DECT Repeater
User guide
Introduction
2
IMPORTANT
It is possible to roam between the
Repeater and the telephone base
station, however, call handover
during conversation is not always
guaranteed.
The registration of Repeaters to the
telephone base station does not
reduce the number of handsets that
can be registered to the telephone
base station.
The BT DECT Repeater is compatible
with the following products:
BT Diverse 7110+
BT Diverse 7150+
BT Diverse 7410+
BT Diverse 7450+
BT Diverse 7460+
If you experience any problems, please call the Helpline on Freephone 0800 218 2182* or visit www.bt.com/producthelp
BT Diverse 6210
BT Diverse 6250
BT Diverse 6350
BT Diverse 6410
BT Diverse 6450
BT Freestyle 7250
BT Freestyle 7310
The BT DECT Repeater lets you extend the coverage of your
telephone system in all directions, including up and down.
Up to five Repeaters can be registered to a single telephone base
station (depending on how many your base station supports).
Each Repeater can have up to two calls active at any time
(one external call and one internal call).
When registered to the telephone base station, the Repeater’s
coverage area overlaps the coverage area of the base station, the
base can hand-off calls to the Repeater as the user moves from
one coverage area to another. When connected to the Repeater,
the DECT handset operates in the exactly same way as it does
when connected to the base station, and the hand-off from the
base station to the Repeater is completely invisible to the user.
Getting to know your Repeater
Setup button
Used for registration/
de-registration
LED indicator
Off = Power supply is off
Red/Blue = In registration mode
Blue (Triple flash) = Registration completed successfully
Blue (Steady) = Good link to telephone base station
If you experience any problems, please call the Helpline on Freephone 0800 218 2182* or visit www.bt.com/producthelpIf you experience any problems, please call the Helpline on Freephone 0800 218 2182* or visit www.bt.com/producthelp
Blue (Double flash) = Repeater in use with good signal
Purple (Steady) = Weak link to telephone base station
Purple (Double flash) = Repeater in use with weak link
to base station
Red (Steady) = No link to telephone base station
3
Setting up
4
Need help?
If you have any problems setting up or
using your BT DECT Repeater please
contact the Helpline on Freephone
0800 218 2182*.
Alternatively, you may find
the answer in ‘Help’ at the
back of this guide or online at
www.bt.com/producthelp
* Calls made from within the
UK mainland network are free.
Mobile and International
call costs may vary.
Warning
Only use the power adaptor
supplied otherwise your product
may not work and you could
damage the product.
Connect the mains power adaptor
Plug the small end of the power adaptor cable into the socket on
the back of the Repeater.
Mains power adaptor cable
Then plug the other end into the mains wall socket but don’t
switch the power on at the wall socket yet.
Use a power socket close to your telephone base station. This
is because during the registration process, the telephone base
station needs to be near the Repeater. You can relocate your
Repeater after registration is complete.
If you experience any problems, please call the Helpline on Freephone 0800 218 2182* or visit www.bt.com/producthelp
Automatic registration to the telephone base station
1. Before beginning registration, make sure that all unregistered
Repeaters are switched off.
2. Turn on the Repeater mode in the telephone base station that
you will be registering the Repeater to. This varies dependant on
the product, the instruction can be found in the User guide,
provided with the telephone base station.
3. Put the telephone base station into registration mode, this is
normally done by pressing and holding the Find button, but
again consult the User guide, provided with the base station.
4. Switch on the power to the Repeater at the wall socket and the
Repeater will register automatically. The LED on the Repeater
will toggle between Red and Blue, followed by a triple blue flash
to confirm that registration is complete. The LED will remain blue
to indicate that the registration is complete.
5. You can now safely disconnect the power and move the Repeater
to your selected location. The Repeater will remain registered to
the telephone base station.
If you experience any problems, please call the Helpline on Freephone 0800 218 2182* or visit www.bt.com/producthelpIf you experience any problems, please call the Helpline on Freephone 0800 218 2182* or visit www.bt.com/producthelp
Setting up
If the LED continues to flash red, try
registering the Repeater again.
5
Loading...