Camp Chef PELLET GRILL Instructions Manual

WARNING

• To installer or person assembling this appliance: Leave this manual
with this appliance for future reference.

• To consumer: Keep this manual for future reference.

This instruction manual contains important information necessary
for the proper assembly and safe use of this product.

Read and follow all warnings and instructions before assembling and
using the appliance.

Follow all warnings and instructions when using the appliance.

DO NOT DISCARD THIS INSTRUCTION MANUAL.

Fill in model number found on the product.

Model Number:

For outdoor use only.

DANGER

1. Never operate this
appliance unattended.

2. Never operate this
appliance within 10 ft
(3 m) of any structure,
combustible material or
other gas cylinder.

3. Never operate this
appliance within 25 ft
(7.5 m) of any flammable
liquid.

4. If a fire should occur, keep
away from appliance and
immediately call your
fire department. Do not
attempt to extinguish an
oil or grease fire with
water.

Failure to follow these
instructions could result
in fire, explosion or burn
hazard, which could cause
property damage, personal
injury or death.

PELLET GRILL INSTRUCTIONS

WWW.CAMPCHEF.COM

PATENT PENDING

© 2013 Camp Chef

1. Do NOT leave this appliance unattended while in use. The user must remain in the immediate area of the product and

have a clear view of the product at all times during operation.

2. Keep children and pets away from burner at all times.

3. The use of alcohol, prescription or non-prescription drugs may impair your ability to properly assemble or safely

operate this appliance.

4. For OUTDOOR use only. Do NOT use in a building, garage or any other enclosed area. Do NOT use in or on recreational

vehicles or boats. NEVER use this appliance as a heater.

5. Do not operate appliance under ANY overhead construction. Keep a minimum clearance of 10 feet (3 m) from the sides,

front and back of appliance to ANY construction. Keep the area clear of all combustible material and flammable liquids,

including wood, dry plants and grass, brush, paper, and canvas.

6. This product is not intended for commercial use.

7. Always allow the appliance to cool before covering with the patio cover.

8. Always cover the appliance, with patio cover (if supplied), when not in use.

9. Always unplug grill before installing patio cover.

10. Use only on level surface.

11. Make sure burner clean-out is closed before starting the grill.

12. Make sure the grease bucket is in place before starting the grill.

13. In the event of a fire the dial should be turned to shutdown, close the lid, and leave it closed until the fire goes out.

After allowing the grill to cool, follow the cleaning instructions before the next use.

14. Use only food grade hardwood pellets manufactured for use in pellet grills. Using softwood or heating pellets will

void your warranty.

15. Do not allow the hopper to run out of pellets. Pellets can be added at any time. The hopper will hold approximately 15

pounds of pellets. The pellet usage will vary greatly depending on the ambient temperature as well as

cooking temperature.

16. It is recommended that you not store pellets in the hopper for extended periods as they may absorb moisture from

the air and clog the auger.

17. Keep the lid closed during cooking. The grill is designed to cook with the lid closed.

18. Note that the cooking temperature displayed on the digital readout is measured near the cooking surface on the left

side of the grill. The actual temperature inside the cooking chamber will vary slightly throughout.

DANGER

Do not work on this grill if it is plugged in. Electric shock may occur resulting in death or serious injury.

PG24-1 (1)

WARMING RACK

PG24-2 (1)

COOKING GRATE

PG24-3 (1)

DRIP TRAY

PG24-4 (1)

HEAT DEFLECTOR

M6 X 76 BOLT (1)

PG24-5 (1)

CHIMNEY CAP ASM

PG24-6 (1)

CHIMNEY

PG24-7 (1)

CHIMNEY GASKET

M6 NUT (2)

M6 X 15 BOLT (2)

M6 NUT (2)

M6 LOCK WASHER (2)

M6 FLAT WASHER (2)

PG24-8 (1)

SHELF

M6 X 15 BOLT (7)

PG24-10 (1)

BURNER PULLOUT

PG24-9 (1)

PULLOUT KNOB

PG24-11 (1)

GREASE BUCKET

PG24-12 (2)

RIGHT LEG

M8 X 55 BOLT (8)

M8 NUT (8)

M8 LOCK WASHER (8)

M8 FLAT WASHER (8)

PG24-13 (2)

LEFT LEG

PG24-14 (2)

LEG PLUG

PG24-17 (1)

ASH CUP

PG24-16 (2)

WHEEL

PG24-15 (2)

WHEEL AXLE

M10 FLAT WASHER (2)

M10 ACORN NUT (2)

PG24-18 (1)

HANDLE

M6 X 15 BOLT (2)

PG24-19 (1)

THERMOCOUPLE

PG24-20 (1)

BURNER

PG24-21 (1)

HEATING ROD

PG24-22 (1)

AUGER

PG24-23 (1)

AUGER BUSHING

PG24-24 (1)

AUGER MOTOR

PG24-25 (1)

AUGER PIN W/NUT

PG24-26 (1)

BLOWER MOTOR

PG24-27 (1)

BLOWER IMPELLER

PG24-28 (1)

MEAT PROBE

M4.2 X 10 SCREW (4)

PG24-29 (1)

CONTROLLER

PG24-30 (1)

CONTROLLER KNOB

M4.2 X 10 SCREW (2)

PG24-31 (1)

HOPPER ASM

PG24-32 (1)

LID

PG24-33 (1)

LID ROD

PG24-34 (1)

FEED GASKET

M4.2 X 10 SCREW (4)

PG24-35 (1)

AUGER FAN BOX ASM

INSTALL HANDLE

1. Install the handle as shown in Fig 3.

2. Tighten all hardware.

INSTALL SHELF

1. Install shelf as shown in Fig 4.

2. Tighten all hardware.

GREASE BUCKET

1. Hang grease bucket from tube as shown in Fig 4.

ASH CUP

1. Install Ash Cup as shown in Fig 5. Never use grill without Ash Cup in place.

M6 X 15 SCREW

M6 X 15 SCREW

GREASE BUCKET

ASH CUP

M6 X 15 SCREW

M6 NUT

M6 FLAT WASHER

M6 LOCK WASHER

CHIMNEY GASKET

M6 NUT

M6 X 76 BOLT

M8 X 45 BOLT

M8 FLAT WASHER

M8 LOCK WASHER

M8 NUT

ASSEMBLY INSTRUCTIONS

ATTACH THE LEGS

1. Lay the grill on its back.

2. Install each of the 4 legs as shown in Fig 1. Make sure the legs with wheels are attached to the right side of the grill
with the wheels facing out.

3. Stand the grill upright

4. Tighten all hardware.

ATTACH CHIMNEY AND CHIMNEY CAP

1. Install chimney to grill as shown in Fig 2. Make sure to install the gasket between the grill and the chimney.

2. Tighten all hardware.

3. Install M6 x 76 Bolt through chimney cap and secure using Qty (1) M6 nut. Thread second nut onto bolt leaving
approximately 1.5” to the top of the cap. Thread cap assembly down into the chimney bracket until the lower nut hits
the bracket. See Fig 2.

4. The height of the chimney cap can be adjusted for summer and winter. In the summer the gap should be approximately
1-1/2”. In the summer the gap should be approximately ½”.

5. Tighten all hardware.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5