CREATISTA
by Nespresso
B16
CREATISTA
MY MACHINE
EN
EN
User manual 3
1
•
EN
Nespresso Breville Creatista
Congratulations on your purchase of the Nespresso Breville Creatista, the machine that allows you to make cafe quality
milk coffees.
2
EN
Packaging Content
❶ Creatista Coffee Machine
Creatista
USER MANUAL
Nespresso is an exclusive system creating the perfect Espresso, time after time.
Each parameter has been calculated with great precision to ensure that all the
aromas from each capsule can be extracted, to give the coffee body and create
an exceptionally thick and smooth crema.
CAUTION: When you see this sign, please refer to the
MAX
MIN
Welcome
❷ Tasting Box of Nespresso
Capsules
❸ Milk Jug
❹ Nespresso Welcome Brochure
important safeguards to avoid possible harm and damage.
INFORMATION: when you see this sign, please take note of the advice for
the correct and safe usage of your coffee machine.
BNE600 Specifications/
techniques
❺ User Manual
CREATISTA
MY MACHINE
1 x Water Hardness Test Strip, in the User Manual
3
220-240 V, 50 Hz, 1300-1600 W
19 bar / 1.9 MPa
max
~5.2 kg / 11.4 lbs
1.5 L / 50 oz
17.0 cm 30.9 cm 40.9 cm
6.7 in 12.2 in 16.1 in
Content
Nespresso Creatista 2
Packaging Content 3
Creatista 3
Specifications 3
Safety Precautions 5-7
Machine Overview 8
First Use 9-10
Navigation 11
Regular Coffee Preparation 12
Milk Coffee Preparation - Single Cup 13-14
Milk Coffee Preparation - Two Cup 15-17
Latte Macchiato Preparation 18-19
Adjusting Regular Coffee Drinks 20
Adjusting Milk Coffee Drinks 21
Reset to Factory Settings 22
Emptying the System 22
Energy Saving 23
Daily Cleaning 23-24
Steam Wand Cleaning Procedure 24
Descaling 25
Water Hardness 26
Troubleshooting 27
Troubleshooting Milk Froth Preparation 28
Contact Nespresso Club 29
Disposal and Environmental Protection 29
Limited Guarantee 30
EN
4
EN EN
Safety Precautions
•
CAUTION: the safety
precautions are part of
the appliance. Read them
carefully before using your
new appliance for the first
time. Keep them in a place
where you can find and
refer to them later on.
CAUTION: when you see
this sign, please refer to
the safety precautions to
avoid possible harm and
damage.
INFORMATION: when
you see this sign, please
take note of the advice for
the correct and safe usage
of your appliance.
•
The appliance is intended to
prepare beverages according
to these instructions.
5
Do not use the appliance
for anything other than its
intended use.
•
This appliance has been
designed for indoor and
non-extreme temperature
conditions use only.
•
Protect the appliance
from direct sunlight effect,
prolonged water splash and
humidity.
•
This is a household
appliance only. It is not
intended to be used in: staff
kitchen areas in shops,
offices and other working
environments; farm houses;
by clients in hotels, motels
and other residential type
environments; bed and
breakfast type environments.
•
This appliance may be
used by children of at least
8 years of age, as long
as they are supervised
and have been given
instructions about using the
appliance safely and are
fully aware of the dangers
involved. Cleaning and user
maintenance shall not be
made by children unless they
are older than 8 and they are
supervised by an adult.
•
Keep the appliance and its
cord out of reach of children
under 8 years of age.
•
This appliance may be used
by persons with reduced
physical, sensory or mental
capabilities, or whose
experience or knowledge
is not sufficient, provided
they are supervised or have
received instruction to use
the appliance safely and
understand the dangers.
•
Children shall not use the
device as a toy.
•
The manufacturer accepts
no responsibility and the
warranty will not apply
for any commercial use,
inappropriate handling or
use of the appliance, any
damage resulting from use
for other purposes, faulty
operation, non-professionals
repair or failure to comply
with the instructions.
Avoid risk of fatal
electric shock and fire.
•
In case of an emergency:
immediately remove the plug
from the power socket.
•
Only plug the appliance into
suitable, easily accessible,
earthed mains connections.
Make sure that the voltage
of the power source is the
same as that specified on
the rating plate. The use
of an incorrect connection
voids the warranty.
Safety Precautions
ENEN
The appliance must
only be connected after
installation.
•
Do not pull the cord over
sharp edges, clamp it or
allow it to hang down.
•
Keep the cord away from
heat and damp.
•
If the supply cord is
damaged, it must
be replaced by the
manufacturer, its service
agent or similarly qualified
persons, in order to avoid all
risks.
•
If the cord is damaged, do
not operate the appliance;
return the appliance to
the Nespresso Club or to
a Nespresso authorised
representative.
•
If an extension cord is
required, use only an
earthed cord with a
conductor cross-section of
at least 1.5 mm2 or matching
input power.
•
To avoid hazardous damage,
never place the appliance on
or beside hot surfaces such
as radiators, stoves, ovens,
gas burners, open flame, or
similar.
•
Always place it on a
horizontal, stable and even
surface. The surface must
be resistant to heat and
fluids, like water, coffee,
descaler or similar liquids.
•
Disconnect the appliance
from the mains when not
in use for a long period.
Disconnect by pulling out the
plug and not by pulling the
cord itself or the cord may
become damaged.
•
Before cleaning and
servicing, remove the plug
from the mains socket and
let the appliance cool down.
•
Never touch the cord with
wet hands.
•
Never immerse the appliance
or part of it in water or other
liquid.
•
Never put the appliance or
part of it in a dishwasher.
•
Electricity and water together
is dangerous and can lead to
fatal electrical shocks.
•
Do not open the appliance.
Hazardous voltage inside!
•
Do not put anything into any
openings. Doing so may
cause fire or electrical shock!
Avoid possible harm
when operating the
appliance.
•
Never leave the appliance
unattended during operation.
•
Do not use the appliance
if it is damaged or not
operating perfectly.
Immediately remove the
plug from the power socket.
Contact the Nespresso
Club or Nespresso
authorised representative
for examination, repair or
adjustment.
•
A damaged appliance can
cause electrical shocks,
burns and fire.
•
Always completely close
the slider and never open it
during operation. Scalding
may occur.
•
Do not put fingers under
coffee outlet, risk of scalding.
•
Do not put fingers into
capsule compartment or the
capsule shaft. Danger of
injury!
•
Water could flow around a
capsule when not perforated
by the blades and damage
the appliance.
•
Never use a damaged or
deformed capsule. If a
6
EN EN
Safety Precautions
capsule is blocked in the
capsule compartment, turn
the machine off and unplug it
before any operation. Call the
Nespresso Club or Nespresso
authorised representative.
•
Fill the water tank only with
fresh and potable water.
•
Empty water tank if the
appliance will not be used for
an extended time (holidays,
etc.).
•
Replace water in water tank
when the appliance is not
operated for a weekend or a
similar period of time.
•
Do not use the appliance
without the drip tray and drip
grid to avoid spilling any liquid
on surrounding surfaces.
•
Do not use any strong
cleaning agent or solvent
cleaner. Use a damp cloth
and mild cleaning agent
to clean the surface of the
7
appliance.
•
To clean machine, use only
clean cleaning tools.
•
When unpacking the
machine, remove the plastic
film and dispose.
•
This appliance is designed for
Nespresso coffee capsules
available exclusively through
the Nespresso Club or
your Nespresso authorised
representative.
•
All Nespresso appliances
pass stringent controls.
Reliability tests under
practical conditions are
performed randomly on
selected units. This can show
traces of any previous use.
•
Nespresso reserves the
right to change instructions
without prior notice.
•
This machine contains
magnets.
Descaling
•
Nespresso descaling agent,
when used correctly, helps
ensure the proper functioning
of your machine over its
lifetime and that your coffee
experience is as perfect as
the first day.
SAVE THESE
INSTRUCTIONS
Pass them on to any
subsequent user.
This instruction manual
is also available as a PDF
at nespresso.com
EN
EN
Machine Overview
Color display
SELECT dial
START | CANCEL button
Lever for capsule insertion
Capsule container
Pop out cup support
Removable drip grid
Removable drip tray
with full indicator
EN
Water tank & lid
Removable pin cleaning tool
Easy clean steam
wand
Milk jug temperature
sensor
Milk jug
Press the START|CANCEL
button to S tart or Can cel
an operation or to go back
Rotate the S ELECT dial
to navigate left or right
to select your drink
Press the SELECT dial to
Adjust Espresso Volume,
Milk Temperature or
Milk Froth
8
EN
First Use
Read the important safeguards first to avoid risks of fatal electrical shock and fire.
❶ Rinse the water tank
before filling it with
potable water.
❹ Turn the machine ON by pressing the START|CANCEL
button. Heating up takes approximately 10 seconds.
❷ Place the water tank, insert
the drip tray and the capsule
container in position. For your
safety, operate the machine
only with drip tray and
capsule container in position.
❺ Rotate the SELECT dial to set your
❸ Plug the machine into
the power outlet.
language. Press SELECT to confirm.
9
First Use
EN
< 1 minute
❻ Setting your water hardness, dip the Water
Hardness Test Strip in and out the water tank.
Wait 1 minute. Set the water hardness by
rotating the SELECT dial according to the results
on the Test Strip. Press SELECT to confirm.
For further information refer to page 26.
❽ Follow the Quick Start Tutorial.
❼ Follow the on-screen prompts to rinse
& prepare your machine for use.
First use is to rinse the machine & prime the heating system.
❾ To turn OFF your machine, press and
hold the START/CANCEL dial for 2 seconds
until machine is off.
10
Coffee Volume
Milk Temp
Ideal
Milk Temp
Ideal
Cappuccino
Café Latte
Cappuccino
Cappuccino
Cappuccino
EN
Navigation
❶ Rotate the SELECT dial
❸ Press START|CANCEL
to make a coffee with
the current settings.
to select your coffee
❷ Display shows current drink settings,
Coffee Volume, Milk Temperature,
Milk Texture.
❹ Press the SELECT
dial to adjust the
current settings.
Refer page 20 & 21.
11
Regular Coffee Preparation
EN
❶ Fill the water tank
with potable water.
❹ Lift the Lever, insert a capsule and close the lever.
Rotate SELECT dial to select your coffee
Ristretto (25ml / 0.85 oz)
Espresso (40 ml / 1.35 oz)
Lungo (110 ml / 3.7 oz)
Press START|CANCEL button to extract
To ensure hygienic conditions, it is highly
recommended to not reuse a used capsule.
❷ Turn the machine ON by
pressing the START|CANCEL
button. Heating up takes
approximately 10 seconds.
❺ Preparation will
stop automatically.
Lift the Lever to
eject the capsule.
❸ Place a cup under the
coffee outlet. Use the cup
support if required. PUSH
the cup support to unlock.
❻ To stop the coffee flow
press the START|CANCEL
button.
12
EN
Milk Coffee Preparation - Single Cup
Only use the milk jug provided.
❶ Fill the water tank
with fresh potable
water.
MAX
MIN
CAUTION: Do not fill milk jug above
the maximum level marked on the
inside & outside of the jug.
❹ Fill the milk jug with enough
fresh cold milk. Minimum and
maximum levels are marked
on the inside and outside of
the milk jug.
TIP: For optimal milk froth, use pasteurised whole or semi skimmed milk at refrigerated temperature (about 4-6 °C / 39-43 °F ).
❷ To accommodate smaller
cups, use the cup support.
PUSH the cup support to
unlock.
❺ Lift the steam wand
& position in the centre
of the milk jug.
❸ Rotate the SELECT dial
to select your drink.
❻ Ensure the milk jug
is making contact
with the temperature
sensor located in the
drip tray.
13
Milk Coffee Preparation - Single Cup
EN
❼ Lift the Lever &
insert your capsule.
❿ When milk frothing is
complete, lift the steam wand,
wipe with a clean damp cloth.
❽ Press the START|CANCEL
button to start the
espresso extraction.
Allow steam wand to return
to its down position & it will
auto purge to rinse itself.
❾ When the espresso
extraction is complete,
press START|CANCEL to
begin milk frothing.
Pour milk into the espresso
to finish your drink.
14
EN
Milk Coffee Preparation - Two Cups
Only use the milk jug provided.
❶ Fill the water tank
with fresh potable
water.
❹ Lift the Lever &
insert your capsule.
TIP: For optimal milk froth, use pasteurised whole or semi skimmed milk at refrigerated temperature (about 4-6 °C / 39-43 °F ).
❷ To accommodate smaller
cups, use the cup support.
PUSH the cup support to
unlock.
❺ Press the START|CANCEL
button to start the espresso
extraction.
MAX
MIN
CAUTION: Do not fill milk jug above
the maximum level marked on the
inside & outside of the jug.
❸ Rotate the SELECT dial
to select your drink.
Fill the milk jug with enough
fresh cold milk for 2 drinks.
Maximum level is marked on
the inside and outside of the
milk jug. Do not overfill.
15
Milk Coffee Preparation - Two Cups
EN
Lift the steam wand
& position in the centre
of the milk jug and
press START|CANCEL
to begin milk frothing.
Allow steam wand to return
to its down position & it will
auto purge to rinse itself.
Ensure the milk jug is
making contact with
the temperature sensor
located in the drip tray.
Place your second cup
under the coffee spout.
When milk frothing is
complete, lift the steam
wand, wipe with a clean
damp cloth.
Lift the Lever & insert
your capsule.
16
EN
Milk Coffee Preparation - Two Cups
Press the START|CANCEL
button to start the espresso
extraction.
Pour milk into the espresso
to finish your drinks.
17
Latte Macchiato Preparation
EN
❶ Fill the water tank
with fresh potable
water.
MAX
MIN
CAUTION: Do not fill milk jug above
the maximum level marked on the
inside & outside of the jug.
Fill the milk jug
to the marked
maximum level
with fresh cold milk
❷ To accommodate a Latte
Macchiato glass, push the
cup support in until it locks.
❺ Lift the steam wand &
position in the centre of
the milk jug and press
START|CANCEL to begin
milk frothing.
❸ Rotate the SELECT dial
to select your drink.
Ensure the milk jug is
making contact with
the temperature sensor
located in the drip tray.
18
EN
Latte Macchiato Preparation
When milk frothing is
complete, lift the steam
wand, wipe with a clean
damp cloth.
Lift the Lever & insert
your capsule.
Allow steam wand to return
to its down position & it will
auto purge to rinse itself.
Press the START|CANCEL button
to start the espresso extraction.
Pour milk into the Latte
Macchiato glass and place
under the coffee spout.
19
Adjusting Regular Coffee Drinks
EN
Rotate the SELECT dial
to the drink.
Press SELECT dial to save &
exit or press START|CANCEL
to exit without saving.
Press the SELECT dial to
adjust the coffee volume.
Any coffee can be programmed.
1. Ristretto: from 25 to 60 ml / 0.85-2 oz.
2. Espresso: from 25 to 60 ml / 0.85-2 oz.
3. Lungo: from 70 to 150 ml / 2.37 to 5 oz.
Default coffee volumes listed on page 12.
Rotate the SELECT dial to
adjust the coffee volume.
The suggested volume is
marked with a dotted line.
20
EN
Adjusting Milk Coffee Drinks
This machine is optimized for pasteurised whole or semi skimmed milk. Milk Temperature and Milk Froth may be adjusted to suit different milk types.
Rotate the SELECT
dial to the drink &
press the SELECT
dial to adjust drink.
Press SELECT dial to save &
exit or press START|CANCEL
to exit without saving.
❷ Rotate the SELECT
dial to adjust,
Espresso Volume,
Milk Temperature
or Milk Froth level.
Press START/CANCEL
to exit the adjustments
menu.
Press the SELECT dial to enter
& rotate to adjust the setting.
Froth levels & Espresso Volumes
suggested settings are marked
with a dotted line.
Any milk coffee can be programmed.
1. Coffee Volume: from 25 to 60 ml / 0.85-2 oz.
2. Milk Temperature: from 55 to 75 °C / 131 to 167 °F.
3. Milk Froth: from 2 to 30 mm / 0.08 to 1.2 in.
21
Reset to Factory Settings
❶ Drink Settings are:
-Coffee Volume, Milk Temperature and Milk Froth.
EN
To reset your drink settings:
1. Select SETTINGS
2. Select RESET
3. Select COFFEE RESET
4. Select
5. Select
to confirm
to cancel
To reset factory settings:
1. Select SETTINGS
2. Select RESET
3. Select FACTORY RESET
4. Select
5. Select
6. Machine will power off
7. On next use, you will need to refer
to first use instructions
to confirm
to cancel
Emptying the System before a period of non-use or for frost protection /
❷ Rotate the SELECT dial to MAINTENANCE, press
❶ Remove the water tank.
Place the empty Milk Jug
under the coffee outlet.
SELECT dial. Select "Empty Cycle" & press SELECT
to start. When the pump stops, empty & wipe dry the
capsule bucket & drip tray.
22
EN
Energy Saving /
Daily Cleaning
To ensure hygienic conditions, it is highly recommended emptying and cleaning the capsule container every day.
❶ Energy efficient: Machine minimises power
use when not making a drink. The display dims
after 2 mins of no use, after 10 mins of no
use display turns off. Restart by pressing the
START|CANCEL button.
❷ Rinse the milk jug & dry
after each use.
If required, wash the jug
with mild detergent.
❶ Empty the drip tray and the capsule container every day. Remove cup
support by first removing the capsule bucket, then unlocking the cup support,
pulling the cup support forward & lifting it upwards to disengage from the
machine. Clean cup support and wipe inside machine, reassemble with a
clean damp cloth. Remove the water tank and lid and clean them both with
odorless detergent and rinse with warm water. Refill the water tank with fresh
potable water.
❸ Fill the milk jug with potable water
between the min & max marks. Select
the MILK function & press START. When
complete discard the hot water, then wipe
the steam wand with a clean damp cloth.
23
Daily Cleaning
EN
❹ Do not use any strong or
abrasive solvent, sponge or
cream cleaner. Do not put in
the dishwasher.
Steam Wand Cleaning Procedure
Milk System Cleaning Procedure.
Recommended you perform this monthly
to prevent steam tip blockages or when
the display shows "Clean Steam Wand".
Dry all the parts with a soft
clean cloth and reassemble
all parts. Clean the coffee
outlet and inside the machine
regularly with a clean damp
cloth.
Never immerse the
appliance or part of it in
water or any other liquid.
❶ Select Maintenance ❷ Select Clean Steam Wand ❸ Follow the on-screen prompts
24
EN
Descaling
Duration approximately 15 minutes.
Read the important safeguard on the descaling package
and refer to the table for the frequency of use.The
descaling solution can be harmful. Avoid contact with eyes,
skin and surfaces. Never use any product other than the
Nespresso descaling kit available at the Nespresso Club
to avoid damage to your machine. The following table will
indicate the descaling frequency required for the optimum
performance of your machine, based on water hardness.
For any additional questions you may have regarding
descaling, please contact the Nespresso Club.
Descaling: Removes scale build-up, maintains coffee taste and prevents machine damage.
Frequency will depend on your water hardness & amount of use. Descale when prompted
on-screen. The machine will stop you from use if the descale cycle has not been performed
after 10 uses. A "lockout" count-down will appear to alert you of the number of uses
remaining until usage will stop.
❶ Rotate dial to select MAINTENANCE
❷ Select DESCALE ❸ Follow the on-screen
prompts to complete
25
Water Hardness
To determine water hardness level
use the test strip provided.
To change the water hardness setting:
EN
❶ Rotate dial to select
SETTINGS
Water hardness:* Descaling after:*
App. fH dH CaCO
Level 0
< 5 < 3 < 50 mg/l 2 200
Level 1
> 7 > 4 > 70 mg/l 1 800
Level 2
> 13 > 7 > 130 mg/l 1 400
Level 3
Level 4
> 25 > 14 > 250 mg/l 1 000
> 38 > 21 > 380 mg/l 600
❷ Select Water Hardness ❸ Follow the on-screen
3
(40 ml)
prompts to complete
French degree
fH
German Grade
dH
Calcium Carbonate
3
CaCO
26
EN27EN
Troubleshooting
Buttons not illuminated.
No steam or hot water
No coffee, no water, unusual coffee flow.
Coffee is not hot enough.
The capsule lever does not close
completely
Leakage (water under the machine).
No coffee flow, water goes directly into
the capsule bucket (despite inserted
capsule).
Colour display is dim and hard to see/read
Buttons flashing
Fill Water Tank alert remains on display
(water tank is full)
Descale Now alert is displayed
Machine Error message is displayed
Machine is ON but ceases to operate
Machine turns to OFF mode.
- Machine turns OFF automatically. See paragraph on «Energy Saving
Concept».
- Press START/CANCEL or SELECT to turn to «ON-mode».
- Press START/CANCEL or SELECT to turn to «ON-mode». - Check the outlet: plug, voltage, fuse.
- Check if the water tank is correctly positioned, if empty, fill with potable
water.
- Preheat cup. - Descale the machine, if necessary.
- Empty the capsule container. - Check that no capsule is blocked inside the machine. (Note: do not put the
- Empty drip tray if full.
- Check drip tray is securely inserted.
- Ensure capsule lever is closed. - Empty capsule bucket and check that no capsule is blocked inside the
- Machine display dims automatically after 2 minutes of non use.
- See paragraph on «Energy Saving Concept».
- Press START/CANCEL or SELECT to turn to «ON-mode».
- Follow on screen prompt.
- Check the water tank. If empty, fill with potable water and brew a coffee.
- Check steam tip for blockages. Use pin cleaning tool stored under the water
tank to unblock each of the holes.
- Check if the water tank is correctly positioned. - If problem persists, call the Nespresso Club.
- Descale the machine. Navigate to Maintenance menu.
- Select Descale and follow the on-screen prompts.
- A major fault has occurred. - Visit Nespresso.com or call the Nespresso Club to contact your local service
- Power machine off by holding START/CANCEL.
- Wait 60 minutes and press START/CANCEL or SELECT to turn to «ON-mode». - If problem persists, call the Nespresso Club.
- To save energy the machine will turn to OFF mode after 10 minutes of non
use. See paragraph on «Energy Saving Concept».
- Check the outlet: plug, voltage, fuse.
- Descale the machine, if necessary.
finger inside the machine)
- If problem persists, call the Nespresso Club.
machine. (NOTE: do not put finger inside the machine) If problem persists, call
the Nespresso Club.
- Adjust the screen brightness setting. Navigate to Settings menu. Select Screen
Brightness. Turn the dial and Select High.
- Descale machine, if necessary.
- Complete a Clean Steam Wand cycle, if necessary.
centre.
- Press START/CANCEL or SELECT to turn to «ON-mode».
Troubleshooting Milk Froth Preparation
EN
Milk steam cycle does not start
Quality of froth not up to standard
Steam is very wet
Milk overflows
Milk temperature is too hot
Milk temperature is not hot enough
Lower Wand alert is displayed
Clean Steam Wand alert is displayed
- Check if the water tank is correctly positioned, if empty, fill with potable water.
- Check steam tip for any blockages and ensure wand is lowered.
- Be sure to use pasteurised whole or semi-skimmed milk at refrigerated
temperature (about 4-6 °C / 39-43 F). For a better result, the milk must be
newly opened.
- Check the milk froth setting.
- Use cold, potable water. Do not use highly filtered, demineralised or distilled
water.
- Fill jug with appropriate milk volume.
- Minimum fill level as marked on the inside & outside of the jug.
- Maximum fill level as marked on the inside & outside of the jug.
- Be sure to use the Breville milk jug provided.
- Check the milk jug is positioned correctly on the milk jug temperature sensor.
- Check the temperture sensor in the drip tray is clean.
- Preheat cup.
- Use the Breville milk jug provided.
- Check the milk jug is positioned on the milk jug temperature sensor.
- Ensure the steam wand is lowered.
- Clean the Steam Wand. - Navigate to Maintenance menu. Select Clean Steam Wand and follow the
- Use the Breville milk jug provided.
- Clean both the milk jug and steam wand after each use.
- Clean the steam wand. Navigate to Maintenance menu.
- Select Clean Steam Wand and follow the on-screen prompts.
- To stop overflow, either reduce the initial volume of milk and/or reduce the froth
level. This varies depending on milk type.
- Decrease the milk temperature setting.
- Increase the milk temperature setting.
- Check the steam tip for blockages.
on-screen prompts.
28
EN
Contact the Nespresso Club
As we may not have foreseen all uses of your appliance, should you need
any additional information, in case of problems or simply to seek advice, call the
Nespresso Club or your Nespresso authorized representative.
Contact details for your Nespresso Club or your Nespresso authorized
representative can be found in the «Welcome to Nespresso» folder in your
machine box or at nespresso.com
Disposal and Environmental Protection
Your appliance contains valuable materials that can be recovered or can
be recyclable. Separation of the remaining waste materials into different
types facilitates the recycling of valuable raw materials. Leave the appliance
at a collection point. You can obtain information on disposal from your local
authorities.
29
Limited Guarantee
Breville guarantees this product against defects in materials and workmanship for two years domestic use (or 3 months commercial use) from the date of purchase.
During this period, Breville will either repair or replace, at its discretion, any defective product at no charge to the consumer. In the event of a product or accessory
being repaired or replaced during the guarantee period, the guarantee on the repaired product will expire two years from the purchase date of the original product,
not two years from the date of repair. This guarantee excludes liability for consequential loss or any other loss or damage caused to property or person arising from
any cause whatsoever. It also excludes defects caused by the product not being used in accordance with instructions, accidental damage, misuse, being tampered
with by unauthorised persons, improper maintenance, consumable items or normal wear and tear and does not cover the cost of claiming under the warranty.
How to Claim Under the Breville Warranty
Nespresso is handling product enquiries and product servicing on Breville’s behalf. If you believe your product is defective, contact the Nespresso customer service
team directly for instructions on where to send or bring it for repair by a Breville authorised service agent. Contact Nespresso Australia: 1800 623 033 or
New Zealand: 0800 234 579 auclub@nespresso.com.
This product is imported and distributed by Breville and this warranty is provided by Breville. To the extent permitted by law, Nespresso has no liability for the product
and all guarantees, warranties and conditions by Nespresso are excluded.
EN
30
Loading...