Campbell Hausfeld IN628801AV User Manual
See Warranty on page 8 for important information about commercial use of this product.
STOP!
Operating Instructions HM7000 and HU2000
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
Oilless Compressors
Description
Portable oilless air compressors are for
home and workshop use. Cleaning or
replacement of the inlet filter on all
models and draining moisture from the
air receivers are required maintenance.
Safety Guidelines
This manual contains information that is
very important to know and understand.
This information is provided for SAFETY
and to PREVENT EQUIPMENT PROBLEMS.
To help recognize this information,
observe the following symbols.
Danger indicates
an imminently
hazardous situation which, if not avoided,
WILL result in death or serious injury.
Warning indicates
a potentially
hazardous situation which, if not avoided,
COULD result in death or serious injury.
Caution indicates a
potentially
hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
Notice indicates
important
information, that if not followed, MAY
cause damage to equipment.
DO NOT RETURN
THE PRODUCT TO
THE RETAILER!
Record the Model No., Serial No. and
date of purchase located on the base
below the pump in the space below.
Model No. ____________________
Serial No. ____________________
Date of purchase _________________
Retain these numbers for future
reference.
Breathable Air Warning
This compressor/pump is not
equipped and should not be
used “as is” to supply breathing
quality air. For any application of
air for human consumption, the
air compressor/pump will need
to be fitted with suitable in-line
safety and alarm equipment.
This additional equipment is
necessary to properly filter
and purify the air to meet
minimal specifications for Grade
D breathing as described in
Compressed Gas Association
Commodity Specification G 7.1
- 1966, OSHA 29 CFR 1910. 134,
and/or Canadian Standards
Associations (CSA).
DISCLAIMER OF WARRANTIES
In the event the compressor is
used for the purpose of breathing
air application and proper in-line
safety and alarm equipment is
not simultaneously used, existing
warranties shall be voided, and
Campbell Hausfeld disclaims any
liability whatsoever for any loss,
personal injury or damage.
Unpacking
When unpacking unit, inspect carefully
for any damage that may have occurred
during transit. Make sure any loose
fittings, bolts, etc., are tightened before
putting unit into service. In case of
questions, damaged or missing parts,
please call 1-800-543-6400 for customer
assistance. Have the serial number,
model number, and parts list (with
missing parts circled) before calling.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2009 Campbell Hausfeld/Scott Fetzer
General Safety
CALIFORNIA PROPOSITION 65
This product or
its power cord may
contain chemicals, including lead, known
to the State of California to cause cancer
and birth defects or other reproductive
harm. Wash hands after handling.
You can
create
dust when you cut, sand,
drill or grind materials such
as wood, paint, metal,
concrete, cement, or other
masonry. This dust often contains
chemicals known to cause cancer, birth
defects, or other reproductive harm.
Wear protective gear.
For parts, product & service information
visit www.chpower.com
GENERAL SAFETY INFORMATION
Air compressors are utilized in a variety
of air system applications. Because air
compressors and other components
(material pump, spray gun, filters,
lubrications, hoses, etc.) used make up
a high pressure pumping system, the
following safety precautions should be
observed at all times. Only persons well
acquainted with these rules of safe
operation should be allowed to use the
air compressor.
All electrical work
should be done by a
qualified (licensed or certified)
electrician. On a properly wired circuit,
the black wires supply a voltage
potential even when the unit is off.
IN628801AV 3/09
Portable Air Compressors
General Safety (Cont.)
1. Read instruction manuals for
each component carefully,
before attempting to assemble,
disassemble or operate your
particular system.
2. Wear safety glasses and
use hearing protection
when operating the
pump or unit.
3. Do not stand on or use the pump or
unit as a handhold.
4. Do not exceed pressure rating of
any component in system.
5. Protect material lines and air lines
from damage or puncture. Keep
hose and power cable away from
sharp objects, chemical spills, oil,
solvents, and wet floors.
6. Never point a spray gun at oneself
or any other person. Accidental
discharge may result in serious injury.
7. Check hoses for weak or worn
condition, before each use, making
certain all connections are secure;
do not use if deficiency is found.
Notify an authorized service facility
for examination or repair.
Do not run
unattended. Leaving
compressor in ON position may allow it to
turn on inadvertently. To prevent this and
possible damage from power surge, turn
to OFF position after each use.
8. Release all pressures within system
slowly; dust and debris may be
harmful.
Keep
fingers
away from a running
compressor; fast moving
and hot parts will cause
injury and/or burns.
Disconnect power
and depressurize
system before servicing air compressor!
9. Follow all local electrical and safety
codes, as well as the National Electrical
Code (NEC) and the Occupational
Safety and Health Act (OSHA).
10. Wiring and fuses should follow
electrical codes, current capacity, and
be properly grounded.
11. Electric motors must be securely and
adequately grounded. See grounding
instructions and extension cord
information, in this manual.
12. Always disconnect power source
before working on or near a motor, or
its connected load. If power disconnect
point is out-of-sight, lock it in the
open position and tag to prevent
unexpected application of power.
13. Guard all moving parts; keep
visitors away. Never allow children
in work area.
14. Use only a properly grounded
outlet that will accept a three
pronged plug, and wear shoes to
prevent shock hazards.
Be
careful
when touching exterior of
operating motor; it may be
hot enough to cause injury.
Compressor parts may be hot
even if the unit is stopped.
15. Protect power cable from coming in
contact with sharp objects.
16. Clean electrical or electronic
equipment with an approved cleaning
agent, such as dry, nonflammable
cleaning solvent.
Motors,
electrical
equipment and controls can
cause electrical arcs that
will ignite a flammable gas
or vapor. Never operate or repair the
unit near a flammable gas or vapor.
Never store flammable liquids or gases
in the vicinity of the compressor.
17. To reduce fire hazard,
keep engine/motor
exterior free of oil,
solvent, or grease.
18. To avoid spontaneous combustion,
discard waste rags into approved
metal waste cans.
19. NEVER reset safety valve or pressure
switch. Keep safety valve free from
paint and other accumulations. This
provides safety against over pressure.
Never remove or
attempt to adjust
safety valve. Keep safety valve free
from paint and other accumulations.
20. Do regular maintenance; keep all
nuts, bolts, and screws tight, to be
sure equipment is in safe working
condition .
21. Keep cleaning rags and other
flammable waste materials in a tightly
closed metal container and dispose of
later in the proper fashion.
22. Drain tanks of moisture after each
day’s use. If unit will not be used for
a while, it is best to leave drain cock
open until such time as it is to be used.
This will allow moisture to completely
drain out and help prevent corrosion
of inside of tank.
23. Inspect tank yearly for rust, pin holes
or any other imperfections that could
cause it to become unsafe. NEVER
weld or drill holes in air tank.
Never attempt
to repair or modify a
tank! Welding, drilling or any other
modification will weaken the tank resulting
in damage from rupture or explosion.
Always replace worn or damaged tanks.
Drain liquid from
tank daily.
SPRAYING PRECAUTIONS
Do not spray
flammable materials
in vicinity of open flame or near ignition
sources including the compressor unit.
24. Spray in a well ventilated area, to keep
fumes from collecting and causing
health and fire hazards.
25. Do not spray in vicinity of open flames
or other places where a spark can
cause ignition. Do not smoke when
spraying paint, insecticides, or other
flammable substances.
26. Use a respirator when spraying.
27. Do not direct paint or other sprayed
material at the compressor. Locate
compressor as far away from
the spraying area as possible to
minimize overspray accumulation
on the compressor.
28. When spraying or cleaning with
solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.
29. Do not smoke when spraying paint,
insecticides, or other flammable
substances.
30. Use a face mask/
respirator when
spraying and spray in a
well ventilated area to
prevent health and fire hazards.
31. Household use only.
32. To reduce the risk of electrical shock,
do not expose to rain. Store indoors.
www.chpower.com
2
HM7000 and HU2000
Assembly
ASSEMBLY TOOLS REQUIRED
Tools (not provided) for assembly:
- 2 14mm wrench or socket wrench
- 2 17mm wrench or socket wrench
FOOT ASSEMBLY (FIGURE 1)
Foot assembly kit includes:
- 1 rubber foot
- 1 bolt
- 2 washers
- 1 nut
Nut
Rubber Foot
Washer
Bolt
Figure 1 - Rubber foot installation
WHEEL ASSEMBLY (FIGURE 2)
Wheel assembly kit includes:
- 2 wheels*
- 2 axle bolts*
- 2 lock washers*
- 2 nuts*
The items marked with an asterisk (*)
were shipped loose with the unit.
Nut
Lock
Washer
Wheel
Axle Bolt
Figure 2 - Wheel assembly
1. Wheel has an offset hub. With offset
hub facing axle iron, assemble axle bolt
through holes in wheel and axle iron.
2. Place lock washer on axle bolt. Then
tighten nut securely to threaded
part of axle bolt.
3. Repeat procedure with other side.
HANDLE ASSEMBLY (FIGURE 3)
Never use the
handle to lift the
unit completely off the ground. Only
use the handle to lift one end so the
wheels may be used to move the unit.
Washer
✽ Wire and Terminal Guide
Wire Color Terminal Hot
Power cord White Line No
Motor cord White Load No
Power cord Black Line Yes
Motor cord Black Load Yes
(✽) When the unit is not in operation
3. Compressor should be located where
Tank
it can be directly plugged into an
outlet, but if this is not possible, an
extension cord may be used. It should
be selected using the extension cord
Handle
chart on page 3 as a guide.
4. To avoid loss of power and
Bolt
overheating, it is better to use
additional air hose instead of
extension cords to reach work area.
WIRING
1. Local electrical wiring codes
differ from area to area. Source
Figure 3 - Handle Assembly
wiring, plug and protector must
be rated for at least the amperage
Handle assembly kit includes:
- 1 handle
- 2 bolts
1. Insert ends of handle into tube
shaped brackets on tank.
2. Align screw holes.
3. Thread screw into hole until tight.
Installation
LOCATION
It is extremely important to install the
compressor in a clean, well ventilated area
where the surrounding air temperature
will not be more than 100°F.
A minimum clearance of 18 inches between
the compressor and a wall is required
because objects could obstruct air flow.
Do not locate the
compressor air inlet
near steam, paint spray, sandblast areas
or any other source of contamination. This
debris will damage the motor
Household use only. Store indoors.
and voltage indicated on motor
nameplate, and meet all electrical
codes for this minimum .
2. Use a slow blow fuse type T or a
circuit breaker.
Overheating, short
circuiting and fire
damage will result from inadequate
wiring, etc.
All wiring and
electrical
connections should be performed by a
qualified electrician. Installation must
be in accordance with local codes and
national electrical codes.
NOTE: 120 volt, compressor can be
operated on a 120 volt, 15 amp circuit
under the following conditions:
a. No other electrical appliances or
lights are connected to the same
branch circuit.
b. Voltage supply is normal.
c. Extension cords are of the
minimum gauge specified in this
ELECTRICAL INSTALLATION
1. Check and tighten all bolts, fittings,
etc., before operating compressor.
2. Operate compressor in a ventilated
area so that compressor may be
properly cooled.
instruction manual.
d. Circuit is equipped with a 15 amp
circuit breaker or a 15 amp slow
blow fuse type T.
3. If above conditions cannot be met
or if nuisance tripping of current
protection device occurs, it may be
necessary to operate compressor
from a 120 volt, 20 amp circuit.
Extension cords for 120V/10 Amp Unit
Length of Cord (ft) 25 50 100
Gauge of Cord 16 14 10
www.chpower.com
3
Portable Air Compressors
TEST
RESET
Installation (Cont.)
GROUNDING INSTRUCTIONS
This product must be grounded. In
the event of an electrical short circuit,
grounding reduces the risk of electric
shock by providing an escape wire
for the electric current. This product
is equipped with a cord having a
grounding wire with an appropriate
grounding plug. The plug must be
plugged into an outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
Grounding
Pin
Figure 4 - Grounding Method
Improper installation
of the grounding
plug is able to result in a risk of electric
shock. When repair or replacement of the
cord or plug is required, do not connect
the grounding wire to either flat blade
terminal. The wire with insulation having
an outer surface that is green with or
without yellow stripes is the grounding
wire.
Do not use adapter
with this product!
Never connect
green (or green and
yellow) wire to a live terminal.
Check with a qualified electrician
or serviceman when the grounding
instructions are not completely
understood, or when in doubt as
to whether the product is properly
grounded. Do not modify the plug
provided; if it does not fit the outlet,
have the proper outlet installed by a
qualified technician.
This product is for use on a nominal
120V circuit and has a grounding plug
similar to the plug illustrated in Figure
4. Only connect the product to an
outlet having the same configuration
as the plug. Do not use an adapter
with this product.
EXTENSION CORDS
To avoid loss of
power and
overheating, it is better to use
additional air hose instead of extension
cords to reach work area.
Grounded
Outlet
MOISTURE IN COMPRESSED AIR
Moisture in compressed air will form into droplets as it comes from an air
compressor pump. When humidity is high or when a compressor is in continuous use
for an extended period of time, this moisture will collect in the tank. When using a
paint spray or sandblast gun, this water will be carried from the tank through the
hose, and out of the gun as droplets mixed with the spray material.
IMPORTANT:
This condensation will cause water spots in a paint job, especially
when spraying other than water based paints. If sandblasting, it will cause the sand
to cake and clog the gun, rendering it ineffective. A filter in the air line, located as
near to the gun as possible, will help eliminate this moisture.
Use only a 3-wire extension cord that
has a 3-blade grounding plug, and
a 3-slot receptacle that accepts the
plug on the product. Make sure your
extension cord is not damaged. When
using an extension cord, be sure to use
one heavy enough to carry the current
your product draws. An undersized
cord results in a drop in line voltage
and loss of power and overheating.
[The table on page 3 shows the correct
size to use depending on cord length
and nameplate ampere rating. When
in doubt, use the next heavier gauge.
The smaller the gauge number, the
heavier the cord.]
Operation
• Pressure Switch - ON/OFF Switch
(Figure 5) - In the ON position, the
compressor shuts off automatically
when tank pressure reaches the
maximum preset pressure. In the
OFF
position, the compressor will
not operate. This switch should be in
the OFF position when connecting
or disconnecting the power cord
from the electrical outlet or when
changing air tools.
•
Regulator - The regulator controls
the amount of air pressure released
at the hose outlet.
•
ASME Safety Valve - This valve
automatically releases air if the
tank pressure exceeds the preset
maximum.
•
Exhaust Tube - This tube carries
compressed air from the pump to
the check valve. This tube becomes
very hot during use. To avoid the
risk of severe burns, never touch
the exhaust tube.
•
Check Valve - A one-way valve
that allows air to enter the tank, but
prevents air in the tank from flowing
back into the compressor pump.
•
Handle - Designed to move the
compressor.
•
Drain Valve - This valve is located on
the side of the tank. Use this valve to
drain moisture from the tank daily to
reduce the risk of corrosion.
Drain liquid from
tank daily.
Reduce tank pressure below 10 psi, then
drain moisture from tank daily to avoid
tank corrosion. Drain moisture from
tank by opening the drain valve located
Regulator Knob
Pressure
Switch
underneath or on the side of the tank.
BEFORE FIRST START-UP
BREAK-IN PROCEDURE
(Complete this procedure before using
compressor for the first time. Once
completed, it is not necessary to repeat.)
1. Turn regulator knob fully clockwise
(to the right) to open air flow and
open drain valve.
2. Turn ON/OFF
switch to OFF position.
3. Plug in power cord.
Figure 5 - ON/OFF Switch
4. Turn ON/OFF
switch to ON position
and run compressor for 30 minutes.
www.chpower.com
4
HM7000 and HU2000
Operation (Cont.)
5. Turn ON/OFF switch to OFF position.
6. Unplug power cord.
7. Close drain valve.
The compressor is now ready for use.
BEFORE EACH START-UP
OPERATING PROCEDURE
1. Turn regulator knob fully counter
clockwise (to the left) to close air flow.
2. Connect air hose to outlet of
regulator.
3. Turn On/Off Switch to OFF position.
4. Plug in power cord.
5. Turn On/Off Switch to ON position
and let compressor run until it reaches
automatic shutoff pressure.
6. Attach tire chuck or tool to end of hose.
7. Turn regulator knob clockwise (to
the right) to desired pressure of tool
being used.
ON/OFF CYCLING OF COMPRESSOR
In the ON position, the compressor
pumps air into the tank. When a shut-off
(preset “cut-out”) pressure is reached,
the compressor automatically shuts off.
If the compressor is left in the ON
position and air is depleted from
the tank by use of a tire chuck, tool,
etc., the compressor will restart
automatically at its preset “cut-in”
pressure. When a tool is being used
continuously, the compressor will cycle
on and off automatically.
In the OFF position, the pressure switch
cannot function and the compressor
will not operate. Make sure switch
is in OFF position when connecting
or disconnecting power cord from
electrical outlet.
ASME SAFETY VALVE
Do not remove or
attempt to adjust
the safety valve!
Check the safety valve by performing
the following steps:
1. Plug the compressor in and run until
shut off pressure is reached (see
Operating Procedure).
2. Wearing safety glasses, pull the ring
on the safety valve (see Figure 6) to
release pressure from compressor
tank. Use your other hand to deflect
fast-moving air from being directed
toward your face.
Figure 6
3. The safety valve should automatically
close when pressure in the tank has
been released. If the safety valve does
not allow air to be released when you
pull on the ring, or if it does not close
automatically, it MUST be replaced.
Safety valve must
be replaced if it
cannot be actuated or it leaks air after
ring is released.
PRESSURE GAUGES
Gauge attached to regulator indicates
air pressure going to hose (and any tool
attached to end of hose).
Gauge attached to pressure switch
indicates air pressure in tank.
Maintenance
Release all pressure
and disconnect
power before making any repair.
1. Check compressor for any visible
problems, especially check air filter to
be sure it is clean.
2. Pull ring on safety valve and allow it to
snap back to normal position (Figure 6).
Safety valve must
be replaced if it
cannot be actuated or it leaks air after ring
is released.
3. Daily with compressor shut off:
Depressurize system prior to draining
tank. Drain moisture from tanks by
opening drain cocks on the side or
underneath end of tank.
NOTE: Drain cup should be emptied
regularly.
Figure 7
Do not remove drain
plug with tank under pressure.
4. Turn power OFF and clean dust and dirt
from motor, tank, air lines and pump
cooling fins.
NOTE: The air filter in the filter housing on
the side of the head must be checked and
cleaned periodically, more often if used
under very dusty conditions or when a
great deal of fog from spraying is allowed
to circulate near unit.
IMPORTANT:
Unit should be located as far
from spraying area as hose will allow to
prevent over-spray from clogging filter.
DRAIN CUP VALVE OPERATION
1. To open, slowly turn drain knob
counter-clockwise 2 to 4 turns until
water or air begins to escape into
the cup.
NOTE: Do not turn or force the knob
more than 2 to 4 turns, taking care not
to remove the knob.
2. To prevent overflow, monitor the cup
at all times when draining.
3. When the cup is partially full or
draining is complete (whichever
happens first), shut off drain by
turning knob clockwise.
4. Empty the cup, disposing of the
water properly.
5. If water remains in tank, continue
draining until the unit is empty.
Turn counterclockwise to
drain
Turn clockwise
to close
Figure 8 - Drain cup valve
FILTER REMOVAL, INSPECTION AND
REPLACEMENT
To change a filter, pull off the filter
housing cover. If filter element is dirty,
rotate filter cover so the holes line up with
clean element material and snap cover
onto housing. If filter element has no clean
areas, replace element or entire filter.
www.chpower.com
5
Portable Air Compressors
LUBRICATION
This is an oilless type compressor requiring
no lubrication.
THERMAL OVERLOAD PROTECTOR
Turn off the pressure switch or unplug
compressor for 20 minutes and allow it to
cool. Reset the unit. Switch unit to OFF and
turn ON again to resume work.
This compressor is
equipped with a
manual reset thermal overload protector
which will shut off motor if it becomes
overheated.
Notes
If thermal overload protector shuts
motor off frequently look for the
following causes.
1. Low voltage.
2. Wrong gauge wire or length of
extension cord.
3. Clogged air filter.
4. Lack of proper ventilation.
The motor must be
allowed to cool down
before start-up is possible. The motor will
automatically restart without warning if
left plugged into electrical outlet, if the
motor is turned on.
STORAGE
1. When not in use, hose and
compressor should be stored in a
cool dry place.
2. Tank should be drained of moisture.
3. Hose should be disconnected and
hung open ends down to allow any
moisture to drain.
www.chpower.com
6
Troubleshooting Chart
Symptom Possible Cause(s) Corrective Action
Compressor will not run
1. Loss of power or overheating
2. No electrical power
3. Blown fuse
4. Breaker open
5. Thermal overload open
6. Pressure switch bad
1. Check for proper use of extension cord (see
EXTENSION CORDS, page 3)
2. Plugged in? Check fuse/breaker or motor overload
3. Replace blown fuse
4. Reset, determining why problem happened
5. Motor will restart when cool; turn off compressor and
wait 20 minutes.
6. Replace
HM7000 and HU2000
Motor hums but cannot
run or runs slowly
Fuses blow/circuit
breaker trips repeatedly
Thermal overload
protector cuts out
repeatedly
Air receiver pressure
drops when compressor
shuts off
1. Low voltage
2. Wrong gauge wire or length of
extension cord
3. Shorted or open motor winding
4. Defective check valve or unloader
1. Incorrect size fuse, circuit overloaded
2. Wrong gauge wire or length of
extension cord
3. Defective check valve or under loader
1. Low voltage
2. Clogged air filter
3. Lack of proper ventilation/room
temperature too high
4. Wrong gauge wire or length of
extension cord
1. Loose connections (fittings, tubing,
etc.)
2. Loose drain lock
3. Check valve leaking
1. Check with voltmeter
2. Check gauge chart, under Operation for proper
gauge wire and cord length
3. Replace motor
4. Replace or repair
1. Check for proper fuse, use time-delay fuse.
Disconnect other electrical appliances from circuit or
operate compressor on its own branch circuit
2. Check gauge chart, under Operation
3. Replace or repair
1. Check with voltmeter
2. Clean filter (see Maintenance section)
3. Move compressor to well ventilated area
4. Check gauge chart, under Operation
1. Check all connections with soap and water solution
and tighten
2. Tighten
3. Disassemble check valve assembly, clean or replace
Do not disassemble check valve
with air in tank; bleed tank
Excessive moisture in
discharge air
Compressor runs
continuously
Compressor vibrates
Air output lower than
normal
1. Excessive water in air receiver
2. High humidity
1. Defective pressure switch
2. Excessive air usage
3. Check valve leaking
Loose mounting bolts
1. Broken inlet valves
2. Intake filter dirty
3. Connections leaking
1. Drain receiver
2. Move to area of less humidity; use air line filter
1. Replace switch
2. Decrease air usage; compressor not large enough for
a requirement
3. Disassemble check valve assembly, clean or replace
Tighten
1. Have authorized service representative repair unit
2. Clean or replace intake filter
3. Tighten connections
www.chpower.com
7
Portable Air Compressors
Limited Warranty
1. DURATION: From the date of purchase by the original purchaser as follows: Standard Duty - One Year; Serious Duty - Two
Years; Extreme Duty - Three Years; Maxus Model Series - Five Years.
2. WHO GIVES THIS WARRANTY (WARRANTOR):
Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell
Hausfeld compressor.
4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld air compressor.
5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects due to material and workmanship with the exceptions
noted below.
6. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM
THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this compressor is used for commercial, industrial
or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Extreme Duty Contractor
Compressors are not limited to a ninety (90) day warranty when used in contractor applications. Four cylinder singlestage and two-stage compressors are not limited to a ninety (90) day warranty when used in commercial or industrial
applications. Some States do not allow limitations on how long an implied warranty lasts, so the above limitations may
not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT,
FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or
limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with
instructions provided in the owner’s manual(s) supplied with compressor.
D. Pre-delivery service, i.e. assembly, oil or lubricants, and adjustment.
E. Items or service that are normally required to maintain the product, i.e. lubricants, filters and gaskets, etc.
F. Gasoline engines and components are expressly excluded from coverage under this limited warranty. The Purchaser
must comply with the warranty given by the engine manufacturer which is supplied with the product.
G. Additional items not covered under this warranty:
1. All Compressors
a. Any component damaged in shipment or any failure caused by installing or operating unit under conditions not in
accordance with installation and operation guidelines or damaged by contact with tools or surroundings.
b. Pump or valve failure caused by rain, excessive humidity, corrosive environments or other contaminants.
c. Cosmetic defects that do not interfere with compressor functionality.
d. Rusted tanks, including but not limited to rust due to improper drainage or corrosive environments.
e. Electric motors, check valves and pressure switches after the first year of ownership.
f. Drain cocks.
g. Damage due to incorrect voltage or improper wiring.
h. Other items not listed but considered general wear parts.
i. Pressure switches, air governors and safety valves modified from factory settings.
2. Lubricated Compressors
a. Pump wear or valve damage caused by using oil not specified.
b. Pump wear or valve damage caused by any oil contamination or by failure to follow proper oil maintenance
guidelines.
3. Belt Drive / Direct Drive / Gas Driven Compressors
a. Belts.
b. Ring wear or valve damage from inadequate filter maintenance.
c. Manually adjusted load/unload and throttle control devices.
7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, compressor or
component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period.
8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A. Provide dated proof of purchase and maintenance records.
B. Portable compressors or components must be delivered or shipped to the nearest Campbell Hausfeld Authorized Service
Center. Freight costs, if any, must be borne by the purchaser.
C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be
scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of
replacement parts.
This Limited Warranty applies in the U.S., Canada and Mexico only and gives you specific legal rights. You may also have other
rights which vary from State to State or country to country.
www.chpower.com
8
Loading...