Canon iR5870C, iR5870Ci, iR6870C, iR6870Ci f-im-6652-000

PUNCHER UNIT-L1/M1/N1/P1 INSTALLATION PROCEDURE

パンチャユニット・L1 設置手順書

Follow the instructions in this booklet when installing the Puncher Unit to its Finisher-Q1/-Q3/

-R1/-T1/-Y1/-AA1, Saddle Finisher-Q2/-Q4/-R2/-T2/-Y2/-AA2.

フィニッシャ・Q1・Q3・R1・T1・Y1・AA1、サドルフィニッシャ・Q2・Q4・R2・T2・ Y2・AA2 にパンチャユニットを取り付ける際は、この手順に従ってください。

ENGLISH

日　　本　　語

PUB. F-IM-6652-000 PRINTED IN JAPAN or CHINA

1.1 Making Pre-Checks

1.1.1 Checking the Contents

- Finisher-Q1/-Q3, Saddle Finisher-Q2/-Q4

[9]

- Finisher-R1, Saddle Finisher-R2

[13]

[12]

[10]

[5]

[12]

[8]

[7]

[11]

[12]

[4]

[10]

[6]

[1]

[13]

[3]

[13]

[2]

F-1-1

[9]

[13]

[4]

[12]

[10]

F-1-2

— 2 —

[5]

[11]

[6]

[1]

[13]

[3]

[10]

[12]

[7]

- Finisher-T1, Saddle Finisher-T2

[9]

[5]

[11]

- Finisher-Y1, Saddle Finisher-Y2

[13]

[12]

[9]

[13]

F-1-3

[8]

[11]

[1]

[13]

[3]

[10]

[5]

[12]

[7]

[12]

[4]

[10]

[1]

[3]

F-1-4

— 3 —

[6]

[13]

[2]

- Finisher-AA1, Saddle Finisher-AA2

[13]

[9]

[5]

[12]

[10]

[11]

[12]

[10]

[7]

[6]

[1]

[13]

[3]

F-1-5

[1] Punch front lower cover 1 pc. [8] Surface cover 1 pc.*1

[2] Punch front lower extension cover 1 pc.*1 [9] Mounting stepped screw (M4X4) 2 pcs.

[3] Punch front lower cover fixing plate 1 1 pc. [10] Stepped screw (M4X5) 2 pcs.

[4] Punch front lower cover fixing plate 2 1 pc.*2 [11] Stepped screw (M4X10) 2 pcs.

[5] Punch Jam Removal label 1 pc. [12] Screw (binding; M4X6) 5 pcs.*3

[6] Punch fixing plate

1 pc.*5 [13] Screw (tapping; M4X2) 3 pcs.*4

(front; FC5-4098)

[7] Punch fixing plate

1 pc.*5

(rear; FC5-4076)

*1: Only for the Finisher-Q1/-Q3/-Y1, Saddle Finisher-Q2/-Q4/-Y2.

*2: Only for the Finisher-Q1/-Q3/-R1/-Y1.

*3: 4 pc. used if for the Saddle Finisher-Q2/-Q4/-R2/-Y2/-AA2.

Only 1 screw is used for the Finisher-T1 and the Saddle Finisher-T2.

*4: 2 pc. used if for the Finisher-R1/-T1/AA1, Saddle Finisher-R2/-T2/-AA2.

*5: It is not used for the Finisher-T1 or the Saddle Finisher-T2. The special fixing plate included in the package of

the finisher is used for them.

— 4 —

1.1.2 Installation Procedure for Accessories (iR C6800 Series, iR C3100

Series, iR C3170/C2570 Series)

If you are installing the puncher unit at the same time as any other accessories, install the host machine, and start in

the following order:

<Installing the Finisher-R1, Saddle Finisher-R2 to an iR C6800 Series Device; Installing the Finisher-Q1 or -

Q3, Saddle Finisher-Q2 or -Q4 to an iR C3100 Series, iR C3170/C2570 Series Device>

Or-

Accessory Documentation

der

1 Side paper deck Side Paper Deck Installation Procedure yes yes

2 Finisher [1], [2] this book; up to "Preparing the Host Ma-

chine for Installation"

3 Relay unit [3], buffer

path unit [4]

5 Finisher Additional

Tray-A1 [5]

6 Puncher unit [6] this book yes yes

7 Connection to host

machine

Finisher/Saddle Finisher Installation Proce-

dure; "Installing the Rely Delivery Unit and

the Buffer Path Unit"

Finisher Additional Tray-A1 Installation

Procedure

this book; "Connecting to the Host Ma-

chine" and thereafter

[1]

iR C6800

Series

yes yes

no yes

yes yes

iR C3100 Series, iR

C3170/C2570 Series

[5]

[2]

[6]

[4]

[3]

F-1-6

— 5 —

ON/OFF

Be sure to perform the following in the sequence indicated on the device before starting the installation work:

1. Turn off the control panel power switch.

2. Turn off the main power switch.

3. Disconnect the power cable (from the power outlet).

Turning Off the Main Power

Be sure to go through the following steps before turning off the main power to avoid damage to the device's hard disk:

1. Hold down the control panel power switch for 3 sec or more.

2. Follow the instructions appearing on the display so that the main power switch may be turned off.

3. Turn off the main power switch.

4. Disconnect the power cable (from the power outlet).

[1]

[2]

[3]

F-1-7

— 6 —

[4]

1.1.3 Installation Procedure for the Accessories (iR4570/3570 Series,

iR2870/2270 Series)

If you are installing the puncher unit at the same time as any other accessories, install the host machine and then start

in the following order:

Order Accessory Documentation

1 Side paper deck Side Paper Deck Installation Procedure

2 Finisher [1], [2] this book; up to "Preparing the Host Machine for Installation"

3 3 Way Unit-A1 [3]* 3 Way Unit-A1 Installation Procedure

4 Buffer path unit [4] Finisher/Saddle Finisher Installation Procedure; "Installing the

Buffer Path Unit"

5 Finisher Additional Tray-B1 [5] Finisher Additional Tray-B1 Installation Procedure

6 Puncher unit [6] this book

7 Connection to host machine this book; "Connecting to the Host Machine" and thereafter

* Some models come with the 3 Way Unit-A1 as standard.

[1]

[5]

[2]

[6]

[4]

[3]

F-1-8

— 7 —

Turning Off the Main Power

Go through the following steps when turning off the main power to avoid damage to the device's hard disk:

1. Hold down the control panel power switch for 3 sec or more.

2. Follow the instructions appearing on the display so that the main power switch may be turned off.

3. Turn off the main power switch.

4. Disconnect the power cable (from the power outlet).

[1]

N/O

F-1-9

[4][3][2]

— 8 —

1.1.4 Installation Procedure for the Accessories (iR6570/5570 Series)

If you are installing the puncher unit at the same time as any other accessories, install the host machine and start in

the following order:

Order Accessory Documentation

1 Side paper deck Side Paper Deck Installation Procedure

2 Finisher [1], [2] this book; up to "Preparing the Host Machine for Installation"

3 Puncher unit [3] this book

4 Connection to host machine this book; "Connecting to the Host Machine" and thereafter

[1]

[2]

[3]

F-1-10

— 9 —

ON/O

Turning Off the Main Power

Be sure to go through the following steps before turning off the main power to avoid damage to the device's hard disk:

1. Hold down the control panel power switch for 3 sec or more.

2. Follow the instructions appearing on the display so that the main power switch may be turned off.

3. Turn off the main power switch.

4. Disconnect the power cable (from the power outlet).

[1]

[2] [3] [4]

F-1-11

— 10 —

1.1.5 Installation Procedure for the Accessories (iR C3380/2880 Series)

If you are installing the puncher unit at the same time as any other accessories, install the host machine and then start

in the following order:

Order Accessory Documentation

1 Side paper deck Side Paper Deck Installation Procedure

2 Buffer path unit [1] Finisher/Saddle Finisher Installation Procedure; "Installing the

Buffer Path Unit"

3 Finisher [2], [3] this book; up to "Preparing the Host Machine for Installation"

4 Puncher unit [4] this book

5 Connection to host machine this book; "Connecting to the Host Machine" and thereafter

[2]

[3]

[4]

[1]

F-1-12

Before starting the installation, perform the following steps in order on the host machine side.

1. Turn off the control panel power switch.

2. Turn off the main power switch.

3. Disconnect the power cable (from the power outlet).

— 11 —

1.1.6 Sequence of installing options (imagePRESS C1 Series)

When installing the puncher unit together with options, after installing the host machine, install options in the fol-

lowing order after installing the host machine.

Order Accessory Documentation

1 Side paper deck Side Paper Deck Installation Procedure

2 Finisher [1], [2] this book; up to "Preparing the Host Machine for Installation"

3 Puncher unit [3] this book

4 Connection to host machine this book; "Connecting to the Host Machine" and thereafter

[1]

[3]

[2]

F-1-13

Before starting the work, be sure to go through the following on the host machine in strict sequence:

1. Turn off the control panel power switch on the host machine.

2. Turn off the main power switch on the host machine.

3. Disconnect the power cable of the host machine from the outlet.

— 12 —

1.2 Unpacking and Checking the Components

1.3 Installation Procedure

1.3.1 Installation Procedure (Fin-

1.2.1 Unpacking

MEMO:

The machine is fitted with tape and cushioning mate-

rial to protect against vibration and shock during tran-

sit. Be sure to remove all of it as instructed before the

installation work. It is a good idea to store away the re-

moved tape and cushioning material for possible fu-

ture relocation and shipment for repairs.

1) Remove the attachments and the puncher unit from

the shipping box.

2) Remove the tape from the outside of the puncher

unit.

3) Open the punch upper cover.

4) Remove the 2 fixing screws [1] each, and detach the

front and rear punch fixing plates [2].

[1]

isher-Q1/-Q3, Saddle FinisherQ2/-Q4)

1. Detaching the Finisher from the Host Machine

If the host machine is equipped with a finisher, you will have to detach the finisher before installing the puncher unit. If you are installing the puncher unit at the same time as a finisher, perform the instructions under "Preparing the Finisher" in the Finisher Installation Procedure and go to "2. Connecting to the Finisher" herein.

1) Turn off the host machine, and disconnect the power plug (from the power outlet).

2) Disconnect the interface cable [1] of the finisher from the host machine.

F-1-14

[2]

[1]

F-1-15

3) In the case of a Finisher-Q1/-Q3, remove the screw [1], and detach the lower front extension cover [2]. Remove the screw [3], and detach the front foot cover [4].

[2]

[1]

[3]

[4]

F-1-16

— 13 —

4) Remove/open the front cover.

<Finisher-Q1/-Q3>

Open the front door [1], and remove the 3 screws [2];

then, detach the front cover [3].

[1]

[2]

[3]

[2]

F-1-17

5) In the case of a Finisher-Q1/-Q3, remove the

stepped screw [1] used to join the finisher to the

host machine.

Open the front cover [1].

[1]

F-1-18

[1]

F-1-19

6) Remove the screw [1], and detach the small cover

[2] at the upper rear of the finisher; then, remove the

stepped screw [3], and disconnect the finisher from

the host machine at the rear.

[2]

[1]

[3]

— 14 —

F-1-20

7) In the case of a Saddle Finisher-Q2/-Q4, close the

front cover. In the case of a Finisher-Q1/-Q3,

mount the front cover using 3 screws.

8) In the case of a Saddle Finisher-Q2/-Q4, remove

the 2 screws [1], and detach the lower front exten-

sion cover [2]. Remove the screw [3], and detach

the front foot cover [4]. Remove the screw [5], and

detach the rear foot cover [6].

[5]

[6]

[2]

[1]

2. Connecting the Finisher

1) In the case of a Finisher-Q1/-Q3, remove the 2

screws [1], and detach the inlet guide [2]; then, re-

move the 4 screws [3], and detach the right cover

[4].

[4]

[3]

[2]

[3]

[1]

F-1-23

[3]

[4]

[1]

F-1-21

9) Remove the 2 screws [1] each, and detach the fixing

plate (front) [2] and the other fixing plate (rear) [3].

[3]

[1]

[2]

F-1-22

If the rubber sheet that comes with the buffer path unit is found attached to the pickup face of the finisher, leave it as it is. If you need to attach a rubber sheet newly, be sure it has not been used before.

2) Fit 2 stepped mounting screws [1] (M4X4) to the

pickup assembly of the finisher.

<Finisher-Q1/-Q3>

[1]

F-1-24

— 15 —

[1]

F-1-25

3) Route the connector cable [1] of the puncher unit to

the rear, and hold it as shown. Hook the hole [2] of

the joint on the 2 stepped mounting screws.

4) Secure the puncher unit to the finisher using 2

stepped screws [1] (M4x10).

[1]

F-1-28

5) Detach the rear cover of the finisher.

<Finisher-Q1/-Q3>

Remove the 3 screws [1], and detach the rear cover

[2].

[2]

[1]

[2]

F-1-26

In the case of a Finisher-Q1/-Q3, the joint would like-

ly interfere. Be sure to hook the puncher unit [2] in

place while keeping the upper cover [1] of the finisher

open.

[1]

[2]

[1]

F-1-29

Detach the cable cover [1], and remove the 6 screws

[2]; then, detach the rear cover [3].

[3]

[1]

F-1-27

[2]

F-1-30

— 16 —

6) Remove the screw [1], and detach the upper rear

(small) cover [2] of the finisher. (Skip this step if it

has already been removed.)

7) Cut off the face cover using nippers.

<Finisher-Q1/-Q3>

[3]

[2]

[1]

F-1-31

<Finisher-Q1/-Q3>

Connect it to the connectors J705 [1] and J706 [2] of

the finisher controller PCB.

[2]

[1]

F-1-33

<Finisher-Q2/-Q4>

Connect it to the connectors J804 [1] and J805 [2] of

the saddle drive PCB; then, route the connector cable

through the 2 cable clamps [3], and fix it in place.

[2]

[1]

[3]

[2]

[1]

F-1-32

8) Securely fit the connector cable of the puncher unit

to the 2 connectors on the PCB of the finisher.

[3]

F-1-34

9) If the rubber sheet [1] that comes with the buffer

path unit is not already attached, attach it by refer-

ring to the marking [2] found on the right side of the

puncher unit.

[2]

[1]

Check to be sure that the connector is in firm contact.

If the puncher unit malfunctions after installation, dis-

connect and then connect the connector and run a

check.

F-1-35

— 17 —

10) Mount the finisher's rear cover.

11) Mount the rear small cover of the finisher using a

screw.

12) In the case of a Finisher-Q1/-Q3, mount the punch

lower front fixing plate 2 [1] to the foot at the front

of the finisher using a screw [2] (binding; M4X6).

MEMO:

In the case of a Saddle Finisher-Q2/-Q4, the punch

lower front cover fixing plate 2 comes mounted. (Its

shape is different from the punch lower front cover

fixing plate 2 of the Finisher-Q1/-Q3.)

3. Preparing the host machine

Mount the fixing plate that comes with the puncher

unit before connecting the finisher to the host ma-

chine. If the finisher has already been installed and if

you have performed the steps in "Detaching the Fin-

isher from the host machine," perform only step 2)

herein.

1) Cut off the face cover of the host machine.

<Connecting the Finisher-Q1/-Q3 or the Saddle

Finisher-Q2/-4 to an iR C3100 Series or iR C3170/

C2570 Series Device>

1-1) Remove the 4 screws [1], and detach the iR host

machine's left cover [2]; then, cut off the face

covers ([3], [4]) with nippers. Remove the rear

left cover [5], and cut off the face cover [6] with

nippers. Mount the left cover and the rear left

cover.

[1]

[2]

F-1-36

13) In the case of a Saddle Finisher-Q2/-Q4, mount

the lower front extension stay [1] using 2 screws [2]

(binding; M4X6). (If found mounted, skip this

step.)

[2]

[1]

[6]

[5]

[4]

[1]

[2]

[3]

F-1-38

<Connecting the Finisher-Q3 or the Saddle Finish-

er-Q4 to an iR4570/3570 Series, iR2870/2270 Se-

ries Device>

1-1) Open the upper front cover [1].

F-1-37

F-1-39

— 18 —

1-2) Remove the rubber face [1].

1-3) Remove the binding screw [2].

1-4) Remove the RS tightening screw [3].

1-5) Remove the front cover unit [4] by moving it in

the direction of the arrow.

F-1-40

1-6) Remove the 4 screws [1], and detach the left cov-

er [2] of the host machine.

1-7) Cut off the face cover [3] of the left cover using

nippers.

1-8) Cut off the face [5] of the inside rear cover (low-

er) [4] using nippers.

1-9) Cut off the face cover [7] of the rear left cover [6]

using nippers.

1-11) Mount the front cover [3] using 2 screws [2];

then, fit the rubber piece [1].

Be sure to slide it to the right so that the claw of the

front cover will match the device.

F-1-42

1-12) Close the upper front cover [1].

[7]

[6]

[5]

[1]

[2]

[1]

F-1-41

1-10) Mount the left cover.

[4]

[3]

F-1-43

2) Mount the fixing plate (front; FC5-4098) [1] and

the other mounting plate (rear; FC5-4076) [2] using

2 screws [3] (binding; M4X6) each.

[2]

[3]

[1]

F-1-44

— 19 —

4. Connecting to the host machine

Check to make sure that the iR is off and its power

plug is disconnected from the power outlet.

1) Remove the 3 screws [1], and detach the rear cover

[2] of the puncher unit.

5) Mount the punch lower front cover fixing plate 1 [1] to the punch lower front cover [2] using a screw [3] (self-tapping; M4X12).

6) Mount the punch lower front extension cover [4] to the punch lower front cover using a screw [5] (selftapping; M4X12).

[2]

[1]

[3]

[2]

[1]

F-1-45

2) Fit the face cover [1] that comes with the unit.

3) Connect the host machine and the puncher unit, and

secure it in place to the fixing plates (front, rear) us-

ing a stepped screw [2] (M4X5; 1 pc. each).

[2]

[1]

[2]

F-1-46

[5]

[4]

F-1-47

7) Fit the positioning pin [1] fitted to the punch lower front cover into the hole of the punch lower front cover [2]; then, mount the punch lower front cover.

[1]

[2]

F-1-48

8) Open the upper front punch cover [1], and fix the punch lower front cover [2] in place using a screw [3] (self-tapping; M4X12).

[3]

4) Mount the rear cover of the puncher unit using 3

screws.

[1]

[2]

F-1-49

— 20 —

1.3.2 Installation Procedure (Finisher-Y1, Saddle Finisher-Y2)

1. Detaching the Finisher from the Host Machine

4) Remove/open the front cover.

<Finisher-Y1>

Open the front door [1], and remove the 3 screws [2];

then, detach the front cover [3].

1) Turn off the host machine, and disconnect the pow-

er plug (from the power outlet).

2) Disconnect the interface cable [1] of the finisher

from the host machine.

[1]

F-1-50

[1]

[2]

[3]

[2]

F-1-52

Open the front cover [1].

[1]

3) In the case of a Finisher-Y1, remove the screw [1],

and detach the lower front extension cover [2]. Remove the screw [3], and detach the front foot cover [4].

[2]

[1]

[3]

[4]

F-1-51

F-1-53

— 21 —

5) In the case of a Finisher-Y1, remove the stepped

screw [1] used to join the finisher to the host ma-

chine.

[1]

F-1-54

8) In the case of a Saddle Finisher-Y2, remove the 3

screws [1], and detach the lower front cover [2].

Remove the screw [3], and detach the rear foot cov-

er [4]. Remove the screw [5], and detach the caster

cover [6].

[3]

[4]

[5]

[6]

[2]

[1]

6) Remove the screw [1], and detach the small cover

[2] at the upper rear of the finisher; then, remove the

stepped screw [3], and disconnect the finisher from

the host machine at the rear.

[2]

[1]

[3]

[1]

F-1-56

9) Remove the 2 screws [1] each, and detach the fixing

plate (front) [2] and the other fixing plate (rear) [3].

[3]

[1]

[2]

[1]

F-1-57

F-1-55

7) In the case of a Saddle Finisher-Y2, close the front

cover. In the case of a Finisher-Y1, mount the front

cover using 3 screws.

— 22 —

2. Connecting the Finisher

<Finisher-Y1>

1) Remove the 2 screws [1], and detach the inlet guide

[2]; then, remove the 4 screws [3], and detach the

right cover [4].

[4]

[3]

[2]

2) Fit 2 stepped mounting screws [1] (M4X4) to the

pickup assembly of the finisher.

<Finisher-Y1>

[1]

[3]

[1]

F-1-58

1) Remove the 2 screws [1], and detach the right front

cover [2].

[1]

[2]

F-1-59

F-1-60

[1]

F-1-61

3) Route the connector cable [1] of the puncher unit to

the rear, and hold it as shown. Hook the hole [2] of

the joint on the 2 stepped mounting screws.

— 23 —

[1]

[2]

F-1-62

In the case of a Finisher-Y1, the joint would likely in-

terfere. Be sure to hook the puncher unit [2] in place

while keeping the upper cover [1] of the finisher open.

[1]

[2]

F-1-63

4) Secure the puncher unit to the finisher using 2

stepped screws [1] (M4x10).

Detach the cable cover [1], and remove the 6 screws

[2]; then, detach the rear cover [3].

[3]

[1]

[2]

F-1-66

6) Remove the screw [1], and detach the upper rear

(small) cover [2] of the finisher. (Skip this step if it

has already been removed.)

7) Cut off the face cover using nippers.

<Finisher-Y1>

[1]

F-1-64

5) Detach the rear cover of the finisher.

<Finisher-Y1>

Remove the 3 screws [1], and detach the rear cover

[2].

[2]

[3]

[2]

[1]

F-1-67

[1]

F-1-65

— 24 —

[3]

[2]

<Finisher-Y2>

Connect it to the connectors J804 [1] and J805 [2] of

the saddle drive PCB; then, route the connector cable

through the 2 cable clamps [3], and fix it in place.

[1]

F-1-68

8) Securely fit the connector cable of the puncher unit

to the 2 connectors on the PCB of the finisher.

Check to be sure that the connector is in firm contact.

If the puncher unit malfunctions after installation, dis-

connect and then connect the connector and run a

check.

[2]

[1]

[3]

F-1-70

9) If the rubber sheet [1] that comes with the buffer

path unit is not already attached, attach it by refer-

ring to the rib [2] found on the right side of the

puncher unit.

[2]

[1]

<Finisher-Y1>

Connect it to the connectors J705 [1] and J706 [2] of

the finisher controller PCB.

[2]

[1]

F-1-69

F-1-71

10) Mount the finisher's rear cover.

11) Mount the rear small cover of the finisher using a

screw.

— 25 —

12) In the case of a Finisher-Y1, mount the punch low-

er front fixing plate 2 [1] to the foot at the front of

the finisher using a screw [2] (binding; M4X6).

MEMO:

In the case of a Saddle Finisher-Y2, the punch lower

front cover fixing plate 2 comes mounted. (Its shape is

different from the punch lower front cover fixing plate

2 of the Finisher-Y1.)

3. Preparing the host machine

Mount the fixing plate that comes with the puncher

unit before connecting the finisher to the host ma-

chine. If the finisher has already been installed and if

you have performed the steps in "Detaching the Fin-

isher from the host machine," perform only step 2)

herein.

1) Cut off the face cover of the host machine.

<Connecting the Finisher-Y1 or the Saddle Finish-

er-Y2 to an iR C3380/2880 Series Device>

1-1) Remove the 4 screws [1], and detach the iR host

machine's left cover [2]; then, cut off the face

covers ([3], [4]) with nippers. Remove the rear

left cover [5], and cut off the face cover [6] with

nippers. Mount the left cover and the rear left

cover.

[1]

[2]

F-1-72

13) In the case of a Saddle Finisher-Y2, mount the

lower front extension stay [1] using 2 screws [2]

(binding; M4X6). (If found mounted, skip this

step.)

[1]

[2]

[6]

[5]

[4]

[1]

[3]

[2]

[1]

F-1-74

F-1-73

— 26 —

2) Mount the fixing plate (front; FC5-4098) [1] and

the other mounting plate (rear; FC5-4076) [2] using

2 screws [3] (binding; M4X6) each.

[2]

[3]

2) Fit the face cover [1] that comes with the unit.

3) Connect the host machine and the puncher unit, and

secure it in place to the fixing plates (front, rear) us-

ing a stepped screw [2] (M4X5; 1 pc. each).

[2]

[1]

[3]

[1]

F-1-75

4. Connecting to the host machine

Check to make sure that the iR is off and its power

plug is disconnected from the power outlet.

1) Remove the 3 screws [1], and detach the rear cover

[2] of the puncher unit.

[2]

F-1-77

4) Mount the rear cover of the puncher unit using 3

screws.

5) Mount the punch lower front cover fixing plate 1 [1] to the punch lower front cover [2] using a screw [3] (self-tapping; M4X12).

6) Mount the punch lower front extension cover [4] to the punch lower front cover using a screw [5] (selftapping; M4X12).

[2]

[1]

[3]

F-1-76

[1]

[5]

[4]

F-1-78

— 27 —

7) Fit the positioning pin [1] fitted to the punch lower front cover into the hole of the punch lower front cover [2]; then, mount the punch lower front cover.

[1]

[2]

F-1-79

1.3.3 Installation Procedure (Finisher-R1/-T1/-AA1, Saddle Finisher-R2/-T2/-AA2)

1. Detaching the Finisher from the Host Machine

If the host machine is already equipped with a finish-

er, you need to detach the finisher before starting to in-

stall the puncher unit. If you are planning to install the

puncher unit at the same time as the finisher, perform

the instructions in "Preparing the Finisher for Installa-

tion" and then those in "2. Connecting to the Finisher."

8) Open the upper front punch cover [1], and fix the punch lower front cover [2] in place using a screw [3] (self-tapping; M4X12).

[3]

[1]

[2]

F-1-80

1) Turn off the host machine, and disconnect the pow-

er plug (from the power outlet).

2) Disconnect the interface cable [1] of the finisher

from the host machine.

<Finisher-R1, Saddle Finisher-R2>

Free the interface cable [1] from the cable clamp [2].

[1]

[2]

F-1-81

— 28 —

<Finisher-T1, Saddle Finisher-T2>

[1]

F-1-82

<Finisher-R1>

Open the front door [1], and remove the 3 screws [2];

then, detach the front cover [3].

[1]

[2]

[3]

<Finisher-AA1, Saddle Finisher-AA2>

(The illustration shows the Saddle Finisher-AA2.)

[1]

F-1-83

3) In the case of a Finisher-R1, remove the screw [1],

and detach the front foot cover [2].

[2]

F-1-85

<Finisher-T1/-AA1, Saddle Finisher-R2/-T2/-AA2>

Open the front door[1]. (The illustration shows the

Saddle Finisher-R2.)

[1]

F-1-86

[1]

[2]

F-1-84

4) Remove/open the front cover.

— 29 —

+ 66 hidden pages