www.braun.co.jp
o
t
u
n
r
P
o
r
C
o
e
e
v
v
i
i
t
t
i
i
s
s
n
n
e
e
s
s
on
•
off
full
low
23456
8000
lo
w
on
•
off
full
C
o
n
t
o
u
r
P
r
o
s
e
n
s
i
t
i
v
e
Series
washable
STOP
10
11
1
2
2
1
3
4
o
t
u
n
r
P
o
r
C
5
o
e
e
v
v
i
i
t
t
i
i
s
s
n
n
e
e
s
s
on
•
off
6
7
8
9
8374
7
8
9
8377
12
7
891011121314
C
o
n
t
o
u
r
P
r
o
s
e
n
s
i
t
i
v
e
on
P
•
off
C
s
o
e
n
t
n
o
u
s
r
P
r
i
o
t
i
v
e
u
o
r
t
P
n
r
o
o
C
e
v
i
t
i
s
n
e
s
t
o
n
u
o
r
C
15
C
o
n
t
o
u
r
P
r
o
s
e
n
s
i
t
i
v
e
16
17181920212223
English
Our products are designed to meet the
highest standards of quality, functionality and
design. We hope you enjoy your new Braun
Shaver.
Warning
Your shaver is provided with a special cord
set, which has an integrated Safety Extra Low
Voltage power supply. Do not exchange or
tamper with any part of it, otherwise there is
risk of electric shock.
Description
1 Shaver foil
2 Cutter block
3 Foil release buttons
4 Long hair trimmer
5 Comfort setting switch «sensitive»
6 On/off switch
7 Shaver display
8 Replacement light for shaving parts
9 Reset button
10 Shaver power socket
11 Special cord set
12 Etui
Charging
The best environmental temperature for
charging is between 5 °C and 35 °C. Do not
expose the shaver to temperatures higher
than 50 °C for extended periods of time.
Using the special cord set (11), connect the
•
shaver to an electrical outlet with the motor
switched off and charge it for at least one
hour.
A full charge provides up to 45 minutes of
•
cordless shaving time. This may vary
according to your beard growth.
If the rechargeable battery has run out of
•
power (discharged), you may also shave by
connecting the shaver to an electrical outlet
via the special cord set.
Shaver display
The shaver display (7) shows the charge
status of the battery. During charging or
when using the shaver, the respective green
battery segment will blink. When fully
charged, all green segments will light up
continuously, provided the shaver is switched
on or connected to an electrical outlet.
The red low charge segment flashes when
the battery capacity has dropped below
20%, provided the shaver is switched on.
The remaining capacity will then be sufficient
for 2 to 3 shaves.
Shaving
Press the on/off switch (6) to operate the
shaver.
Comfort setting switch «sensitive» (5)
Setting the shaver head according to your
comfort needs.
The «sensitive» switch (5) provides three
options for comfort setting:
1 « + » :
The shaver head is in full swing, freely
follows the contours of your skin to
provide more comfort.
2 middle position:
The shaver head is semi-fixed for more
control.
3 « – » :
The shaver head is fixed for full control
and precise handling in hard to reach
areas.
Long hair trimmer (4)
To trim sideburns, moustache or beard, slide
the long hair trimmer upwards.
Tips for the perfect shave
For best shaving results, Braun
recommends you to follow 3 simple steps:
1. Always shave before washing your face.
2. At all times, hold the shaver at right
angles (90°) to your skin.
3. Stretch your skin and shave against the
direction of your beard growth.
completely). Switch on the shaver for
approx. 5–10 seconds so that the shaved
stubbles can fall out.
•
Switch off the shaver. Remove the shaver
foil and tap it out on a flat surface. Using
the brush, clean the inner area of the
shaver head. However, do not clean the
shaver foil nor the cutter block with the
brush as this will damage them.
Cleaning
The shaver head is suitable for
cleaning under running tap water.
Warning: Detach the shaver from the
power supply before cleaning the
shaver head in water.
Regular cleaning ensures better shaving
performance. Rinsing the shaving head under
running water after each shave is an easy
and fast way to keep it clean (A):
Switch the shaver on (cordless) and rinse
•
the shaver head under hot running water.
You may use liquid soap without abrasive
substances. Rinse off all foam and let the
shaver run for a few more seconds.
Next, switch off the shaver, press the foil
•
release buttons (3) to remove the shaver
foil (1) and cutter block (2). Then leave the
disassembled shaving parts to dry.
If you regularly clean the shaver under
•
water, apply a drop of the light machine oil,
included with the shaver, onto the shaver
foil and long hair trimmer. This is critical for
proper functioning of the shaver as
washing under water can lead to removal
of lubricants from the shaver’s cutting parts
leading to higher friction in the shaver. This
may result in the battery running out faster
than normal. Even if this happens –
indicated by low charge indicator lighting
up earlier, your Braun shaver will run for at
least 5 more minutes enabling you to
complete your current shave.
The following quick cleaning is another
alternative cleaning method (B):
Press the foil release buttons (3) to lift
•
the shaver foil (do not remove the foil
Keeping your shaver in top
shape
Replacing the shaver foil and cutter
block / reset
To maintain 100% shaving performance,
replace the shaver foil (1) and cutter block (2),
when the replacement symbol (8) lights up
(after about 18 months) or when worn.
The replacement symbol will remind you
during the next 7 shaves to replace the
shaving parts. Then the shaver will automatically reset the display.
After you have replaced the shaving parts
(foil and cutter block), use a ball-pen to push
the reset button (9) for at least 3 seconds to
reset the counter.
While doing so, the replacement light blinks
and goes off when the reset is complete.
The manual reset can be done at any time.
Accessories
Available at your dealer or Braun Repair
Centres:
Shaver foil and cutter block: Series 8000
Environmental notice
This product contains rechargeable
batteries. In the interest of protecting
the environment, please do not
dispose of the product in the household waste at the end of its useful life.
Disposal can take place at a Braun Repair
Centre or at appropriate collection points
provided in your country.
24
The cleaning cartridge can be disposed with
regular household waste.
Subject to change without notice.
This p roduct conforms to the European
Directives EMC 89/336/EEC and Low
Voltage 2006/95/EC.
For electric specifications, see printing on the
special cord set.
25
27
5-753-429/01/V-07
Japan/GB
Loading...