for Models
B60R, B60RP, B60RDA
The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage “ within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
2.
4.
two blades with one wider than the other. A grounding type plug has two blades and a third
tacles, and the point where they exit from the apparatus.
sold with the apparatus. When a cart is used use caution when moving the cart/appa
THIS APPARATUS TO RAIN OR MOISTURE”.
THE POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE”.
Thank you for purchasing a Bryston B60 integrated
years of musical enjoyment. We would welcome any
suggestions or comments you may have regarding the
Bryston recommends that you retain the original
shipping box and packaging material for future use if
You may place your B60 integrated amplifier in any
side of the front panel. The amplifier is powered up by
the B60. The B60 will power-up momentarily with mute
front panel. It will then quickly turn green signifying nor-
the Bryston B60 please refer to the section on the remote
your loudspeakers. Make certain the left and right speak-
tape deck and other sources to the appropriate left and
The tape loop may be used to insert a surround sound
the toggle switch located on the front panel of the B60.
this manual for further clarity). This feature allows you
to separate the preamplifier section of the B60 from
the power amplifier section by removing the ‘jumpers’.
tors provide for complete separation of the preamplifier
functions available on the front panel of the B60. It also
tion within a multi-channel audio or video system.
The Bryston B60 integrated amplifier comes equipped
with 4 pairs of RCA input connectors, 1 pair of tape loop
with high quality gold plated connectors should be used
with your amplifier to avoid noise and distortion from the
There is a quarter inch stereo (3 conductor) headphone
jack available on the front panel of the Bryston B60 inte-
from the preamplifier section. We recommend the use
You can adjust the volume setting of the headphones
so equipped. The headphones cannot be muted with the
TAPE LOOP:
Tape Outputs:
The “TO TAPE” outputs are selected
tion of other front panel controls.
Tape Inputs:
The “FROM TAPE” (unbalanced RCA)
Tape’ (up) position monitors the recorded signal on
sor. Input sensitivity is 500mv, input impedance is 10K
to the phono inputs on the rear panel. Input impedance
The B60DA / B60RDA models contain an SPDIF
to-analog convertor can handle input sample rates from
VOLUME CONTROL:
TAPE’ outputs). BALANCE: Rotary control adjusts the
CONTROL:
is a
tailored-inflection type
which has very gradual action near the center of rota-
tion allowing fine adjustments to the stereo image.
SWITCH:
for recording or processing, as well as determining
which program is available at the Main outputs. (When
the “TAPE/NORMAL” switch is in “Tape” position,
SWITCH: “
position monitors
position monitors
whichever input is selected at the rotary SELECTOR
switch. “Tape” position provides monitoring of the
input for A/B comparison with the
source. Should an external processor or equalizer be
switch will act as an in/out switch for the external equip-
The Bryston B60 includes a hand
vides for remote volume control
This approach ensures lower dis-
tortion and other noise artifacts
than VCA’s and DAC’s.
the remote control will fully mute
the output from the preamplifier
section. The power LED on the
front panel will turn from green to
The mute function on the remote
The hand held remote unit is battery operated. To
volt battery carefully observing the polarity of both the
We recommend maintaining a direct line-of-sight
to ensure the most efficient operation of the remote fea-
tures.
WEIGHT:
20Hz~20kHz +/- .05dB
SENSITIVITY:
-100dB (Ref. 500mV
THD+N:
SLEW RATE:
SENSITIVITY:
ADDITIONAL SPECIFICATIONS for B60DA/B60RDA DIGITAL INPUTS:
WORD LENGTH:
THD+N:
ADDITIONAL SPECIFICATIONS for B60P/B60RP PHONO INPUTS:
Within less than +/- 0.05dB from 20~20kHz
SENSITIVITY
VARIOUS SPEAKER WIRE TERMINATIONS
AMPLIFIER OUTPUT BINDING POSTS
ture. The warranty includes parts and labour.
first three years of warranty coverage.
The warranty is fully transferable to the original owner and all subsequent owners
This warranty is considered void if the defect, malfunction or failure of the product or
factory authorized service personnel, or failure to fully comply with Bryston operating
This warranty gives you specific legal rights and you may also have other rights which
BRYSTON SERVICE OUTSIDE CANADA & the USA:
www.bryston.ca
info@bryston.ca
BRYSTON SERVICE USA:
BRYSTON SERVICE CANADA
24 STEINWAY BLVD., UNIT 48
All fuses are 5mm x 20mm, time lag type and are accessible only by removing the top cover.
When replacing fuses, disconnect the power cord and all other cables from the B60 before opening the unit!
for 100/120VAC models:
for 220, 230 & 240VAC models:
Loading...