Broan BWP1244SS, BWP1304SS, BWP1364SS, BWP2244SS, BWP2304SS INSTALLATION INSTRUCTIONS AND OPERATION MANUAL

MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •

CHIMNEY
RANGE HOOD

READ AND SAVE THESE INSTRUCTIONS

INTENDED FOR DOMESTIC COOKING ONLY.

!

BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS

Page 1

To register this product visit:

www.broan.com or

www.broan.ca

!

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSON(S) OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the
address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service
panel and lock service disconnecting means to prevent
power from being switch on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service
panel.

3. Installation work and electrical wiring must be done by
qualified personnel in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.

4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as
those published by the National Fire Protection Association
(NFPA), the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE) and the local
code authorities.

5. This product may have sharp edges. Be carefule to avoid
cuts and abrasions during installation or cleaning.

6. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.

7. Ducted fans must always be vented to the outdoors.

8. Do not use this unit with any other solid-state speed control
device.

9. Use only metal ductwork.

10. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when

cooking flaming foods (i.e. Crêpes Suzette, Cherries Jubilee,
Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filters.

d) Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSON(S) IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY,
EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN – You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels –
This could cause a violent steam explosion.

4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you

know how to operate it.
B. The fire is small and contained in the area where it

started.
C. The fire department has been called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or
unbalanced impeller, keep drywall spray, construction dust,
etc. off power unit.

4. Do not use over cooking equipment greater than 60,000
BTU/hr. as the blower motor will shut down intermittently.

5. Your hood motor has a thermal overload which will
automatically shut off the motor if it becomes overheated.
The motor will restart when it cools down. If the motor
continues to shut off and restart, have the hood serviced.

6. The bottom of the hood MUST NOT BE LESS than 24” and
at a maximum of
cooking impurities.

7. Two installers are recommended because of the size of
this hood.

8. To reduce risk of fire and to properly exhaust air, be sure
to duct air outside. Do not exhaust air into spaces within
walls or ceilings or into attics, crawl spaces, or garages.

9. Be careful when installing the decorative flue and hood,
they may have sharp edges.

10. Please read specification label on product for further
information and requirements.

!

36” above cooktop for best capture of

INSTALLER: LEAVE THIS GUIDE WITH THE HOMEOWNER.

HOMEOWNER: OPERATION AND MAINTENANCE INFORMATION ON PAGE 2.

MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •

BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS

Page 2

OPERATION

HC0095

LOW MED. HIGH

BLOWER CONTROLS

The hood is operated using the push buttons on the front panel.
Push the light button to turn the lights on and off.
Push the blower controls to select low, medium, or high blower

speed (for each speed selected, its indicating light will beam).
Press on the current blower speed another time to stop it.

While the blower is activated, press the 5-minute delay button
once (its indicating light will beam) to get the hood running for
5 minutes and then turn off automatically.

When the 5-minute delay is activated, changing the blower
speed will cancel the 5-minute delay function.

To cancel the delay off function before the end of the 5-minute
cycle, press again on delay off push button or select an other
blower speed.

LIGHT

ON/OFF

5-MINUTE

DELAY

CLEANING & MAINTENANCE

Proper maintenance of the Range Hood will assure proper
performance of the unit.

MOTOR

The motor is permanently lubricated and never needs oiling. If
the motor bearings make excessive or unusual noise, replace
the blower with the exact service blower.

GREASE FILTERS

The grease filters should be cleaned frequently. Use a warm
dishwashing detergent solution. Grease filters are dishwasher
safe.
Clean all-metal filters in the dishwasher using a non-phosphate
detergent. Discoloration of the filters may occur if using phosphate
detergents, or as a result of local water conditions - but this will
not affect filter performance. This discoloration is not covered by
the warranty.
Remove grease filters by pulling down on the metal latch tab. This
will disengage the filter from the hood. Tilt the filter downward
and remove.

NON-DUCTED RECIRCULATION FILTERS

The non-ducted recirculation filters should be changed every
6 months. Replace more often if your cooking style generates
extra grease, such as frying and wok cooking. Turn the filter
mounting tabs to remove filter and replace.

STAINLESS STEEL CLEANING

DO:

• Regularly wash with clean cloth or rag soaked with warm water

and mild soap or liquid dish detergent.

• Always clean in the direction of original polish lines.

• Always rinse well with clear water (2 or 3 times) after cleaning.

Wipe dry completely.

• You may also use a specialized household stainless steel

cleaner.

DON’T:

• Use any steel or stainless steel wool or any other scrapers to

remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction residues reach the

hood. During construction/renovation, cover the range hood to
make sure no dust sticks to the stainless steel surface.

Avoid: When choosing a detergent

• Any cleaners that contain bleach will attack stainless steel

• Any products containing: chloride, fluoride, iodide, bromide

will deteriorate surfaces rapidly.

• Any combustible products used for cleaning such as acetone,

alcohol, ether, benzol, etc., are highly explosive and should
never be used close to a range.

MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •

INSTALL THE DUCTWORK

(Ducted Hoods Only)

BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS

Page 3

PREPARE THE HOOD

1. Decide where

ROOF CAP

the ductwork
will run
between the

6"

ROUND DUCT

hood and the
outside.

2. A straight, short
duct run will
allow the hood
to perform most
efficiently.

DECORATIVE

FLUE

HOOD

WALL

CAP

ROUND
ELBOW

3. Long duct
runs, elbows
and transitions
will reduce the

24" MIN. ABOVE

COOKING SURFACE

performance of
the hood. Use as few of them as possible. Larger ducting
may be required for best performance with longer duct runs.

4. Install wall cap or roof cap. Connect round metal ductwork
to cap and work back towards the hood location. Use duct
tape to seal the joints between ductwork sections.

MEASURE THE INSTALLATION

ROOF CAP

6” ROUND DUCT

DECORATIVE FLUE

ROUND ELBOW

HOOD

9-3/4”

WALL CAP

HOOD
MOUNTING
BRACKET

10-5/8 ”
TO CENTER OF
BRACKET HOLES

Unpack hood and check contents. You should receive:
1 - Hood
1 - Decorative Flue Assembly
2 - Damper Flaps
1 - Lower Flue Mounting Bracket
1 - Upper Flue Mounting Bracket
1 - Hood Mounting Bracket
2 - Aluminum Grease Filters for 24" and 30" wide hoods,
(BWP1 series, included packaged in a cardboard box)
3 - Aluminum Grease Filters for 36” wide hood
(BWP1 series, included packaged in a cardboard box)
2 - Hybrid Baffle Filters for 24” and 30” wide hoods,
(BWP2 series, included packaged in a cardboard box)
3 - Hybrid Baffle Filters for 36” wide hood
(BWP2 series, included packaged in a cardboard box)
1 - Installation Manual
1 - Parts Bag containing:
6 - Mounting Screws (no. 8 x 3/8” Pan Head)
7 - Mounting Screws (no. 8 x 1-1/2” Flat Head)
7 - Drywall Anchors
2 - Washers

6 MOUNTING

SCREWS

(no. 8 x 3/8”

Pan Head)

2 WASHERS

DECORATIVE FLUE

7 MOUNTING
SCREWS
(no. 8 x 1½”
Flat Head)

UPPER

FLUE MOUNTING

BRACKET

HOOD

MOUNTING

BRACKET

24” - 36” ABOVE

COOKING SURFACE

3-3/8”

DUCT

CENTER

LINE

The minimum hood distance above cooktop MUST NOT BE
LESS than 24”.

A maximum of 36” above cooktop is highly recommended for
best capture of cooking impurities.

Distances over 36” are at the installer and users discretion;
providing that the ceiling height permits.

DAMPER

FLAPS

LOWER

FLUE MOUNTING

BRACKET

7 DRYWALL

ANCHORS

MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •

BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS

PREPARE THE HOOD (CONT’D)

For ducted installation only:

Install both damper flaps inside the blower exhaust opening,
ensuring the pins are top oriented. See illustration below.

PINS ON TOP

INSTALL THE WIRING

LOCATE
ELECTRICAL
OUTLET
WITHIN THESE
AREAS.
(Verify location
will not interfere
with duct,
mounting
brackets,
and flue.)

4”

Page 4

22”

11 ”

1. GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an electrical

short circuit, grounding reduces the risk of electric shock
by providing an escape wire for the electric current. This
appliance is equipped with a cord having a grounding wire
with a grounding plug. The plug must be plugged into an
outlet that is properly installed and grounded.

NOTE:

A recessed “clock” outlet is recommended.

2. Position the electrical outlet within the space covered by
the decorative flue and where it will not interfere with the
round duct. Make sure the outlet does not interfere with the
mounting bracket fastening area, ductwork, or where the
decorative flue touches the wall.

MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •

BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS

INSTALL THE HOOD MOUNTING BRACKET

WALL STUDS

FRAMING BEHIND

DRYWALL

C

L

Page 5

77⁄8”

19⁄16”

315⁄16”

NOTE:

MOUNTING BRACKET LOCATION
(ABOVE 36” HIGH COOKTOP)

40 5/8” = bottom of hood 30” above cooktop

1. Construct wood wall framing that is flush with
interior surface of wall studs.

Make sure:
a) the framing is centered over installation

location.

b) the height of the framing will allow the

mounting bracket to be secured to the framing
within the dimensions shown.

2. After wall surface is finished, carefully center and
level the hood mounting bracket and secure it
to wall framing with (3) no. 8 x 1½” mounting
screws. Tighten the screws completely.

NOTE: Do not use drywall anchors.

CEILING

HEIGHT

8 FEET

9 FEET

10 FEET

NOTE:
Minimum hood distance above cooktop must not be less than 24”.
Distances over 36” above the cooktop are at the installer’s and user’s discretion - providing that ceiling height and flue length permit.

DUCT

METHOD

DUCTED

NON-DUCTED

DUCTED --- --- --- --- --- --- --- ---

NON-DUCTED --- --- --- --- --- --- --- ---

DUCTED --- --- --- --- --- --- --- ---

NON-DUCTED --- --- --- --- --- --- --- ---

24” 25” 26” 27” 28” 29” 30” 31” 32” 33” 34” 35” 36”

MOUNTING BRACKET LOCATION ABOVE 36” HIGH COOK TOP

34-5/8” 35-5/8” 36-5/8” 37-5/8” 38-5/8” 39-5/8” 40-5/8” 41-5/8” 42-5/8” 43-5/8” 44-5/8”
34-5/8” 35-5/8” 36-5/8” 37-5/8” 38-5/8” 39-5/8” 40-5/8” 41-5/8”

HOOD DISTANCE ABOVE 36” COOK TOP

On 8-ft. ceilings

Hood distance above cooktop is:
Minimum 24”, Maximum 34¾” (for ducted
discharge)
Minimum 24”, Maximum 31” (for non-ducted
discharge)

On 9-ft. ceilings

Hood distance above cooktop is:
Minimum 32”, Maximum 36” (for both ducted and
non-ducted discharge)

On 10-ft. ceilings

Hood distance above cooktop is:
Minimum 32”, Maximum 36” (for both ducted and
non-ducted discharge).

NOTE: 10-ft. ceilings require 10-ft. Flue
Extension, Model FXN58SS for ducted or
non-ducted installations
(purchase separately).

--- ---

--- --- --- --- ---

42-5/8” 43-5/8” 44-5/8”
42-5/8” 43-5/8” 44-5/8”
42-5/8” 43-5/8” 44-5/8”
42-5/8” 43-5/8” 44-5/8”

45-5/8” 46-5/8”
45-5/8” 46-5/8”
45-5/8” 46-5/8”
45-5/8” 46-5/8”

MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •

BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS

INSTALL UPPER FLUE MOUNTING
BRACKET

Page 6

INSTALL THE HOOD

(Horizontally Ducted Hoods Only)

Center of installation

Recommended

distance between

screw holes

Ceiling

Upper flue mounting

1. If a framing member is not present, drill two 5/16” diameter
holes where shown. Insert drywall anchors into the holes.

2. Center the bracket over the hood location and flush with the
ceiling. Make sure that the slots of the upper flue bracket are
at the bottom. Secure the upper flue bracket to the wall using
(2) no. 8 x 1½” mounting screws.

3. Tighten the screws completely. Make sure that the bracket
is tight against the wall.

C

L

4¼”

2⁄8”

Center of

installation

C

L

bracket slots

Ceiling

1”

Ø 5/16” TYP.

Flush with
the ceiling

1. DO NOT REMOVE the protective plastic film covering the
decorative flue and the hood at this time.

2. Lay the back side of the hood flat on a table. Use a piece of
cardboard to avoid damaging the table or the hood.

3. Remove the grease filters by pulling down the metal latch
tab and tilting filters downward to remove.

4. Carefully rotate hood upright.

LOWER FLUE

MOUNTING BRACKET

14¼”

MAX.

5. To make sure there will be adequate clearance between top
of hood and lower flue mounting bracket for ductwork: Elbow
must be located below lower flue mounting bracket.

6. Align the hood and center it above the hood mounting
bracket. Gently lower the hood until it securely engages the
bracket.

INSIDE BACK OF HOOD

MOTOR/BLOWER

ASSEMBLY

SIDE VIEW

HOLES LOCATION

7. With the hood hanging in place, drill through both holes
located in the inside lower back of hood using a 5/16” drill
bit. Insert the included drywall anchors into the drilled holes
(one for each hole). Install (2) washers and (2) no. 8 x 1½”
mounting screws through the hood back and into the drywall
anchors. Verify that the hood is centered and leveled.
Tighten all screws completely.

8. Reinstall grease filters by aligning rear filter tabs with slots
in the hood. Pull down the metal latch tab, push filter into
position and release. Make sure filters are securely engaged
after installation.

Ø 5/16” TYP.

MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •

BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS

Page 7

6” ROUND
DUCT ELBOW

9. Measure and install 6” round steel ductwork to roof cap or
wall cap and 90o elbow over the blower exhaust opening on
top of hood. Use duct tape to make all joints secure and air
tight.

10. Plug hood power cord into the outlet.

LOWER FLUE MOUNTING BRACKET

LOWER

FLUE

NOTE: 10-ft. ceilings require 10-ft. Flue Extension Model
FXN58SS (purchase separately). Discard the upper flue
supplied with your hood and replace it with the Model
FXN58SS flue extension.

11. Remove the upper flue from inside the lower flue. Install
the lower flue bracket to the lower flue using (2) flue
bracket screws (no. 8 x 3/8”). Make sure that the bracket is
positioned inside of the lower flue flanges - with the slots on
top. Carefully replace the upper flue inside the lower flue.
Remove protective plastic film covering the lower flue only.

12. Carefully place both flues into the recessed area of hood
top. Slightly push aside the upper flue to avoid any
damage while installing the lower flue to the hood top using
(2) no. 8 x 3/8” screws through the lower flue side slots.

UPPER FLUE MOUNTING BRACKET

UPPER

FLUE

13. Slide the upper flue upward until it is aligned with its upper
flue mounting bracket. The bracket should be inside the flue.
Secure the upper flue to the upper flue mounting bracket
using (2) no. 8 x 3/8” mounting screws.

14. Remove protective plastic film covering the upper flue and
the hood.

INSTALL THE HOOD

(Vertically Ducted Hoods Only)

1. DO NOT REMOVE the protective plastic film covering the
decorative flue and the hood at this time.

2. Lay the back side of the hood flat on a table. Use a piece
of cardboard to avoid damaging the table or the hood.

3. Remove the grease filters by pulling down the metal latch
tab and tilting filters downward to remove.

4. Carefully rotate hood upright.

LOWER FLUE MOUNTING BRACKET

LOWER

FLUE

NOTE: 10-ft. ceilings require 10-ft. Flue Extension Model
FXN58SS (purchase separately). Discard the upper flue
supplied with your hood and replace it with the Model
FXN58SS flue extension.

5. Remove the upper flue from inside the lower flue. Install
the lower flue bracket to the lower flue using (2) flue
bracket screws (no. 8 x 3/8”). Make sure that the bracket is
positioned inside of the lower flue flanges - with the slots on
top. Carefully replace the upper flue inside the lower flue.
Remove protective plastic film covering the lower flue only.

6. Carefully place both flues into the recessed area of hood top.

MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •

BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS

Page 8

6” ROUND

STEEL DUCT

DUCT LENGTH

DECORATIVE

FLUE

7. Measure and install 6” round steel ductwork to the blower
exhaust opening on top of hood. Use duct tape to make all
joints secure and air tight.

8. Hold hood up close to wall mounting location and plug
power cord into wall outlet.

9. Align the hood and center it above the hood mounting
bracket. Make sure ductwork on hood lines up and attaches
to ductwork in ceiling. Gently lower the hood until it securely
engages the bracket.

10. Use duct tape to make all joints secure and air tight.

INSIDE BACK OF HOOD

UPPER FLUE MOUNTING BRACKET

UPPER

FLUE

14. Slide the upper flue upward until it is aligned with its upper
flue mounting bracket. The bracket should be inside the flue.
Secure the upper flue to the upper flue mounting bracket
using (2) no. 8 x 3/8” mounting screws.

15. Remove protective plastic film covering the upper flue and
the hood.

INSTALL THE HOOD

(Non-Ducted Hoods Only)

MOTOR/BLOWER

ASSEMBLY

SIDE VIEW

HOLES LOCATION

11. With the hood hanging in place, drill through both holes
located in the inside lower back of hood using a 5/16” drill
bit. Insert the included drywall anchors into the drilled holes
(one for each hole). Install (2) washers and (2) no. 8 x 1½”
mounting screws through the hood back and into the drywall
anchors. Verify that the hood is centered and leveled. Tighten
all screws completely.

12. Reinstall grease filters by aligning rear filter tabs with slots
in the hood. Pull down the metal latch tab, push filter into
position and release. Make sure filters are securely engaged
after installation.

13. Slightly push aside the upper flue to avoid any damage while
installing the lower flue to the hood top using (2) no. 8 x 3/8”
screws through the lower flue side slots.

Ø 5/16” TYP.

NON-DUCT KIT MODEL ARKBWP CONTENTS

NON-DUCTED

RECIRCULATION

FILTERS

NON-DUCT

PLENUM

NON-DUCT PLENUM

COLLAR

NOTE: Non-ducted installations require Non-Duct Kit,
model ARKBWP (purchase separately).

1. CAUTION: Use only flexible duct provided.

2. Do not remove the protective plastic film covering the
decorative flue and the hood at this time.

3. Lay the back side of the hood flat on a table. Use a piece
of cardboard to avoid damaging the table or the hood.

8 MOUNTING
SCREWS
(ST4 x 8
Round Head)

2 TIE

WRAPS

FLEXIBLE DUCT

MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •

BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS

4. Remove the
grease filters
by pulling
down the
metal latch
tab and
tilting filters
downward to
remove.

5. Attach non-duct collar to non-duct plenum using
(4) no. 8 x 3/8” pan head screws.

6. Measure
distance “A”.
This will be the
length of the
extended flex
duct.

7. Attach
aluminum
flexible duct to
the damper /
duct connector
with a tie wrap.

8. Attach flexible
duct to non-duct
plenum collar
and secure with
tie wrap. Tape
all joints with
duct tape.

NOTE: 10-ft. ceilings require 10-ft. Flue Extension Model
FXN58SS (purchase separately). Discard the upper flue
supplied with your hood and replace it with the Model
FXN58SS flue extension.

NON-DUCT PLENUM

NON-DUCT COLLAR

6” ALUMINUM

FLEX DUCT

DUCT CONNECTOR
(without flaps)

LOWER FLUE MOUNTING BRACKET

3-5/8”

A

Page 9

12. Hold hood up close to wall mounting location and plug
power cord into wall outlet.

13. Align the hood and center it above the hood mounting bracket.
Gently lower the hood until it securely engages the bracket.

INSIDE BACK OF HOOD

MOTOR/BLOWER

ASSEMBLY

SIDE VIEW

HOLE LOCATIONS

14. With the hood hanging in place, drill through both holes
located in the inside lower back of hood using a 5/16” drill
bit. Insert the included drywall anchors into the drilled holes
(one for each hole). Install (2) washers and (2) no. 8 x 1½”
mounting screws through the back of the hood and into
the drywall anchors. Verify that the hood is centered and
leveled. Tighten all screws completely.

15. Attach (2)
two non-duct
recirculation
filters to sides
of blower by
aligning key lock
slot and rotating
until filters lock
into place.

For replacement non-duct recirculation filters - purchase

S99010494 (set of 2 filters).

16. Reinstall grease filters by aligning rear filter tabs with
slots in the hood. Pull down the metal latch tab, push filter
into position and release. Make sure filters are securely
engaged after installation.

Ø 5/16” TYP.

LOWER

FLUE

9. Remove the upper flue from inside the lower flue. Install
the lower flue bracket to the lower flue using (2) flue
bracket screws (no. 8 x 3/8”). Make sure that the bracket is
positioned inside of the lower flue flanges - with the slots on
top. Carefully replace the upper flue inside the lower flue.
Remove protective plastic film covering the lower flue only.

10. Carefully place both flues into the recessed area of hood
top. Slightly push aside the upper flue to avoid any damage
while installing the lower flue to the hood top by using
(2) no. 8 x 3/8” screws through the lower flue side slots.

11. Attach non-duct plenum with collar to upper flue using
(4) no. 8 x 3/8” pan head screws.

UPPER FLUE MOUNTING BRACKET

UPPER

FLUE

17. Slide up the upper flue upward until it is aligned with its
upper flue mounting bracket. The bracket should be inside
the flue. Secure the upper flue to the upper flue mounting
bracket using (2) no. 8 x 3/8” mounting screws.

18. Remove protective plastic film covering the flue and the hood.

MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •

BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS

SERVICE PARTS

BWP1 Series

KEY PART NO. DESCRIPTION QTY.

1 S99526972 Decorative Upper and Lower Flues 1
2 S99010499 Damper Flap 2
3 S99010484 Control Assembly 1
4 S99010492 400 CFM Motor / Blower Assembly 1
5 S99529088 Plastic Box of PCB 1
6 S99010495 Main PCB 1
7 S99010490 Capacitor 25 μF 1
8 S99529091 LED Module 5.5 W 2
9 S99010489 Aluminum Grease Filters (pair) BWP1244SS 1
S97018027 Aluminum Grease Filters (pair) BWP1304SS 1

S97018028 Aluminum Grease Filters (3 per hood) BWP1364SS 1
10 S99528929 Mounting Brackets (set of 3) 1
S99010500 Parts Bag (not shown) 1
S99010494 Non-Duct Recirculation Filters (pair)(not shown) * 1
S99526992 Non-Duct Plenum Assembly (not shown) * 1
S99526984 6” Dia. Expand. Flex. Aluminum Duct (not shown) * 1

* Included with optional Non-Duct Kit - Model ARKBWP.
Order service parts by Part No. - not by Key No.

Page 10

1



2

3

4

BWP2 Series

KEY PART NO. DESCRIPTION QTY.

1 S99526972 Decorative Upper and Lower Flues 1
2 S99010499 Damper Flap 2
3 S99010484 Control Assembly 1
4 S99010492 400 CFM Motor / Blower Assembly
(BWP2244SS, BWP2304SS, BWP2364SS) 1
S99010493 600 CFM Motor / Blower Assembly
(BWP2306SS, BWP2366SS) 1
5 S99529088 Plastic Box of PCB 1
6 S99010495 Main PCB 1
7 S99010490 Capacitor 25 μF
(BWP2244SS, BWP2304SS, BWP2364SS) 1
S99010491 Capacitor 30 μF (BWP2306SS, BWP2366SS) 1
8 S99529091 LED Module 5.5 W 2
9 S99010486 Hybrid Baffle Filters (pair) (BWP2244SS) 1
S99010487 Hybrid Baffle Filters (pair)
(BWP2304SS, BWP2306SS) 1

S99010488 Hybrid Baffle Filters (3 per hood)
(BWP2364SS, BWP2366SS) 1
10 S99528929 Mounting Brackets (set of 3) 1
S99010500 Parts Bag (not shown) 1
S99010494 Non-Duct Recirculation Filters (pair)(not shown) * 1
S99526992 Non-Duct Plenum Assembly (not shown) * 1
S99526984 6” Dia. Expand. Flex. Aluminum Duct (not shown) * 1

* Included with optional Non-Duct Kit - Model ARKBWP.
Order service parts by Part No. - not by Key No.

5
6

7
8

9

Replacement parts can be ordered on our website:

www.broan.com for US customers only

R

EPLACEMENT PARTS AND REPAIRS

In order to ensure your unit remains in good working condition, you
must use Broan-NuTone LLC or Venmar Ventilation ULC genuine
replacement parts only. Broan-NuTone LLC or Venmar Ventilation
ULC genuine replacement parts are specially designed for each unit
and are manufactured to comply with all the applicable certification
standards and maintain a high standard of safety. Any third party
replacement part used may cause serious damage and drastically
reduce the performance level of your unit, which will result in
premature failing. Broan-NuTone LLC and Venmar Ventilation ULC
recommend to contact a certified service depot for all replacement
parts and repairs.

WARRANTY

MODELS BWP1244SS • BWP1304SS • BWP1364SS • BWP2244SS •

BWP2304SS • BWP2364SS • BWP2306SS • BWP2366SS

Page 11

Warranty Period and Exclusions: Broan-NuTone LLC and Venmar Ventilation ULC (either being the “Company”) warrants to the original consumer
purchaser of its product (“you”) that the product (the “Product”) will be free from material defects in the Product or its workmanship for a period of
one(1)year from the date of original purchase (or such longer period as may be required by applicable law). The limited warranty period for any replacement
parts provided by the Company and for any Products repaired or replaced under this limited warranty shall be the remainder of the original warranty period
(or such longer period as may be required by applicable law).
This warranty does not cover fluorescent lamp starters, tubes, halogen and incandescent bulbs, fuses, filters, ducts, roof caps, wall caps and other
accessories for ducting that may be purchased separately and installed with the Product. This warranty also does not cover (a) normal maintenance and
service, (b) normal wear and tear, (c) any Products or parts which have been subject to misuse, abuse, abnormal usage, negligence, accident, improper
or insufficient maintenance, storage or repair (other than repair by the Company), (d) damage caused by faulty installation, or installation or use contrary to
recommendations or instructions, (e) any Product that has been moved from its original point of installation, (f) damage caused by environmental or natural
elements, (g) damage in transit, (h) natural wear of finish, (i) Products in commercial or nonresidential use, or (j) damage caused by fire, flood or other act
of God or (k) Products with altered, defaced or removed serial numbers. This warranty covers only Products sold to original consumers in the United States
and Canada by the Company or its U.S. and Canadian distributors authorized by the Company.
This warranty supersedes all prior warranties and, subject to applicable law, is not transferable from the original consumer purchaser.

No Other Warranties: This Limited Warranty contains the Company’s sole obligation and your sole remedy for defective products. The foregoing warranties
are exclusive and in lieu of any other warranties and conditions, express or implied. THE COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS

WARRANTIES AND CONDITIONS, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES AND CONDITIONS IMPLIED BY LAW, INCLUDING
WITHOUT LIMITATION THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent that applicable law prohibits the

exclusion of implied warranties or conditions, the duration of any applicable implied warranty or condition is limited to the period specified for the express
warranty above. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Any oral or
written description of the Product is for the sole purpose of identifying it and shall not be construed as an express warranty.
Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and valid under applicable law, but if
any provision is held to be prohibited or invalid, such provision shall be ineffective only to the extent of such prohibition or invalidity, without invalidating the
remainder of such provision or the other remaining provisions of the Limited Warranty.

Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or repair or replace, without charge,
any Product or part thereof, to the extent the Company finds it to be covered by and in breach of this limited warranty under normal use and service. The
Company will ship the repaired or replaced Product or replacement parts to you at no charge. You are responsible for all costs for removal, reinstallation
and shipping, insurance or other freight charges incurred in the shipment of the Product or part to the Company. If you must send the Product or part to the
Company, as instructed by the Company, you must properly pack the Product or part—the Company is not responsible for damage in transit. The Company
reserves the right to utilize reconditioned, refurbished, repaired or remanufactured Products or parts in the warranty repair or replacement process. Such
Products and parts will be comparable in function and performance to an original Product or part and warranted for the remainder of the original warranty
period (or such longer period as may be required by applicable law).
Company reserves the right, in its sole discretion, to refund the money actually paid by you for the Product in lieu of repair or replacement. If the Product
or component is no longer available, replacement may be made with a similar product of equal or greater value, at Company’s sole discretion. This is your
sole and exclusive remedy for breach of this limited warranty.

Exclusion of Damages: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR, REPLACE OR REFUND, AT THE
COMPANY’S OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY AND THE COMPANY’S SOLE AND
EXCLUSIVE OBLIGATION. THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES
ARISING OUT OF OR IN CONNECTION WITH THE PRODUCT, ITS USE OR PERFORMANCE. Incidental damages include but are not limited to such

damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was
damaged if the Product does not work properly.

THE COMPANY SHALL NOT BE LIABLE TO YOU, OR TO ANYONE CLAIMING UNDER YOU, FOR ANY OTHER OBLIGATIONS OR LIABILITIES,
INCLUDING, BUT NOT LIMITED TO, OBLIGATIONS OR LIABILITIES ARISING OUT OF BREACH OF CONTRACT OR WARRANTY, NEGLIGENCE
OR OTHER TORT OR ANY THEORY OF STRICT LIABILITY, WITH RESPECT TO THE PRODUCT OR THE COMPANY’S ACTS OR OMISSIONS OR
OTHERWISE.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from jurisdiction to jurisdiction. The disclaimers, exclusions,
and limitations of liability under this warranty will not apply to the extent prohibited by applicable law.
This warranty covers only replacement or repair of defective Products or parts thereof at the Company’s main facility and does not include the cost of field
service travel and living expenses.
Any assistance the Company provides to or procures for you outside the terms, limitations or exclusions of this limited warrant will not constitute a waiver
of such terms, limitations or exclusions, nor will such assistance extend or revive the warranty.
The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective Product, except for those incurred with the
Company’s prior written permission.

How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify the Company at the address or telephone number stated below within
seven (7) days of discovering the covered defect, (b) give the model number and part identification and (c) describe the nature of any defect in the Product
or part. At the time of requesting warranty service, you must present evidence of the original purchase date. If you cannot provide a copy of the original
written limited warranty, then the terms of the Company’s most current written limited warranty for your particular product wil
limited written warranties for the Company’s products can be found at www.broan.com and www.broan.ca.
Broan-NuTone LLC 926 West State Street, Hartford, WI 53027 www.broan.com 800-637-1453
Venmar Ventilation ULC, 550 Lemire Blvd., Drummondville, Québec, Canada J2C 7W9 www.broan.ca 1-877-896-1119

Limited Warranty

l control. The most current

99529080C