Campbell Hausfeld IN715501AV, NB356502 User Manual

2.06 Mb
Loading...

See Warranty on page 8 for important information about commercial use of this product.

Operating Instructions

NB356502

 

 

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.

Angle Finish Nailer

Table of Contents

 

Description . . . . . . . . . . . . . . . . . . . . . .

1

Unpacking . . . . . . . . . . . . . . . . . . . . . . .

1

Safety Guidelines . . . . . . . . . . . . . . . . .

1

Important Safety Information . . . . . . .

1

Tool Components and

 

Specifications . . . . . . . . . . . . . . . . . . . . .

2

Operating Instructions . . . . . . . . . . . . .

4

Lubrication . . . . . . . . . . . . . . . . . . . . .

4

Recommended Hookup . . . . . . . . . . .

4

Operational Mode . . . . . . . . . . . . . . .

5

Single Cycle Mode . . . . . . . . . . . . . . .

5

Operating A Sequential Trip Tool . . .

5

Loading The Tool . . . . . . . . . . . . . . . .

5

Unloading The Tool . . . . . . . . . . . . . .

6

Adjusting the Nail Penetration . . . . .

6

Adjusting Direction of Exhaust . . . . .

6

Clearing A Jam From The Tool . . . . .

6

User-Maintenance Instructions . . . . . .

6

Fasteners Information . . . . . . . . . . . . .

7

Troubleshooting Chart .. .. .. .. .. .. .. .. .. .. .. .. ..

7

Warranty . . . . . . . . . . . . . . . . . . . . . . . .

8

Description

This nailer is designed for decorative trim, molding, window casings, furniture trim and picture frame assembly.. Features include: convenient rear loading magazine which holds up to 100 nails, no-mar tip, adjustable

exhaust, single cycle trigger, quick clear nose, and an adjustable depth of drive mechanism..

Unpacking

After unpacking the unit, inspect carefully for any damage that may have occurred during transit.. Make sure to tighten fittings, bolts, etc.., before putting unit into service..

Safety Guidelines

This manual contains information that is very important to know and understand.. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS.. To help

recognize this information, observe the following symbols..

Danger indicates an imminently

hazardous situation which, if not avoided, WILL result in death or serious injury.

Warning indicates a potentially

hazardous situation which, if not avoided, COULD result in death or serious injury.

Caution indicates a potentially

hazardous situation which, if not avoided, MAY result in minor or moderate injury.

Notice indicates important

information, that if not followed, may cause damage to equipment.

NOTE: Information that requires special attention..

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

Model NB356502

Locate model and date code on tool and record below:

Model No..: _____________________

Date Code: _____________________

Retain these numbers for future reference..

When using tools, basic precautions should always be followed, including

the following:

California proposition 65

This product or

its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

You can create dust when you cut, sand, drill or grind

materials such as wood,

paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

Campbell Hausfeld Tools meet or exceed Industries’ Standards as set forth by the American National Standard

IN715501AV 6/09

Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002..

 

© 2009 Campbell Hausfeld/Scott Fetzer

For parts, product & service information

 

visit www.chpower.com

Operating Instructions

Important Safety Instructions

 

able to create sparks resulting in the

 

better control of the tool in

(Continued)

 

ignition of the dust or fumes..

 

unexpected situations..

General

c..

Keep bystanders, children, and

e..

Use safety equipment. A dust mask,

a..

To reduce the risks of

 

 

visitors away while operating the

 

non-skid safety shoes and a hard

 

 

 

 

 

tool. Distractions are able to result in

 

hat must be used for the applicable

 

electric shock, fire, and

 

 

 

 

 

 

the loss of control of the tool..

 

conditions..

 

injury to persons, read all

 

 

 

 

 

 

 

 

 

 

 

 

 

the instructions before

 

Personal Safety

f..

Always wear eye

 

 

 

 

 

using the tool.

a..

Stay alert. Watch what you are

 

protection.

 

b.

Be thoroughly familiar with the

g.. Always wear hearing

 

 

doing and use common sense

 

 

controls and the proper use of the

 

 

protection when using

 

 

 

when operating the tool. Do not

 

 

 

equipment.. Follow all instructions..

 

 

the tool. Prolonged exposure to

 

 

use the tool while tired or under

 

 

Contact your Campbell Hausfeld

 

 

high intensity noise is able to cause

 

 

the influence of drugs, alcohol,

 

 

representative if you have any

 

 

hearing loss..

 

 

or medication. A moment of

 

 

questions..

 

 

 

 

 

 

 

 

inattention while operating the

h.. Do not attach the hose or tool to

 

 

 

 

 

c.

Only persons well acquainted with

 

tool increases the risk of injury to

 

your body. Attach the hose to the

 

these rules of safe operation should

 

persons..

 

structure to reduce the risk of loss of

 

be allowed to use the unit..

b..

Dress properly. Do not wear loose

 

balance if the hose shifts..

 

 

Read and

 

 

 

 

 

 

 

 

clothing or jewelry. Contain long

i..

Always assume that the tool

 

 

 

 

 

understand tool

 

hair. Keep hair, clothing, and

 

contains fasteners. Do not point

labels and manual. Failure to follow

 

 

 

gloves away from moving parts.

 

the tool toward yourself or anyone

warnings, dangers, and cautions could

 

 

 

Loose clothes, jewelry, or long

 

whether it contains fasteners or not..

result in DEATH or SERIOUS INJURY.

 

 

Work Area

 

hair increases the risk of injury to

j.

 

 

Do not nail on

 

 

 

 

persons as a result of being caught

 

 

 

 

 

 

top of another

a..

Keep the work area clean and well

 

 

 

 

 

in moving parts..

 

nail. This is able to cause the nail to

 

lighted. Cluttered benches and dark

c..

Avoid unintentional starting.

 

be deflected and hit someone, or

 

areas increase the risks of electric

 

cause the tool to react and result in a

 

 

Be sure the switch is off before

 

 

 

 

risk of injury to persons.

 

shock, fire, and injury to persons..

 

 

 

 

connecting to the air supply. Do not

k..

 

 

Remove finger

b.. Do not operate the tool

 

 

carry the tool with your finger on

 

 

 

 

 

 

 

from the trigger

 

 

 

 

 

in explosive atmospheres,

 

 

the switch or connect the tool to th

 

 

 

 

 

 

 

when not driving fasteners. Never

 

such as in the presence

 

 

air supply with the switch on..

 

carry the tool with finger on trigger,

 

of flammable liquids,

 

d..

Do not overreach. Keep proper

 

the tool is able to fire a fastener.

 

 

 

 

 

 

 

 

 

 

 

 

gases, or dust. The tool is

footing and balance at all times.

 

 

Proper footing and balance enables

Tool Components and Specifications

Requires: 1..0 Average SCFM with 10 fasteners per minute @ 90 psi

Air inlet: 1/4 inch NPT

NAIL SIZE RANGE: 1-1/2 inch to 2-1/2 inch

MAGAZINE CAPACITY:

100 Nails per load, 15 gauge

WEIGHT: 5 lbs.., 10 oz..

LENGTH: 14 inch

HEIGHT: 12-1/4 inch

MAXIMUM PRESSURE: 120 psi

PRESSURE RANGE: 70 psi – 120 psi

 

Adjustable Direction

Nail Loading

 

Exhaust Deflector

 

 

Area

Specification

Trigger

 

Decal

 

 

Adjustable

 

Warning Decal

Depth

 

Trilingual

Control

 

 

 

 

Aluminum Magazine

Quick

 

Hard Anodized

 

 

Clear

 

 

Latch

Nail Pusher Assembly

 

 

Rubber No-Mar Tip

 

 

Nail Discharge Area

 

www.chpower.com

2

NB356502

Important Safety Instructions (Continued)

Always remain in a firmly balanced

position when using or handling the tool.

Avoid long extended periods of work

with the tool. Stop using the tool if you feel pain in hands or arms.

Tool Use and Care

a..Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against the body is unstable and is able to lead to loss of control..

b..Do not force the tool. Use the correct tool for the application.. The correct tool will do the job better and safer at the rate for which the tool is designed..

c..Do not use the tool if the switch does not turn the tool on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired..

d..Disconnect the tool from the air source before making any

adjustments, changing accessories, loading, unloading or storing

the tool. Such preventive safety measures reduce the risk of starting the tool unintentionally..

e..Store the tool when it is idle out of reach of children and other untrained persons. A tool is

dangerous in the hands of untrained users..

f..Maintain the tool with care. Keep a cutting tool sharp and clean.. A

properly maintained tool, with sharp cutting edges reduces the risk of binding and is easier to control..

g..Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operation. If damaged, have the tool serviced before using.. Many accidents are caused by poorly maintained tools.. There is a risk of bursting if the tool is damaged..

h..Use only accessories that are identified by the manufacturer for the specific tool model. Use of an

accessory not intended for use with the specific tool model, increases the risk of injury to persons..

i.Selecting an appropriate tool actuation system, taking into consideration the work application for which the tool is used..

Never use

gasoline or other flammable liquids to clean the tool. Never use

the tool in the presence of flammable liquids or gases. Vapors could ignite by a spark and cause an

explosion which will result in death or serious personal injury.

Do not remove, tamper with, or otherwise

cause the Work Contact

Element (WCE) or trigger to become inoperable. Do not operate any tool which has been modified in a like fashion. Death or serious personal injury could result.

Do not touch the trigger unless driving fasteners.

Never attach air line to

tool or carry tool while touching the trigger. The tool could eject a fastener which will result in death or serious personal injury.

Always disconnect the tool from the power source when unattended,

performing any maintenance or repair, clearing a jam, loading, unloading or moving the tool to a new location. Always reconnect the air line AFTER loading any fasteners. Do not load the tool with fasteners when either the trigger is depressed or the Work Contact Element (WCE) is engaged. The tool could eject a fastener causing death or serious personal injury.

Always fit tool with a fitting or hose coupling on or near the tool in

such a manner that all compressed air in the tool is discharged at the time the fitting or hose coupling is disconnected. Do not use a check valve or any other fitting which allows air to remain in the tool. Death or serious personal injury could occur.

Never place hands or any other body parts in the fastener discharge area of

the tool. The tool might eject a fastener and could result in death or serious personal injury.

Never carry the tool by

the air hose or pull the hose to move the tool

or a compressor. Keep hoses away from heat, oil and sharp edges. Replace any hose that is damaged, weak or worn. Personal injury or tool damage could occur.

Always assume the tool contains

fasteners. Respect the tool as a working implement; no horseplay. Always keep others at a safe distance from the work area in case of accidental discharge of fasteners. Do not point the tool toward yourself or anyone whether it contains fasteners or not. Accidental triggering of the tool could result in death or serious personal injury.

Do not drive a fastener on top of other fasteners. The fastener

could glance and cause death or a serious puncture wound.

! WARNING

Do not operate or allow anyone else to operate the tool if any warnings

or warning labels are not legible. Warnings or warning labels are located on the tool magazine and body.

Do not drop or throw the tool.

Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe. If the tool has been dropped or thrown, examine the tool closely for bent, cracked or broken parts and air leaks. STOP and repair before using or serious injury could occur.

Always check that the Work Contact

Element (WCE) is operating properly. A fastener could accidentally be driven if the WCE is not working properly. Personal injury may occur (See "Checking the Work Contact Element" Section).

Avoid using the tool when the

magazine is empty. Accelerated wear on the tool may occur.

www.chpower.com

3

Operating Instructions

Important Safety Instructions

operation, breakage of the tool or

Operating Instructions

(Continued)

serious injury to persons.. Use only

 

Lubrication

 

Clean and check all

clean, dry, regulated compressed air

 

This tool requires lubrication before

air supply hoses

at the rated pressure or within the

and fittings before connecting the

rated pressure range as marked on

using the tool for the first time and

tool to an air supply. Replace any

the tool.. Always verify prior to using

before each use.. If an inline oiler is

damaged or worn hoses or fittings.

the tool that the air source has been

used, manual lubrication through the

Tool performance or durability may be

adjusted to the rated air pressure or

air inlet is not required on a daily basis..

reduced.

Service

within the rated air-pressure range..

The work surface

b.. Never use oxygen, carbon dioxide,

can become

 

a.. Tool service must be performed only

damaged by excessive lubrication.

combustible gases or any bottled

 

by qualified repair personnel.

 

Proper lubrication is the owner’s

gas as an air source for the tool.

 

 

responsibility. Failure to lubricate the

b.. When servicing a tool, use only

 

Such gases are capable of explosion

tool properly will dramatically shorten

identical replacement parts. Use

and serious injury to persons..

 

the life of the tool and void your

only authorized parts.

 

 

 

 

warranty.

 

 

 

 

 

 

 

c.. Use only the lubricants supplied

 

 

 

 

1. Disconnect the air

 

 

 

 

 

supply from the tool

 

with the tool or specified by the

Do not use any type of

O CO2

 

manufacturer.

reactive gases, including, but

 

to add lubricant..

 

not limited to, oxygen and

 

 

 

 

Do not make any

 

 

 

 

combustible gases, as a power source.

 

 

modifications to

2. Turn the tool so the air

 

Use filtered, lubricated, regulated

 

OIL

the tool without first obtaining written

 

inlet is facing up.. Place

compressed air only. Use of a reactive

 

approval from Campbell Hausfeld. Do

gas instead of compressed air may

 

4-5 drops of 30 W non-

 

not use the tool if any shields or guards

 

 

cause the tool to explode which will

 

detergent oil into air inlet..

 

are removed or altered. Do not use the

 

 

cause death or serious personal injury.

 

Do not use detergent

 

tool as a hammer. Personal injury or

 

 

 

 

 

 

tool damage may occur.

 

 

 

 

oils, oil additives, or airtool oils..

Disconnect air

Use only a pressure-regulated

 

Air tool oils contain solvents which

supply and release

 

will damage the tool's internal

compressed air source to limit 120 psi

tension from the pusher before

components..

 

the air pressure supplied to

 

 

 

attempting to clear jams because

 

 

 

 

the tool. The regulated pressure must

3. After adding oil, run

 

fasteners can be ejected from the front

 

of the tool. Personal injury may occur.

not exceed 120 psi. If the regulator

 

tool briefly.. Wipe off

 

 

fails, the pressure delivered to the

 

any excess oil from

 

Air Source

tool must not exceed 200 psi. The tool

 

the cap exhaust..

 

a.. Never connect to an air source that

could explode which will cause death or

 

 

 

serious personal injury.

 

 

Recommended Hookup

 

is capable of exceeding 200 psi.

 

 

 

 

 

 

 

 

Save These Instructions

 

 

 

Over pressurizing the tool is able

 

The illustration below shows the

 

Do Not Discard

 

to result in bursting, abnormal

 

 

recommended hookup for the tool..

 

 

 

 

Recommended Hookup

 

 

 

 

 

 

 

 

 

Quick

Regulator

 

 

Quick

Quick Plug

 

 

 

 

Coupler

 

 

 

Quick Plug

Coupler

(Optional)

(Optional)

 

 

Air Hose

Lubricator

Filter

www.chpower.com

4

70 psi Min.
120 psi Max.

NB356502

Operating Instructions (Continued)

1. The air compressor must be able to

maintain a minimum of 70 psi when the

tool is being used.. An inadequate air supply can cause a loss of power and inconsistent driving..

2. An oiler can be used to provide oil circulation through the tool.. A filter can

be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the tool..

3.Always use air supply hoses with a minimum working pressure

rating equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is greater.. Use 3/8 inch air hose for runs up to 50 feet.. Use 1/2 inch air hoses for 50 foot run or longer.. For better performance, install a 3/8 inch quick plug (1/4 inch NPT threads) with an inside diameter of ..315 inch (8mm) on the tool and a 3/8 inch quick coupler on the air hose..

150 psi or greater

3/8 inch I..D..

4.Use a pressure regulator on the compressor, with an operating pressure of 0 - 125 psi.. A pressure regulator is required to control the operating pressure of the tool between 70 and 120 psi..

Operational Mode

Always know the operational mode of

the tool before using. Failure to know the operational mode could result in death or serious personal injury.

This tool is sold with a black single sequential trigger. This tool is NOT intended to be used with a bump mode trigger.

Single Cycle Mode

 

 

This method is

 

 

recommended

 

 

for precise nail

1

2

placement.. This

 

 

mode requires the trigger to be pulled each time a nail is driven.. The nailer can be actuated by depressing the WCE against the work surface followed by pulling the trigger.. Or the nailer can be actuated by pulling the trigger and then depressing the WCE against the work surface..

The trigger must be released to reset the tool before another nail can be driven..

Operating A Sequential Trip Tool

Check the operation of the Work Contact

Element (WCE) trip mechanism before each use. The WCE must move freely without binding through its entire travel distance. The WCE spring must return the WCE to its fully extended position after being depressed. Do not operate the tool if the WCE trip mechanism is not operating properly. Personal injury may occur.

1.Disconnect the air supply from the tool..

2.Remove all fasteners

from the magazine (see Loading/ Unloading)..

3.Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding..

4.Reconnect air supply

to the tool..

Movement

5. Depress the Work

Contact Element (WCE) against the

work surface without

pulling the trigger.. The tool must not operate.. Do not use the tool if it operates without pulling the trigger.. Personal injury may result..

6. Remove the tool from

 

the work surface..

 

 

The Work Contact

 

 

Element (WCE) must

 

return to its original

 

 

down position.. The tool must not

operate.. Do not use the tool if it

operates while lifted from the work

surface.. Personal injury may result..

7. Pull the trigger

 

 

and depress the

 

 

work contact

1

2

element (WCE)

 

 

against the

 

 

work surface.. The tool MUST NOT

operate..

 

 

8.

Depress the

 

 

 

Work Contact

 

 

 

Element (WCE)

1

2

 

against the

 

 

 

 

work surface..

 

 

 

Pull the trigger.. The tool MUST

operate..

An improperly functioning tool

must not be used. Do not actuate the tool unless the tool is placed firmly against the work piece.

LOADINg the nailer

1.Always disconnect the tool from the air supply before loading fasteners..

2.Insert one stick of nails into rear loading slot while holding tool down so nails will slide forward in magazine..

Note: Make certain to insert nail heads

into wide area at top of magazines with nail points down..

3.

Press “Nail Bypass

Nail Pusher Mechanism

 

Button” in round hole

 

 

in the Nail Pusher

 

 

Mechanism and pull

Slot

 

back.. This allows the

Nail Bypass Button

 

 

 

nail clip to slide fully

 

 

into the magazine..

 

www.chpower.com

5

Operating Instructions

Operating Instructions

 

thumbwheel in place after each

7. Extend the wire latch and place over

(Continued)

 

 

 

adjustment..

 

the hooks on the nose..

4. Release the pusher.. Allow pusher to

3.

Make sure that

 

 

rest against nails.. The nailer is now

 

the trigger and

 

8. Close the latch by pushing the latch

loaded..

 

 

 

work contact

 

 

 

 

Rotate

up and in until the latch snaps into

 

 

 

 

element (WCE)

 

 

 

 

place..

UNLOADING THE Nailer

 

 

 

 

 

move freely up and down without

1. Always unload all fasteners before

 

9. Make sure the trigger and work

 

binding or sticking after each

 

contact element (WCE) move freely

removing tool from service..

 

 

adjustment..

 

 

 

up and down without sticking or

Unloading is the

 

 

 

 

 

 

 

 

 

 

Nail

Adjusting The Direction Of The

binding..

reverse of loading,

Pusher

except always

 

Mechanism

Exhaust

 

 

 

Nail Bypass Button

 

 

 

The NB356502 is

 

User-Maintenance

disconnect the

 

 

 

air hose before

 

 

equipped with an

 

Instructions

unloading..

 

 

adjustable direction

 

Technical Service

 

 

 

exhaust deflector.. This

 

2. Pull nail pusher

 

 

 

Please call our Tool Hotline at 1-800-

 

 

is intended to allow

 

mechanism back and

 

 

 

 

543-6400 with any questions regarding

 

the user to change the

 

press “Nail Bypass

 

 

 

 

the operation or repair of this tool or

 

direction of the exhaust..

 

Button..”

 

 

 

 

 

 

for additional copies of this manual..

 

 

Simply twist the deflector

 

 

 

 

 

3. Hold tool upright so

 

 

 

 

to any direction desired..

 

Fastener And Replacement

nails will slide out of

 

 

 

 

 

 

Parts

magazine..

 

 

Clearing A Jam From The Tool

 

 

Use only 15 gauge

 

 

 

1.

Disconnect the air

 

 

 

 

 

35° fasteners.

4. Release the Pusher..

 

 

supply from the tool..

 

 

 

 

Use only genuine Campbell Hausfeld

 

 

 

 

 

 

replacement parts. Never substitute

 

 

 

 

 

 

parts. Do not use modified parts or

 

 

 

2. Remove all nails from the magazine

parts which will not give equivalent

Adjusting

 

 

performance to the original equipment.

 

 

 

(see "Loading/

 

Tool performance, safety and durability

the Nail

 

 

 

Unloading The

 

could be reduced. When ordering

Penetration

COUNTER-

 

 

Nailer").. Failure to

 

replacement parts or fasteners, specify

 

CLOCKWISE

 

 

by part number.

The NB356502 is

CLOCKWISE

 

do so will cause the

 

 

 

 

 

 

 

 

 

equipped with an

 

 

 

nails to eject from the

 

Tool Repair

adjustable depth

 

 

 

front of the nailer..

 

Only qualified personnel should repair

of drive feature.. This allows the user to

 

 

 

3.

Undo latch by pulling

 

the tool and they should use genuine

determine how deep a fastener will be

 

 

out and down..

 

Campbell Hausfeld replacement parts

driven into the work surface..

 

 

 

 

 

The wire latch will

 

and accessories, or parts and accessories

 

 

 

 

 

1. Adjust the

 

 

 

disengage from the

 

which perform equivalently..

operating

 

 

 

hooks on the nose..

 

Assembly Procedure For Seals

pressure to a

 

 

4. The door can now be

 

 

 

 

When repairing a tool, the internal

pressure which

 

 

 

 

 

 

rotated, exposing the

 

will consistently

 

 

 

 

parts must be cleaned and lubricated..

 

 

 

jammed fastener..

 

drive the

 

 

 

 

Parker O-lube or equivalent must be

 

 

 

 

 

fasteners.. Do not exceed the

5.

Remove the jammed

 

used on all o-rings.. Each o-ring must be

maximum operating pressure of the

 

coated with O-lube before assembling..

nailer of 110 psi..

 

 

 

fastener, using pliers

 

A small amount of oil must be used on

2. To increase depth of drive, first

 

or a screwdriver if

 

all moving surfaces and pivots.. After

 

required..

 

reassembling, a few drops of 30W

pull up on the upper WCE, then

 

 

6.

Rotate door back into

 

non-detergent oil or equivalent, must

rotate thumbwheel to the left

 

 

the closed position..

 

be added through the air line before

(counter-clockwise)..

 

 

 

 

 

 

 

testing..

To decrease depth

 

 

 

 

 

 

 

 

 

of drive, rotate

 

Movement

 

 

Movement

Storage

thumbwheel to the

 

 

 

 

 

 

 

 

The stapler should be stored in a cool

right (clockwise).. Then release upper

 

 

 

 

 

 

dry place..

WCE into detents which hold the

 

 

 

 

 

 

 

www.chpower.com

 

 

 

 

 

 

6

NB356502

Fasteners Information

Nails used in the Campbell Hausfeld NB356502 Angle Finish Nailer will also work in Sears 18329, Porter Cable DA250, Senco SFN2B, SFN1 and SFN40..

Troubleshooting Chart

Stop using stapler immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center.

Symptom

Possible Cause(s)

Corrective Action

Air leaking at trigger valve

O-Rings in trigger valve housing are

Replace o-rings and check operation of Work

area..

damaged

Contact Element (WCE)

 

 

 

 

Air leaking between housing

1. Damaged O-Rings

1.

Replace o-rings

and nose..

2.

Damage to bumper

2.

Replace bumper

 

 

 

 

 

 

Air leaking between housing

1.

Loose screws

1.

Tighten screws

and cap..

2.

Damaged gasket

2.

Replace gasket

 

 

 

 

 

 

Nailer skips driving nail

1.

Worn bumper

1.

Replace bumper

 

2.

Dirt in nose piece

2.

Clean drive channel

 

3.

Dirt or damage prevent staples or pusher

3.

Clean magazine

 

 

from moving freely in magazine

 

 

 

4.

Damaged pusher spring

4.

Replace spring

 

5.

Inadequate air flow to stapler

5.

Check fitting, hose, or compressor

 

6.

Worn O-Ring on piston or lack of

6.

Replace and lubricate o-rings

 

 

lubrication

 

 

 

7.

Damaged O-Ring on trigger valve

7.

Replace o-rings

 

8.

Air leaks

8.

Tighten screws and fittings

 

9.

Cap gasket leaking

9.

Replace gasket

 

 

 

 

 

Nailer runs slow or has loss

1.

Nailer not lubricated sufficiently

1.

Lubricate nailer

of power

2.

Broken spring in cylinder cap

2.

Replace spring

 

 

3.

Exhaust port in cap is blocked

3.

Replace damaged internal parts

 

 

 

 

Nails are jammed in nailer

1. Guide on driver is worn

1.

Replace guide

 

2.

Nails are not correct size

2.

Use only recommended nails

 

3.

Nails are bent

3.

Replace with undamaged nails

 

4.

Magazine or nose screws are loose

4.

Tighten screws

 

5.

Driver is damaged

5.

Replace driver

www.chpower.com

7

Operating Instructions

Limited Warranty

1.DURATION: From the date of purchase by the original purchaser as follows: One (1) Year..

2.WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400

3..WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product..

4..WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer, stapler, air tool, spray gun, inflator or air accessory supplied or manufactured by Warrantor..

5..WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the duration of the warranty period..

6..WHAT IS NOT COVERED UNDER THIS WARRANTY:

A.Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION.. If this product is used for commercial, industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase.. Some States do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you..

B.ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT.. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you..

C.Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied with product.. Accident, purchaser's abuse, neglect or failure to operate products in accordance with instructions shall also include the removal or alteration of any safety devices.. If such safety devices are removed or altered, this warranty is void..

D.Normal adjustments which are explained in the owner’s manual(s) provided with the product..

E.Items or service that are normally required to maintain the product, i..e.. o-rings, springs, bumpers, debris shields, driver blades, fuses, batteries, gaskets, packings or seals, fluid nozzles, needles, sandblast nozzles, lubricants, material hoses, filter elements, motor vanes, abrasives, blades, cut-off wheels, chisels, chisel retainers, cutters, collets, chucks, rivet jaws, screw driver bits, sanding pads, back-up pads, impact mechanism, or any other expendable part not specifically listed.. These items will only be covered for ninety (90) days from date of original purchase.. Underlined items are warranted for defects in material and workmanship only..

7.RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or components which are defective, have malfunctioned and/or failed to conform within duration of the warranty period..

8.RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A.Provide dated proof of purchase and maintenance records..

B.Call Campbell Hausfeld (800) 543-6400 to obtain your warranty service options.. Freight costs must be borne by the purchaser..

C.Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s)..

9.WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts..

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights.. You may also have other rights which vary from state to state or country to country..

www.chpower.com

8

+ 16 hidden pages