Bradley Corporation S19-270C, S19274C User Manual

S19-270C eyewash

douche oculaire

lavador de ojos

Installation

S19-270C, S19-270E,
S19274C, S19274E

Swing-Activated Eyewash and Eye/Face
Wash

Douche oculaire et oculaire/faciale
activée par bras mobile

Lavador de ojos y de ojos/rostro
activado por brazo oscilante

S19-270E eye/face wash

douche oculaire/faciale

lavador de ojos/rostro

S19274C Halo™ eyewash

douche oculaire

lavador de ojos

S19274E Halo™ eye/face wash

douche oculaire/faciale

lavador de ojos/rostro

215-1326 Rev. T; ECN 14-05-009
© 2014 Bradley
Page 1 of 35 6/13/2014

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX [phone]
bradleycorp.com

S19-270C, S19-270E, S19274C, S19274E Installation

Table of Contents

Pre-Installation Information .................................................................. 3

S19-270C, S19274C Dimensions .............................................................4

S19-270E, S19274E Dimensions .............................................................5

Installation .............................................................................6–7

Installation Left-Hand Units ................................................................8–9

S19-270C Assembly of Components and Parts List .............................................. 10

S19274C Assembly of Components and Parts List .............................................. 11

S19-270E Assembly of Components and Parts List .............................................. 12

S19274E Assembly of Components and Parts List............................................... 13

Table des matières

Avant l’installation ........................................................................ 14

S19-270C, S19274C Dimensions ............................................................15

S19-270E, S19274E Dimensions ............................................................16

Installation ........................................................................... 17–18

Installation Gaucher.................................................................... 19–20

S19-270C Assemblage des composantes et liste des pièces....................................... 21

S19274C Assemblage des composantes et liste des pièces ....................................... 22

S19-270E Assemblage des composantes et liste des pièces....................................... 23

S19274E Assemblage des composantes et liste des pièces ....................................... 24

Contenido

Información previa a la instalación ........................................................... 25

S19-270C, S19274C Dimensiones ...........................................................26

S19-270E, S19274E Dimensiones ...........................................................27

Instalación ........................................................................... 28–29

Instalación de Mano Izquierda............................................................ 30–31

S19-270C Armado de los componentes y lista de piezas ......................................... 32

S19274C Armado de los componentes y lista de piezas .......................................... 33

S19-270E Armado de los componentes y lista de piezas.......................................... 34

S19274E Armado de los componentes y lista de piezas .......................................... 35

2

6/13/2014 Bradley • 215-1326 Rev. T; ECN 14-05-009

Installation S19-270C, S19-270E, S19274C, S19274E

IMPORTANT

Installation

R

WI 53051

alls,

HENTLICH ZU
WEEK
WÖC

P.O. Box 309, Menomonee F

DAIRE

e(s) each week and sign

UNIT EACH

y malfunctions immediatel

hentlich im

TEST THIS

hrift. Jeglic

DIESES GERÄT 1ST
ESSAI HEBDOMA

Test-operate valv
Report an

Ventil(e) wöc

t immédiatement.

durch Untersc

Test le fonctionnement des v
signe en bas. S'il y à quelqu

un rappor

Date

Datum
Date

114-051

PRÜFEN.

Testbetrieb prüfen,
he Störung sofor

Signed
Unterschrift

below.

bestätigt
t melden.

y.

alves chaque semaine et
e chose qui ne v

Date Signed

Signe

THIS
SIDE
UP

a pas fait

Signed
Signed

Date
Date

P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA

TEL: 1-800-BRADLEY FAX: [phone])

http://www.bradleycorp.com

Packing List

•

•

•

•

Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes/ordinances is the responsibility of the installer.

Separate parts from packaging and make sure all parts are accounted for
before discarding any packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.

Flush the water supply lines before beginning installation and after installation
is complete. Test the unit for leaks and adequate water flow. Main water supply
to the eyewash should be “ON” at all times. Provisions shall be made to prevent
unauthorized shutoff.

The ANSI Z358.1 standard requires an uninterrupted supply of flushing fluid.
Bradley plumbed emergency fixtures require a minimum of 30 PSI (0.21 MPa)
flowing pressure. Flushing fluid should be tepid per ANSI Z358.1.

The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to ensure
compliance with ANSI Z358.1.

Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment per
ANSI Z358.1.

For questions regarding the operation or installation of this product, visit
bradleycorp.com or call 800.BRADLEY (800.272.3539).

Product warranties may also be found under ”Products” on our web site at
bradleycorp.com.

NOTICE! For classic eye/face wash units, avoid cleaners containing organic solvents, alcohols,
and hydrocarbons. Rinse with water after cleaning.

Supplies Required:

• Piping to ½" NPT water supply inlet on unit

• Pipe sealant

• Inlet strainer (recommended)

• Sign-mounting hardware

Local codes may require the installation of a backflow prevention valve to complete proper installation. Compliance with

local codes is the responsibility of the installer. Valve must be tested annually to verify that it is functioning properly.
Backflow prevention valves are not included with the fixture and may be supplied by the contractor or purchased from
Bradley Corporation.

Bradley • 215-1326 Rev. T; ECN 14-05-009 6/13/2014

3

S19-270C, S19-270E, S19274C, S19274E Installation

Dimensions — S19-270C

3¹⁄₈"

(79mm)

4¹⁄₈"

(105mm)

28-7/8" to 40-7/8"

(733 mm to 1038 mm)

to finished floor

11⁵⁄₈"

(295mm)

(64mm)

2½"

Off

On

(60mm)

Ø ⁷⁄₈"

Ø 2³⁄₈"

(60mm)

2³⁄₈"

Ø ³⁄₁₆"

Ø 1¹⁄₈"

2"

(51mm)

Mounting Pattern

1³⁄₈"

(35mm)

Max.

Dimensions — S19274C

1⁵⁄₈"

(41mm)

2⁷⁄₈"

(73mm)

30-1/8" to 42-1/8"

(765 mm to 1070 mm)

to finished floor

2½"

(64mm)

Off

7¼"

(181mm)

On

Ø 2³⁄₈"

(60mm)

2³⁄₈"

(60mm)

Ø ⁷⁄₈"

Ø ³⁄₁₆"

Ø 1¹⁄₈"

2"

(51mm)

Mounting Pattern

1³⁄₈"

(35mm)

Max.

4

6/13/2014 Bradley • 215-1326 Rev. T; ECN 14-05-009

Installation S19-270C, S19-270E, S19274C, S19274E

Dimensions — S19-270E

3¹⁄₈"

(79mm)

11³⁄₈"

(289mm)

5¾"

(146mm)

27-1/4" to 39-1/4"

(692 mm to 997 mm)

to finished floor

Off

2½"

(64mm)

On

2³⁄₈"

(60mm)

Ø ⁷⁄₈"

Ø 2³⁄₈"

(60mm)

Ø ³⁄₁₆"

Ø 1¹⁄₈"

2"

(51mm)

Mounting Pattern

1³⁄₈"

(35mm)

Max.

Dimensions — S19274E

1⁵⁄₈"

(41mm)

3³⁄₈"

(86mm)

29-5/8" to 41-5/8"

(752 mm to 1057 mm)

to finished floor

Off

11"

(279mm)

2½"

(64mm)

On

Ø 2³⁄₈"

(60mm)

2³⁄₈"

(60mm)

Ø ⁷⁄₈"

Ø ³⁄₁₆"

Ø 1¹⁄₈"

2"

(51mm)

Mounting Pattern

1³⁄₈"

(35mm)

Max.

Bradley • 215-1326 Rev. T; ECN 14-05-009 6/13/2014

5

S19-270C, S19-270E, S19274C, S19274E Installation

Installation — Eyewash

Halo eyewash right-hand unit is shown on a sample 25" deck. Other units are similar. For classic eyewash installation,
refer to the dimensions on page 4 to determine optimal mounting position. Refer to page 8 for left-hand units.

Minimum dimensions necessary to contain splashing from Halo units are shown.

Apply pipe sealant (supplied by installer) to all male-threaded pipe joints. The top of the eyewash heads should be
positioned a minimum of 33" and a maximum of 45" from the floor and 6" from the nearest obstruction.

Proper faucet shank/handle
clearance and recommended
minimum splash containment
dimensions must be considered
when selecting the desired
location for mounting.

25"

(635mm)

A

2"

(51mm)

Ø ³⁄₁₆"

Ø 1¹⁄₈"

Deck Mounting Pattern

(drill (3) holes as shown)

8"

(203mm)

Radius

B

"OFF" Position

5¾"

(146mm)

Ref.

2⁵⁄₈" (67mm)

Ref.

Deck

7¾"

(197mm)

Ref.

5¼"

(133mm)

Min.

"ON" Position

Connect the water supply using
piping (supplied by installer) with

C

½" NPT female threaded end.

(51mm)

Slowly open the water
supply lines to relieve air
and pressurize the valve.

E

Test the unit for leaks

2"

Ref.

¾" (19mm)

Min.

D

To

Wall

114-051

P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA

TEL: 1-800-BRADLEY FAX: [phone])

http://www.bradleycorp.com

and adequate flow.

6

6/13/2014 Bradley • 215-1326 Rev. T; ECN 14-05-009

Installation S19-270C, S19-270E, S19274C, S19274E

Installation — Eye/Face Wash

Halo eye/face wash right-hand unit is shown on a sample 25" deck. Other units are similar. For classic eye/face wash
installation, refer to the dimensions on page 5 to determine optimal mounting position. Refer to page 8 for left-hand units.

Minimum dimensions necessary to contain splashing from Halo units are shown.

Apply pipe sealant (supplied by installer) to all male-threaded pipe joints. The top of the eyewash heads should be positioned
a minimum of 33" (838mm) and a maximum of 45" (1143mm) from the floor and 6" (152mm) from the nearest obstruction.

Proper faucet shank/handle
clearance and recommended
minimum splash containment
dimensions must be considered
when selecting the desired
location for mounting.

25"

(635mm)

13⁷⁄₈"

(352mm)

Radius

A

2"

(51mm)

Ø ³⁄₁₆"

Ø 1¹⁄₈"

Deck Mounting Pattern

Drill (3) holes as shown.

B

Deck

"OFF" Position

13"

(330mm)

Ref.

9¼"

(235mm)

Ref.

"ON" Position

2½"

(64mm)

Min.

Connect the water supply using
piping (supplied by installer) with

C

½" NPT female threaded end.

Slowly open the water
supply lines to relieve air
and pressurize the valve.

E

Test the unit for leaks
and adequate flow.

Bradley • 215-1326 Rev. T; ECN 14-05-009 6/13/2014

5¾"

(146mm)

Ref.

2¹⁄₈"

(54mm)

Min.

D

To

Wall

114-051

P.O. BOX 309, MENOMONEE FALLS, WI 53052-0309 USA

TEL: 1-800-BRADLEY FAX: [phone])

http://www.bradleycorp.com

7

S19-270C, S19-270E, S19274C, S19274E Installation

Installation — Left-Hand Units (Classic)

Classic eyewash unit is shown. Classic eye/face wash unit is similar.

Apply pipe sealant (supplied by installer) to all male-threaded pipe joints.

Rotate the bent arm

B

180° around the valve.

Remove the sprayhead from the
bent arm. Remove the set screw
from the valve assembly with an

A

Allen key (1/16"(1.5mm)). Set
the two items aside.

Rotate the bent arm 180°
around the valve. Using
low strength thread locker,
reinstall the set screw

C

into the valve in the new
location shown until it
bottoms out, then back off
½ turn.

Arm must swing freely.

D

Reattach the sprayhead to the
bent arm, resealing as necessary.

Mount the unit onto the deck. Refer to the instructions on page 6 for
eyewash units or page 7 for eye/face wash units.

E

The left-hand unit must be installed on the left side of the deck.

Slowly open the water supply lines to
relieve air and pressurize the valve. Test

F

the unit for leaks and adequate flow.

8

6/13/2014 Bradley • 215-1326 Rev. T; ECN 14-05-009

Installation S19-270C, S19-270E, S19274C, S19274E

Installation — Left-Hand Units (Halo)

Halo eyewash unit is shown. Halo eye/face wash unit is similar.

Apply pipe sealant (supplied by installer) to all male-threaded pipe joints.

Rotate the
arm 180°

B

around the
valve.

C

Remove the set screw from
the valve assembly with an

A

Allen key (1/16"(1.5mm)) and
set aside.

D

E

Tighten cap assembly,
ensuring head is level.

Using low strength thread locker,
reinstall the set screw into the valve
in the new location shown until it
bottoms out, then back off ½ turn.

Arm must swing freely.

Rotate the head and body 180°
around the arm.

Loosen the cap assembly with
an Allen key (5/16"(8mm)) and
rotate the sprayhead 180°.

Mount the unit onto the deck. Refer to the instructions on page 6 for
eyewash units or page 7 for eye/face wash units.

F

The left-hand unit must be installed on the left side of the deck.

Bradley • 215-1326 Rev. T; ECN 14-05-009 6/13/2014

G

Slowly open the water supply lines to
relieve air and pressurize the valve. Test
the unit for leaks and adequate flow.

9

S19-270C, S19-270E, S19274C, S19274E Installation

Assembly of Components and Parts List — S19-270C

Right-hand swivel version is shown in the "ON" position.

R

P.O. Box 309, Menomonee Falls, WI 53051

TEST THIS UNIT EACH WEEK
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE

Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.

Date

Signed

Date Signed

Datum

Unterschrift

Date

Signed

Date

Signe

Date

Signed

31

bradleycorp.com

114-051

30

23

2

19

Deck

21

1

13

14

15

16

Item Part No. Qty Description

1 S65-385CE 1 Replacement Valve Assembly, Side Swing

Classic Eyewash

2 160-473 2 Screw, Set

13 160-474 2 Screw, Set

14 113-514 1 Shank, ½" x 2½"

15 142-002CB 1 Washer, Flat ⁷⁄₈" x 2"

10

6/13/2014 Bradley • 215-1326 Rev. T; ECN 14-05-009

Item Part No. Qty Description

16 110-115 1 Nut, Brass ½"-14 NPSM

19 113-1032 1 Pipe, Bent Plated

21 S05-092 1 Eyewash Yoke 90°

23 107-371 2 Tethered Dust Cover

30 114-051 1 Safety Sign

31 204-421 1 Emergency Inspection Tag

Installation S19-270C, S19-270E, S19274C, S19274E

Assembly of Components and Parts List — S19274C

Right-hand swivel version is shown in the "ON" position.

R

P.O. Box 309, Menomonee Falls, WI 53051

TEST THIS UNIT EACH WEEK
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE

Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.

Date

Signed

Date Signed

Datum

Unterschrift

Date

Signed

Date

Signe

Date

Signed

31

bradleycorp.com

114-051

30

19

2

Eyewash Cover Prepack
S45-2675 includes items
22 and 23

22

23

22

23

1

21

20

23

27

22

Deck

26

25

13

14

29

15

16

Item Part No. Qty Description

1 S65-385 1 Replacement Valve Assembly, Side Swing

2 160-473 2 Screw, Set

13 160-474 2 Screw, Set

14 113-514 1 Shank, ½" x 2½"

15 142-002CB 1 Washer, Flat ⁷⁄₈" x 2"

16 110-115 1 Nut, Brass ½"-14 NPSM

19 113-1236 1 Pipe, ³⁄₈" x 5½" Chrome Red Brass

20 171-005 1 Body, Mount, Short ³⁄₈" NPT

Item Part No. Qty Description

22 in service kit 2 Pivot Pin

23 in service kit 2 Flip Cover, Eyewash

25 115-169 1 Cap, Short

26 125-157 2 O-Ring

27 125-175 1 Flow Control

29 160-500 1 Screw, Weep

30 114-051 1 Safety Sign

31 204-421 1 Emergency Inspection Tag

21 S05-190 1 Sprayhead Ass'y Eyewash (includes)

Bradley • 215-1326 Rev. T; ECN 14-05-009 6/13/2014

11