Brady BDC2000 Users Manual

_______________________________________________________________________________

Brady BDC2000 RFID Assembly

BDC2000 RFID PCB ANT2000 Antenna PCB

MANUFACTURER HEADQUARTERS:

Brady Worldwide, Inc.
6555 W Good Hope Road
Milwaukee, WI 53223 USA

_______________________________________________________________________________

Table of Content

_Toc453241779

1. Introduction ................................................................................................................. 8

1.1 Description........................................................................................................... 8

1.2 Specification ........................................................................................................ 9

2. Installation ................................................................................................................. 10

2.1 Connections ....................................................................................................... 11

3. Operation ................................................................................................................... 12

List of Figures

Figure 1. Block Diagram of Brady BDC2000 RFID Assembly and Connection to Host ... 8

Figure 2. photo of the Brady BDC2000 RFID Assembly ................................................. 10

List of Tables

Table 1. Specification of Brady BDC2000 RFID Assembly.............................................. 9

Table 2. JST B6B-PH-K-S ................................................................................................ 11

Table 3. JST B2B-PH-K-S ................................................................................................ 11

Table 4. Samtec 10-Position Dual Row ............................................................................. 11

Table 5. BDC SPI Configuration ....................................................................................... 12

_______________________________________________________________________________

Copyright

This manual is copyrighted with all rights reserved. No portion of this manual may
be copied or reproduced by any means without the prior written consent of BRADY
Worldwide, Inc.

While every precaution has been taken in the preparation of this document, BRADY
assumes no liability to any party for any loss or damage caused by errors or
omissions or by statements resulting from negligence, accident, or any other cause.
BRADY further assumes no liability arising out of the application or use of any
product or system described, herein; nor any liability for incidental or consequential
damages arising from the use of this document. BRADY disclaims all warranties or
merchantability of fitness for a particular purpose.

Trademarks

Brady BDC2000 RFID Assembly is a trademark of BRADY Worldwide, Inc.

Microsoft and Windows are registered trademark of Microsoft Corporation.

BRADY reserves the right to make changes without further notice to any product
or system described herein to improve reliability, function, or design.

© 2016 BRADY Worldwide, Inc. All Rights Reserved

Brady Worldwide Inc.
6555 West Good Hope Road
Milwaukee, WI 53223 U.S.A.
Telephone: [phone] USA Domestic
Facsimile: 414-438-6958

_______________________________________________________________________________

Agency Compliance and Approvals

For Users in the United States

FCC Notice-US Only

This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:

(1) this device may not cause harmful interference,
(2) this device must accept any interference received, including interference that may

cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.

Canada

ICES-003 Class A Notice, Class A

Industry Canada ICES-003: CAN ICES-3 (A)/NMB-3(A)

This device complies with Industry Canada license-exempt RSSs. Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.