![](/html/9d/9d8c/9d8cd357dc7ef2c836c8ee64dc572028e40cf1af3baeb3332d95126a16954c55/bg2.png)
N
G
H
E
L
I
S
FCC Information (For US customers)
1. COMPLIANCE INFORMATION
This equipment complies with Part 15 of the FCC Rules.
Operation is subject to the two following conditions:
(1) this product may not cause harmful interference, and
(2) this product must accept any interference received,
including interference that may cause undesired operation.
FCCID:XN6-MC100BLUE
Boston Acoustics
7 Constitution Way, Woburn, MA 01801 USA
Tel. 978-538-5000
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modification not expressly approved by Boston Acoustics
may void your authority, granted by the FCC, to use the
product.
3. CAUTION
t 5PDPNQMZXJUI'$$3'FYQPTVSFDPNQMJBODF
requirement, separation distance of at least 20 cm must
be maintained between the antenna of this product and
all persons.
t 5IJTQSPEVDUBOEJUTBOUFOOBNVTUOPUCFDPMPDBUFE
or operating in conjunction with any other antenna or
transmitter.
4. NOTE
This product has been tested and found to comply with the
limits for a class B digital device, pursuant to Part 15 of the
FCC Rules. The limits are designed to provide reasonable
protection against harmful interference in a residential
installation.
This product generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment OFF and ON, the user
is encouraged to try to correct the interference by one or
more of the following measures:
t 3FPSJFOUPSSFMPDBUFUIFSFDFJWJOHBOUFOOB
t *ODSFBTFUIFTFQBSBUJPOCFUXFFOUIFFRVJQNFOUBOE
receiver.
t $POOFDUUIFFRVJQNFOUUPBOPVUMFUPOBDJSDVJU
different from that to which the receiver is connected.
t $POTVMUUIFEFBMFSPSBOFYQFSJFODFESBEJPPSUFMFWJTJPO
technician for help.
IC Information (For Canadian customers)
1. PRODUCT
This product contains IC 8819A-MC100BLUE.
This Class B digital apparatus complies with Canadian
ICES-003.
2. CAUTION
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that permitted for successful communication.
This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter
may only operate using an antenna of a type and maximum
(or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le
présent émetteur radio peut fonctionner avec une antenne
d’un type et d’un gain maximal (ou inférieur) approuvé pour
l’émetteur par Industrie Canada. Dans le but de réduire les
risques de brouillage radioélectrique à l’intention des autres
utilisateurs, il faut choisir le type d’antenne et son gain de
sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.)
ne dépasse pas l’intensité nécessaire à l’établissement d’une
communication satisfaisante.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Informations sur IC (pour les clients canadiens)
1. APPAREIL
Cet appareil contiens IC 8819A-MC100BLUE.
Cet appareil numérique de las classe B est conforme à la
norme NMB-003 du Canada.
2. ATTENTION
Afin de réduire le risque d´interférence aux autres utilisateurs,
il faut choisir le type d´antenne et son gain de façon à ce
que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
soit pas supérieure au niveau requis pour l´obtention d´une
communication satisfaisante.
Designed in USA
Made in China
Boston Acoustics, Inc., USA
2
![](/html/9d/9d8c/9d8cd357dc7ef2c836c8ee64dc572028e40cf1af3baeb3332d95126a16954c55/bg3.png)
This symbol found on the apparatus indicates hazards
arising from dangerous voltages.
This symbol found on the apparatus indicates the user
should read all safety statements found in the user manual.
This symbol found on the apparatus indicates
double insulation.
Warning!
To reduce the risk of fire or electrical shock, do not
expose this apparatus to rain or moisture.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the
other. A grounding-type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit
from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for
long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
14. Maintain a minimum distance of 2" (50mm) around the front, rear,
and sides of the apparatus for sufficient ventilation. The ventilation
should not be impeded by covering the ventilation openings or
placing on or around the apparatus items such as newspapers,
table-cloths, curtains, etc.
15. No open flame sources, such as lighted candles, should be
placed on the apparatus.
16. The apparatus shall not be exposed to dripping or splashing.
No objects filled
the apparatus.
17. Either the power inlet connector on the rear of the apparatus or
the power plug at the wall must remain accessible, to be able to
disconnect power from the apparatus.
18.
To completely disconnect this apparatus from the AC Mains,
disconnect the power supply cord plug from the AC receptacle.
Use only with the cart, stand, tripod, bracket,
19.
or table specified by the manufacturer, or sold
with the apparatus. When a cart or rack
is used, use caution when moving the
cart/apparatus combination to avoid injury
from tip-over.
CAUTION: These servicing instructions are for use by qualified
20.
service personnel only. To reduce the risk of electric shock, do not
perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
WARNING: Only use attachments/accessories specified or
21.
provided by the manufacturer
WARNING:Please refer the information on exterior bottom
22.
enclosure for electrical and safety information before installing
or operating the apparatus.
When not in use and during movement, please take care of the
23.
power cordset, e.g. tie up the power cordset with cable tie or
something like that. It shall be free from sharp edges that can
cause abrasion of the power cordset. When put into
use again, please make sure the power cordset is not damaged,
If any damage is found, please contact customer service and
replace the power cordset.
with liquids, such as vases, shall be placed on
Warning: To reduce the risk of electric shock, do not remove cover
24.
(or back) as there are no user-serviceable parts inside. Refer
servicing to qualified personnel.
Observe and follow local regulations regarding battery disposal.
25.
Do not keep the battery in a place exposed to direct sunlight or
in places with extremely high temperatures, such as near a heater.
WARNING:
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
7KHUHPRWHFRQWUROVXSSOLHGZLWKWKLVSURGXFWFRQWDLQVDFRLQ
button cell battery. If the coin/button cell battery is swallowed, it
can cause internal burns in just 2 hours and can lead to death.
.HHSQHZDQGXVHGEDWWHULHVDZD\IURPFKLOGUHQ,IWKHEDWWery
compartment does not close securely, stop using the product
and keep it away from children. If you think batteries might have
been swallowed or placed inside any part of the body, seek
immediate Medical attention.
2EVHUYHDQGIROORZORFDOUHJXODWLRQVUHJDUGLQJEDWWHU\GLVSRsal.
'RQRWNHHSWKHEDWWHU\LQDSODFHH[SRVHGWRGLUHFWVXQOLJKW or
in places with extremely high temperatures, such as near a heater.
American Users:
Note:This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution: Unauthorized changes or modifications to the receiver could
void the user s authority to operate the equipment.
Canadian Users:
This class B digital apparatus complies with CAN ICES-3(B). Cet appareil
numérique de classe B est conforme á la norme NMB-3(B) du Canada.
FCC Radiation Exposure Statement
1)This equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter. This equipment
should be installed and operated with a minimum distance of 20 centimeters
between the radiator and your body.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
2)the IC statement of the user manual is not correct, attached the correct IC
statement for your reference. please update the user manual.
Canada
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la
section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf,
utilisateurs peut obtenir l'information canadienne sur l'exposition et la
conformité de rf.
E
N
G
L
I
S
H
3
![](/html/9d/9d8c/9d8cd357dc7ef2c836c8ee64dc572028e40cf1af3baeb3332d95126a16954c55/bg4.png)
N
G
H
E
L
I
S
Introduction
Thank you for choosing Boston Acoustics® and congratulations on your purchase of the MC100 Blue
wireless speaker system. The MC100 Blue is a self-amplified stereo speaker system that uses Bluetooth®
wireless communication to receive a signal from any standard Bluetooth equipped device capable of
stereo audio transmission (A2DP).
Using the simple controls on the MC100 Blue, and its remote control, you can adjust the volume of the
system or operate the basic music play back functions of your connected devices. An auxiliary analog
input also allows you to connect any music source that has a standard 3.5mm connector to the MC100
Blue. We hope you’ll enjoy it for years to come.
Features
t 0VUTUBOEJOHTUFSFPQFSGPSNBODFGSPNEVBMIJHIQFSGPSNBODF#PTUPOEFTJHOFEJODITQFBLFST
in separate acoustic chambers, vented for extended bass response
t #MVFUPPUIXJSFMFTTTUSFBNJOHGSPNBOZDPNQBUJCMF#MVFUPPUINVTJDQMBZFSQIPOFUBCMFUPS
computer
t 5BQUPQBJSGVODUJPOBMJUZGPSJOTUBOUDPOOFDUJPOXJUIBOZEFWJDFUIBUTVQQPSUT/FBS'JFME
Communication (NFC)
t "QU9DPEFDGPS$%MJLFTPVOERVBMJUZPWFS#MVFUPPUI
t "VYJMJBSZJOQVU
t #BTT5SBD¥BVEJPQSPDFTTJOHGPSTBUJTGZJOHCBTTBUBOZWPMVNF
t &BTZUPVTFDPOUSPMT
t 7PMVNFMFWFMEJTQMBZCFIJOEHSJMMF
t 3FNPUFDPOUSPMXJUINVTJDQMBZCBDLDPOUSPMT
t )FBEQIPOFPVUQVU
t &MFHBOUTUZMJOHXJUICFBVUJGVMIJHIHMPTTmOJTI
Unpacking and Setting Up Your MC100 Blue
Carefully unpack the system. If there is any sign of damage from transit, report it immediately to your
dealer and/or delivery service. Keep the shipping carton and packing materials for future use. Be sure to
keep your purchase receipt in a safe place, as it may be required for warranty purposes.
In the carton you should nd the MC100Blue, remote control, power supply and a power plug adapter.
Placement
Your MC100 Blue will sound great just about anywhere. If you put it near a wall or corner the bass
response will be enhanced. Blocking the bass ports on the rear of the cabinet will reduce bass response.
4