Brady B-489 Technical Data

Technical Data Sheet
PHYSICAL PROPERTIES
TEST METHODS
AVERAGE RESULTS
Thickness
ASTM D 1000
-Total (substrate and adhesive)
0.0044 inch (0.112 mm)
Adhesion to:
-Stainless Steel
-Textured ABS
-Polypropylene
-Painted Enamel
-Powder Coated Metal
ASTM D 1000 20 minute dwell 24 hour dwell
20 minute dwell 24 hour dwell
20 minute dwell 24 hour dwell
20 minute dwell 24 hour dwell
20 minute dwell 24 hour dwell
145 oz/in (159 N/100 mm) 146 oz/in (160 N/100 mm)
45 oz/in (49 N/100 mm) 43 oz/in (47 N/100 mm)
80 oz/in (88 N/100 mm)
108 oz/in (119 N/100 mm)
133 oz/in (146 N/100 mm) 142 oz/in (156 N/100 mm)
78 oz/in (86 N/100 mm) 78 oz/in (86 N/100 mm)
Tack
ASTM D 2979 Polyken
TM
Probe Tack
0.5 second dwell
Greater than 35 oz (1000 g)
1
BRADY B-489 THERMAL TRANSFER PRINTABLE LABEL STOCK
TDS No. B-489 Effective Date: 10/03/2006
Description: GENERAL Print Technology: Thermal Transfer Material Type: White Polyester Finish: Matte white Adhesive: Permanent rubber based
APPLICATIONS
B-489 is designed for high adhesion to textured metals and low surface energy plastics
RECOMMENDED RIBBONS
Brady Series R4300 Brady Series R6200 (alternate)
REGULATORY/AGENCY APPROVALS UL: B-489 is a UL Recognized Component to UL 969 Labeling and Marking Standard when printed with Brady Series R4300 and
R6200 ribbons. See UL file MH17154 for specific details. UL information can be accessed online at UL.com. Search in Certifications area.
CSA: B-489 is a CSA Accepted to C22.2 No.0.15-95 Adhesive Labels Standard when printed with the Brady Series R4300 and R6200 ribbons. See CSA file 041833 for specific details. CSA information can be accessed online at
directories.csa-international.org.
Brady B-489 is RoHS compliant to 2005/618/EC MCV amendment to RoHS Directive 2002/95/EC.
SPECIAL FEATURES
B-489 is specifically designed to adhere to powder coated surfaces.
Details:
1
Tacks exceeded the equipment testing range of 1000 grams. Performance properties tested on B-489 printed with alphanumerics,
and a 5 mil and 10 mil minimum X dimension barcode using Series R4300 and R6200 ribbons and a BradyPrinter
TM
THT 300X
Thermal Transfer Printer. Printed samples of B-489 were laminated to aluminum before exposure to the indicated environmental
PERFORMANCE PROPERTIES
TEST METHODS
TYPICAL RESULTS
Long Term High Service Temperature
30 days at 248°F (120°C)
No visible effect
Long Term High Service Temperature
30 days at -40°F (-40°C)
No visible effect
Humidity Resistance
30 days at 100°F (37°C), 95% R.H.
No visible effect
UV Light Resistance
30 days in UV Sunlighter
TM
100
No visible effect
Weatherability
ASTM G155, Cycle 1 30 days in Xenon Arc Weatherometer
No visible effect
Salt Fog Resistance
ASTM B 177 30 days in 5% salt fog solution chamber
No visible effect
Abrasion Resistance
Tabler Abraser, CS-10 grinding wheels, (Fed.Std. 191A, Method 5306) 500g/arm, 100 cycles
Print still legible after 100 cycles
PERFORMANCE PROPERTY
CHEMICAL RESISTANCE
CHEMICAL REAGENT
SUBJECTIVE OBSERVATION OF VISUAL CHANGE
EFFECT LABEL STOCK
R4300
R6200
Methyl Ethyl Ketone
Slight adhesive ooze
Slight smear when rubbed
Severe smear when rubbed
1,1,1-Trichloroethane
No visible effect
Moderate smear when rubbed
Slight smear when rubbed
Toluene
No visible effect
Moderate smear when rubbed
Moderate smear when rubbed
Freon® TMS
No visible effect
Slight smear when rubbed
Moderate smear when rubbed
Isopropyl Alcohol
No visible effect
No visible effect
No visible effect
Mineral Spirits
Slight adhesive ooze
Slight smear when rubbed
No visible effect
JP-8 Jet Fuel
No visible effect
Moderate smear when rubbed
No visible effect
ASTM Reference Fuel B
No visible effect
No visible effect
No visible effect
ASTM #3 Oil
Slight adhesive ooze
No visible effect
No visible effect
Mil 5606 Oil
No visible effect
Slight smear when rubbed
No visible effect
Skydrol® 500B-4
Slight adhesive ooze
No visible effect
Severe smear when rubbed
Super Agitene®
No visible effect
No visible effect
No visible effect
Deionized Water
No visible effect
No visible effect
No visible effect
condition. Results the same for both ribbons unless noted otherwise.
Samples were printed with Series R4300 and R6200 ribbons using a Brady 300X printer, laminated to flat aluminum panels and allowed to dwell 24 hours prior to test. Testing consisted of 5 cycles of 10 minute immersions in the specified chemical followed by 30 minute recovery periods. After the final immersion the flat samples were rubbed 10 times with cotton swabs. Testing was conducted at room temperature.
3% Alconox® Detergent
No visible effect
No visible effect
No visible effect
10% Sodium Hydroxide Solution
No visible effect
No visible effect
No visible effect
10% Sulfuric Acid Solution
No visible effect
No visible effect
No visible effect
Shelf Life:
Two years when stored in its original packaging in an environment below 80°F (27°C) and 60%RH.
Trademarks:
Alconox® is a registered trademark of Alconox Co. BradyPrinter Freon® is a registered trademark of Du Pont de Nemours, E.I. and Company Polyken Skydrol® is a registered trademark of the Monsanto Company Sunlighter Super Agitene® is a registered trademark of Graymills Corporation ASTM: American Society for Testing and Materials (U.S.A.) CSA: Canadian Standards Association SAE: Society of Automotive Engineers (U.S.A.) UL: Underwriters Laboratories Inc. (U.S.A.) All S.I. Units are mathematically derived from U.S. conventional units
Note: All values shown are averages and should not be used for specification purposes. Test data and test results contained in this document are for general information only and shall not be relied upon by Brady customers for designs and specifications, or be relied on as meeting specified performance criteria. Customers desiring to develop specifications or performance criteria for specific product applications should contact Brady for further information.
Product compliance information is based upon information provided by suppliers of the raw materials used by Brady to manufacture this product or based on results of testing using recognized analytical methods performed by a third party, independent laboratory. As such, Brady makes no independent representations or warranties, express or implied, and assumes no liability in connection with the use of this information.
WARRANTY
Brady products are sold with the understanding that the buyers will test them in actual use and determine for themselves their adaptability to their intended uses. Brady warrants to the buyers that its products are free from defects in material and workmanship, but limits its obligation under this warranty to replacement of the product shown to Brady’s satisfaction to have been defective at the time Brady sold it. This warranty does not extend to any persons obtaining the product from the buyers. This warranty is in lieu of any other warranty, express or implied, including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose, and of any other obligations or liability on Brady’s part. Under no circumstances will Brady be liable for any loss, damage, expense, or consequential damages of any kind arising in connection with the use, or inability to use, Brady’s products.
__________________________________________________________________________________________________________________________________
TM
is a trademark of Brady Worldwide, Inc.
TM
is trademark of Testing Machines Inc.
TM
is a trademark of the Test Lab Apparatus Company
Material may not be reproduced or distributed in any form without written permission.
Brady North America 6555 W. Good Hope Road Milwaukee, WI 53223 USA Tel: 414-358-6600 Fax: 800-292-2289
Copyright 2017 Brady Worldwide, Inc. All Rights Reserved
Loading...