Instruction ManualInstruction Manual
CDCF 6/CDCF 6S
DishwasherDishwasher
Read this Manual
This manual contains sections of Safety
Instructions,Operating Instructions,
Installation Instructions and Troubleshooting
Tips etc. Carefully reading it before using the
dishwasher will help you to use and maintain
the dishwasher properly.
Before Calling for Service
Safety Information
Operating Instructions
Installation instruction
Troubleshooting Tips
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
WARNING!
When using your dishwasher, follow the below basic precautions including the following:
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event
n
of a malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a
path of least resistance of electric current. This
appliance is equipped with a cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate
outlet that is installed and grounded in accordance
with all local codes and ordinances.
WARNING! PROPER USE
n
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
n
Do not touch the heating element during or
immediately after use.
n
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic
it ems not so marked, check the manufactures
recommendations.
n
Use only detergent and rinse additives designed
for an automatic dishwasher. Never use soap ,
laundry detergent, or hand washing detergent
in your dishwasher. Keep these products out of
children.
n
Keep child away from detergent and rinse aid, keep
child away from the open door of the dishwasher,
there could still be some detergent left inside.
n
n
n
n
WARNING!
Improper connection of the equipment-
n
grounding conductor can result in a risk
of electric shock. Check with a qualified
electrician or service representative if you
are in doubt whether the appliance is
properly grounded. Do not modify the plug
p rovided w ith t hea ppliance ; If i t is not fit
for the outlet .have a proper outlet installed
by a qualified electrician.
n
Do not operate your dishwasher unless all
enclosure panels are properly inplace. Open the
door very carefully if the dishwasher is operating,
there is a risk of water squirting out.
n
Do not place any heavy objects of stand on the door
when it is open. The appliance could tip forward.
n
When loading items to be washed:
1) Locate sharp items so that they are not likely to
damage the door seal;
2) Load sharp knives with the handles up to reduce
the risk of cut-type injuries.
n
When using your dishwasher, you should prevent
plastic item from contacting with heating element.
n
n
n
n
n
n
n
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY
SAVE THESE INSTRUCTIONS
1
Control Panel
IMPORTANT!
10
1
2
3
4
7
8
5
6
7
8
9
10
2
1
1
2
3
4
3
4
5
6
5
6
9
2
8
7
10
9
10
Intensive
For the heaviest soiled loads,
such as pot s , p a ns, cas s erole
dishes and dishes that have
been sitting with dried f o od
on the m f or a while.
Pre-wash（50℃）
Wash(70 ℃)
Rinse
Rinse
Rinse (70 ℃)
Drying
3/15 gr.
Normal
Econo my
(*EN 50242)
Glass
Rapid
3in1
For nor mall y so iled loads,
su c h a s , pl a tes , gla sse s
and lig h t ly soi led pans.
standard daily c ycle.
For lightly soiled loads,such
as plates,glas ses,bow ls and
lightly soiled pans.
For lightly soiled loads,
such as glasses , cry st al and
fine c hi na.
Ashorterwashforlightly
soiled loads (max 4 plate setti ngs).
pots
For normallysoiledloads,
uch as pla tes , gla sses, and
lightly soiled pans . Standard
daily cycle.
Pre-wash
Wash (60 ℃)
Rinse
Rinse (70 ℃)
Drying
Pre-wash
Wash(55 ℃)
Rinse
Rinse (70 ℃)
Drying
Wash (45 ℃)
Rinse
Rinse (60 ℃)
Drying
Wash (40 ℃)
Rinse
Rinse
Drying
Pre-wash
Wash (60 ℃)
Rinse
Rinse (70 ℃)
Drying
3/15 gr.
3/15 gr.
15 gr.
15 gr.
3in1(1pcs)
Turning on the Appliance
Draw out the lower and upper basket, load the dishes and push them
1
back. It is commended that loading the lower basket first, then the
upper one. The expensive and finer chinaware should not be put in.
With a little force to ensure the door is properly closed.
2
Note: a sound of click could be heard when the door is closed
perfectly.
3
Insert the plug into the socket.
The power supply is 230V 50HZ, the specification of the socket is
250V 10A.
Press the ON/OFF button
4
According to the soil level to choose the desired program by
5
pressing program selection button.
6
Press this button to start automatic washing.
Press the ON/OFF button at the end of washing. Open the door of
7
dishwasher after waiting 30 minutes.
Press the Start/ button
to stop washing.
At end of washing, the time display will flash for 8
seconds while the buzzer sound. But at the end of
delayed washing, no sound of the buzzer, only
the flash of the time display.
3
If your model have not water softener, you may skip this section.
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliances is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the
water.
Remove the lower basket and then unscrew and remove the cap from the salt
1
container.
2
If you are filling the container for the first time ,fill water .
3
Place the end of the funnel(supplied) into the hole and introduce about of
salt .It is normal for a small amount of water to come out of the salt container
1kg
4
Carefully screw the cap back on.
4
DETERGENT DISPENSER
YOU MAY NOT ADD TOO MUCH DETERGENT TO PREVENT THE FORMATION OF DEPOSITS BECAUSE YOUR DISHWASHERS
HAVE SPECIALLY-DESIGNED WATER SOFTENERS.
The dispenser must be refilled before the start of each wash cycle following the instructions provided in the" Wash Cycle
Table".Your dishwashers use less detergent and rinse aid than conventional dishwashers. Generally, only one tablespoon
of detergent is needed for a normal wash load. Also, more heavily soiled items need more detergent. Always add the
detergent just before starting dishwasher, otherwise it could get damp and will not dissolve properly.
WARNING!
Proper Use of Detergent
In accorance with En50242 standard, the dispenser should be set on the maximum lever
when doing the performance.
5
Loading the Dishwasher Racks.
For best performance of the dishwasher, follow these loading guidelines. Features and appearance of racks and
silverware baskets may vary from your model.
It is preferable to place serving dishes and lids on the side of the racks in order to avoid blocking the rotation of the
top spray arm.
Pots, serving bowls, etc, must always be placed top down.
Deep pots should be slanted to allow water to flow out.
The rack feature fold down tine rows so that larger or more pots and pans can be loaded.
66
IN
33
11
11
33
55
99
1010
88
44
33
3
3
77
22
6
SILVERWARE BASKET
Silverware should be placed in the silverware basket with handles at the bottom: If the rack has side baskets, the spoon should
be loaded individually into the appropriate slots, Especially long utensils should be placed in the horizontal position at the
front of the upper rack.
3
5
4
4
4
7
3
3
1
2
3
5
6
7
IN
5 1 2
5
1
2
5
1
2
3
4
2
51
4
8
5
1
4
3
4
3
Turning on the Appliance
Make sure that the plug of the appliance is inserted into the wall socket.
1
2
3
4
5
6
Press the Start/Reset key, the washing will start after few seconds.
Make sure that the water supply is turned on to full pressure.
Load the dishwasher(see the section entitled, " Loading the Dishwasher ").
Pour in the detergent(seethe section entitled, " Salt, Detergent and RinseAid " ).
Press the "prog key-press" to select the "wash cycle".(see the section entitled."wash cycle table"
Press the key to set the delay start time. This dishwasher can be delay among 3,6,9 and 12 hours.
If you want to cancel the delay start, just change delay time up to no hours selected.
2
2
1
6
WARNING!
Do not leave any item extend through bottom.
Knives and other utensils with sharp points
must be loaded in the basket with their points
down or placed in an horizontal position.
)
.
8
Cancelling or modifying a wash setting. . .
When the washing cycle has finished, an 8 second buzzer will sound.Turn off the appliance using the ON/OFF button,open the door
of the dishwasher. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are
still hot and more susceptible to breakage. They will also dry better.
Forget to Add a Dish?
A forgotten dish can be added any time before the detergent cup opens.
Open the door a little to stop the washing.
1
After the spray arms stop working,you can open the door
2
completely.
3
Add forgotten dishes.
Close the door, the dishwasher will resume after ten seconds.
4
WARNING!
It is dangerous to open the door when washing, as the water may scald you.
7
The filter prevent larger remnants of food or other objects from getting inside the pump. This residue can
occasionally clog up the filters.
A flat (Main filter) and a microfilter(fine filter).
Main filter
Food and soil particles trapped by this filter are pulverized by a
2
3
1
special jet on the lower spray arm and washed down the
drain.
Coarse filter
Larger items, such as pieces of bone or glass, that could clog
the drain are trapped in the coarse filter. To remove an item
caught in this filter, gently squeeze the taps on the top of this
filter and lift it out.
Fine filter
This filter holds soil and food residue in the sump area and
prevents it from being redeposit on the dishes during a cycle.
1
2
3
Caring for the Dishwasher
To clean the control panel use a lightly dampened cloth then dry thoroughly. To clean the dishwasher outside, do
not use solvents (degreasing action) neither abrasives, but only a cloth soaked with water.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Protect Against Freezing
If your dishwasher is left in an unheated place during the winter, ask a service technician to:
1
Cut off electrical power to the dishwasher. Remove
fuses or trip circuit breaker.
Reconnect the water inlet pipe to the
4
water valve.
2
Turn off the water supply and disconnect the water
inlet pipe from the water valve.
Drain water from the inlet pipe and water valve.
3
(Use a pan to catch the water.)
Remove the plastic sump cover in the
5
tub the bottom and use a sponge to
soak up water in rubber boot.
WARNING!
8
WARNING!
9
About Electricity Connecting
.
CAUTION, for personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD GROUNDING PRONG FROM THE POWER CORD.
Electrical Requirements
This dishwasher is designed for operation on an adequately wired individual 220~240VAC,50~60HZ. Use required fuse 10 amp.
Fused electrical supply is required-copper wire only. Time delay fuse or circuit breaker recommended and provide separate
circuit serving only this appliance. Outlet should be placed in adjacent cabinet.Make sure that plug on the appliance remains
eccessible after installation.
Insure proper ground
exists before use
How to Connect the safety supply hose
The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.
Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below the minimum
consult our Service Department for advice.
Pull The supply hoses completely out from storage compartment located at rear of dishwasher.
1
Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.
2
Turn water fully on before starting the dishwasher.
3
WARNING!
How to Disconnect the safety supply hose
Turn off the water.
1
Release the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
2
room, from severe splashing.
Unscrew The safety supply hose from the faucet..
3
How to Disconnect the Dishwasher
Remove the power cord plug from the wall receptacle.
1
Disconnect Unicouple from faucet adapter.
2
NOTE: When motor stops at the end of the final rinse, the Unicouple can be disconnected and returned to storage.
10
COLD WATER CONNECTION
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the
water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and
damage the appliance.
HOT WATER CONNECTION
The water supply to the appliance can also be connected to the house hot water line (centralized system, heating system),
as long as it does not exceed a temperature of 60 C. In this case, the wash cycle time will be shortened by about 15 minutes
and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as those for the connection to the
cold water line.
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent
cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to
facilitate proper installation.
How to Drain Excess Water
From Unicouple Hoses
If the sink is 34 or higher from the floor, the excesswater in Unicouple hoses
cannot be drained directly into the sink. It will be necessary to drain excess
water from hoses into a bowl or suitable container that is heldoutside and lower
than the sink.
11
Before Calling for service . . .
Troubleshooting Tips
Review the charts on the following pages may make you be free of calling for service.
Problem Possible Causes What To Do
Dishwasher doesn t
run
Drain pump doesn t
stop
Fuse blown, or the
circuit breaker acted
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Noise
Suds in the tub
Stained tub interior
Dishes are not dried
Some audible sounds are
normal
Utensils are not secure
in the baskets or something
small has dropped into
the basket
Motor hums Dishwasher has not been used regularly. If you do not use it
Improper detergent
Spilled rinse agent Always wipe up rinse agent
Detergent with
colorant was used
Rinse agent dispenser
is empty
Sound from soft food shredding action and detergent cup
opening.
To ensure everything is secured in the dishwasher.
often, remember to set it to fill and pump out every week,
which will help keep the seal moist.
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
Add 4 litres of cold water to the tub. Close and latch the
dishwasher, then drain out the water by slowly turning the
Dial until a drain period is reached. Repeat if necessary.
spills immediately.
Make sure that the detergent is the one without colorant.
Make sure that the rinse agent dispense is filled.
Dishes and flatware
not clean
Spots and filming
on glasses and
flatware
Improper program
Improper rack loading Make sure that the action of the detergent dispenser and
Extremely hard water
1
Low inlet
2
temperature
Overloading the
3
dishwasher
Improper loading
4
Old or damp powder
5
detergent
Empty rinse agent
6
dispenser
Incorrect dosage of
7
detergent
12
Select stronger program
spray arms are not blocked by large dishware.
To remove spots from glassware:
1
Take out all metal utensils out of the dishwasher.
Do not add detergent.
2
Choose the longest cycle.
3
Start the dishwasher and allow it to run for about
4
18 to 22 minutes, then it will be in the main wash.
Open the door to pour 2 cups of white vinegar
5
into the bottom of the dishwasher.
Close the door and let the dishwasher complete
6
the cycle. If the vinegar does not work: Repeat
as above, except use 1/4 cup (60 ml)of citric acid
crystals instead of vinegar.
Before calling for service . . .
Problem Possible Causes What To Do
Cloudiness on
glassware
Yellowo rb rown f ilm
on inside surfaces
White film on inside
surface
Detergent cup lid
won t latch
Detergent left in
dispenser cups
Steam
Black or gray
marks on dishes
Combination of soft
water and too much
detergent
Tea or coffee stains using a solution of 1/2 cup of bleach and 3 cups warm water
Iron deposits in water
can cause an overall film
Hard water minerals To clean the interior, use a damp sponge with dishwasher
Dial is not in the OFF
position
Dishes block detergent
cups
Normal phenomenon
Aluminum utensils have
rubbed against dishes
Use less detergent if you have soft water and select a
shortest cycle to wash the glassware and to get them clean.
to remove the stains by hand.
WARNING
You have to wait for 20 minutes after a cycle to let the heating
elements cool down before cleaning interior; otherwise, burns
will happen.
You have to call a water softener company for a special filter.
detergent and wear rubber gloves. Never use any other cleaner
than dishwasher detergent for the risk of foaming or suds.
Turn the Dial to OFF position and slide the door latch to the
left.
Re-loading the dishes properly.
There is some steam coming through the vent by the door
latch during drying and water draining.
Use a mild abrasive cleaner to eliminate those marks.
Water standing in
the bottom of the tub
Dishwasher leaks
This is normal A small amount of clean water around the outlet on
the tub bottom at the back of the tub keeps the water
seal lubricated.
Overfill dispenser or rinse
aid spills
13
Loading...