Bradley Corporation S19-310TW User Manual
Frost-Proof Drench Shower and Eyewash Unit
•
Complies with American National Standard Z358.1‑2009
•
Wall‑Mounted Unit
•
Galvanized Steel Protected with BradTect® Safety Yellow Coating
•
Universal Identification Sign and Inspection Tag Included
•
Full, One‑Year Warranty
•
Patent Pending
Specifications
Drench Shower and Eyewash Unit is made specifically for areas subject to freezing. This unit
saves space and fits easily into any work environment where outdoor plumbed water source is
not available. Shower and eyewash valves operate quickly by a large, highly visible push handle.
Shower provides a superior washdown with a more even spray pattern. Safe, steady water flow
under varying water supply conditions from 30–90 PSI is assured by integral flow control in the
sprayhead assembly. NOTE: The ANSI Z358.1 standard requires an uninterruptible supply of
flushing fluid at a minimum 30 PSI flowing pressure.
This plumbing fixture is not intended to dispense water for human
consumption through drinking or for preparation of food or beverages.
Model Description
S19-310TW8 Frost‑Proof Drench Shower and Eyewash Unit
S19-310TW12 Frost‑Proof Drench Shower and Eyewash Unit
S19-310TW18 Frost‑Proof Drench Shower and Eyewash Unit
S19-2200 Navigator EFX60 ‑ Emergency Thermostatic Mixing Valve
S19-310TW
Recommended Option:
Navigator S19-2200 EFX60
Emergency Thermostatic Mixing Valve
Satisfies ANSI Z358.1-2009
tepid water requirements.
Page 1 of 3 11/21/2016
This information is subject to change without notice.
Bradley_SafetyCombi_S19-310TW
P.O. Box 309, Menomonee Falls, WI 53052-0309
© 2016 Bradley
800 BRADLEY (800 272 3539) +1 262 251 6000
bradleycorp.com
S19-310TW
Frost-Proof Drench Shower and Eyewash Unit
Standard Equipment
SpinTec™ Showerhead
3.1" (78.7mm) diameter highly visible yellow impact‑resistant plastic. SpinTec drench
showerhead features integral 26 GPM flow control, conserving water and helping to
accurately size your tepid water system.
SpinTec Flow Rate vs Inlet Pressure at Fixture
40
35
30
25
20
15
Flow Rate (gpm)
10
5
0
10 20 30 40 50 60 70 80 90
Inlet pressure at Fixture (psig)
Eyewash Sprayhead Assembly
Chrome‑plated brass sprayhead assembly with twin soft‑flow eyewash heads and
protective sprayhead covers, operated by a large, highly visible stainless steel push
handle. Safe, steady water flow under varying water supply conditions from 30–90 PSI
is assured by integral flow control in the sprayhead assembly.
Frost-Proof Shower and Eyewash Valve (Independent Operation)
Shower has 1" NPT stay‑open valve. Eyewash has ½" NPT stay‑open valve. Hand
operated by a large, highly visible stainless steel push handle.
Pipe and Fittings
Galvanized steel protected with BradTect® safety yellow coating. Standard wall
thickness is 8"– 12". Special order for other wall thicknesses (0"–8" or 12"–18").
Special order depths are non-returnable.
Water Supply
1¼" NPT.
Local codes may require the installation of a backflow prevention valve to
complete proper installation. Compliance with local codes is the responsibility
of the installer. Valve must be tested annually to verify that it is functioning
properly. Backflow prevention valves are not included with the fixture and may
be supplied by the contractor or purchased from Bradley Corporation.
Page 2 of 3 11/21/2016
This information is subject to change without notice.
Bradley_SafetyCombi_S19-310TW
P.O. Box 309, Menomonee Falls, WI 53052-0309
© 2016 Bradley
800 BRADLEY (800 272 3539) +1 262 251 6000
bradleycorp.com
Loading...