Broan RMDD3604EX User Manual
SPECIFICATION SHEET
MODELS RMDD3004EX,
RMDD3604EX, RMDD4804EX
DOWNDRAFT
For use with external blowers.
Exhaust your cooktop without the use of an overhead hood. Control a powerful external blower from
the cooktop location. Compact design is installed
directly behind cooktop.
FEATURES
HOUSING:
Rugged steel construction
•
Finished with silver paint
•
Space-saving - can be used with most cooktops on the
•
market
30", 36", or 48" widths - Fits standard-size cabinets
•
CHIMNEY ASSEMBLY:
Brushed stainless steel cover - just press button to turn
•
unit "ON"
Chimney rises 9½" when activated - ideal for large pots
•
and pans
Stylish, stainless steel filters with aluminum mesh - easy
•
to remove and dishwasher-safe
Stainless steel chimney front and back - makes cleanup
•
quick and easy
Flush-mounted, infinite rotary speed blower control
•
Heat Sentry adjusts speed of blower to HIGH in case of
•
excess heat
Conveniently located button - press to lower air vent and
•
turn unit "OFF"
OPTIONAL Remote Control (Model RMDDRBK) activates
•
downdraft from alternate location
DUCT CONNECTOR HOUSING:
Rugged steel construction with galvanized finish
•
3¼" x 14" rectangular duct connector (8" round duct using
•
Model 459 transition)
3-position discharge - movable to adjust to floor joists
•
TYPICAL SPECIFICATION
Downdraft blower system shall be Broan Elite Model RMDD3004EX (RMDD3604EX) (RMDD4804EX).
Unit shall be for indoor use only.
Unit to have steel housing with silver paint finish. Air vent to
rise at least 9½" and have a stainless steel front and
for ease of cleaning.
Filters to be stainless steel with aluminum mesh, easy to
remove and dishwasher-safe.
3¼" x 14" duct connector shall be adjustable to accomodate
ductwork from left, right, or below and have 7½" side to side
adjustment.
Unit must accept an optional remote control activation button.
Unit to include Heat Sentry, to adjust blower speed to HIGH
in case of excess heat.
Downdraft system shall operate on 120 VAC and be able to
be plugged into a standard grounded outlet. It will have an
infinite speed blower control.
SPECIFICATIONS
VOLTS HZ AMPS DUCT
120 60 6 3¼" x 14"
back
Broan-NuTone LLC Hartford, Wisconsin www.broan.com 800-558-1711
Broan-NuTone Canada, Inc. Mississauga, Ontario www.broan.ca 877-896-1119
REFERENCE QTY. REMARKS Project
Location
Architect
Engineer
Contractor
Submitted by Date
90M 99043190C
INSTALLATION PLANNING • MODELS RMDD3004EX, RMDD3604EX, RMDD4804EX
DIMENSIONS
NOTE: Dimensions shown are for reference only. Before cutting out
countertop, refer to instructions packed with downdraft and cooktop.
*
*
Dimensioned from top
*
of countertop
TYPICAL INSTALLATION
COUNTER
TOP
COOK TOP
CHIMNEY TOP
DOWNDRAFT
A
COUNTER TOP
COOKTOP
FRONT TO BACK
INSIDE CABINET DEPTH
Refer to the cooktop installation instructions for dimensions of
cooktop, countertop cut-out, and cabinet requirements. The
RMDD3004EX can be installed in most standard 30" wide cabinets, (RMDD3604EX can be installed in most standard 36" wide
cabinets), (RMDD4804EX can be installed in most standard 48"
wide cabinets).
Cooktop depth can vary greatly from one to another. This may
cause the fit of these two appliances to be rather tight.
Pay special attention to the 4 areas of potential interference
highlighted above. A countertop with (A) a raised lip and/or (B)
a backsplash, may not allow enough flat countertop for a proper
installation. The back of the downdraft cut-out will be 1¾" from
the cooktop and 2" of FLAT countertop is needed behind cooktop.
1 3/4 "
2"
B
DOWNDRAFT
DUCTWORK
This downdraft blower system is designed for use with 3¼" x 14"
rectangular ductwork (can be transitioned to 8" or 10" round). The
blower discharge can be positioned in one of 3 directions with
7½" movement side to side.
AIR
VENT
120 VAC
GOUNDED
OUTLET
CABINET
FRONT
GEAR
MOTOR
COVER
BLOWER
BOX
3-1/4" X 14"
DUCT CONNECTOR
ELECTRICAL
The unit has an 18-in. power cord with a 3-pronged plug. Plan to
provide a grounded outlet within reach of this cord.
RIGHT
DISCHARGE
LEFT
DISCHARGE
3¼" x 14" TO
8" RD.
TRANSITION
5 F T.
3¼" X 14"
o
ELBOW
90
DOWN
DISCHARGE
(as shipped)
8" RD.
ELBOW
19 F T.
11 FT.
The system will operate most efficiently when the ductwork does
not exceed 40 feet of equivalent duct. The chart above, shows
equivalent feet of elbows and transitions. The number of feet of
straight 3¼" x 14" or 8" duct plus the equivalent feet of elbows or
transitions to be used should equal 40 feet or less.
The equivalent feet of various roof and wall caps has been taken
into consideration. Do not include them in this calculation.
Loading...