®
|
OPA234 |
|
OPA2234 |
OPA4234 |
|
|
|||
|
|
|
|
|
|
OPA234 |
OPA2234 |
|
|
|
|
|
||
|
|
|
OPA4234 |
|
|
OPA234 |
|
|
For most current data sheet and other product information, visit www.burr-brown.com
OPA234
OPA2234
OPA4234
Low Power, Precision
SINGLE-SUPPLY OPERATIONAL AMPLIFIERS
FEATURES
● WIDE SUPPLY RANGE:
Single Supply: VS = +2.7V to +36V Dual Supply: VS = ±1.35V to ±18V
●GUARANTEED PERFORMANCE: +2.7V, +5V, and ±15V
●LOW QUIESCENT CURRENT: 250μA/amp
●LOW INPUT BIAS CURRENT: 25nA max
●LOW OFFSET VOLTAGE: 100μV max
●HIGH CMRR, PSRR, and AOL
●SINGLE, DUAL, and QUAD VERSIONS
DESCRIPTION
The OPA234 series low cost op amps are ideal for single supply, low voltage, low power applications. The series provides lower quiescent current than older “1013”-type products and comes in current industrystandard packages and pinouts. The combination of low offset voltage, high common-mode rejection, high power supply rejection, and a wide supply range provides excellent accuracy and versatility. Single, dual, and quad versions have identical specifications for maximum design flexibility. These general purpose op amps are ideal for portable and battery powered applications.
OPA234 series op amps operate from either single or dual supplies. In single supply operation, the input com- mon-mode range extends below ground and the output can swing to within 50mV of ground. Excellent phase margin makes the OPA234 series ideal for demanding applications, including high load capacitance. Dual and quad designs feature completely independent circuitry for lowest crosstalk and freedom from interaction.
Single version packages are DIP-8, SO-8 surface-mount, and a space-saving MSOP-8 surface-mount. Dual packages are DIP-8 and SO-8 surface-mount. Quad packages are DIP-14 and SO-14 surface-mount. All are specified for –40C° to +85°C operation.
|
|
|
OPA234 |
|
|||||||
Offset Trim |
|
|
|
|
|
|
|
|
|
|
NC |
1 |
|
|
|
|
|
|
|
|
8 |
||
–In |
|
|
|
|
|
|
|
|
|
|
V+ |
|
|
|
|
|
|
|
|
|
|
||
2 |
|
|
|
|
|
|
|
|
7 |
||
|
|
|
|
|
|
|
|
||||
+In |
|
|
|
|
|
|
|
|
|
|
Output |
|
|
|
|
|
|
|
|
|
|
||
3 |
|
|
|
|
|
|
|
|
6 |
||
V– |
|
|
|
|
|
|
|
|
|
|
Offset Trim |
|
|
|
|
|
|
|
|
|
|
||
4 |
|
|
|
|
|
|
|
|
5 |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
8-Pin DIP, SO-8, MSOP-8 |
|
|
|
|
OPA2234 |
|
|
||||||||
Out A |
|
|
|
|
|
|
|
|
|
|
|
|
V+ |
1 |
|
|
|
|
|
|
|
|
|
|
8 |
||
–In A |
|
|
A |
|
Out B |
||||||||
|
|
|
|||||||||||
2 |
|
7 |
|||||||||||
+In A |
|
|
|
|
|
|
|
|
B |
|
–In B |
||
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|||||
3 |
|
|
|
|
|
|
|
6 |
|||||
V– |
|
|
|
|
|
|
|
|
|
|
|
|
+In B |
|
|
|
|
|
|
|
|
|
|
|
|
||
4 |
|
|
|
|
|
|
|
|
|
|
5 |
||
|
|
8-Pin DIP, SO-8 |
|
|
|||||||||
|
|
|
|
OPA4234
Out A |
1 |
–In A |
2 |
|
A |
+In A |
3 |
V+ |
4 |
+In B |
5 |
|
B |
–In B |
6 |
Out B |
7 |
14 |
Out D |
13 |
–In D |
D |
|
12 |
+In D |
11 |
V– |
10 |
+In C |
C |
|
9 |
–In C |
8 |
Out C |
14-Pin DIP
SO-14
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 •mmediateI Product Info: (800) 548-6132
®
|
PDS-1318B1 |
OPA234, 2234, 4234 |
|
© 1996 Burr-Brown Corporation |
Printed in U.S.A., May, |
2000 |
SPECIFICATIONS: VS = +5V
At TA = 25°C, VS = +5V, RL = 10kW connected to VS /2 and VOUT = VS /2, unless otherwise noted.
|
|
|
|
|
|
|
|
|
OPA234PA, UA, EA |
|
|
|
|
|
||
|
|
|
|
|
OPA234P, U, E |
OPA2234PA, UA |
|
|
|
|
|
|||||
|
|
|
|
|
OPA2234P, U |
|
OPA4234PA, UA, U |
|
|
|
|
|
||||
PARAMETER |
|
CONDITION |
MIN |
TYP |
|
MAX |
MIN |
TYP |
MAX |
UNITS |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
OFFSET VOLTAGE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Input Offset Voltage |
VOS |
VCM = 2.5V |
|
±40 |
|
±100 |
|
|
±250 |
mV |
||||||
OPA234E, EA |
|
|
|
|
|
±100 |
|
±150 |
|
|
±350 |
mV |
||||
vs Temperature(1) |
dVOS/dT |
Operating Temperature Range |
|
±0.5 |
|
±3 |
|
|
|
mV/°C |
||||||
vs Power Supply |
PSRR |
VS = +2.7V to +30V, VCM = 1.7V |
|
3 |
|
10 |
|
|
20 |
mV/V |
||||||
vs Time |
|
|
|
|
|
0.2 |
|
|
|
|
|
mV/mo |
||||
Channel Separation (Dual, Quad) |
|
|
|
|
|
0.3 |
|
|
|
|
|
mV/V |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
INPUT BIAS CURRENT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Input Bias Current(2) |
I |
V |
CM |
= 2.5V |
|
–15 |
|
–30 |
|
|
–50 |
nA |
||||
|
B |
|
|
|
±1 |
|
±5 |
|
|
|
|
|
|
|
|
|
Input Offset Current |
IOS |
VCM = 2.5V |
|
|
|
|
|
nA |
||||||||
NOISE |
|
f = 1kHz |
|
|
|
|
|
|
|
|
|
|
|
|
||
Input Voltage Noise Density |
vn |
|
|
|
|
25 |
|
|
|
|
|
nV/Ö |
Hz |
|
||
Current Noise Density |
in |
|
|
|
|
80 |
|
|
|
|
|
fA/Ö |
Hz |
|
|
|
INPUT VOLTAGE RANGE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Common-Mode Voltage Range |
|
|
|
|
–0.1 |
|
|
(V+) –1 |
|
|
|
V |
||||
Common-Mode Rejection |
CMRR |
VCM = –0.1V to 4V |
91 |
106 |
|
|
86 |
|
|
dB |
||||||
INPUT IMPEDANCE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Differential |
|
|
|
|
|
107 || 5 |
|
|
|
|
|
W || pF |
||||
Common-Mode |
|
VCM = 2.5V |
|
1010 || 6 |
|
|
|
|
|
W || pF |
||||||
OPEN-LOOP GAIN |
|
VO = 0.25V to 4V |
|
|
|
|
|
|
|
|
|
|
|
|
||
Open-Loop Voltage Gain |
AOL |
RL = 10kW |
108 |
120 |
|
|
100 |
|
|
dB |
||||||
|
|
RL = 2kW |
86 |
96 |
|
|
86 |
|
|
dB |
||||||
FREQUENCY RESPONSE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Gain-Bandwidth Product |
GBW |
CL = 100pF |
|
0.35 |
|
|
|
|
|
MHz |
||||||
Slew Rate |
SR |
|
|
|
|
0.2 |
|
|
|
|
|
V/ms |
||||
Settling Time: 0.1% |
|
G = 1, 3V Step, CL = 100pF |
|
15 |
|
|
|
|
|
ms |
||||||
0.01% |
|
G = 1, 3V Step, CL = 100pF |
|
25 |
|
|
|
|
|
ms |
||||||
Overload Recovery Time |
|
(VIN) (Gain) = VS |
|
16 |
|
|
|
|
|
ms |
||||||
OUTPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Voltage Output: Positive |
|
RL = 10kW to VS/2 |
(V+) –1 |
(V+) –0.65 |
|
|
|
|
|
V |
||||||
Negative |
|
RL = 10kW to VS/2 |
0.25 |
0.05 |
|
|
|
|
|
V |
||||||
Positive |
|
RL = 10kW to Ground |
(V+) –1 |
(V+) –0.65 |
|
|
|
|
|
V |
||||||
Negative |
|
RL = 10kW to Ground |
0.1 |
0.05 |
|
|
|
|
|
V |
||||||
Short-Circuit Current |
ISC |
|
|
|
|
±11 |
|
|
|
|
|
mA |
||||
Capacitive Load Drive (Stable Operation)(3) |
|
G = +1 |
|
1000 |
|
|
|
|
|
pF |
||||||
POWER SUPPLY |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Specified Operating Voltage |
|
|
|
|
|
+5 |
|
|
|
|
|
V |
||||
Operating Voltage Range |
|
|
|
|
+2.7 |
|
|
+36 |
|
|
|
V |
||||
Quiescent Current (per amplifier) |
IQ |
|
IO = 0 |
|
250 |
|
300 |
|
|
|
mA |
|||||
TEMPERATURE RANGE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Specified Range |
|
|
|
|
–40 |
|
|
+85 |
|
|
|
°C |
||||
Operating Range |
|
|
|
|
–40 |
|
|
+125 |
|
|
|
°C |
||||
Storage |
θJA |
|
|
|
–55 |
|
|
+125 |
|
|
|
°C |
||||
Thermal Resistance |
|
|
|
|
|
|
|
|
|
|
°C/W |
|||||
8-Pin DIP |
|
|
|
|
|
100 |
|
|
|
|
|
|||||
SO-8 Surface-Mount |
|
|
|
|
|
150 |
|
|
|
|
|
°C/W |
||||
MSOP-8 Surface-Mount |
|
|
|
|
|
220 |
|
|
|
|
|
°C/W |
||||
14-Pin DIP |
|
|
|
|
|
80 |
|
|
|
|
|
°C/W |
||||
SO-14 Surface-Mount |
|
|
|
|
|
110 |
|
|
|
|
|
°C/W |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Specifications same as OPA234P,U,E.
NOTES: (1) Guaranteed by wafer-level test to 95% confidence level. (2) Positive conventional current flows into the input terminals. (3) See “Small-Signal Overshoot vs Load Capacitance” typical curve.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.
®
|
OPA234, 2234, 4234 |
2 |
|
SPECIFICATIONS: VS = +2.7V
At TA = 25°C, VS = +2.7V, RL = 10kW connected to VS /2 and VOUT = VS /2, unless otherwise noted.
|
|
|
|
|
|
|
OPA234PA, UA, EA |
|
|
|
|
|
||
|
|
|
OPA234P, U, E |
OPA2234PA, UA |
|
|
|
|
|
|||||
|
|
|
OPA2234P, U |
|
OPA4234PA, UA, U |
|
|
|
|
|
||||
PARAMETER |
|
CONDITION |
MIN |
TYP |
|
MAX |
MIN |
TYP |
MAX |
UNITS |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
OFFSET VOLTAGE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Input Offset Voltage |
VOS |
VCM = 1.35V |
|
±40 |
|
±100 |
|
|
±250 |
mV |
||||
OPA234E, EA |
|
|
|
±100 |
|
±150 |
|
|
±350 |
mV |
||||
vs Temperature(1) |
dVOS/dT |
Operating Temperature Range |
|
±0.5 |
|
±3 |
|
|
|
mV/°C |
||||
vs Power Supply |
PSRR |
VS = +2.7V to +30V, VCM = 1.7V |
|
3 |
|
10 |
|
|
20 |
mV/V |
||||
vs Time |
|
|
|
0.2 |
|
|
|
|
|
mV/mo |
||||
Channel Separation (Dual, Quad) |
|
|
|
0.3 |
|
|
|
|
|
mV/V |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
INPUT BIAS CURRENT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Input Bias Current(2) |
I |
V = 1.35V |
|
–15 |
|
–30 |
|
|
–50 |
nA |
||||
|
B |
CM |
|
±1 |
|
±5 |
|
|
|
|
|
|
|
|
Input Offset Current |
IOS |
VCM = 1.35V |
|
|
|
|
|
n |
||||||
NOISE |
|
f = 1kHz |
|
|
|
|
|
|
|
|
|
|
|
|
Input Voltage Noise Density |
vn |
|
|
25 |
|
|
|
|
|
nV/Ö |
|
|
||
|
|
|
|
|
|
|
Hz |
|||||||
Current Noise Density |
in |
|
|
80 |
|
|
|
|
|
fA/Ö |
|
|
|
|
|
|
|
|
|
|
Hz |
||||||||
INPUT VOLTAGE RANGE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Common-Mode Voltage Range |
|
|
–0.1 |
|
|
(V+) –1 |
|
|
|
V |
||||
Common-Mode Rejection |
CMRR |
VCM = –0.1V to 1.7V |
91 |
106 |
|
|
86 |
|
|
dB |
||||
INPUT IMPEDANCE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Differential |
|
|
|
107 || 5 |
|
|
|
|
|
W || pF |
||||
Common-Mode |
|
VCM = 1.35V |
|
1010 || 6 |
|
|
|
|
|
W || pF |
||||
OPEN-LOOP GAIN |
|
VO = 0.25V to 1.7V |
|
|
|
|
|
|
|
|
|
|
|
|
Open-Loop Voltage Gain |
AOL |
RL = 10kW |
108 |
125 |
|
|
100 |
|
|
dB |
||||
|
|
RL = 2kW |
86 |
96 |
|
|
86 |
|
|
dB |
||||
FREQUENCY RESPONSE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Gain-Bandwidth Product |
GBW |
CL = 100pF |
|
0.35 |
|
|
|
|
|
MHz |
||||
Slew Rate |
SR |
|
|
0.2 |
|
|
|
|
|
V/ms |
||||
Settling Time: 0.1% |
|
G = 1, 1V Step, CL = 100pF |
|
6 |
|
|
|
|
|
ms |
||||
0.01% |
|
G = 1, 1V Step, CL = 100pF |
|
16 |
|
|
|
|
|
ms |
||||
Overload Recovery Time |
|
(VIN) (Gain) = VS |
|
8 |
|
|
|
|
|
ms |
||||
OUTPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Voltage Output: Positive |
|
RL = 10kW to VS/2 |
(V+) –1 |
(V+) –0.6 |
|
|
|
|
|
V |
||||
Negative |
|
RL = 10kW to VS/2 |
0.25 |
0.05 |
|
|
|
|
|
V |
||||
Positive |
|
RL = 10kW to Ground |
(V+) –1 |
(V+) –0.65 |
|
|
|
|
|
V |
||||
Negative |
|
RL = 10kW to Ground |
0.1 |
0.05 |
|
|
|
|
|
V |
||||
Short-Circuit Current |
ISC |
|
|
±8 |
|
|
|
|
|
mA |
||||
Capacitive Load Drive (Stable Operation)(3) |
G = +1 |
|
1000 |
|
|
|
|
|
pF |
|||||
POWER SUPPLY |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Specified Operating Voltage |
|
|
|
+2.7 |
|
|
|
|
|
V |
||||
Operating Voltage Range |
|
|
+2.7 |
|
|
+36 |
|
|
|
V |
||||
Quiescent Current (per amplifier) |
IQ |
IO = 0 |
|
250 |
|
300 |
|
|
|
mA |
||||
TEMPERATURE RANGE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Specified Range |
|
|
–40 |
|
|
+85 |
|
|
|
°C |
||||
Operating Range |
|
|
–40 |
|
|
+125 |
|
|
|
°C |
||||
Storage |
θJA |
|
–55 |
|
|
+125 |
|
|
|
°C |
||||
Thermal Resistance |
|
|
|
|
|
|
|
|
°C/W |
|||||
8-Pin DIP |
|
|
|
100 |
|
|
|
|
|
|||||
SO-8 Surface-Mount |
|
|
|
150 |
|
|
|
|
|
°C/W |
||||
MSOP-8 Surface-Mount |
|
|
|
220 |
|
|
|
|
|
°C/W |
||||
14-Pin DIP |
|
|
|
80 |
|
|
|
|
|
°C/W |
||||
SO-14 Surface-Mount |
|
|
|
110 |
|
|
|
|
|
°C/W |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Specifications same as OPA234P,U,E.
NOTES: (1) Guaranteed by wafer-level test to 95% confidence level. (2) Positive conventional current flows into the input terminals. (3) See “Small-Signal Overshoot vs Load Capacitance” typical curve.
®
3 |
OPA234, 2234, 4234 |
|
|