Canon ES100 User Manual

Specifications

ES100

Series

Pickup Device: 1/3 inch interline

transfer CCD

Picture Element: 510x492(/E,EIA)

500x580(/C,CCIR)

Horizontal resolution: 420 TV lines Sensitivity: 0.04 lux/F=1.2 S/N ratio: Over 48 dB Electronic shutter: Up to 1/10,000 Auto. Iris: Video Drive BLC: Yes AGC ON/OFF: Yes Gamma Correction: 0.45 Video output: 1.0Vp-p,75 ohm Power source: AC 198 ~ 264V Sync. Mode: Internal Sync. Lens Mount: C or CS with Ring Dimension: 42x47x100mm

Operating Temperature: -10 Storage Temperature: -40

C to +50oC

C to +70oC

MES1G00100

INSTRUCTION MANUAL

1/3" B/W CCD Cameras

General

The ES100 Series Cameras are compact, full performance, general purpose B/W CCD Cameras, which use high sensitive 1/3" B/W interline transfer CCDs (Charge Coupled Device). ES100, with AC power cord , has functions of ES on/off, AGC on/off , and BLC on/off. Audio feature is built-in.

II.

Precautions

• Do not expose the camera to humidity and dust. If the camera is mounted outdoor, a camera housing is required.

• Do not disassemble it or place it on an unstable b ase.

• Do not touch the surface of CCD senso r by hand directly. When the camera is not in use, pu t the cover cap on the lens mount.

• Never face the camera toward the sun.

• Use Auto-iris lens or N.D. filter or set large F number of manual lens when the light intensity is very high, in order to protect the sensitive CCD sensor.

• Use proper AC power source otherwise the camera will not function correctly.

III

Installation Instructions

Remove the cover cap from the top of the lens mount.

If CS mount lens is used, please also remove the C Mount Ring

(the 5mm thick ring on top of the lens mount). Screw the lens firmly onto the lens mount.

Connect the video output of the camera to a B/ W monitor or other

video device through a 75 ohm type coaxial cable with BNC female connector at camera end.

Plug the power c o rd to the outlet. Power indicator LED s hould

light if the power source is properly connected. Once the image appear s on the monitor, adjust the focus and

diaphragm of the lens to obtain the best picture. If the subject is not in focus when adjusting focus of the lens, do

back focus adjustment as follo wing:

i. Set the focus ring of the lens to infinity position. ii. Take picture of subject at a distance more than 20m

away from the camera.

iii. Loosen the lens mount fixing screw located at

bottom of the front panel by using the L wrench.

iv. Turn the lens and the mount together so that the

subject is in focus.

v. Secure the lens moun t fixing screw firmly again.

Mount the camera on th e mounting bracket b y u sing the mounting

(

hole at bottom of the front panel. If top mounting is required, fix the top mount ing base on top of the camera with two screws and then mount camera to mounting bracket.

IV.

Using Special Features

) Using Auto Iris Lens

IRIS

AUDIO

For ES100, ple as e use video drive iris lens. Wire the cable of lens to Mini Plug according to the following table:

Pin1 Pin2 Pin3 Pin4 +12V VD-IRIS GND GND

VIDEO

E.S.

AGC

OFF

BLC

) Electronic Shutter ON/OFF

ES ON: The camera continuously adjusts the shutter speed from 1/60

(EIA),1/50 (CCIR) second to 1/10,000 second acc ord ing to the luminance conditions of the scene.

ES OFF: The shutter speed is fixed at 1/60 (EIA),1/50 (CCIR) second. Set ES OFF, when auto iris lens is used or flicker is observed under a very

bright fluorescent la m p. Otherwise, turn ES on for opti mum performance.

) Automatic Gain Control ON/OFF

AGC ON: The sensitivity increases automatically when light is low. AGC OFF: A low-noise picture is obtained under a low light conditi on.

) Back Light Compensa tion

When BLC is turn on, the AGC, ES and IRIS operating point is determined by averaging over the center area instead of entire field-ofview, so that a dimly-lit foregro und o bject at center area can be cle ar l y distinguis hed from brightly-lit ba ckgrounds. BLC should not be used unless it is needed to co mpensate for back-lit.

III