Breville BFP250 User Manual
Wizz™ Multi Processor
Instructions and Recipes
BFP250
Breville is a registered trademark of Breville Pty. Ltd.
ABN 98 000 092 928
Breville Customer Service Centre
Australian Customers
Breville Customer Service Centre
PO Box 22
Botany NSW 2019
AUSTRALIA
Customer Service: 1300 139 798
F
ax (02) 9384 9601
Email Customer Service: askus@breville.com.au
New Zealand Customers
Breville Customer Service Centre
Private Bag 94411
Greenmount
Auckland, New Zealand
Customer Service: 0800 273 845
F
ax 0800 288 513
Email Customer Service: askus@breville.com.au
www.breville.com.au
© Copyright. Breville Pty. Ltd. 2008
Due to continual improvements in design or otherwise,
the product you purchase may differ slightly from the one
illustrated in this booklet.
Model: BFP250 Issue 1/08
Contents
Page
Breville recommends safety first 4
Know your Breville Wizz™ Multi Processor 6
Assembly and operation of your Breville Wizz™
Multi
Processor 7
Care, Cleaning and Storage 12
The stainless steel processing blade 14
Processing disc inserts
– The stainless steel slicing disc 16
– The stainless steel coarse shredding disc 18
– The stainless steel fine shredding disc 18
Functions available at a glance 19
Recipes 20
2
Congratulations
on the purchase of your new Breville Wizz™ Multi Processor
5
Breville recommends safety first
4
We at Breville are very safety conscious. We design and manufacture consumer products with the
safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree of
care when using any electrical appliance and adhere to the following precautions:
IMPORTANT SAFEGUARDS FOR YOUR BREVILLE WIZZ™ MULTI PROCESSOR
Carefully read all instructions before operating
and save for future reference.
Remove and safely discard any packaging
material and promotional labels before using
the Breville Wizz™ Multi Processor for the
first time.
To eliminate a choking hazard for young
children, remove and safely discard the
protective cover fitted to the power plug of
this appliance.
Do not place the Breville Wizz™ Multi
Processor near the edge of a bench or table
during operation. Ensure the surface is level,
clean and free of water, flour and other
substances. Vibration during operation may
cause the appliance to move.
Do not place the Breville Wizz™ Multi
Processor on or near a hot gas or electric
burner, or where it could touch a heated oven.
Handle the Breville Wizz™ Multi Processor
and attachments with care – remember the
blades and discs are razor-sharp and should
be kept out of reach of children. Use the blade
protector when storing the processing blade.
Always ensure the Breville Wizz™ Multi
Processor is completely assembled before
operating. The appliance will not operate
unless properly assembled.
Ensure the Speed Selection Dial is in the
Off ‘O’ position and the food processor is
switched off at the power outlet and the
power cord is unplugged before attaching the
processing blade, discs or processing lid.
•
•
•
•
•
•
•
•
Always secure the processing bowl onto the
motor base before attaching the processing
blade or discs.
Always operate the food processor with the
processing lid in position.
Do not push food into the food chute with your
fingers or other utensils. Always use the food
pusher provided.
Keep fingers, hands, knives and other utensils
away from moving blades and discs.
Do not place hands or fingers in the
processing bowl of the food processor unless
the motor, processing blade and discs have
come to a complete stop. Ensure the Speed
Selection Dial in the Off ‘O’ position and the
appliance is switched off at the power outlet
and the power cord is unplugged before
removing the lid from the food processing
bowl.
Ensure the motor and blade or discs have
completely stopped before disassembling.
Ensure the Speed Selection Dial is in the Off
‘O’ position and the appliance is switched
off at the power outlet and the power cord
is unplugged from the power outlet before
attempting to move the appliance, when
not in use, if left unattended, and before
disassembling, cleaning or storing.
Do not use attachments other than those
provided with the Breville Wizz™ Multi
Processor.
Do not attempt to operate the Breville Wizz™
Multi Processor by any method other than
those described in this booklet.
•
•
•
•
•
•
•
•
IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES
Unwind the power cord fully before use.
Do not let the power cord hang over the edge
of a bench or table, touch hot surfaces or
become knotted.
The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance by
a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
It is recommended to regularly inspect
the appliance. Do not use the appliance if
power supply cord, power plug or appliance
becomes damaged in any way. Return the
entire appliance to the nearest authorised
•
•
•
•
•
Breville service centre for examination and/or
repair.
Any maintenance, other than cleaning, should
be performed at an authorised Breville Service
Centre.
This appliance is for household use only. Do
not use this appliance for anything other than
its intended use. Do not use moving vehicles
or boats. Do not use outdoors. Misuse may
cause injury.
The installation of a residual current device
(safety switch) is recommended to provide
additional safety protection when using
electrical appliances. It is advisable that a
safety switch with a rated residual operating
current not exceeding 30mA be installed in
the electrical circuit supplying the appliance.
See your electrician for professional advice.
•
•
•
Breville recommends safety first (continued)
CAUTION: THE PROCESSING BLADE AND DISCS ARE EXTREMELY SHARP, HANDLE WITH
CARE AT ALL TIMES.
CAUTION: DO NOT PLACE FINGERS, HANDS, KNIVES OR OTHER UTENSILS INTO
THE FOOD CHUTE. ALWAYS USE THE FOOD PUSHER TO GUIDE FOOD DOWN THE
FOOD CHUTE.
Care should be taken when removing the
food from the food processor by ensuring
the motor, processing blade and discs have
completely stopped before disassembling.
Ensure the Speed Selection Dial is turned to
the Off ‘O’ position, the appliance is switched
off at the power outlet and unplugged,
before removing the lid from the bowl. The
processing bowl should then be unlocked
from the motor body and the processing
blade or disc holder carefully removed before
attempting to remove the processed food.
Do not operate the food processor
continuously for periods longer than 3 minutes
on any setting or if processing a heavy load.
None of the recipes in this booklet should
require processing for longer than 3 minutes
and none are considered a heavy load. If the
food processor is operated continuously for
too long, it should be allowed to rest for 2530 minutes before recommencing.
•
•
Do not use food processor on a sink drain
board.
To protect against electric shock do not
immerse power cord, power plug or motor
base in water or any other liquid.
Do not move the food processor whilst in
operation.
Do not leave the food processor unattended
when in use.
Do not place any part of the food processor in
the dishwasher or microwave oven.
Do not process thin fluids such as water,
milk, stock, juice, etc. above the 200ml level
in the processing bowl as this could result
in overflow. To reduce the risk of overflow,
always add drier or thicker ingredients to the
processing bowl prior to adding fluids.
Keep the appliance clean. Follow the cleaning
instructions provided in this book.
•
•
•
•
•
•
•
Before first use
Remove and safely discard all packaging
materials and promotional labels from your
Breville Wizz™ Multi Processor.
Wash the food processor bowl, lid and other
attachments in warm soapy water using a mild
detergent. Rinse and dry thoroughly. (Refer
to Care, Cleaning and Storage section of this
booklet.)
Attaching the food processor bowl
The food processor bowl and lid must be
correctly assembled for the food processor to
operate.
Step 1
Place the motor base on a flat, dry surface such
as a bench top. Make sure that the motor base
is turned off at the power outlet and the power
cord is unplugged.
Step 2
Place the processing bowl over the drive shaft
and onto the motor base (see Fig 1). Turn the
processing bowl clockwise to lock into position
(Fig 2).
Step 3
Select either the processing blade or a slicing
or shredding disc (Refer Pages 8 and 9) for
assembly.
Each time you reassemble your Breville Wizz™
Multi Processor be sure to attach the processing
bowl first and lock it into position before attaching
the lid.
The processing of thin fluids such as water,
milk, stock, juice, etc. above the 200ml level in
the processing bowl could result in overflow.
To reduce the risk of overflow, always add
drier or thicker ingredients to the processing
bowl prior to adding thin fluids.
Assembly and operation of your
Breville Wizz™ Multi Processor
7
Know your Breville Wizz™ Multi Processor
6
Fig.1
Fig.2
Food pusher
80ml measuring cup insert guides
food down the food chute
Processing bowl
with 1.2 litre capacity
Automatic Safety Lockout System
prevents food processor from operating unless the bowl
and lid are correctly engaged on the motor base
Speed selection dial
with a choice of 3 speeds
plus pulse for complete
processing control
Non-skid feet
ensures the food processor
remains stable
High performance 500 watt Motor Base
Attachments not shown:
Spatula – for easy removal of food from bowl. Spatula handle is designed to dislodge food from the inside of the
processing blade shaft
Stainless steel slicing disc – perfect for slicing meats, vegetables, fruit and cheese
Stainless steel fine shredding disc – excellent for shredding chocolate and hard cheeses such as Parmesan
Stainless steel coarse shredding disc – ideal for shredding all types of fruit, vegetables and cheese
Processing blade protective storage cover – used for safe storing of sharp blades
Disc holder spindle – insert into the processing bowl to support the disc holder
Disc holder – discs lock easily into place
Storage container – for discs and disc holder
•
•
•
•
•
•
•
•
Stainless steel
processing blade
is perfect for all chopping,
mixing and blending tasks
9
Assembly and operation of your
Breville Wizz™ Multi Processor
continued
8
Using the stainless steel slicing/
shredding discs
Place the disc holder spindle onto the shaft
in the processing bowl.
Fit disc onto disc holder by placing the wider
lug on end of disc, into one side of the disc
holder opening (Fig 3). Lower the disc down
over shaft hole then push disc down to lock
into position (Fig 4). To remove disc, hold disc
holder with the disc facing away and place
thumbs underneath the end of disc marked
‘Push Up’ and push out (Fig 5).
Place the disc holder onto the disc holder
spindle.
1.
2.
3.
Fig.3
Fig.4
Fig.5
WARNING: WHEN SLICING AND SHREDDING, ALWAYS USE THE FOOD PUSHER TO
GUIDE FOOD DOWN THE FOOD CHUTE. NEVER PUT YOUR FINGERS OR SPATULA INTO
THE FOOD CHUTE. ALWAYS WAIT FOR THE DISC TO STOP SPINNING BEFORE REMOVING
THE LID.
THE PROCESSING BLADE AND THE DISCS ARE EXTREMELY SHARP!! USE CAUTION
WHEN HANDLING AND STORING THESE PARTS.
Using the stainless steel processing
blade
Carefully remove the protective storage
cover from the processing blade.
Place the processing blade over the drive
shaft (see Fig 6). Rotate it slowly until
it settles into place. When handling the
processing blade, always hold by the spindle
(as shown in Fig 7).
Place the food to be processed into the
processing bowl as indicated in the recipe.
To avoid over-processing, check the
consistency frequently when the food being
processed requires a coarse or thick texture. If
necessary, turn the Speed Selection Dial to the
Off ‘O’ position, switch off at the power outlet,
unlock the lid and use the spatula to scrape
down the sides of the bowl to ensure even
processing.
Care
should be taken when removing the food
from the processing bowl by ensuring the
motor and the processing blade or disc, have
completely stopped before disassembling.
Ensure the Speed Selection Dial is turned to
the Off ‘O’ position, the appliance is switched
off at the power outlet and unplugged, before
removing the lid from the bowl. The processing
bowl should then be unlocked from the motor
body and the processing blade or disc holder
carefully removed before attempting to remove
the processed food.
1.
2.
3.
Fig.6
Fig.7
Assembly and operation of your
Breville Wizz™ Multi Processor
continued
10 11
Attaching the lid
Attach the lid by placing the lid on the processing
bowl with the food chute positioned slightly left
of the bowl handle and aligning the spindle of
the processing blade or disc holder with the
bowl lid bearing located under the white button
in the centre of the lid (see Fig 8). Turn the lid
clockwise to slide the locking tab on the lid into
the interlocking safety slot in the motor base (see
Fig 9). Ensure the lid is positioned securely. Insert
the food pusher and measuring cup into position
in the food chute (Fig 10).
Ensure the fine end of the processing blade or
disc holder spindle and the hole in the bowl
lid bearing, located under the white button in
the centre of the lid, are clean and free of food
residue before attaching the lid.
The Breville Wizz™ Multi Processor will not
operate unless the processing bowl and lid are
positioned correctly and locked into position.
Fig.9
Fig.10
Commence processing
Step 1
To commence processing, insert the power plug
into a power outlet and switch on. Select a speed
on the Speed Selection Dial by turning clockwise
one notch for Speed 1, two notches for Speed 2,
or three notches for Speed 3 or turn anticlockwise
for ‘Pulse’ (see Fig 11).
Step 2
Processing blade
When using the processing blade, the food to be
processed should be placed into the processing
bowl before locking the lid into position.
However, some recipes call for liquids, etc. to
be added during processing. To do this, remove
the measuring cup from the food pusher and
slowly pour the liquid through the narrow
opening.
Slicing/shredding discs
When using the slicing or shredding discs, the
food is placed into the food chute and pushed
down onto the rotating disc using the food
pusher. To support narrow food items, when
processing, position the food pusher into the
food chute, insert the food into the narrower
opening and use the measuring cup as the food
pusher.
Fig.8
Fig.11
Assembly and operation of your
Breville Wizz™ Multi Processor
continued
Assembly and operation of your
Breville Wizz™ Multi Processor
continued
Loading...