The EOS 70D (N) does not have the Wi-Fi functions explained in
this manual.
ENGLISH
EOS 70D (W)
EOS 70D (N)
Introduction
The EOS 70D (W/N) is a digital single-lens reflex camera featuring a
fine-detail CMOS sensor with approx. 20.2 effective megapixels, DIGIC
5+, high-precision and high-speed 19-point AF (all cross-type focusing),
approx. 7.0 fps continuous shooting, Live View shooting, Full HighDefinition (Full HD) movie shooting, and Wi-Fi function*.
* The EOS 70D (N) does not have the Wi-Fi function.
Before Starting to Shoot, Be Sure to Read the Following
To avoid botched pictures and accidents, first read the “Safety
Precautions” (p.445-447) and “Handling Precautions” (p.18-19).
Refer to This Manual while Using the Camera to Further
Familiarize Yourself with the Camera
While reading this manual, take a few test shots and see how they
come out. You can then better understand the camera.
Testing the Camera Before Use and Liability
After shooting, play images back and check whether they have been
properly recorded. If the camera or memory card is faulty and the
images cannot be recorded or downloaded to a computer, Canon
cannot be held liable for any loss or inconvenience caused.
Copyrights
Copyright laws in your country may prohibit the use of your recorded
images or copyrighted music and images with music in the memory
card for anything other than private enjoyment. Also be aware that
certain public performances, exhibitions, etc., may prohibit photography
even for private enjoyment.
2
Compatible Cards
In this manual, “card” refers to SD memory cards, SDHC memory
cards, and SDXC memory cards.
* The camera does not come with a card for recording images/
movies. Please purchase it separately.
The camera can use the following cards regardless of capacity:
• SD memory cards
• SDHC memory cards*
• SDXC memory cards*
* UHS-I cards supported.
Cards that Can Record Movies
When shooting movies, use a large-capacity card with a fast reading/
writing speed as shown in the table.
Compression Method (p.265)Card
IPB6 MB/sec. or faster
ALL-I (I-only)20 MB/sec. or faster
If you use a slow-writing card when shooting movies, the movie may
not be recorded properly. Also, if you play back a movie on a card
with a slow reading speed, the movie may not play back properly.
If you want to shoot still photos while shooting a movie, you will need
an even faster card.
To check the card’s reading/writing speed, refer to the card
manufacturer’s website.
3
Item Check List
Battery Pack
LP-E6
(with protective cover)
Battery Charger
LC-E6/LC-E6E*
Interface Cable
Camera
(with body cap)
Wide Strap
Before starting, check that all the following items have been included
with your camera. If anything is missing, contact your dealer.
* Battery Charger LC-E6 or LC-E6E is provided. (The LC-E6E comes with a
power cord.)
The Instruction Manuals and DVD/CD-ROMs provided are listed on the next
page.
If you purchased a Lens Kit, check that the lenses are included.Depending on the Lens Kit type, a lens instruction manual may also be
included.
Be careful not to lose any of the above items.
4
Instruction Manuals and DVD/CD-ROMs
Basic Instruction
Manual
Wi-Fi Function
Instruction Manual*
(Basic)
The instruction manual consists of booklets and electronic manuals
(PDF files on the DVD-ROM). Basic operations are explained in the
booklets. For detailed instructions on all functions and operations,
see the detailed version manuals on the DVD-ROM.
Image review timeÎ p.60Single-image displayÎ p.290Shooting information
displayÎ p.292
Index displayÎ p.296Image browsing
(Jump display)Î p.297
Magnified viewÎ p.298Image rotateÎ p.301RatingÎ p.302Movie playbackÎ p.308Slide showÎ p.312Viewing images on a
TV setÎ p.316
ProtectÎ p.320EraseÎ p.322Touch playbackÎ p.299
Image Editing
RAW image processing Î p.328ResizeÎ p.333Creative filtersÎ p.335
Printing
PictBridgeÎ p.345Print Order (DPOF)Î p.355Photobook Set-upÎ p.359
Customization
Custom Functions (C.Fn) Î p.362Custom ControlsÎ p.383My MenuÎ p.389Custom shooting mode Î p.390
Sensor Cleaning and Dust
Reduction
Sensor cleaningÎ p.340Append Dust Delete Data Î p.341
Software
OverviewÎ p.457InstallationÎ p.459
Wi-Fi*
Wi-FiÎ Separate booklet
* The EOS 70D (N) does not have the
Wi-Fi function.
17
Handling Precautions
Camera Care
This camera is a precision instrument. Do not drop it or subject it to physical shock.
The camera is not waterproof and cannot be used underwater. If you
accidentally drop the camera into water, promptly consult the nearest Canon
Service Center. Wipe off any water droplets with a dry and clean cloth. If the
camera has been exposed to salty air, wipe it with a well-wrung wet cloth.
Never leave the camera near anything having a strong magnetic field such
as a magnet or electric motor. Also avoid using or leaving the camera near
anything emitting strong radio waves, such as a large antenna. Strong
magnetic fields can cause camera misoperation or destroy image data.
Do not leave the camera in excessive heat, such as in a car in direct
sunlight. High temperatures can cause the camera to malfunction.
The camera contains precision electronic circuitry. Never attempt to
disassemble the camera yourself.
Do not block the mirror operation with your finger, etc. Doing so may cause a
malfunction.
Use a blower to blow away dust on the lens, viewfinder, reflex mirror, and
focusing screen. Do not use cleaners that contain organic solvents to clean
the camera body or lens. For stubborn dirt, take the camera to the nearest
Canon Service Center.
Do not touch the camera’s electrical contacts with your fingers. This is to
prevent the contacts from corroding. Corroded contacts can cause camera
misoperation.
If the camera is suddenly brought in from the cold into a warm room,
condensation may form on the camera and internal parts. To prevent
condensation, first put the camera in a sealed plastic bag and let it adjust to
the warmer temperature before taking it out of the bag.
If condensation forms on the camera, do not use the camera. This is to avoid
damaging the camera. If there is condensation, remove the lens, card and
battery from the camera, and wait until condensation has evaporated before
using the camera.
If the camera will not be used for an extended period, remove the battery
and store the camera in a cool, dry, well-ventilated location. Even while the
camera is in storage, press the shutter button a few times once in a while to
check that the camera is still working.
Avoid storing the camera where there are chemicals that result in rust and
corrosion such as in a chemical lab.
18
Handling Precautions
Contacts
If the camera has not been used for an extended period, test all its functions
before using it. If you have not used the camera for some time or if there is
an important shoot such as a foreign trip coming up, have the camera
checked by your Canon dealer or check the camera yourself and make sure
it is working properly.
If you use continuous shooting, Live View shooting, or movie shooting for a
prolonged period, the camera may become hot. This is not a malfunction.
LCD Panel and LCD Monitor
Although the LCD monitor is manufactured with very high precision
technology with over 99.99% effective pixels, there may be a few dead pixels
displaying only black or red, etc. among the remaining 0.01% or less pixels.
Dead pixels are not a malfunction. They do not affect the images recorded.
If the LCD monitor is left on for a prolonged period, screen burn-in may occur
where you see remnants of what was displayed. However, this is only
temporary and will disappear when the camera is left unused for a few days.
The LCD monitor display may seem slow in low temperatures, or look black
in high temperatures. It will return to normal at room temperature.
Cards
To protect the card and its recorded data, note the following:
Do not drop, bend, or wet the card. Do not subject it to excessive force,
physical shock, or vibration.
Do not touch the card’s electronic contacts with your fingers or anything
metallic.
Do not affix any stickers, etc., on the card.Do not store or use the card near anything having a strong magnetic field,
such as a TV set, speakers, or magnet. Also avoid places prone to having
static electricity.
Do not leave the card in direct sunlight or near a heat source.Store the card in a case.Do not store the card in hot, dusty, or humid locations.
Lens
After detaching the lens from the camera, put down the
lens with the rear end up and attach the lens caps to avoid
scratching the lens surface and electrical contacts.
19
Nomenclature
Speaker
(p.308)
Body cap (p.40)
<F> Remote control terminal (p.184)
<D>
HDMI mini OUT terminal (p.316)
<q/C>
Audio/video OUT/Digital terminal
(p.319/346, 455)
<Y> External microphone IN terminal (p.269)
Lens lock pin
Lens mount
Contacts (p.19)
Mirror (p.182, 343)
Depth-of-field preview button
(p.163)
DC coupler cord hole
(p.400)
Grip
(Battery
compartment)
Red-eye
reduction/
Self-timer lamp
(p.190/113)
Remote control
sensor (p.184)
Shutter button
(p.45)
<6> Main Dial
(p.46)
<B> AF area
selection mode button
(p.104)
<U> LCD panel
illumination button
(p.49)
<q> Metering mode
selection button (p.165)
<i>
ISO speed
setting button (p.120)
<R> Drive mode selection button (p.111)
<f> AF mode selection button (p.100)
LCD panel (p.22)
EF lens mount index (p.40)
Built-in flash/AF-assist beam (p.188/203)
Flash sync contacts
Hot shoe (p.193)
Microphone (p.269)
Mode Dial lock-release
button (p.46)
Mode Dial (p.24)
Strap mount
(p.27)
<D> Flash button (p.188)
Lens release
button (p.41)
EF-S lens mount index (p.40)
20
Nomenclature
/
<V> Focal plane mark
<A/k> Live View shooting/
Movie shooting switch (p.215/251)
<0> Start/Stop button (p.216, 252)
Multi function lock warning (L)
No card/card error warning (Card)
Card full warning (FuLL)
Error code (Err)
AF point selection
(
Aperture (p.162)
<A> Highlight tone priority (p.145)
Exposure level indicator
Exposure compensation amount (p.167)
AEB range (p.168)
Red-eye reduction lamp-on indicator
----
[ ] AF, SEL [ ], SEL AF)
--
The display will show only the settings currently applied.
Warning symbol
(p.376)
<g> ISO speed
(p.120)
<o> Focus confirmation
light (p.73)
Max. burst (p.119)
Number of remaining
multiple exposures (p.177)
ISO speed (p.120)
23
Nomenclature
Basic Zone
All you do is press the shutter button.
The camera sets everything to suit
the subject or scene.
A : Scene Intelligent Auto (p.72)
7 : Flash Off(p.77)
C : Creative Auto (p.78)
8 : Special scene (p.81)
2 : Portrait (p.82)
3 : Landscape (p.83)
4 : Close-up (p.84)
5: Sports (p.85)
6 : Night Portrait (p.86)
F : Handheld Night Scene (p.87)
G : HDR Backlight Control (p.88)
Creative Zone
These modes give you more
control for shooting various
subjects.
d : Program AE (p.158)
s : Shutter-priority AE (p.160)
f : Aperture-priority AE (p.162)
a : Manual exposure (p.164)
F : Bulb (p.171)
Custom shooting mode
You can register the
shooting mode (d/s/f/a/F), AF operation,
menu settings, etc., to w
and shoot (p.390).
Mode Dial
Turn the Mode Dial while holding down the Mode Dial center (Mode Dial
lock release button).
24
Lens
Lens without a distance scale
Hood mount (p.42)
Filter thread
(front of lens)
Zoom ring (p.41)
Image Stabilizer switch (p.43)
Lens mount index (p.40)
Nomenclature
Focusing ring (p.110, 247)
Focus mode switch (p.40)
Zoom position index
Contacts (p.19)
25
Nomenclature
Battery pack slot
Charge Lamp
Power plug
IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS.
DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
CAREFULLY FOLLOW THESE INSTRUCTIONS.
For connection to a supply not in the U.S.A., use an attachment plug adapter
of the proper configuration for the power outlet, if needed.
Power cord
Power cord socket
Battery pack slot
Charge lamp
Battery Charger LC-E6
Charger for Battery Pack LP-E6/LP-E6N (p.28).
Battery Charger LC-E6E
Charger for Battery Pack LP-E6/LP-E6N (p.28).
26
1
Eyepiece cover
Getting Started
This chapter explains preparatory steps before you start
shooting and basic camera operations.
Attaching the Strap
Pass the end of the strap through
the camera’s strap mount eyelet
from the bottom. Then pass it
through the strap’s buckle as shown
in the illustration. Pull the strap to
take up any slack and make sure
the strap will not loosen from the
buckle.
The eyepiece cover is also
attached to the strap (p.183).
27
Charging the Battery
LC-E6
LC-E6E
Remove the protective cover.
1
Detach the protective cover provided
Attach the battery.
2
As shown in the illustration, attach the
To detach the battery, follow the
Recharge the battery.
3
For LC-E6
As shown by the arrow, flip out the
For LC-E6E
Connect the power cord to the
X Recharging starts automatically and
with the battery.
battery securely to the charger.
above procedure in reverse.
battery charger’s prongs and insert
the prongs into a power outlet.
charger and insert the plug into a
power outlet.
the charge lamp blinks in orange.
Charge Level
0-49%
50-74%Blinks twice per second
75% or higherBlinks three times per second
Fully chargedGreenLights up
It takes approx. 2.5 hours to fully recharge a completely exhausted battery at room
temperature (23°C / 73°F). The time required to recharge the battery will vary greatly
depending on the ambient temperature and the battery’s remaining capacity.
For safety reasons, recharging in low temperatures (5°C - 10°C /
41°F - 50°F) will take longer (up to approx. 4 hours).
ColorDisplay
Orange
Charge Lamp
Blinks once per second
28
Charging the Battery
After disconnecting the charger’s power plug, do not touch the prongs for approx. 10 sec.
If the battery’s remaining capacity (p.396) is 94% or higher, the battery
will not be recharged.
The charger cannot charge any battery other than Battery Pack LP-E6/LP-E6N.
Tips for Using the Battery and Charger
Upon purchase, the battery is not fully charged.
Charge the battery before use.
Recharge the battery on the day before or on the day it is to be used.
Even during storage, a charged battery will gradually drain and lose its capacity.
After recharging the battery, detach it and disconnect the
charger from the power outlet.
You can attach the cover in a different
orientation to indicate whether the battery
has been recharged or not.
If the battery has been recharged, attach the
cover so that the battery-shaped hole <> is
aligned over the blue sticker on the battery. If the battery is
exhausted, attach the cover in the opposite orientation.
When not using the camera, remove the battery.
If the battery is left in the camera for a prolonged period, a small amount
of power current is released, resulting in excess discharge and shorter
battery life. Store the battery with the protective cover attached. Storing
the battery when it is fully charged may lower the battery’s performance.
The battery charger can also be used in foreign countries.
The battery charger is compatible with a 100 V AC to 240 V AC 50/60 Hz
power source. If necessary, attach a commercially-available plug adapter for
the respective country or region. Do not attach any portable voltage
transformer to the battery charger. Doing so can damage the battery charger.
If the battery becomes exhausted quickly even after being fully
charged, the battery has reached the end of its service life.
Check the battery’s recharge performance (p.396) and purchase a
new battery.
29
Installing and Removing the Battery
Only Battery Pack LP-E6/LP-E6N can be used.
Load a fully charged Battery Pack LP-E6/LP-E6N into the camera. The
camera’s viewfinder becomes bright when a battery is installed, and
darkens when the battery is removed.
Installing the Battery
Open the cover.
1
Slide the lever as shown by the
arrows and open the cover.
Insert the battery.
2
Insert the end with the battery
contacts.
Insert the battery until it locks in
place.
Close the cover.
3
Press the cover until it snaps shut.
Removing the Battery
Open the cover and remove the
battery.
Press the battery lock lever as shown
by the arrow and remove the battery.
To prevent short circuiting of the
battery contacts, be sure to attach the
provided protective cover (p.28) to
the battery.
30
Loading...
+ 438 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.