Campbell Hausfeld IN733400AV, CHN10510 User Manual

4.98 Mb

See Warranty on page 8 for important information about commercial use of this product.

Operating Instructions




Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

1 inch 23g

Micro Pin Nailer

Table of Contents


Description . . . . . . . . . . . . . . . . . . . . .


Unpacking . . . . . . . . . . . . . . . . . . . . . .


Safety Guidelines . . . . . . . . . . . . . . . .


Important Safety Information . . . . . .


Tool Components and


Specifications . . . . . . . . . . . . . . . . . . . .


Operating Instructions . . . . . . . . . . . .


Lubrication . . . . . . . . . . . . . . . . . . . .


Recommended Hookup . . . . . . . . . .


Operational Mode . . . . . . . . . . . . . .


Trigger Only Mode . . . . . . . . . . . . . .


Loading/Unloading The Tool . . . . . .


Adjusting Direction of Exhaust . . . .


Clearing A Jam From The Tool . . . .


User-Maintenance Instructions . . . . .


Interchange Information . . . . . . . . . .


Troubleshooting Chart .. .. .. .. .. .. .. .. .. .. .. ..


Warranty . . . . . . . . . . . . . . . . . . . . . . .



This pin nailer is designed for tacking decorative trim, glazing strips, small picture frames and cabinetry trim.. Features include: adjustable exhaust, narrow nose for fitting in tight spaces, rubber comfort grip, and trigger lock..


After unpacking the unit, inspect carefully for any damage that may have occurred during transit.. Make sure to tighten fittings, bolts, etc.., before putting unit into service..

Safety Guidelines

This manual contains information that is very important to know and understand.. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS.. To help

recognize this information, observe the following symbols..

Danger indicates an imminently

hazardous situation which, if not avoided, WILL result in death or serious injury.

Warning indicates a potentially

hazardous situation which, if not avoided, COULD result in death or serious injury.

Caution indicates a potentially

hazardous situation which, if not avoided, MAY result in minor or moderate injury.

Notice indicates important

information, that if not followed, may cause damage to equipment.

NOTE: Information that requires special attention..

Important Safety Instructions


This manual contains safety, operational and maintenance information.. Contact your Campbell Hausfeld representative if you have any questions..

When using tools, basic precautions should always be followed, including

the following:

Model CHN10510

Locate model and date code on tool and record below:

Model No..: _____________________

Date Code: _____________________

Retain these numbers for future reference..

California proposition 65

This product or

its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

You can create dust when you cut, sand, drill or grind

materials such as wood,

paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

Campbell Hausfeld Tools meet or exceed Industries’ Standards as set forth by the American National Standard

IN733400AV 3/10

Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002..


© 2010 Campbell Hausfeld / Scott Fetzer

For parts, product & service information



Important Safety Instructions


able to create sparks resulting in the


better control of the tool in



ignition of the dust or fumes..


unexpected situations..



Keep bystanders, children, and


Use safety equipment. A dust mask,







visitors away while operating the


non-skid safety shoes and a hard


To reduce the risks of




tool. Distractions are able to result in


hat must be used for the applicable



electric shock, fire, and






the loss of control of the tool..






injury to persons, read all





















the instructions before


Personal Safety


Always wear eye






using the tool.


Stay alert. Watch what you are




Be thoroughly familiar with the

g.. Always wear hearing



doing and use common sense








controls and the proper use of the



protection when using




when operating the tool. Do not




equipment.. Follow all instructions..



the tool. Prolonged




use the tool while tired or under




Contact your Campbell Hausfeld



exposure to high intensity





the influence of drugs, alcohol,




representative if you have any


or medication. A moment of


noise is able to cause






hearing loss..




inattention while operating the















Only persons well acquainted with


tool increases the risk of injury to

h.. Do not attach the hose or tool to



these rules of safe operation should




your body. Attach the hose to the



be allowed to use the unit..


Dress properly. Do not wear loose


structure to reduce the risk of loss of




Read and


balance if the hose shifts..





clothing or jewelry. Contain long





understand tool












hair. Keep hair, clothing, and


Always assume that the tool





labels and manual. Failure to follow



gloves away from moving parts.


contains fasteners. Do not point

warnings, dangers, and cautions could




Loose clothes, jewelry, or long


the tool toward yourself or anyone




Work Area


hair increases the risk of injury to


whether it contains fasteners or not..


persons as a result of being caught











Keep the work area clean and well






in moving parts..









not nail on








lighted. Cluttered benches and dark


Avoid unintentional starting.


top of another nail. This is able to



areas increase the risks of electric


cause the nail to be deflected and




Be sure the switch is off before




shock, fire, and injury to persons..



hit someone, or cause the tool to




connecting to the air supply. Do not






react and result in a risk of injury to

b.. Do not operate the tool






carry the tool with your finger on





in explosive atmospheres,


the switch or connect the tool to the





Remove finger









such as in the presence


air supply with the switch on..











from the trigger










of flammable liquids,



Do not overreach. Keep proper


when not driving fasteners. Never







gases, or dust. The tool is


carry the tool with finger on trigger,




footing and balance at all times.


Operating Instructions









Proper footing and balance enables

the tool is able to fire a fastener.


Tool Components and Specifications

Requires: 0..15 SCFM with 10 fasteners per minute @ 90 psi

Adjustable Exhaust

Trigger Lock

Air inlet: 1/4 inch NPT

PIN SIZE RANGE: 3/8 inch to 1 inch


110 headless pins, 23 g

WEIGHT: 2 lbs.. 3 oz..

LENGTH: 8-1/4 inches

HEIGHT: 6-1/4 inches


PRESSURE RANGE: 60 psi – 100 psi





Pin Discharge


Adjustment Switch

Nail Loading Area



Important Safety Instructions (Continued)

Always remain in a firmly balanced

position when using or handling the tool.

Avoid long extended periods of work

with the tool. Stop using the tool if you feel pain in hands or arms.

Tool Use and Care

a..Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against the body is unstable and is able to lead to loss of control..

b..Do not force the tool. Use the correct tool for the application.. The correct tool will do the job better and safer at the rate for which the tool is designed..

c..Do not use the tool if the switch does not turn the tool on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired..

h..Use only those fasteners listed in the Accessories section of this manual. Fasteners not identified for use with this tool by the tool manufacturer are able to result in a risk of injury to persons or tool damage when used in this tool..

i.Selecting an appropriate tool actuation system, taking into consideration the work application for which the tool is used..

Never use

gasoline or other flammable liquids to clean the tool. Never use

the tool in the presence of flammable liquids or gases. Vapors could ignite by a spark and cause an

explosion which will result in death or serious personal injury.

Do not remove, tamper with, or otherwise cause the trigger lock or trigger

to become inoperable. Do

not operate any tool which has been modified in a like fashion. Death or serious personal injury could result.

air to remain in the tool. Death or serious personal injury could occur.

Never place hands or any other body parts in the fastener discharge area of the

tool. The tool might eject a fastener and could result in death or serious personal injury.

Never carry the tool by the air hose or pull the hose to move the tool or

a compressor. Keep hoses away from heat, oil and sharp edges. Replace any hose that is damaged, weak or worn. Personal injury or tool damage could occur.

Always assume the tool contains

fasteners. Respect the tool as a working implement; no horseplay. Always keep others at a safe distance from the work area in case of accidental discharge of fasteners. Do not point the tool toward yourself or anyone whether it contains fasteners or not. Accidental triggering of the tool could result in death or serious personal injury.


Disconnect the


Do not drive a fastener


tool from the air

Do not touch the trigger

on top of other


source before making adjustments,

fasteners. The fastener


unless driving fasteners.


doing tool maintenance, clearing

could glance and cause


Never attach air line to


jams, leaving work area,loading,

death or a serious puncture wound.


tool or carry tool while


or unloading the tool. Such



touching the trigger. The tool could


precautionary measures reduce the


eject a fastener which will result in



risk of injury to persons..

Do not operate or allow


death or serious personal injury. Also


Store the tool when it is idle out

anyone else to operate

actuate the trigger guard to the safe

the tool if any warnings


of reach of children and other

position when not in use.


or warning labels are not legible.


untrained persons. A tool is




Warnings or warning labels are located


dangerous in the hands of untrained


on the tool magazine and body.



Always disconnect the

Do not drop or


Maintain the tool with care. Keep

tool from the power

throw the tool.

source when unattended,

Dropping or throwing the tool can


a cutting tool sharp and clean.. A


performing any maintenance or repair,

result in damage that will make the tool


properly maintained tool, with sharp

clearing a jam, or moving the tool to a

unusable or unsafe. If the tool has been


cutting edges reduces the risk of

new location. Do not load the tool with

dropped or thrown, examine the tool


fasteners when the trigger is depressed.

closely for bent, cracked or broken parts


binding and is easier to control..


The tool could eject a fastener causing

and air leaks. STOP and repair before


Check for misalignment or binding

death or serious personal injury.

using or serious injury could occur.




of moving parts, breakage of parts,


Avoid using the


and any other condition that affects


tool when the


Always fit tool with a

magazine is empty. Accelerated wear on


the tool’s operation. If damaged,


fitting or hose coupling

the tool may occur.


have the tool serviced before using..


on or near the tool in

Clean and check all


Many accidents are caused by poorly


such a manner that all


air supply hoses


maintained tools.. There is a risk of

compressed air in the tool is discharged


and fittings before connecting the


bursting if the tool is damaged..

at the time the fitting or hose coupling

tool to an air supply. Replace any


is disconnected. Do not use a check

valve or any other fitting which allows

damaged or worn hoses or fittings.

Tool performance or durability may be





Operating Instructions

Important Safety Instructions

b.. Never use oxygen, carbon dioxide,


Disconnect the air



combustible gases or any bottled



supply from the tool



gas as an air source for the tool.




to add lubricant..


Such gases are capable of explosion




a.. Tool service must be performed only




and serious injury to persons..




Turn the tool so the air


by qualified repair personnel.















inlet is facing up.. Place


b.. When servicing a tool, use only














4-5 drops of 30 W non-


identical replacement parts. Use








Do not use any type of





detergent oil into air inlet..







only authorized parts.






reactive gases, including, but




Do not use detergent


c.. Use only the lubricants supplied

not limited to, oxygen and










oils, oil additives, or airtool oils..

combustible gases, as a power source.


with the tool or specified by the



Air tool oils contain solvents which

Use filtered, lubricated, regulated








compressed air only. Use of a reactive


will damage the tool's internal



Do not make any

gas instead of compressed air may






modifications to

cause the tool to explode which will


3. After adding oil, run


the tool without first obtaining written

cause death or serious personal injury.



tool briefly.. Wipe off


approval from Campbell Hausfeld. Do








not use the tool if any shields or guards







any excess oil from the


are removed or altered. Do not use the

Use only a pressure-regulated




cap exhaust..


tool as a hammer. Personal injury or






compressed air source to limit 100 psi




tool damage may occur.

Recommended Hookup


Disconnect air

the air pressure supplied to




The illustration below shows the

the tool. The regulated pressure must


supply and release

not exceed 100 psi. If the regulator



recommended hookup for the tool..

tension from the pusher before



fails, the pressure delivered to the




The air compressor


attempting to clear jams because



60 psi

tool must not exceed 200 psi. The tool

fasteners can be ejected from the front


must be able to


could explode which will cause death or




of the tool. Personal injury may occur.

serious personal injury.





maintain a minimum

100 psi







Air Source







of 60 psi when the

Save These Instructions





a.. Never connect to an air source that


Do Not Discard




tool is being used.. An inadequate air





supply can cause a loss of power and

is capable of exceeding 200 psi.







Operating Instructions




inconsistent driving..


Over pressurizing the tool is able







2. An oiler can be


to result in bursting, abnormal










used to provide oil


operation, breakage of the tool or













This tool requires lubrication before



circulation through


serious injury to persons.. Use only




using the tool for the first time and




the tool.. A filter can


clean, dry, regulated compressed air





before each use.. If an inline oiler is




be used to remove


at the rated pressure or within the





used, manual lubrication through the



liquid and solid impurities which can

rated pressure range as marked on



air inlet is not required on a daily basis..


rust or “gum up” internal parts of

the tool.. Always verify prior to using








the tool..


the tool that the air source has been


The work surface




adjusted to the rated air pressure or


can become




Always use air supply hoses with

within the rated air-pressure range..

damaged by excessive lubrication.




a minimum working pressure

Proper lubrication is the owner’s








rating equal to or greater than the


responsibility. Failure to lubricate the




pressure from the power source if a


tool properly will dramatically shorten



the life of the tool and void your




regulator fails, or 150 psi, whichever










Recommended Hookup















Quick Plug













Quick Plug







Air Hose





Operating Instructions (Continued)

is greater.. Use 1/4 inch air hose for runs up to 50 feet.. Use 3/8 inch air hoses for 50 foot run or longer..

150 psi or greater

3/8 inch I..D..

4.Use a pressure regulator on the compressor, with an operating pressure of 0 psi - 125 psi.. A pressure regulator is required to control

the operating pressure of the tool between 60 psi and 100 psi..

Operational Mode

Always know the operational mode of

the tool before using. Failure to know the operational mode could result in death or serious personal injury.

Trigger Only Mode (with Trigger Lock)

The tool is a single-actuator device.. This mode requires that, with the trigger lock not positioned in the safe mode, only a pull of the trigger will fire a fastener..



After verifying there are no fasteners in the tool, safety check the operation of the activated trigger lock to prevent the tool from firing a fastener before storage.. Always disconnect from compressed air when not in use..


1.Set the pin length adjustment switch to the appropriate setting for the length of pins you are loading by first pushing in on the red switch and sliding until the notch is in the appropriate groove..

2. Push the latch button.. Pull back on the magazine cover fully..



3.Insert a stick of fasteners into the magazine with pins positioned as shown.. Make sure pins are not dirty or damaged.. Pins are marked for direction of loading..

4.Push the magazine cover forward until latch engages

5.Always unload all fasteners before removing tool from service.. Unloading is the reverse of loading, except always disconnect the air supply before unloading..

Adjusting The Direction Of The Exhaust

The tool is equipped with an adjustable direction

exhaust deflector.. Rotate This is intended to

allow the user to change the direction of the exhaust.. Simply twist the deflector to any direction desired..

Clearing A Jam From The Tool

1. Disconnect the air supply from the tool..

2.Remove all nails from the magazine (see "Loading/ Unloading The Nailer").. Failure to do so will cause the nails to eject from the front of the nailer..

3.Completely remove the two (2) small nose screws and the top nose plate to reveal the jammed fastener..

4.Using caution not to bend or damage the driver blade, use a pick or some other pointed object to pry free and clear the jammed fastener..

User-Maintenance Instructions

Technical Service

Please call our Tool Hotline at 1-800- 543-6400 with any questions regarding the operation or repair of this tool or for additional copies of this manual..

Fastener And Replacement Parts

Use only 23 gauge headless micropins

(or equivalent - see Fastener Interchange Information). Tool performance, safety and durability could be reduced if improper fasteners are used. When ordering replacement parts or fasteners, specify by part number.

Tool Repair

Only qualified personnel should repair the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently..


In order to properly drive the tiny micropins and leave a nearly

undetectable hole, the tips of the driver blades end in a fine point and are therefore quite vulnerable to abuse and extended use..


Operating Instructions


can be purchased by calling 1-800-

A small amount of oil must be used on

Instructions (Continued)

543-6400 and refer to part number

all moving surfaces and pivots.. After

To maximize the life of the blade,


reassembling, a few drops of 30W


non-detergent oil or equivalent, must

closely examine fasteners for defects..

Replace assembly by first removing the

be added through the air line before

Do not use defective or improper

four (4) head cap screws using the 4mm


fasteners.. Also load fasteners in the

hex wrench provided.. Remove head cap


proper orientation; the pin points and

and components to access the driver


the arrows always point toward the

piston.. Remove and replace driver

The tool should be stored in a cool dry

wood surface.. Drive fasteners into wood

assembly using your fingers.. Replace


products only (see "Loading/ Unloading

components and head cap as removed..


The Nailer")..

Assembly Procedure For Seals

Interchange Information

Even with good care, extended use

Can use 3/8 inch to 1 inch pins from the

When repairing a tool, the internal

of the tool may eventually lead to tip

following branded 23 g micropinners:

parts must be cleaned and lubricated..

failure.. Replacement driver assemblies

Senco FP10, Air Locker P630, Porter

Parker O-lube or equivalent must be


Cable PIN100, Grex P635, and Max


used on all o-rings.. Each o-ring must be




coated with O-lube before assembling..






Troubleshooting Chart



Stop using tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center.


Possible Cause(s)

Corrective Action

Air leaking at trigger valve

O-Rings in trigger valve housing are

Replace o-rings









Air leaking between housing

1. Damaged o-rings


Replace o-rings

and nose..


Damage to bumper


Replace bumper






Air leaking between housing

1. Loose screws


Tighten screws

and cap..


Damaged seal


Replace seal






Tool skips driving fastener

1. Worn bumper


Replace bumper



Dirt in nose piece


Clean drive channel



Dirt or damage prevent fasteners or


Clean magazine



pusher from moving freely in magazine





Damaged pusher spring


Replace spring



Inadequate air flow to tool


Check fitting, hose, or compressor



Worn o-rings on piston or lack of


Replace and lubricate o-rings








Damaged o-rings on trigger valve


Replace o-rings



Air leaks


Tighten screws and fittings



Cap seal leaking


Replace seal


10. Defect in automatic nail length plate

10. Clear problem with plate






Tool runs slow or has loss of


Tool not lubricated sufficiently


Lubricate nailer



Broken spring in cylinder cap


Replace spring




Exhaust port in cap is blocked


Replace damaged internal parts





Fasteners are jammed in tool

1. Guide on driver is worn


Replace guide



Fasteners are not correct size


Use only recommended fasteners



Fasteners are bent


Replace with undamaged fasteners



Magazine or nose screws are loose


Tighten screws



Driver is damaged


Replace driver





Operating Instructions

Limited Warranty

1.DURATION: From the date of purchase by the original purchaser as follows: One (1) Year..

2.WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400..

3..WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product..

4..WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: This Campbell Hausfeld nailer or stapler..

5..WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the duration of the warranty period with the exceptions below..


A.Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION.. If this product is used for commercial, industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase.. Some States do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you..

B.ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT.. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you..

C.Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied with product.. Accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions shall also include the removal or alteration of any safety devices.. If such safety devices are removed or altered, this warranty is void..

D.Normal adjustments which are explained in the owner’s manual(s) provided with the product..

E.Items or service that are normally required to maintain the product, e..g.. o-rings, springs, bumpers, debris shield, driver blades, gaskets, packings or seals, lubricants, or any other expendable part not specifically listed.. These items will only be covered for ninety (90) days from date of original purchase.. Underlined items are warranted for defects in material and workmanship only..

7.RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or components which are defective, have malfunctioned and/or failed to conform within the duration of the specific warranty period..


A.Provide dated proof of purchase and maintenance records..

B.Call Campbell Hausfeld (800) 543-6400 to obtain your warranty service options.. Freight costs must be borne by the purchaser..

C.Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s)..

9.WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts..

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights.. You may also have other rights which vary from state to state or country to country..


+ 16 hidden pages