Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Due to continued product improvement, the products illustrated/photographed
in this brochure may vary slightly from the actual product.
Copyright Breville Pty. Ltd. 2013.
New Zealand Customers
Mail: Private Bag 94411
Greenmount, Auckland
NEW ZEALAND
Phone:
0800 273 845
Fax: 0800 288 513
Email:
Customer Service:
askus@breville.com.au
Model BFP450 Issue - B13
the Kinetix™ Wizz™
Instruction Booklet
BFP450
CONGRATULATIONS
on the purchase of your new Breville product
CONTENTS
4 Breville recommends safety first
7 Know your Breville product
10 Before first use
16 Operating your Breville product
18 Basic food processing techniques
22 Blending and food processing tips
25 Care & cleaning
28 Recipes
3
BREVILLE RECOMMENDS SAFETY FIRST
At Breville we are very safety conscious. We design and manufacture consumer products with
the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise
a degree of care when using any electrical appliance and adhere to the following precautions.
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE FOR
FUTURE REFERENCE
• Carefully read all instructions before
operating the Breville food processor
and blender for the first time and save
for future reference.
• Remove and safely discard any packaging
material and promotional labels before
using the food processor or blender for
the first time.
• To eliminate a choking hazard for young
children, remove and safely discard the
protective cover fitted to the power plug
of this appliance.
• Do not place the food processor or
blender near the edge of a bench or table
during operation. Ensure the surface is
level, clean and free of water and other
substances.
• Do not use the food processor or blender
on a sink drain board.
• Do not place the food processor or blender
on or near a hot gas or electric burner, or
where it could touch a heated oven.
• Handle the food processor, blender jug and
attachments with care – remember the blades
and discs are razor-sharp and should be kept
out of the reach of children.
• Be careful when emptying the processor
bowl and blender jug and during
cleaning. Mishandling of the blades may
cause injury.
• Use the blade protector when storing the
processing blade.
• Always ensure the food processor or
blender is completely assembled before
operating. The appliance will not operate
unless properly assembled.
• Ensure the speed selection dial is in the
OFF position and the food processor or
blender is switched off at the power outlet
and the power cord is unplugged before
attaching the processing blade, discs or
processing lid.
• Switch off the appliance and disconnect
from supply before changing accessories
or approaching parts that move in use.
• Always secure the processing bowl onto
the motor base before attaching the
processing blade or discs.
• Always operate the food processor or
blender with the lid in position.
• Do not push food into the processing
chute with your fingers or other utensils.
Always use the food pusher provided.
• Keep fingers, hands, knives and
other utensils away from moving
blades and discs.
• Never place your fingers, hands or
utensils inside the processor bowl or
blender jug without unplugging the
appliance from the power outlet.
• Do not place hands or fingers into the
processing bowl of the food processor
or blender jug unless the motor, blender
blade and discs have come to a complete
stop. Ensure the speed selection dial is
in the OFF position and the appliance is
switched off at the power outlet and the
power cord is unplugged before removing
the lid from the food processor bowl and
blender jug.
4
BREVILLE RECOMMENDS SAFETY FIRST
• Ensure the motor and blade or discs have
completely stopped before disassembling.
Ensure the speed selection dial is in
the OFF position and the appliance is
switched off at the power outlet and
the power cord is unplugged from the
power outlet before attempting to move
the appliance, when not in use, if left
unattended and before disassembling,
cleaning or storing.
• Do not use attachments other than
those provided with the food processor
or blender.
• Do not attempt to operate the food
processor or blender by any method other
than those described in this booklet.
• Care should be taken when removing
the food from the processing bowl by
ensuring the motor and the processing
blade or disc, have completely stopped
before disassembling. Ensure the speed
selection dial is turned to the OFF
position, the appliance is switched off
at the power outlet and unplugged,
before removing the lid from the bowl.
The processing bowl should then be
unlocked from the motor body and the
processing blade or disc holder carefully
removed before attempting to remove the
processed food.
• If food becomes lodged around the
blending blade, turn the speed selection
dial to the OFF position, then switch
the appliance off at the power outlet and
unplug the cord. Make sure the motor and
blades have completely stopped before
removing the jug from the motor base.
Use a spatula to dislodge or stir the food
before continuing. Do not use fingers as
the blades are sharp.
• Some stiff mixtures, such as dough, may
cause the dough blade to rotate more
slowly than normal. In this unlikely event
of an excessive load, do not operate the
appliance continuously with excessive load
for more than 1 minute.
• Do not operate the food processor
continuously for periods longer than
3 minutes on any setting or if processing
a heavy load. Do not operate the blender
continuously for periods longer than
1 minute on any setting. None of the
recipes in this book should require
processing for longer than 3 minutes
or blending longer than 1 minute and
none are considered a heavy load. If the
food processor or blender is operated
continuously for too long, it should be
allowed to rest for 25–30 minutes before
recommencing.
• Do not process hot or boiling liquids –
allow liquids to cool before placing into
the processing bowl or blending jug.
• Do not move the food processor or
blender whilst in operation.
• Do not leave the food processor or blender
unattended when in use.
• Do not place any part of the food
processor and blender in the dishwasher
or microwave oven.
• Do not process thin fluids such as water,
milk, stock, juice, etc. above the 500ml
level in the processing bowl as this could
result in overflow. To reduce the risk
of overflow, always add drier or thicker
ingredients to the processing bowl prior
to adding fluids.
• Do not place anything on top of the food
processor or blender when the lid is on,
when in use and when stored.
• Keep the food processor and blender
clean. Follow the cleaning instructions
provided in this book.
• Do not remove the blender jug from the
motor base while in operation.
• Do not use the blender for anything other
than food and/or beverage preparation.
• Do not operate the blender without food
or liquid in the blender jug.
• Do not subject the blender jug to extremes
of hot or cold, for example, placing a cold
jug in hot water or vice versa.
5
5
BREVILLE RECOMMENDS SAFETY FIRST
IMPORTANT SAFEGUARDS FOR
ALL ELECTRICAL APPLIANCES
• Fully unwind the power cord before use.
• Do not let the power cord hang over
the edge of a bench or table, touch hot
surfaces or become knotted.
• To protect against electric shock do not
immerse the power cord, power plug or
motor base in water or any other liquid.
• The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
• It is recommended to regularly inspect
the appliance. To avoid a hazard do not
use the appliance if power cord, power
plug or appliance becomes damaged in
any way. Return the entire appliance to
the nearest authorised Breville Service
Centre for examination and/or repair.
• Any maintenance other than cleaning
should be performed at an authorised
Breville Service Centre.
• This appliance is for household use only.
Do not use this appliance for anything
other than its intended use. Do not use
in moving vehicles or boats. Do not use
outdoors. Misuse may cause injury.
• The installation of a residual current
device safety switch is recommended
to provide additional safety protection
when using electrical appliances. It is
advisable that a safety switch with a rated
residual operating current not exceeding
30mA be installed in the electrical
circuit supplying the appliance. See your
electrician for professional advice.
CAUTION
In order to avoid a hazard due to
inadvertent resetting of the thermal
cut-out, this appliance must not
be supplied through an external
switching device, such as a timer, or
connected to a circuit that is regularly
switched on and off by the utility.
CAUTION
The processing blade, discs and
blending blades are extremely sharp,
handle with care at all times. Do not
place hands, knives, or other utensils
into the food chute or blender jug.
Always use the food pusher to push the
food down the food chute.
SAVE THESE
INSTRUCTIONS
6
KNOW
your Breville product
KNOW YOUR BREVILLE PRODUCT
A
F
B
C
D
E
A. Inner Measuring Cup
B. Processing Bowl Lid
C. 2.0L Processing Bowl
D. Speed Selection Dial
G
E. Direct Drive Motor Base
F. Food Pusher
G. Automatic Safety Locking System
Prevents food processor from operating
unless the bowl and lid are correctly
engaged on the motor base.
H. Slicing Disc
8
KNOW YOUR BREVILLE PRODUCT
H
IJK
SR
L
MNQ
OP
I. Chipping Disc
J. Shredding Disc
K. Disc Holder
L. Stainless Steel Processing Blade
M. Processing Blade Protective
Storage Cover
N. Dough Blade
O. Whisk
P. Spindle
Supports processing blade,
dough hook and disc holder.
Q. 1.5L Jug
R. Inner Measuring Cup
TM
S. Breville Assist
lid.
9
BEFORE FIRST USE
of your Breville product
BEFORE FIRST USE
PREPARING THE FOOD PROCESSOR
AND BLENDER FOR USE
Remove and safely discard all packaging
materials and promotional labels. Wash
the food processor bowl, blender jug, lid
and other attachments in warm soapy
water using a mild detergent. Rinse and
dry thoroughly. (Refer to Care & Cleaning
section of this booklet.)
NOTE
The blending blades and food
processor blades are extremely
sharp. Avoid any contact with
fingers and hands.
ATTACHING THE FOOD
PROCESSOR BOWL
The food processor bowl and lid must be
correctly assembled for the food processor
to operate.
1. Place the motor base on a flat, dry surface
such as a bench top. Make sure that the
motor base is turned off at the power
outlet and the power cord is unplugged.
2. Place the processing bowl (with the
lid off) over the drive shaft and onto
the motor base with the handle facing
forward. Turn the processing bowl
counter-clockwise to lock into position.
3. Insert the spindle into the food
processor bowl by placing it over the
shaft in the centre of the bowl and
rotating until it falls into place.
ASSEMBLING THE STAINLESS STEEL
PROCESSING BLADE
1. Carefully remove the protective storage
cover from the processing blade.
2. Carefully place the processing blade
over the centre of the spindle.
3. Release the processing blade so that it
drops to the bottom of the spindle and
falls into place.
4. Place the food to be processed into the
processing bowl as indicated in the recipe.
11
BEFORE FIRST USE
ASSEMBLING THE STAINLESS
STEEL SLICING/ SHREDDING/
CHIPPING DISCS
1. Carefully select the desired disc to be
used (slicing, shredding or chipping).
2. Slide the blade (sharp side facing up)
into the side grooves of disc holder.
Continue to push the disc into place
until it covers the 2 small black tabs in
the centre of the disc holder.
3. Hold the disc by sliding your thumb and
index fingers into the holes of the disc
holder. Place the assembled disc holder
onto the spindle and release so that it falls
into place.
ASSEMBLING THE DOUGH BLADE
1. Place the dough blade over the centre of
the spindle.
2. Release the dough blade so that it drops
to the bottom of the spindle and falls
into place.
3. Place the food to be processed into the
processing bowl as indicated in the recipe.
ASSEMBLING THE WHISK
1. Place the whisk over the centre of
the spindle.
WARNING
The processing blade and the discs
are extremely sharp. Use caution when
handling and storing these parts.
12
2. Release the whisk so that it drops to the
bottom of the spindle and falls into place.
3. Place the food to be processed into the
processing bowl as indicated in the recipe.
BEFORE FIRST USE
ATTACHING THE LID
Attach the lid by placing it on the
processing bowl ensuring the
on the lid is aligned with the
the bowl.
To lock the lid in place, hold the feed chute
and turn the lid counter clockwise so the
symbol on the lid aligns with the
on the handle.
Ensure the lid is positioned securely. Insert
the food pusher and measuring cup into
position in the food chute.
NOTE
Ensure the spindle, blade, disc and
disc holder are clean and free of food
residue before attaching the lid.
symbol
symbol on
ALIGN
LOCK
symbol
ASSEMBLING AND ATTACHING
THE BLENDER
1. Place the motor base on a flat, dry
surface such as a bench top. Ensure
that the motor base is switched off at
the power outlet and the power cord is
unplugged.
2. Place the blender jug over the drive shaft
and onto the motor base with the handle
facing forward.
3. Turn the blender jug counter-clockwise
to lock into position.
NOTE
The food processor will not operate
unless the processing bowl and lid
are positioned correctly and locked
into position.
4. Add food or liquid into the blender jug
ensuring not to exceed the MAX mark.
5. Place the blender lid firmly into position
on the top of the blender jug.
13
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.