------------------------------------------------------------------------------4-84

Removing the Duplex Drive Unit (TYPE II) ---------------------------------4-86

Preparations --------------------------------------------------------------------------------4-86 Procedure ------------------------------------------------------------------------------------4-86

Removing the Manual Tray Pickup Solenoid (TYPE I) ------------------4-88

Preparations --------------------------------------------------------------------------------4-88 Procedure ------------------------------------------------------------------------------------4-88

Removing the Manual Tray Pickup Solenoid (TYPE II) -----------------4-89

Preparations --------------------------------------------------------------------------------4-89 Procedure ------------------------------------------------------------------------------------4-89

Removing the Duplex Reverse Solenoid -----------------------------------4-90

Preparations --------------------------------------------------------------------------------4-90 Procedure ------------------------------------------------------------------------------------4-90

Removing the Cassette Pickup Solenoid -----------------------------------4-90

Preparations --------------------------------------------------------------------------------4-90 Procedure ------------------------------------------------------------------------------------4-90

Removing the Speaker (TYPE I) ----------------------------------------------4-91

Preparations --------------------------------------------------------------------------------4-91 Procedure ------------------------------------------------------------------------------------4-91

Removing the Speaker (TYPE II) ---------------------------------------------4-92

Preparations --------------------------------------------------------------------------------4-92 Procedure ------------------------------------------------------------------------------------4-92

Laser Exposure System ---------------------------------------------------4-93

Location -----------------------------------------------------------------------------4-93 Removing the Laser Scanner Unit --------------------------------------------4-93

Preparations --------------------------------------------------------------------------------4-93 Procedure ------------------------------------------------------------------------------------4-93

Image Forming System ----------------------------------------------------4-95

Location -----------------------------------------------------------------------------4-95 Removing the Transfer Roller --------------------------------------------------4-95

Removing the Registration Unit -----------------------------------------------4-96

Preparations (TYPE I) --------------------------------------------------------------------4-96 Preparations (TYPE II) -------------------------------------------------------------------4-96

Procedure ------------------------------------------------------------------------------------4-96

Fixing System ----------------------------------------------------------------4-98

Location -----------------------------------------------------------------------------4-98 Removing the Fixing Unit -------------------------------------------------------4-98

Preparations --------------------------------------------------------------------------------4-98

Procedure (TYPE I) -----------------------------------------------------------------------4-98 Procedure (TYPE II) --------------------------------------------------------------------4-101

Paper Feed/Transport/Output System ------------------------------- 4-104

Location ---------------------------------------------------------------------------4-104 Removing the Duplex Feed Unit -------------------------------------------- 4-105

Preparations ------------------------------------------------------------------------------4-105 Procedure ----------------------------------------------------------------------------------4-105

Removing the Cassette Pickup Roller -------------------------------------4-107 Removing the Cassette Separation Pad ----------------------------------4-108 Removing the Multi-purpose Pickup Roller -------------------------------4-108 Removing the Multi-purpose Separation Pad----------------------------4-109

Adjustment

Scanning System Adjustment ----------------------------------------------5-2

Procedure After Replacing the Reader Scanner Unit (the Contact

Sensor) ------------------------------------------------------------------------------- 5-2 Procedure After Replacing the Copyboard Glass-------------------------- 5-2

Procedure After Replacing the Reader Unit --------------------------------- 5-2 Procedure After Replacing the ADF Unit ------------------------------------- 5-2

Electrical Adjustment ---------------------------------------------------------5-3

Procedure After Replacing the Main Controller Board-------------------- 5-3

Trouble Shooting

Test Print ------------------------------------------------------------------------6-2

Test Pages --------------------------------------------------------------------------- 6-2

Engine-test Page --------------------------------------------------------------------------- 6-2 Controller Test Print ----------------------------------------------------------------------- 6-2

Trouble Shooting Items ------------------------------------------------------6-3

Image Defects ---------------------------------------------------------------------- 6-3

Light Print ------------------------------------------------------------------------------------- 6-3 Dark Print ------------------------------------------------------------------------------------- 6-3 Completely Blank --------------------------------------------------------------------------- 6-4 All Black --------------------------------------------------------------------------------------- 6-4

0-6

White Spots ---------------------------------------------------------------------------------- 6-4 Dirt On Back --------------------------------------------------------------------------------- 6-5

Vertical Lines --------------------------------------------------------------------------------- 6-5 Horizontal Lines ----------------------------------------------------------------------------- 6-5

Dirt On Front --------------------------------------------------------------------------------- 6-6 Dropouts -------------------------------------------------------------------------------------- 6-6

Vertical White Lines ------------------------------------------------------------------------ 6-6 Horizontal White Lines -------------------------------------------------------------------- 6-7 Loose Toner ---------------------------------------------------------------------------------- 6-7

Misformed Image --------------------------------------------------------------------------- 6-8 Repetitive Image Defects Ruler --------------------------------------------------------- 6-8

Adjustment of Fixing System ---------------------------------------------------- 6-8

Nip-width Specications------------------------------------------------------------------- 6-8

Version Up ----------------------------------------------------------------------6-9

Overview ----------------------------------------------------------------------------- 6-9

Overview of Upgrading -------------------------------------------------------------------- 6-9

Preparation -------------------------------------------------------------------------- 6-9

Necessary System Environment -------------------------------------------------------- 6-9

Before Downloading the System Software ------------------------------------------6-10

Downloading the System Software -------------------------------------------6-10

Downloading the System ----------------------------------------------------------------6-10

Error Codes

Error Code ----------------------------------------------------------------------7-2 Fax

Error Code -------------------------------------------------7-4

Outline -------------------------------------------------------------------------------- 7-4

Error Code Outline ------------------------------------------------------------------------- 7-4

User Error Code -------------------------------------------------------------------- 7-4

User Error Code ----------------------------------------------------------------------------- 7-4

Service Error Code ---------------------------------------------------------------- 7-5

Service Error Code ------------------------------------------------------------------------- 7-5

Service Mode

Outline ---------------------------------------------------------------------------8-2

Outline of Service Mode ---------------------------------------------------------- 8-2 Using the Mode --------------------------------------------------------------------- 8-3

Default Settings ----------------------------------------------------------------8-3

Service Mode Menus ------------------------------------------------------------- 8-3

Service Soft Switch Settings (SSSW) ------------------------------------8-7

Outline -------------------------------------------------------------------------------- 8-7

Bit Switch Composition -------------------------------------------------------------------- 8-7

SSSW-SW01: ----------------------------------------------------------------------- 8-7

List of Functions ----------------------------------------------------------------------------- 8-7

Detailed Discussions of Bit 0 ------------------------------------------------------------ 8-7

SSSW-SW03 ------------------------------------------------------------------------ 8-7

List of Functions ----------------------------------------------------------------------------- 8-7 Detailed Discussions of Bit 7 ------------------------------------------------------------ 8-7

SSSW-SW04 ------------------------------------------------------------------------ 8-8

List of Functions ----------------------------------------------------------------------------- 8-8 Detailed Discussions of Bit 2 ------------------------------------------------------------ 8-8 Detailed Discussions of Bit 3 ------------------------------------------------------------ 8-8 Detailed Discussions of Bit 4 ------------------------------------------------------------ 8-8 Detailed Discussions of Bit 6 ------------------------------------------------------------ 8-8 Detailed Discussions of Bit 7 ------------------------------------------------------------ 8-8

SSSW-SW05 ------------------------------------------------------------------------ 8-9

List of Functions ----------------------------------------------------------------------------- 8-9 Detailed Discussions of Bit 1 ------------------------------------------------------------ 8-9 Detailed Discussions of Bit 2 ------------------------------------------------------------ 8-9

SSSW-SW12 ------------------------------------------------------------------------ 8-9

List of Functions ----------------------------------------------------------------------------- 8-9

SSSW-SW13 -----------------------------------------------------------------------8-10

List of Functions ----------------------------------------------------------------------------8-10 Detailed Discussions of Bit 2 -----------------------------------------------------------8-10

SSSW-SW14 -----------------------------------------------------------------------8-10

List of Functions ----------------------------------------------------------------------------8-10 Detailed Discussions of Bit 2 -----------------------------------------------------------8-10 Detailed Discussions of Bit 4 -----------------------------------------------------------8-10

SSSW-SW18 -----------------------------------------------------------------------8-11

List of Functions ----------------------------------------------------------------------------8-11 Detailed Discussions of Bit 0 -----------------------------------------------------------8-11 Detailed Discussions of Bit 1 -----------------------------------------------------------8-11

SSSW-SW25 -----------------------------------------------------------------------8-11

List of Functions ----------------------------------------------------------------------------8-11 Detailed Discussions of Bit 0 -----------------------------------------------------------8-11 Detailed Discussions of Bit 2 -----------------------------------------------------------8-11

0-7

SSSW-SW28 -----------------------------------------------------------------------8-12

List of Functions ----------------------------------------------------------------------------8-12 Detailed Discussions of Bit 0 -----------------------------------------------------------8-12 Detailed Discussions of Bit 1 -----------------------------------------------------------8-12 Detailed Discussions of Bit 2 -----------------------------------------------------------8-12 Detailed Discussions of Bit 3 -----------------------------------------------------------8-12 Detailed Discussions of Bit 4 -----------------------------------------------------------8-12 Detailed Discussions of Bit 5 -----------------------------------------------------------8-12

SSSW-SW30 -----------------------------------------------------------------------8-12

List of Functions ----------------------------------------------------------------------------8-12 Detailed Discussions of Bit 5 -----------------------------------------------------------8-12

Menu Switch Settings (Menu) -------------------------------------------- 8-13

Menu Switch Composition ------------------------------------------------------8-13 <No.005 NL equalizer> ----------------------------------------------------------8-13 <No.006 telephone line monitor> ---------------------------------------------8-13 <No.007 ATT transmission level> ---------------------------------------------8-13 <No.008 V.34 modulation speed upper limit> -----------------------------8-13 <No.009 V.34 data speed upper limit> --------------------------------------8-13 <No.010 Frequency of the pseudo CI signal> -----------------------------8-13

Numeric Parameter Settings (Numeric Param.) --------------------- 8-14

Numerical Parameter Composition -------------------------------------------8-14

<002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN transmission condition (3)> -------------------8-14 <005: NCC pause length (pre-ID code)> -----------------------------------8-14 <006: NCC pause length (post-ID code)> ----------------------------------8-15 <010: line connection identication length> --------------------------------8-15 <011: T.30 T1 timer (for reception)> ------------------------------------------8-15 <013: T.30 EOL timer> -----------------------------------------------------------8-15 <016: time length to rst response at time of fax/tel switchover> ----8-15 <017: pseudo RBT signal pattern ON time length><018: pseudo RBT signal pattern OFF time length (short)><019: pseudo RBT signal pattern OFF time length (long)> ---------------------------------------------------------8-15 <020: pseudo CI signal pattern ON time length><021: pseudo CI signal pattern OFF time length (short)><022: pseudo CI signal pattern OFF time length (long)> ----------------------------------------------------------------8-15 <023: CNG detention level for fax/tel switchover> -----------------------8-15

<024: pseudo RBT transmission level at time of fax/tel switchover> 8-15 <025: Answering machine connection function signal detection time> ---

8-16

<027: V.21 low-speed ag preamble identication length> ------------8-16 <056 - 061: Count type select > -----------------------------------------------8-16

Scanner Function Settings (Scanner) ---------------------------------- 8-19

Numeric Parameter Functional Conguration -----------------------------8-19 <031Vertical scan start position adjustment> ------------------------------8-19 <033Vertical scan magnication correction>-------------------------------8-19 <035: - 036:Reader motor speed change> ---------------------------------8-20 <041: Vertical scan start position adjustment (when scanning on a document fed from ADF)> ------------------------------------------------------8-20 <047: Vertical scan magnication correction (when scanning on a document fed from ADF)> ------------------------------------------------------8-20 <048: Horizontal scan magnication correction (when scanning on a document fed from ADF)> ------------------------------------------------------8-20

Printer Function Settings (Printer) --------------------------------------8-20

Service Soft Switch Settings (SSSW) ---------------------------------------8-20

SSSW-SW15 -------------------------------------------------------------------------------8-20

Numeric Parameter Settings (NUMERIC Param.) ------------------------8-20

<034: Left-end registration adjustment (malti-purpose tray)> ------------------8-20 <035: Left-end registration adjustment (cassette)> -------------------------------8-20 <039: Left-end registration adjustment (duplex unit)> ----------------------------8-21 <053: Margin adjustment at the leading edge of the copy> ---------------------8-21 <054: Margin adjustment at the trailing edge of the copy> ---------------------8-21 <055: Margin adjustment at the right edge of the copy> ------------------------8-21 <056: Margin adjustment at the left edge of the copy> -------------------------8-21

Setting of System Functions (System) --------------------------------- 8-21

Bit Switch Settings ----------------------------------------------------------------8-21

Counter Indication (Counter) ---------------------------------------------8-22

Counters ----------------------------------------------------------------------------8-22 Clearing Counters ----------------------------------------------------------------8-22

Report Output (Report) ---------------------------------------------------- 8-22

Report Output ----------------------------------------------------------------------8-22

System Data List ------------------------------------------------------------------8-23 System Dump List ----------------------------------------------------------------8-23

0-8

Counter List ------------------------------------------------------------------------8-24 Spec List ----------------------------------------------------------------------------8-25

Data Initialization Mode (Clear) ------------------------------------------ 8-26

Clear ---------------------------------------------------------------------------------8-26

Rom Management (Rom) -------------------------------------------------8-26

ROM Display -----------------------------------------------------------------------8-26

Test Mode (Test) ------------------------------------------------------------- 8-26

Overview ----------------------------------------------------------------------------8-26

Outline ----------------------------------------------------------------------------------------8-26

DRAM Test -------------------------------------------------------------------------8-28

D-RAM Test<(1) D-RAM TEST> -------------------------------------------------------8-28

Scan Test ---------------------------------------------------------------------------8-29

Scan Test ((2) SCAN TEST) ------------------------------------------------------------8-29

Print Test ----------------------------------------------------------------------------8-29

Print Test ((3) PRINT TEST) ------------------------------------------------------------8-29

Modem Test ------------------------------------------------------------------------8-30

Modem Test ((4) MODEM TEST) ------------------------------------------------------8-30

Faculty Test -------------------------------------------------------------------------8-32

Function Test <(6) FUNCTION TEST> -----------------------------------------------8-32

Cleaning Mode --------------------------------------------------------------------8-35

Roller Cleaning Mode ((0) ROLLER CLEAN) --------------------------------------8-35

Appendex

Service Tools --------------------------------------------------------------------- II Solvents and Oil List ----------------------------------------------------------- II General Timing Chart ----------------------------------------------------------III

General Timing Chart --------------------------------------------------------------- III

General Circuit Diagram ------------------------------------------------------IV

General Circuit Diagram (TYPE I) -----------------------------------------------IV General Circuit Diagram (TYPE II) -----------------------------------------------V

CDRH Provisions Laser Safety

Toner Safety

Notes When Handling A

Battery Notes On Assembly/ Disassembly

■

MF6600/D1100 Series

F-0-2F-0-2

Safety Precautions

0-2

Safety Precautions > Laser Safety > Handling Laser Scanner Unit

CDRH Provisions

Food and Drug CDRH (Center for Devices and Radiological Health) under FDA (Food and

Drug Administration) enforced provisions of the section for laser and laser products on August

2, 1976. These provisions are applicable to all laser products manufactured or assembled after August 1, 1976 and allow only products certied their compliance with the provisions to market in the US. Each product shall have afxed the applicable label as shown below to follow the labeling requirements prescribed in CDRH provisions.

Note that the wording included in labels is different depending on laser product classications.

CAUTION:

Note that the wording included in labels is different depending on laser product classications.

Laser Safety

About Laser Beams

Laser radiation may be hazardous to human. The laser scanner unit mounted in this device is

sealed in the protective housing and the external cover to prevent laser beams from leaking

to the environment. As long as the device is operated under normal conditions, users are

safely arded from laser leaks.

Handling Laser Scanner Unit

Before providing service works for the laser scanner unit and its peripherals, ensure to turn off the power of the device. Any cover with potential dangers of laser beam reection has afxed the caution label at the position shown in the gure below.

[1]

F-0-3F-0-3

0-3

Safety Precautions > Notes On Assembly/Disassembly

Toner Safety

About Toner

Toner is a nontoxic matter composed of plastic, iron and a trace of pigments.

Never throw toner in ames to avoid explosion.

CAUTION:

Never throw toner in ames to avoid explosion.

Handling Adhered Toner

Use dry tissue paper to wipe off toner adhered to skin or clothes and wash in water. Never use warm water for cleaning up toner to prevent toner particles from being gelated to soak into bers permanently. Toner particles are reactive with vinyl polymers. Avoid contacting these materials.

Notes When Handling A Battery

CAUTION:

Risk Of Explosion If Battery Is Replaced By An Incorrect Type.

Dispose Of Used Batteries According To The Instructions.

The following warnings are given to comply with Safety Principles (EN60950).

CAUTION:

Wenn mit dem falschen Typ ausgewechselt, besteht Explosionsgefahr.

Gebrauchte Batterien gemäß der Anleitung beseitigen.

•

Notes On Assembly/Disassembly

Follow the items below to assemble/disassemble the device.

1. Disconnect the power plug to avoid any potential dangers during assembling/disassembling works.

2. If not specially instructed, reverse the order of disassembly to reinstall.

3. Ensure to use the right screw type (length, diameter, etc.) at the right position when

assembling.

4. To keep electric conduction, binding screws with washers are used to attach the grounding wire and the varistor. Ensure to use the right screw type when assembling.

5. Unless it is specially needed, do not operate the device with some parts removed.

6. Never remove the paint-locked screws when disassembling.

CAUTION

DOUBLE POLE/NEUTRAL FUSING

F-0-4F-0-4

Product Overview

Product Lineups

Product Features Specications Name of Parts

■

1-2

Product Overview > Product Lineups > Main Unit

Product Lineups

MEMO:

This product has two model types according to the country: TYPE I and TYPE II. The way of distinguishing TYPE I and TYPE II is written in the Label [1] inside the

Cartridge Cover.

120-127V

TYPE II

Serial No. ETNXXXXX

120-127V

Serial No. ETNXXXXX

[1]

TYPE II

TYPE I

Be sure to check the type, and then refer to the Service Manual.

F-1-1F-1-1

Main Unit

Function Canon i-SENSYS

Series

Canon imageCLASS Series

MF6680dn D1120 D1150 D1170 D1180

Appearance

Copy O O O O O Print O O O O O Fax O - O O O

USB Scan - - - - Network Scan O O O O O Remote UI O O O O O

DADF O O O O O Automatic 2-sided Print O O O O O

F-1-2F-1-2

T-1-1T-1-1

1-3

Product Overview > Product Features > Features > Power-saving MFP

Options

[2]

[1]

No. Name Description Remarks

[1] Canon Cassette Feeding Unit-U1 Approx. 500 Sheets (Plain paper

80g/ m2)

[2] TELEPHONE 6 KIT Long cord Cool White

MF6680dn

F-1-3F-1-3

T-1-2T-1-2

Product Features

Features

Compact MFP

The product compactied with lower height.

450mm

464mm

High-speed MFP

This compact A4 color MFP can prints at high speeds of up to 30 pages per minute (A4/LTR).

Power-saving MFP

This product employed SURF xing method with a ceramic heater and 3W sleep mode to achieve electric power saving.

■

F-1-4F-1-4

1-4

Product Overview > Specications > Main Unit Specications

Specications

Main Unit Specications

Item Specication/function

Body Desktop (DADF standard type)

Light Source Type LED

Photosensitive Medium OPC drum Image Reading Method Contact Sensor Reading Method Reproduction Method Indirect electrostatic copying method Exposure Method Semiconductor laser Charging Method Roller contact charging method Development Method Dry system - element jumping development method Transfer Method Roller transfer method

Separation Method

Electrostatic separation (neutralizing needle) and curvature separation

Pickup Method

Cassette pick-up: 1 cassette

Multi manual feeding pick-up Cassette Pickup Method Pad separation method Multifeeder Pickup Method Pad separation method Drum Cleaning Method Rubber blade Fixing Method On-demand Toner Type Magnetic negative toner Toner Supply Type By drum style toner cartridge Toner Save Mode Yes Original Type Sheets, books, solids (up to 2 kg)

Maximum Original Size

Fixed: 216mm x 356mm

ADF: 216mm x 356mm

Reproduction Ratio Zoom: 0.50 to 2.00 (specied by the percent)

Warm-up Time

16.0 seconds or less*

(temperature: 20 deg C, humidity: 65%; from when the machine

turns ON the main power switch until the standby display appears)

* Warm-up time may diff er depending on the condition and

environment of the machine. Reading Resolution

<TEXT/PHOTO>: 300 dpi x 600 dpi

<TEXT>, <PHOTO>, <TEXT/PHOTO+>: 600 dpi x 600 dpi

Printing Resolution 600 x 600 dpi First Print Time 6 seconds or less (A4/LTR)

Item Specication/function

First Copy Time 8 seconds or less (A4/LTR) Print Speed Approximately 30 sheets / minute (A4/LTR)

Cassette Paper Size

LTR, LGL, A4, B5, A5, Executive, Ocio, Brazil-Ocio, MexicoOcio, FLSP, A-FLS, Government-LTR, Government-LGL

Multifeeder Paper Size 76 × 127 to 216 × 356 mm

Cassette Paper Type

Plain Paper (80g / m2), Plain Paper (60 to 80 g/m2) recycled paper (64 to 80 g/m2), Color (64 g/m2), Heavy Paper 1 (90 to 120 g/m2),

Multifeeder Tray Paper Type

Plain Paper (80g / m2), Plain Paper (60 to 80 g/m2), recycled paper (64 to 80 g/m2), Color (64 g/m2), Heavy Paper 1 (90 to 150 g/m2), Heavy Paper 2 (151 to 163 g/m2), Transparency, Labels, Envelopes

Cassette Capacity 500 sheets (80g / m2) Multifeeder Tray Capacity 50 sheets (80g / m2) Delivery Tray Stack 65 sheets (60 - 80g / m2) Continuous Reproduction 1 to 99 sheets Duplex Method Auto Duplexing

Life of Cartridge Approx.5000 sheets (Starter Cartridge:Approx.2,300 sheets) Interface Standard:USB2.0, option:No Hard Disk Standard:No, option:No

Memory 128MB Energy Save Mode

Yes. (Manual ON / OFF, automatically OFF after a set period of time, automatically ON when receiving facsimile / print data)

Operating Environment (Temperature Range)

10 to 30 degrees C

Operating Environment

(Humidity Range)

20 to 80 %

Operating Environment (Atmospheric Pressure)

0.16 to 1.01 hPa (0. 6 to 1 bar)

Power Supply Rating

120V-127V (60Hz) 220-240V, 50/60Hz

Power Consumption

(Maximum)

Maximum consumption: Less than 1090 W

Power Consumption

During operation: approximately 550W or less (reference value) At standby: approximately 18W (referenve velue)In sleep mode:

approximately 3W (reference value) Dimensions 464 mm (H) × 472 mm (D) × 450 mm (W) Weight Approximately 20.6 kg (including the toner cartridge)

Network Yes

1-5

Product Overview > Specications > FAX Specications

Item Specication/function

PDL BDL-Image, PCL5 / PCLXL SEND Yes

ADF Specications

Item Specication/function

Original position center reference Original processing mode

1-sided to 1-sided copy, 2-sided to 2-sided copy, 1-sided to 2-sided copy, 2-sided to 1-sided copy

Original reading stream reading method Stack A4/LTR: 50 sheets, LGL: 30 sheets Mixed original sizes Yes Original AE detection No Original size recognition No Stamp No Operating environment pursuant to the host machine

T-1-3T-1-3

T-1-4T-1-4

FAX Specications

Item Specication/function

Suitable Line Public Switched Telephone Network (PSTN)

Up to 28.8Kbps in modem speed is currently available in PSTN. Note

that available modem speed is telephone-line dependent.

Telephone line connection: 1

Communication Protocol Super G3 Modulation Method Image modulation : V.34/V.8/V.17/V.29/V.27ter

Transmission procedure : V.21

Transmission Speed 33,600 bps Coding Compression method: JBIG, MMR, MR, MH Error Correction ECM Minimum Receivable Input

Level

V.17, V.27ter, V.29: -6 to -43 dBm V.34: -10 to -43 dBm

Modem IC CONEXANT DFX336

Scanning Line Density Normal : 8 dots/mm x 3.85 lines/mm

Fine : 8 dots/mm x 7.7 lines/mm Super ne : 8 dots/mm x 15.4 lines/mm Ultra ne : 16 dots/mm x 15.4 lines/mm

Half Tone 256 tones

Reproduction Resolution 600 x 600 dpi Receivable Reduction Setting

Automatic reduction: 75-100% (1% increment)

FAX/TEL Switching Available Answering Machine

Transfer Setting

Available

Remote Reception Available Auto-dialing Available Delayed Transmission Available Broadcast Transmission Destinations: up to 201 Dual Access Up to 70 schedules Image Data Backup Available

T-1-5T-1-5

1-6

Product Overview > Specications > Paper types

Print Speed.

(Unit: page/minute)

Paper type

Cassette MP Tray OP Cassette

1-sided 2-sided 1-sided 2-sided 1-sided 2-sided

A4 30 16.4 30 16.4 30 16.4

LTR 30 16.7 30 16.7 30 16.7 LGL 25.3 13.1 25.3 13.1 25.3 13.1

B5 13>12>8>6 - 16>12>8>6 - 10>10>8>6 A5 15>12>8>6 - 17>12>8>6 - 11>11>8>6 -

Strip of paper (90 to 297 mm)

- - 2>1 - - -

Postcard - - 17>12>8>6 - - Envelope - - 17>12>8>6 - - -

T-1-6T-1-6

Paper types

(: available -: not available)

Paper types Printer driver setting Cassette Multi-purpose

Tray

Plain From 16 to 21 lb

(60 to 80 g/m2)

Plain Paper  

From 16 to 21 lb (60 to 80 g/m2)

Plain Paper L  

Color 17 lb (64 g/m2) Color   Recycled* From 17 to 21 lb

(64 to 80 g/m2)

Recycled  

Thick From 24 to 32 lb

(90 to 120 g/m2)

Heavy Paper 1  -

From 24 to 40 lb (90 to 150 g/m2)

- 

From 40 to 43 lb (151 to 163 g/m2)

Heavy Paper 2 - 

Transparency Transparency *1 -  Label Label -  Envelope Envelope - 

*1: Use only LTR or A4 transparencies made especially for this machine.

T-1-7T-1-7

1-7

Product Overview > Name of Parts > External View > Front Side

Paper size

(: available -: not available)

Paper size Cassette Multi-purpose Tray

A4 (210.0 mm × 297.0 mm)   B5 (182.0 mm × 257.0 mm)   A5 (148.0 mm × 210.0 mm)  

Legal (LGL) (215.9 mm × 355.6 mm)   Letter (LTR) (215.9 mm × 279.4 mm)   Executive (EXEC) (184.0 mm × 266.7 mm)   Ofcio (215.9 mm × 317.5 mm)   Brazil Ofcio (215.9 mm × 355.6 mm)   Mexico Ofcio (215.9 mm × 341 mm)   Government Letter (203.2 mm × 266.7 mm)   Government Legal (203.2 mm × 330.2 mm)   FOOLSCAP (215.9 mm × 330.2 mm)   A-FLS (205.7 mm × 337.82mm)   3"×5" to Legal (76 × 127 to 216 mm× 356 mm) - 

T-1-8T-1-8

Name of Parts

External View

Front Side

[10]

[11]

[1] [3]

[4]

[5]

[6]

[7]

[8]

[12] [13]

[14]

[15][16]

[2]

[9]

■

F-1-5F-1-5

1-8

Product Overview > Name of Parts > External View > Rear Side

Key Name Service Pars No. Remarks Reference

[1] DADF (Duplex Automatic

Document Feeder)

- - (Refer to page 4-30)

[2] Slide Guides FC9-1501 Front -

FC9-1502 Rear

[3] Document Feeder Tray FM3-9534 - - [4] Document Delivery Tray - - - [5] Control Panel FM3-9803 (D1180 TYPE I) (Refer to page 4-70)

FM4-6439 (D1180 TYPE II) FM3-9817 (D1170 TYPE I) FM4-6440 (D1170 TYPE II) FM3-9818 (D1150 US,CA,LTN

TYPE I)

FM4-6441 (D1150 US,CA,LTN

TYPE II)

FM4-1649 (D1150 LTN,SG,AU

TYPE I)

FM4-6443 (D1150 LTN,SG,AU

TYPE II)

FM4-1651 (D1150 KR TYPE I) FM4-6445 (D1150 KR TYPE II) FM4-6444 (D1150 CN TYPE II) FM3-9819 (D1120 TYPE I) FM4-6442 (D1120 TYPE II) FM4-1647 (MF6680dn TYPE I) FM4-6446 (MF6680dn TYPE II) FM4-1648 (MF6640dn TYPE I)

[6] Right Cover FC9-2055 - (Refer to page 4-23) [7] Multi-purpose Tray - - - [8] Multi-purpose Tray Extension - - - [9] Slide Guides for Multi-purpose

Tray

- - -

[10] Paper Stopper - - -

[11] Upper Cover FC9-1999 - (Refer to page 4-28) [12] Reader Unit FM3-9525 - (Refer to page 4-35) [13] Open Button - - - [14] Front Cover - - (Refer to page 4-26) [15] Main Power Switch FM4-1656 (TYPE I) -

FM4-5367 (TYPE II)

[16] Paper Cassette FM3-9798 - -

T-1-9T-1-9

Rear Side

[1]

[2]

[3]

[4] [5]

[6]

[7]

[8]

[9]

[10]

Key Name Service Pars No. Remarks Reference

[1] USB Port - - [2] Ethernet Port - - [3] Left Cover FC9-2017 - (Refer to page 4-19) [4] External Device Jack - - [5] Telephone Line Jack - - [6] Left Rear Cover FC9-2020 (FAX Model) (Refer to page 4-22)

FC9-4916 (Except FAX Model) -

[7] Power Socket FM4-1607 (TYPE I) -

FM4-5386 (TYPE II) -

[8] Duplex Unit Cover - - [9] Right Rear Cover FC9-2056 - (Refer to page 4-26)

[10] Rear Cover FM3-9791 - -

■

F-1-6F-1-6

T-1-10T-1-10

1-9

Product Overview > Name of Parts > Cross Sectional View > Printer

Cross Sectional View

ADF/Reader Unit

[1]

[5]

[2] [3]

[4]

Key Name Service Pars No. Reference

[1] ADF Paper Feed Roller FM3-9540 - [2] ADF Separation Roller FL2-6637 (Refer to page 4-39) [3] ADF Pickup Roller FC7-6189 (Refer to page 4-38) [4] ADF Delivery roller FM4-1875 - [5] ADF Separation Pad FC7-6297 (Refer to page 4-41)

■

F-1-7F-1-7

T-1-11T-1-11

Printer

[1]

[11]

[2]

[12]

[3]

[13]

[4]

[14]

[5]

[15]

[6]

[16]

[7]

[17]

[8]

[18]

[9]

[19]

[10]

[20]

Key Name Service Pars No. Reference

[1] Fixing delivery roller - - [2] Face-down delivery roller FM4-1875 - [3] Fixing unit RM1-6405 (120V)

RM1-6406 (230V)

(Refer to page 4-98)

[4] Fixing lm unit - [5] Pressure roller - - [6] Laser scanner unit RM1-6424 (Refer to page 4-93) [7] Copyboard glass (scanning glass) - (Refer to page 4-46) [8] Cartridge - - [9] Registration shutter - -

[10] Registration roller RM1-6419 -

■

F-1-8F-1-8

1-10

Product Overview > Name of Parts > Operation Panel > Send Operation Panel

Key Name Service Pars No. Reference

[11] Multi-purpose tray pickup roller RL1-2120 (Refer to page

4-108)

[12] Multi-purpose tray separation pad RL1-2115 (Refer to page

4-108)

[13] Feed roller - - [14] Cassette pickup roller RM1-6414 (Refer to page

4-106)

[15] Cassette separation pad RM1-6454 (Refer to page

4-107)

[16] Duplex re-pickup roller - - [17] Transfer roller RM1-6450 (Refer to page 4-95) [18] Photosensitive drum - - [19] Duplex feed roller - - [20] Duplex feed unit RM1-6441 (Refer to page

4-104)

Operation Panel

Main Operation Panel

[1] [2] [3] [4] [5]

[10]

[11] [12] [13] [14] [15][6] [7] [8] [9]

[16]

[17]

[18]

[19][20][21][22][23][24][25][26][27][28][29]

Key Name Key Name

[1] Paper Select indicator [16] [Stop/Reset] key [2] [Collate/2 on 1] key [17] [Start] key [3] [Paper Select] key [18] Error indicator [4] [Enlarge/Reduce] key [19] Processing/Data indicator [5] [Menu] key [20] [Tone] key [6] Display [21] [Density] key

■

T-1-12T-1-12

F-1-9F-1-9

Key Name Key Name

[7] [COPY] key [22] [Image Quality] key [8] [SEND/FAX] key (For the D1180/D1170/MF6680dn)

[FAX] key (For the D1150) [SEND] key (For the MF6640dn)"

[23] [+] key

[9] [SCAN] key [24] [OK] key

[10] [Paper Settings] key [25] [-] key

[11] Numeric keys [26] [Job Cancel/Status Monitor] key

[12] [Log In/Out] key (ID key) [27] [View Settings] key [13] [Clear] key [28] [2-Sided] key [14] [Report] key [29] 2-Sided mode indicator [15] [Energy Saver] key

Send Operation Panel

Panel open

[1] [2]

[3][4]

[5] [5]

Key Name Key Name

[1] [Address Book] key [4] [Hook] key [2] [Recall/Pause] key (For the D1180/D1170/MF6680dn)

[Redial/Pause] key (For the D1150)"

[5] [Coded Dial] key

[3] [Coded Dial] key

■

T-1-13T-1-13

F-1-10F-1-10

T-1-14T-1-14

1-11

Product Overview > Name of Parts > Operation Environment of the Printer Driver > Network Specications

Function List

[8]

[7]

[4][2]

[5]

[6]

[3]

[1]

[9]

Key Item Key Item

[1] leading edge of original [6] trailing edge margin [2] left margin [7] non-scanning area [3] effective scanning width [8] scanning range [4] right margin [9] trailing edge of original [5] leading edge margin

Copy Area

Item Size

left margin 5.0 mm right margin 5.0 mm leading edge margin 5.0 mm trailing edge margin 5.0 mm

Reception Print Area

Item Size

left margin 4.0 mm right margin 4.0 mm leading edge margin 5.0 mm trailing edge margin 5.0 mm

■

F-1-11F-1-11

BDL Print Area

Item Size

left margin 5.0 mm right margin 5.0 mm leading edge margin 5.0 mm trailing edge margin 5.0 mm

PCL Print Area

Item Size

left margin 4.2 mm right margin 4.2 mm leading edge margin 4.2 mm trailing edge margin 4.2 mm

Operation Environment of the Printer Driver

Operation environment

Microsoft Windows 98/98SE/Me, Windows 2000 Server, Windows 2000 Professional, Windows XP Professional, Windows XP Home Edition, Windows Server 2003, Windows Vista, Windows 7, MacOS X v10.2.8 or later

Hardware environment

- IBM PC or IBM compatible PC

- CD-ROM drive or network environment accessible to CD-ROM

- PC equipped with USB port and installed with USB class driver

Network Specications

Name Item

Connector RJ45 Interface Ethernet II Communication Speed 10Base-T/100Base-TX Communication Mode FULL DUPLEX/half DUPLEX Supported Protocol TCP/IP

■

1-12

Product Overview > Name of Parts > Operation Environment of the Printer Driver > SEND Specications

SEND Specications

The Send function is available for the MF6680dn/D1170/D1180.

Send to le server

Communication Protocol SMB (TCP/IP) Data Format TIFF (B&W), PDF (B&W), JPEG (Color), PDF (Compact) (Color) Resolution 100 x 100 dpi, 150 x 150 dpi, 200 x 100 dpi, 200 x 200 dpi, 300 x 300

dpi, 400 x 400 dpi, 600 x 600 dpi

System Environment Windows 2000 Server/Professional (SP1 or later), Windows XP

Professional/Home Edition, Windows Vista, Windows 7, Windows Server 2003, Windows Server 2008, Mac OS X, Red Hat Linux 7.2

Interface 100BASE-TX, 10BASE-T Color Mode Color, B&W (black and white) Original Type Text, Text/Photo, Photo

E-mail Communication Protocol SMTP, POP3 Resolution 100 x 100 dpi, 150 x 150 dpi, 200 x 100 dpi, 200 x 200 dpi, 300 x 300

dpi, 400 x 400 dpi, 600 x 600 dpi

Format TIFF (B&W), PDF (B&W), JPEG (Color), PDF (Compact) (Color) Original Size LTR, LGL, STMTR, STMT, A4, A5, B5

Server Software Microsoft Exchange Server 5.5 (SP2), Sendmail 8.11.2, Lotus Domino

R4.5/R5

Facsimile

Applicable Line Public Switched Telephone Network (PSTN)*1

Compatibility G3 Data Compression Schemes MH, MR, MMR, JBIG Modem Speed 33.6 Kbps

Automatic fallback

Transmission Speed Approx. 3 seconds/page*2 at 33.6 Kbps, ECM-MMR,

transmitting from the memory Transmission/Reception Memory

Maximum approx. 512 pages*2

(total pages of transmission/reception) Fax Resolution FINE: 203 pels/inch x 196 lines/inch (8 pels/mm x 7.7 lines/mm)

PHOTO: 203 pels/inch x 196 lines/inch (8 pels/mm x 7.7 lines/mm)

SUPER FINE: 203 pels/inch x 392 lines/inch (8 pels/mm x 15.4 lines/

mm)

ULTRA FINE: 406 pels/inch x 392 lines/inch (16 pels/mm x 15.4 lines/

mm)

STANDARD: 203 pels/inch x 98 lines/inch (8 pels/mm x 3.85 lines/

mm)

■

T-1-15T-1-15

T-1-16T-1-16

T-1-17T-1-17

Technical Overview

Technical

Overview

Basic Conguration

Document Exposure/ feeder System Engine Control System Laser Scanner System Image-formation System Fixing Unit System Media Feed System

■

2-2

Technical Overview > Basic Conguration > Basic Sequence > Basic Operational Sequence

Basic Conguration

Conguration Function

This device is roughly composed of the 6 functional blocks as shown in the gure below

Document Exposure/Delivery System

•

Image Formation System

•

Controller System

•

Fixing System

•

Laser Exposure System

•

Pickup / Feed System

•

Engine controller

Casette

Laser scanner

MP Tray

Cartridge

Transfer roller

Laser beam Paper flow Signal flow

Fixing unit

Delivery unit

ADF unit

Contact Sensor

Main

Controller

Laser Exposure System

Image Formation System

Pickup / Feed System

Fixing System

Controller system

Document exposure/delivery system

Photosensitive drum

F-2-1F-2-1

Basic Sequence

Basic Operational Sequence

The CPU on the DC Controller PCB controls the operational sequence. The table below shows the operation and the purposes in each status from start-up of the device and to last rotation after print job completion.

Status Operation

WAIT (Wait)

Interval from power-ON

or reactivation from sleep mode upon shutting the door(s) to entering the printready status

Activate the printer to be ready for printing. During WAIT

time, the following operations are done: pressure is applied to the pressure roller of the Fixing Unit; check cartridges

and units being in place; move the developing unit to the

home position; and, clean the ITB. When needed, color

displacement is corrected and the image is stabilized.

STBY (STBY)

Interval from the wait

time or the last rotation to issuance of a print command from the main controller or

power-OFF.

Maintain the print-ready status. The printer enters the sleep mode upon receiving a “sleep” command from the main controller during the stand-by status. The printer executes color displacement correction or image stabilization upon

receiving corresponding commands from the main controller. INTR (IINTR)

Interval from issuance of a print command from the main controller during the

stand-by status to warming up the Fixing Unit to the

target temperature.

To make the printer ready for print jobs, activate high-

voltage bias PCBs, the Laser Scanner Unit and the Fixing

Unit.

PRINT (Print)

Interval from the initial rotation to completion of last

page xation.

Based on the video signals input from the main controller,

form the static latent image on the photosensitive drum to

transfer and x the toner image on paper. When a certain

pages are printed after power-ON, the device undergoes

color displacement correction and/or image stabilization.

LSTR (Last

rotation)

Interval from print job

completion to Motor deactivation.

The last page of the print job is completely delivered. In

this status, the Laser Scanner Unit and high-voltage bias

PCBs are inactive. The printer starts the initial rotation upon

receiving a print command from the main controller during

this status.

■

T-2-1T-2-1

2-3

Technical Overview > Basic Conguration > Basic Sequence > Print Sequence

Print Sequence

Timing chart two consecutive prints on LTR paper

Cassette pickup solenoid (SL201) Main Fan (FM201)

Transfer Charging Bias

Fixing Heater (H201/H2010)

Primary Charging Bias (DC) Developing Bias

Main Motor (M201) Primary Charging Bias (AC)

Laser Diode BD Output signal (BDO)

Print start command (EEC12) Scanner Motor (M202)

Operation

TOP sensor (PS204) Fixing delivery sensor (PS915)

Power switch ON

WAIT

STBY

INTR

LASTR STBY

19 20

17 18

15 16

13 14

11 12

7 8

5 6

3 4

1 2

■

2-4

Technical Overview > Basic Conguration > Print Mode

Print Mode

Print modes Feeding speed Media type Print speed Remarks

Normal speed mode

1/1speed Speed for plain paper A4 width (60

to 90g) Transparencies

30 ppm

1/2 speed mode 1/2 speed Plain paper A4 width

(60 to 90g)

Plain paper less than A4 width (60

to 90g)

Heavy paper (90 to 150g) Heavy paper (151 to 163g)

Bond paper (60 to 104g) Bond paper (105 to 163g)

Label paper Postcard, Tab paper

Envelope

15 ppm

*1: Normal mode is recommended for Neenah Bond 60g/m2

T-2-2T-2-2

+ 197 hidden pages

Canon mf6600 Series, D1100 Series Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Safety Precautions

CDRH Provisions

Laser Safety

About Laser Beams

Handling Laser Scanner Unit

Toner Safety

About Toner

Handling Adhered Toner

Notes When Handling A Battery

Notes On Assembly/Disassembly

Product Overview

Product Lineups

Main Unit

Options

Product Features

Features

Compact MFP

High-speed MFP

Power-saving MFP

Print Speed.

Paper types

Paper size

Name of Parts

External View

Front Side

Rear Side

Cross Sectional View

ADF/Reader Unit

Printer

Operation Panel

Main Operation Panel

Send Operation Panel

Function List

Copy Area

Reception Print Area

BDL Print Area

PCL Print Area

Operation Environment of the Printer Driver

Operation environment

Hardware environment

Technical Overview

Basic Sequence

Basic Operational Sequence

Print Sequence

Print Mode