Cannon Professional User Manual

PROFESSIONAL 1000
TRADITIONAL 1000
FREESTANDING
GAS COOKER
Use and Installation Instructions
This appliance must be installed in accordance with the regulations in force and
only used in a well ventilated space.
The data badge is fitted on the rear panel. The model/serial number can also be found
Read these instructions before installing or using the appliance and retain
them for future reference.
These instructions are only valid for the countries whose symbols appear in the manual
and on the serial number plate.
CONTENTS
PAGE
Introduction 3
For Your Safety 4
Oven Timer Operation 6
Hotplate 12
Griddle 15
Some recipe ideas for your griddle 16
Grill 17
Ovens 19
Oven Cooking Chart 20
The Slow Cook Setting 22
Care and Cleaning 23
Something wrong with your Cooker? 25
Installation Instructions 27
Guarantee Information 35
Service Information 36
2
INTRODUCTION
To help you make the best use of your cooker, PLEASE READ THIS BOOKLET CAREFULLY. Your new cooker is guaranteed and will give lasting service. The guarantee is only applicable if the cooker has
been installed in accordance with the Installation Instructions. The cooker is designed specifically for domestic installation. When first using the cooker ensure that the room is well ventilated (e.g. open a window or use an extractor fan) and that persons who may be sensitive to the odour avoid any fumes. It is from the room until the smell has ceased. This odour is due to any temporary finish and also any moisture absorbed by the insulation.
Our policy is one of continual improvement in design and development, therefore strict accuracy of illustrations and descriptions cannot be guaranteed.
This appliance conforms to the following EEC directives:
use and responsibility will not be accepted for use in any other
suggested that any pets be removed
Gas Appliances
- 90/396/EEC
Low Voltage Equipment
- 2006/95/EEC
- 93/68/EEC
Electromagnetic Compatibility;
- 89/336/EEC
- 92/31/EEC
- 93/68/EEC
3
FOR YOUR SAFETY
Please read the precautions below before using your cooker.
ALWAYS . . .
ALWAYS make sure you understand the controls before using the cooker.
ALWAYS check that all controls on the cooker are turned off after use.
ALWAYS stand back when opening an oven door to allow heat to disperse.
ALWAYS use dry, good quality oven gloves when removing items from the ovens.
ALWAYS take care when removing items from the top oven/grill when the main oven is on, as the contents may
be hot.
ALWAYS keep the oven and grill doors closed when the cooker is not in use.
ALWAYS place pans centrally over the hotplate burners and position them so that the handles cannot acciden-
tally be caught or knocked or become heated by other burners.
ALWAYS keep the cooker clean, as a build up of grease or fat from cooking can cause a fire.
ALWAYS allow the cooker to cool before cleaning.
ALWAYS follow the basic principles of food handling and hygiene to prevent the possibility of bacterial growth.
ALWAYS keep ventilation slots clear of obstructions.
ALWAYS turn off the electricity supply before cleaning or replacing an oven lamp.
ALWAYS refer servicing to CORGI registered appliance service engineers.
ALWAYS ACCESSIBLE PARTS MAY BECOME HOT WHEN THE GRILL IS USED. YOUNG CHILDREN SHOULD
BE KEPT AWAY.
ALWAYS Children should be supervised to ensure that they do not play with the appliance
ALWAYS During use the appliance
inside the oven
becomes hot. Care should be taken to avoid touching heating elements
4
FOR YOUR SAFETY
NEVER . . .
NEVER leave children unsupervised where the cooker is installed as all surfaces will get hot during and after
use.
NEVER allow anyone to sit or stand on any part of the cooker.
NEVER store items that children may attempt to reach above the cooker.
NEVER heat up unopened food containers as
NEVER store chemicals, food stuffs, pressurised containers in or on the cooker, or in cabinets immediately
above or next to the cooker.
NEVER fill a deep fat frying pan more than 1/3 full of oil, and never use a lid. DO NOT
WHILE COOKING.
NEVER place flammable or plastic items on or near the hotplate.
NEVER use proprietary spillage collectors on the hotplate.
NEVER use the cooker as a room heater.
NEVER dry clothes or place other times over or near to the hotplate or oven/gril doors.
NEVER wear garments with long flowing sleeves whilst cooking.
NEVER operate the grill with the grill doors closed. This may cause overheating of your cooker.
NEVER line the shelves, floor or sides of the oven or grill with aluminium foil as over heating and damage can
result.
NEVER use steam cleaners.
pressure can build up causing the container to burst.
LEAVE UNATTENDED
NEVER touch the heating elements inside the oven or grill even when off.
NOTE: The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed. Always ensure that the kitchen is well ventilated; keep natural ventilation holes open or install a mechanical ventilation device (mechanical
In particular when using the grill or more than one hotplate burner, open a window if a mechanical ventilation device is not operating.
! The appliance should not be operated by people (including children) with reduced physical, sensory or mental capacities, by inexperienced individuals or by anyone who is not familiar with the product. These individuals should, at the very least, be supervised by someone who assumes responsibility for their safety or receive preliminary instructions relating to the operation
extractor hood).
of the appliance.
5
OVEN TIMER OPERATION
The oven timer offers you the following features:
1. Time of Day
2. Automatic C ooking
3. Minute Minder
AUTOMATIC COOKING
The LEFT HAND oven can be controlled automatically.
GUIDANCE ON AUTOMATIC COOKING
1. Select foods which will take the same time to cook.
2. Set the oven timer so that the food has just finished or is just about to finish cooking on your return to the oven. This will ensure the food has not cooled down and does not require reheating before serving.
3. Food
4. Warm food should never be placed in the oven if there is to be a delay period. Stews prepared by frying the
5. Dishes containing left-over cooked poultry or meat, for example Shepherds Pie, should not be cooked automati-
6. Stews and joints should be cooked by the long slow method, so that the delay period is kept to a minimum.
7. On warm days, to prevent harmful bacterial growth in certain foods (ie poultry, joints, etc) the delayed start
8. Wine or beer may ferment and cream may curdle during the delay period, so it is best to add these ingredients
9. Foods which discolour should be protected by coating in fat or tossing in water to which lemon juice has been
10.Dishes containing liquid should not be filled too full to prevent boiling over.
11.Food should be well sealed (but not airtight) in a container to prevent the loss of liquid during cooking. Alu-
12.Ensure food is cooked thoroughly before serving.
should be as cold as possible when it goes into the oven, ideally straight from the refrigerator. Frozen
meat and poultry should be thawed thoroughly before it is put in the oven.
meat and vegetables should be cooked as soon as possible.
cally if there is to be a delay period.
should be kept to a minimum.
just before serving.
added, prior to placing food in the oven.
minium foil gives a good seal.
6
OVEN TIMER OPERATION
A U T
.
000
O
.
000
.
000
A U T
.
000
O
(When the 'AUTO' symbol is flashing, to return the oven to Manual operation, turn the oven controls off, ensure that the correct time of day is set, and press the "Manual" button - The 'AUTO' symbol will go out).
CLOCKFACE
The timer incorporates a 24 hour clock.
Ensure the correct time of day is always set, before using your cooker.
SYMBOLS
A 'bell' symbol will light up when you select a Minute Minder Period and will remain lit for the period set. At the end of symbol will disappear.
The 'cookpot' symbol will light up either:-
- When the timer is in manual mode, or
- During the actual Coo
'AUTO' will light up:-
- When the timer is first turned on it will flash. It will go out when a time of day is set or when the timer is set to manual. The 'AUTO' symbol will flash at the end programme has finished.
the Minute Minder Period, the timer will emit an audible tone and the 'bell'
k Period.
of an Auto Cooking programme to indicate that the
TIMER FUNCTION BUTTONS
Minute Minder Button
Here you can set a time period of up to 23 hours 59 minutes, that will count down. When it reaches zero, the timer will emit an audible tone.
For Example: If you set 20 minutes, the audible tone will
occur 20 minutes later.
AUTO COOKING PROGRAMME
Cook Period Button
Cook Period is the actual length of time for which, the timer will switch the oven(s) on as part of an "Auto Cooking" programme. (e.g. If you set 2 hours, the food will be cooked for 2 hours).
End Time Button
The time of day at which you want an "Auto Cooking" programme to end. For Example: If you set a "Cook Period" for 2 hours, and "End Time" of 11:00. The timer will switch the oven(s) on at 9:00 and turn Cooking Programme has finished.
Notes:
- When setting an Auto Cooking programme you will need to set the oven control(s) to the required temperature(s) when you set the timer.
-If an Auto Cooking programme has been set the oven(s) will only operate during the pre-programmed time.
Manual Button
Needs to be pressed to cancel an Auto Cooking programme and return the oven(s) to Manual operation.
the oven(s) off at 11:00. You will hear a audible tone at 11:00, to indicate that the Auto
"+" and "-" Buttons
Used to adjust the various timer function settings.
7
OVEN TIMER OPERATION
SETTING THE TIME OF DAY
A U T
000
O
A U T
000
O
.
.
.
Step 1 Make sure all oven controls are turned Off.
Step 2 Check the electricity supply to the cooker is turned on.
Step 3 When switched on the display will show 0.00 and the Auto symbol, flashing
intermittently.
Step 4 Press
Step 5 With the Cook Period & End Time buttons still held in, press either the "+" or "-"
buttons to set the correct time of day.
& hold in both the Cook Period & End Time buttons together.
Step 6 Release all the buttons simultaneously. THE TI
To change the time of day repeat Steps 4, 5 & 6 above.
Note: You cannot adjust the time of day if the timer has been set for an Auto Cooking Programme.
ME OF DAY IS NOW SET.
SETTING THE MINUTE MINDER
Step 1 Ensure the time of day is set correctly.
.
000
A U T
.
000
O
Note 1 When the Minute Minder has been set, the time remaining can be checked at any time by simply pressing
the Minute Minder button.
Note 2If necessary the Minute Minder can be cancelled before the tone sounds by pressing and holding the
Minute Minder button and then at the same time pressing window.
Step 2 Press and hold the Minute Minder button. Step 3 With the Minute Minder button held in, set the required Minute Minder period using
the "+" and "-" buttons. A ' Release all buttons and the timer display will revert back to the time of day. The 'bell' symbol will remain lit to signify that a Minute Minder period has been set. At the end
Step 4 To cancel the audible tone press the Minute Minder button.
of the set time an audible tone will be heard, and the 'bell' symbol will disappear.
bell' symbol will light up.
the "-" button until 0.00 appears in the display
8
OVEN TIMER OPERATION
AUTO COOKING PROGRAMMES
There are two Auto Cooking programmes that can be selected using your timer:-
(a) To set the timer to switch the oven(s) On and Off Automatically (b) To set timer to switch on immediately and OFF automatically after a set cook period.
a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY
This allows you to cook at a specified time for a chosen period before the oven switches off Automatically.
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day. Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
.
000
A U T
.
4120
O
A U T
.
6120
O
A U T
.
4120
O
Step 3 Press and hold in the Cook Period button. The display will read 0.00 with the 'cookpot' symbol lit.
Step 4 With the Cook Period button still held in, set the required Cook Period using the "+" and "-" buttons.
Release the bu symbol and 'cookpot' symbol lit.
Step 5 Press and hold in the End Time button. The display will read the earliest possible end time for the Cook P symbol will be lit.
Step 6 With the End Time button still held in, use the "+" and "-" buttons to set the 'End Time' (i.e. The time you Release all the buttons and the timer will revert back to the time of day.
The 'Auto' symbol will remain lit to signify that an Auto Cooking Programme has been set. The 'cookpot' sy
ttons and the timer display will revert to the time of day with the 'Auto'
eriod that you have set above. The 'Auto' symbol and 'cookpot'
require the oven to switch off ).
mbol will go out.
A U T
.
6120
O
.
6120
Step 7 Turn the oven control(s) to the required temperature, and if necessary select the appropriate oven function.
At the end of the Automatic Cook Period the Auto Symbol will flash and an intermittent bleeping sound will be heard. The audible tone will continue unless cancelled. The 'Auto' symbol will continue to flash until the timer is returned to Manual operation (see below).
Step 8 Press the Manual button, returned to Manual.
Step 9 Turn the oven control(s) to the OFF position.
the audible tone will be cancelled and the oven(s) will be
9
OVEN TIMER OPERATION
Note 1 When cooking automatically the Cook Period can be checked at any time by simply pressing the
Cook Period button.
Note 2 When cooking automatically the End Time can be checked at any time by simply pressing the
End Time button.
b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY AFTER A SET COOK PERIOD
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day. Step 2 Place food onto the correct shelf position in the oven and close the oven door(s). Step 3 Turn the oven control(s) to the required temperature, and if necessary select the appropriate oven
function.
Step 4 Press & hold in the Cook Period button, the display will read 0.00 and the 'cookpot'
.
130
symbol will light up. With the Cook Period button still held in set the required Cook Period using the "+" and "-" buttons. Example: 1hr 30 min
Step 5 Release all buttons.
utes (as shown).
A U T
.
4120
O
NOTE: The Cookpot symbol disappears
A U T
.
6120
O
.
6120
The timer display will revert to the time of day with the 'Auto' symbol lit & 'cookpot' symbol remaining lit.
At the end of the Cook Period the 'Auto' symbol will flash and will be heard. The audible tone will continue until cancelled. The 'Auto' symbol will continue to flash until the timer is returned to Manual operation (see below).
Step 6 Press the Manual returned to Manual.
Step 7 Turn the oven control(s) to the OFF position.
button. The audible tone will be cancelled and the oven(s) will be
an intermittent audible tone
10
OVEN TIMER OPERATION
TO CANCEL AN AUTO COOKING PROGRAMME BEFORE THE COOK PERIOD HAS FINISHED.
Step 1 Turn the oven control to the OFF position.
.
5100
Step 2 Press the Manual button to return the oven to "Manual" operation. The 'Auto' sym- bol will go out.
Note 1 When cooking automatically the Cook Period can be checked at any time by simply pressing
the Cook Period button.
OTHER NOTES ON TIMER OPERATION
1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the Cook Period
button.
2. When cooking Automatically the End Time can be checked at any time by simply pressing the End Time button.
3. Having set a Cook Period and End Time an electronic device stores the
will switch the oven(s) on and off at the required times.
4. When setting an Auto Cooking Programme and a mistake is made, to clear:­(a) Press & release the Manual button. (b) Start the sequence again.
5. If at any time the display shows three flashing zero's oven has been interrupted. Reset the timer to the correct time of day. Food in the oven may, therefore, not
have been cooked, before serving check food is thoroughly heated and completely cooked.
6. To set each function always press and hold the required function button and at the same time press "+" or "-" buttons.
0.00 and 'Auto', it is likely that the electricity supply to the
information. The device within the timer
11
Loading...
+ 25 hidden pages