Broan 52WH254DP, 52WH304PF, 52WH254DPF, 52WH304DP, 52WH304DPF Installation Instructions Manual

MODEL: 52WH254DP, 52WH254DPF,

52WH304P, 52WH304PF,
52WH304DP, 52WH304DPF

RECESSED MOUNTED,
STEEL MEDICINE CABINETS

INSTALLATION INSTRUCTIONS

MODEL WALL OPENING OVERALL SIZE

NO. W H D W H D
52WH254DP 191/424 4 20 25 5
52WH254DPF 191/424 4 20 25 5
52WH304P 231/429 4 24 30 5
52WH304PF 231/429 4 24 30 5
52WH304DP 231/429 4 24 30 5
52WH304DPF 231/429 4 24 30 5

1. Carefully remove all packing material. Place
hardware packages, shelves and door aside until
needed. Hardware and shelves are located in the
fillers identified by “Hardware enclosed” tape.

2. Determine desired location of cabinet on wall.
Mark wall to show wall opening size (see
dimension chart). Generally, the recommended
height to the center of the cabinet is 64” from the
floor. (Fig. 1)

3. CAUTION: Wall studs, plumbing or electrical lines
that interfere must be removed or relocated. Cut
wall opening, being careful not to damage the
surrounding wall surface. Insert framing to
support all plaster board edges.

Fig. 1

Insert screw
through clear
plastic base

4. Prepare the mounting screws by placing the
screws into the clear plastic bases. (Fig. 2)

5. Note: For ease of installation, an additional person is
recommended. Insert cabinet into wall opening.
(Fig.3) Ensure the cabinet is plumb and level. If
necessary use a carpenter’s level and shim corners of
cabinet. Secure to wall studs through the four (4)
mounting holes inside cabinet, using the screws that
have been placed into the plastic bases. (Fig. 4) Do
not over tighten the mounting screws as the body
side wall may bend and prevent proper shelf
installation. Only tighten screws until they are
flush with the body.

6. Snap the screw covers over the screw bases.
(Fig.5)

Fig. 2

Fig. 5

Snap on Cover

Screw

Cover

Fig. 3

Wall
Opening

Cabinet
Body

Base

Fig. 4

Mounting
Screws

Mounting
screw into
mounting
hole

1. Remove hinges and screws from hardware
bag. Mount hinge unit on door as shown in
Fig. 6 and Fig. 7 securing with screws
provided.

2. Install the door by inserting door side of the
hinge into the bracket on the body as shown;

A) 125 degree hinge

Insert door side of clip hinge as shown
in Fig. 8

B) 170 degree hinge

Insert door side of clip hinge as shown
in Fig. 9

3. Check door for proper alignment. If the door
needs to be adjusted please refer to the
adjustment procedures in Fig. 10 and
Fig. 11. Door edges should be aligned with
the edges of the body and should fit evenly
to the face of the body.

4. 125 degree hinge only: Snap on hinge
cover plate. (Fig. 12)

Fig. 6

Fig. 7

125 Degree Hinge
Mounted to Door

170 Degree Hinge
Mounted to Door

Fig. 8

125 Degree Hinge
mounted to Cabinet

Press down
on hinge until
it clips in place

Fig. 10

125 Degree Hinge

This screw
for depth
adjustment

This screw
for left and right
adjustment

Hook bottom of
hinge into place
on the bracket

This screw for
up and down
adjustment

Fig. 11

170 Degree Hinge

This screw
for depth
adjustments

This screw
for left and right
adjustments

Fig. 9

This screw for
up and down
adjustments

170 Degree Hinge
Mounted to Cabinet

Press down
on hinge until it
clips in place

Hook bottom of
hinge into place
on the bracket

Fig. 12

Hinge Cover

2