Boss BV8972 User Manual

Page 1

Page 2

Precaution

THANK YOU FOR PURCHASING PLAYER .

Before operating the unit, read this manual thoroughly and keep it handy for future reference . To avoid injury or accident , read the following precautions before installing and operating the unit .

A BOSS AUDIO MULTIMEDIA

ABOUT THE LIQUID CRYSTAL DISPLAY (LCD) PANEL

Do not press on the LCD panel on the unit as doing so can distort the picture or cause a malfunction . The picture may become unclear , or the LCD panel may be damaged .

NOTES ON CLEANING

-Clean the LCD panel with a slightly damp soft cloth.

-Do not use solvents such as benzine, thinner, commercially available cleaners or antistatic spray .

- Do not use alcohol to clean the screen .

If your car was parked in a cold or hot place, the picture may not be clear . The monitor is not damaged . The picture will become clear the temper ature in your car becomes normal .

DO NOT install any receiver in locations where;

- it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.

- it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident.

- it may obstruct visibility. DO NOT operate any receiver while manipulating the steering wheel, as this may result in a traffic accident. The driver must not watch the monitor while driving. IF THE DRIVER watches the monitor while driving, it may lead to carelessness and cause an accident. IF YOU NEED to operate the receive while driving, be sure to look ahead carefully or you may be involved in a traffic accident. IF THE PARKING BRAKE is not engaged.“ ParkingBrake” flashes on the monitor, and no playback picture will be shown.

- This warning appears only when the parking brake wire is connected to the parking brake system built in the car ( refer to the electric connection)

ON INSTALLATION

Page 3

Safety Information

CAUTION:

THIS DIGITAL VIDEO PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DIGITAL VIDEO PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE . HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DIGITAL VIDEO PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.

THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.Use of this copyright protection technology must be authorized by Macro vision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

REGION MANAGEMENT INFORMATION:

This Digital Video Player is designed and manufactured to respond to the Region Management Information that is recorded on a Digital Video disc. If the Region number described on the Digital Video disc does not correspond to the Region number of this Digital Video Player, this Digital Video Player cannot play this disc.

Page 4

Disc Note

Preparing New Discs with Rough Spots

A new disc may h a ve ro ugh e dges o n its insid e and outsi de ed ges. I f a disc with ro ugh ed ges i s use d , the prop er setting w ill n ot be perf o rmed and t h e player will n ot play the disc. The refore, remove the rough edges i n advance by using a ball point pen or pencil as shown on the right. To remove the rough edges, press the s i de o f t he pen or pencil against the inside and outside edges of the disc.

ough spo ts on outsid e edge

Ball poi nt pen or penci l

Rough sp ots

on insid e

edge

Do not to uch the under side of the di sc

Do not bend

Wipe th e dis c from cente r towar d the outsid e edge

Label s ide up

Disc Cleaning

Use a dry soft cloth to wipe the surface. If the disc is quite dirty, use a soft cloth slightly moistured with isopropyl (rubbing) alcohol. Never use solvents such as benzine, thinner or conventional record cleaners as they may mar the surface of the disc.

Handling and Cleaning

Dirt, dust, scratches and warping disc will cause misoperation. Do not place stickers or make scratches on discs. Do not warp discs. A disc should always be kept in its case when not in use to prevent from damaging. Do not place discs in the following places:

1.Direct sunlight

2.Dirty, dusty and damp areas

3.Near car heaters

4.On the seats or dashboard

Discs which cannot be played with this player

Digital Video-RAM CDV CDG

Note:

A disc may become somewhat scratched (although not enough to make it

unusable) depending on your handle it and conditions in the usage environment.

Note these scratches are not an indication of any problem with the player.

Disc formats supported by this player

Digital Video

VCD

MP3

Audio and Video Disc size 12 cm

Audio Disc size 12 cm

Page 5

Installation

NOTES:

1. Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

2. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.

3. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

4. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

5. Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

. Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

7. If installation angle exceeds 30 from horizontal, the unit might not give its optimum performance.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either from "Front"(conventional DIN Front-mount) or "Rear"(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

Removing the unit

1. Press the REL button to release the front panel .

2. Remove the control panel .

Page 6

Installation

Installation the unit

3. Remove the PLASTIC COVER of the both sides away

4. Insert the two KEY PLAT into the grooves at both sides of the unit as shown in figure until they click .

PLASTIC COVER

KEY PLATE

5. Pulling the levers makes it possible to remove the unit from the dashboard .

ASH BOARD

METAL MO UNTING STRAP

EX NUT

PRING WASHER

PLAIN WASHER

TAPPING SCREW

ONSOLE

LIDE BRACKET

HOUSING

EX BOLT

Page 7

Installation

How To Remove And Install The Front Panel

When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder.

2). Pull-off the front panel and keep the front panel into the case .

Detaching Control Panel

Before detaching the control panel, be sure to turn off the power.

1). Press the “REL” release button and the left hand side of front panel will release.

Attaching Control Panel

1). First insert the right hand side of the front panel into the hollow of the unit . (NOTE : the “bulge” point on the panel must be attached into the hollow of the unit .)

2). Gently push the left hand side of the front panel until you feel a “ Click” .

ROTECTIVE CASE

Hollow

Bulge

ELEASE BUTTON

Page 8

Installation

Caution:

Do not insert your finger behind the control panel.

ANGLE 1 ANGLE 2

ANGLE 3ANGLE 4

When you want to change the viewing angle of the operating unit to play, you can touch the section on touch screen (or press the button on the ) repeatedly to select the desired angle as follows:

ANGLE 1 - ANGLE 2 - ANGLE 3 - ANGLE 4 - ANGLE 1 .

remote

CHANGING THE CONTROL PANEL ANGLE

Page 9

Electric Connection

WIRING CONNECTION

Note:

the ground connection cable (parking brake B-) must be connected in order for pictures to be played back to the monitor. If the cable has not been correctly connected, appears on the monitor. warning message

(B+)12V REAR CAMERA SW ITCH

(B-)PARKING BRAKE

GREY

GREY/BLACK

FRONT RCH SPK.

VIOLET

VIOLET/BLACK

WHITE

WHITE/ BLA CK

GREEN

GREEN/BLA CK

REAR

LCH SPK.

AUTO ANTENNA

BLUE/WHI TE

GROUND(B- )

MEMORY BACK-UP (B+)

IGNITION SWITCH(B+ )

RED

YELLOW

BLACK

REAR RCH SPK.

FRONT

LCH SPK.

LIGHT GREEN

FUSE

KEY GROUND(BLACK ) KEY 1(BROWN) KEY 2(WHITE)

VIOLET/WHIT E

SUBWOOFER GREY

RCH RED

LCH WHITE

REAR OU TPU T CABLE

FRONT RCA WHITE L

FRONT RCA RED R

VIDEO OUT YELLOW

FRONT RC A OUTP UT CABLE

REAR CAMERA IN PUT YELLO W

RADIO ANTENNA JACK

RCH IN RED

LCH IN WHITE

VIDEO OUT(2) YELLO W

VIDEO IN YELLOW

AV IN

Page 10

Remote Control

Button

Ref #

Function

OSD

In media Playback modes, Press this button to see information about the media currently in play.

PROG

Pres s it to pr og ram media pl ay mod e , refer to see PROG operat ion.

LOUD Press to switch the LOUDNESS function ON and OFF .

(0~9) BUTTONS

Use to input numerical values during programming, with the GOTObutton, or to directly select a track to play .

MO/ST (ANGLE)

In Radio mode, press this button to change between Mono and Stereo reception modes (when a station is weak, sometimes switching to Mono will improve sound quality). For Digital Video

media which have alternate viewing angles encoded, when you see the "angle mark" symbol advising you that these angles are available.

CLK

Press it briefly to view the clock time , Press again to return to normal display mode .

LOC/ SLOW

In Radio mode, press this button to change the radio reception sensitivity in stations are near or far. In media mode, press to execute the slow forward function.

Page 11

Remote Control

Button

Ref #

Function

9&24

SEL

Press these buttons to skip ahead or back one track.

In media Playback mode, press for fast forward playback.

In media mode, press it to reverse rapidly

VOL+/-

STEP

Use these controls to adjust the volume level.

BAND

INT

RPT

LANG/ L/R/ST

A-B/ CLEAR

10+ BUTTON

In Radio mode, press this button repeatedly to switch between the five radio bands: FM1 > FM2 > FM3 > AM1(MW1) > AM2 (MW2).

SRC

Press it briefly to select DISC, RADIO , AUX IN , etc .

MUTE

Press this button to turn off the audio. Press again to restore the sound to its prior volume level.

STOP

Press once to pause playback. Press PLAY/PAUSE to resume playback.

SKIP

In video mode, press the STEP button consecutively to display still frame step by step.

This button is used to confirm selection.

Please see INT operation in basic operation part.

Please see RPT operation in basic operation part.

Press it button to change the viewing angle of the operate unit .

This button is used with the other number buttons for use with two-digit number entries.

In Radio mode, press this button to change between Mono and Stereo reception modes (when a station is weak, sometimes switching to Mono will improve sound quality). In Digital Video Playback mode, pressing this button opens the AUDIO setup menu for making changes to the way the soundtrack is reproduced.

Please see A-B Repeat operation.

PLAY/ PAUSE

ZOOM

In media Playback mode, press to pause playback. Press again to start where playback stopped.

Press to increase the picture in size .

Press repeatedly to cycle through the different equalizer curve presets you may wish to use for enhanced listening.

SUBT

Please see subtitle operation.

Press the SEL to

switch between BASS,TREBLE,BALANCE, FADE,

SWF VOL and SWF FRE.

After switching on the desired mode above, rotate VOL knob or

press VOL+/VOL- buttons to set it.

Page 12

Remote Control

Using the Remote Control

Face the remote control towards the player front face IR mark (remote control signal

receiver).

Operation angle: About 30 degree in each the direction of the front of the IR mark.

Preparing the Remote Control

1.First push to inside as the direction indicated by the arrow (See )And then

Remove the battery holder as the direction indicated by the arrow (See ).

2.Replace the battery Set a new battery property with (+)side up as illustrated

(See ).

3.Insert the battery holder. Push in the holder to the original position(See ).

Inserting the Battery

Note :

The lithium cell in the battery compartment of remote control has been secured for

transport with a plastic . Before initial use please remove this plastic so that the remote

control is ready for operation .

Button

Ref #

Function

APS

POWER

Press this button to turn the unit ON , press and hold to turn the unit OFF.

In Radio mode, press and hold this button to start the Auto-Program mode, during which the tuner will scan for all strong stations and assign them to the radio preset buttons.

Press this button briefly to display the root level directory of a Digital Video media.

SETUP

RDM

GOTO

PBC/ TITLE

Press this button to open the SETUP menu.

/ / /

Press to navigate the various menus present in the product.

In Digital Video play mode, for TITLE menu ; in VCD play mode, press this button to create a PBC (Playback Control) menu; please see the Title Menu function.

Please see RDM operation in basic operation part.

Please see GOTO operation.

Page 13

Basic Operation

ADJUSTABLE ITEMS:

ANIMATION

In RADIO mode, you can change the playing time of animation among of “OFF, 10S, 30S, 1M,90S, 2M, 3M and 4M ”.

Note:

Please set the playing time of the animation to “ 10S ” for the first, when you turn the unit on .

KEY BEEP : ON or OFF.

GEN ERAL

ANI MATION 2 M INUTE

KEY B EEP ON

DIS C ...DIS C ...

RAD IO ...

General setup interface1

General setup interface2

GEN ERAL

WALL PAPER ...

ABO UT ...

Main Menu Operation

In many modes, touch the icon or touch the range to enter the main menu, the message like following as below.

Touch the “ ” section on the setting menu, touch the “ / ” ranges to select the adjustment item, Touch the “ ” icon to return to the previous playback .

Setup interface 1

1. POWER icon In any modes, touch the POWER icon to switch the unit off . The monitor will draw in automatically .

2. UP/DOWN icon Touch this icon to adjust the angle of the monitor upward or downward until your desired angle .

3. EJECT icon Touch to allow for inserting or ejecting disc.

4. When the unit is power on, tap this icon that the display turn dark,tap twice turn dark more, tap thrice to turn off the display, and tap anywhere of the display to turn it on again.

5. SETUP icon Touch to enter the SETTING mode, the message will display as follow :

10:00 AM10:00 AM

(3)(1) (2) (5)

(4)

Setup interface 2

ILL UMINATI ON COLO R

Page 14

Basic Operation

FORMAT

TV TYPE

This is to select the appropriate TV aspect (4:3 or 16:9) according to the connected TV set.

Normal/PS (For 4:3 TV)

Played back in the PAN & SCAN style. (If connected to wide-screen TV, the left and right edges are cut off.)

Normal/LB (For 4:3 TV)

Played back in LETTER BOX style. (If connected to wide-screen TV, black bands appear at top and bottom of the screen.)

Wide (For 16:9 TV)

Select when a wide-screen TV set is connected.

RATING

Select to turn Parental Control on or off.

This player is capable of playing discs recorded in either PAL or NTSC formats. Make the selection based on whether you are connecting the unit to a PAL TV or an NTSC TV. You can also set the unit to AUTO (auto select). The disadvantage to autoselect is that each time you turn the unit on it checks to see what kind of monitor is connected, which causes a small delay and some flickering of the display image which you may find unpleasant.

The factory default password is 0000.

16:9

4:3 Letter Box

4:3 Pan Scan

changes to the Parental Control menu below .)

Key in “0000” and then turn to rating then you can setting as follow: KID SAFE -> G -> PG -> PG-13

-> PG R -> R ->NC-17 -> ADULT

RADIO

ST/MONO: touch to select stereo or mono.

LOCAL: touch to select local or distant.

REGION: touch to select radio frequency.

WALLPAPER

Touch to select wallpaper .

ABOUT

Touch to show the version information.

CLOCK SETUP

Touch the CLOCK to adjust the time and time format.

AUDIO SETUP

Touch the audio to turn to audio quality adjustment.

(The password must be used to make

clock setup interface

audio setup interfa ce2audio setup interfa ce1

Disc setup as follow:

DIS C

FOR MAT AUTO

TV TY PE 16:9

RATIN G ADULT

Page 15

Basic Operation

RESET

TREBLE: -7 to +7 Adjust treble level .

BASS: -7 to +7 Adjust bass level .

SUBWOOFER: touch to adjust subwoofer volume and frequency.

EQ: touch to select audio mode as follow:

USER -> JAZZ -> CLASSIC -> POP -> ROCK

LOUDNESS: touch to select loudness effect as :OFF -> LOW -> MID -> HIGH

FADER/BALANCE: BALANCE: R 0-10 to L 0-10

Adjust sound balance between left and right speakers .

FADE: F 0-10 to R 0-10 Adjust sound balance between front and rear speakers .

VIDEO SETUP

COLOR: -20 to 20

Adjust the color for the picture-lighter or darker.

BRIGHTNESS: -20 to 20

Adjust if the picture is too bright or too dark.

CONTRAST: -20 to 20

Adjust the contrast of the bright and dark portion.

TINT: -20 to 20

Adjust the tint if the human skin color is unnatural.

-Adjustable when “NTSC “ is selected for “NTSC/PAL “ .

LANGUAGE

Touch to select OSD language.

ILLUMINATION COLOR

Touch to select the backlight for all buttons. Tap auto icon the backlight change automatically.

CALIBRATION

Touch the arrow as show to calibration the display.

NOTE:

If RESET is selected, all memory data will deleted, please re-adjust .

Rear View Camera

When connecting the rear view camera the mirror image of the rear view is automatically displayed on the monitor when you change the gear to the back position. (Note: additional monitor can not display the image.)

Reset Factory Settings

RESET button is placed on the housing and must be activated with either a ballpoint pen or thin metal object. The RESET button is to be activated for the following reasons:

A. Initial installation of the unit when all wiring is completed. B. All the function buttons do not operate. C. Error symbol on the display.

Video setup interface

Page 16

UNIT KEYS

Control Panel

57 6 8 9

410

ontrol Panel

liding Plate diagram after remo ving Control Panel

1. AUXILIARY INPUT JACK

Insert an external device to this AUX jack in order to have audio output of the device through the unit.

3&4. VOL+/ VOL- BUTTON

In normal mode, these two buttons are used to increase or decrease the volume. And also used as an UP/DOWN knob when audio or video settings are being adjusted when accessed using the SELECT button.

2. IR sensor

Page 17

Control Panel

5. /SRC BUTTON

In power off mode, press it to turn on the unit.

In power on mode, short press it repeatedly to select one mode of the RADIO, DISC, USB, CARD, AUX and AV; long p to turn off the unit.ress it

6/7. >>| and |<< BUTTONS

In radio mode,

For information about connecting a USB device, please see USB operation.

RESET BUTTON

Press this button to return to factory settings.

SD CARD SLOT

long pressing |<< or >>| button can automatically search down or up for an available station beginning from the current frequency; Briefly pressing |<< or >>| button can manually search down or up for a your desired station beginning from the current frequency.

In media mode, pressing |<< or >>| button can play the previous or next track; continuously and long pressing |<< or >>| button can fast backwards or forwards at the following multiple of normal speed: x2, x4, x8, x20.

. MUTE BUTTON

Press it button to switch of the loudspeakers for a short period. The word MUTE flashes in the display. Press it again to cancel the mute function. This function can also be cancelled by rotating the VOL multifunction button.

9. OPEN BUTTON

Press to eject a disc.

10. USB PORT

11. REL BUTTON

Press it to detachable the front panel.

12.

13.

Page 18

Touch Screen Operation

10:00 AM10:00 AM

Briefly touch “ ” to decrease frequency by one step of channel spacing.

Automatic Search

During Radio mode, touch and hold (for more than 2 seconds ) either “ / ” ICONS to start search for a radio station automatically.

To tune in strong-signal FM Station only (LO/DX function)

Press button on the

remote control to select

mode of Local and

Long-distance traffic news.

Storing and Listening to a Memory Station

Setting Memory

With this system, a total of 30 stations can be stored in the memory of six buttons. Each band stores up to six preset stations. The stations might be FM1, FM2, FM3, AM1(MW1), and AM2(MW2) band. The operation is as below :

- Store in Memory >Select the frequency band

>Select the station >Press and the station until it show

the frequency band your select.

- Retrieve a preset station Touch the 1-6 ranges briefly to retrieve

a station which had been stored in the memory in advance the chose number is shown on display .

In radio mode, LOC

or tap icon

select LOC/DX

Selecting The Frequency Band

Touch the screen of “ BAND ” section repeatedly to select the band , the message will show in turn :

When an FM stereo broadcast is hard to receive

Press ST/MO button on the remote control to select the MONO or STEREO mode .

Start Searching For a Station

Manual Search

During Radio mode, briefly touch “ ” to increase frequency by one step of channel spacing.

M1 FM2 FM3

AM2(MW2)

AM1(MW1)

RADIO OPERATION

Touch the RADIO ICON in home menu to enter the RADIO mode. In radio mode, tap icon that the display turn dark, tap twice turn dark more, tap thrice to turn off the display, and tap anywhere of the display to turn it on again.

Listening to Radio

87.50 101.70 98.10

107.9 100.8

87.50

Page 19

Touch Screen Operation

Automatic Memory Storing & Program Scanning

Automatic Preset Setup

In Radio Mode, touch and keep (for more than 2 ’ S) the screen of “ ” range to active automatic station storage. The radio searches within the current frequency band, e.g. Fm , for the stronger signal level until the search cycle has finished . The six strongest stations are then allocated to the corresponding storage locations . Then the station of the first storage location is set .

Scan Function

In Radio mode, briefly touch the “ ” section on the touch screen , the radio briefly plays all the preset stations of the frequency band .

- Store in Memory >Select the frequency band

>Select the station >Press and the station until it show

the frequency band your select.

- Retrieve a preset station Touch the 1-6 ranges briefly to retrieve

a station which had been stored in the memory in advance the chose number is shown on display .

Page 20

Media Operation

In audio play mode, the message will display as below : (When Parking Brake is applied .)

Touch Screen Operation

The icons for other mode

(The same icon have the same function in each mode)

In PHOTO playing ,tap to change the photo direction.

ZOOM IN and OUT.

For page turning.

Mute function

To select the Equalizer mode

Fast forward

Fast backward

Intro Function

To decrease the volume level

To increase the volume level

Loudness Function

Subwoofer Function

Play/Pause the playing

To skip the next track

To skip the previous track

Repeat Function

Random Function

Previous menu

In audio play mode, tap icon that the display turn dark,tap twice turn dark

more, tap thrice to turn off the display, and tap anywhere of the display to turn it on again.

Page 21

Touch Screen Operation

EPEAT ALL

HAPTER REP EAT ON TITL E REP EAT O N

EPEAT OFF

Note:

when the JPEG disc playback, in normal mode, you can use the cursor buttons to rotate the picture . Press UP to invert an image . Press DOWN to mirror an image . Press LEFT to rotate an image to left . Press RIGHT to rotate an image to right .

FOR CD :

Tap the icon or press the INT button on the remote control to play the previous 10 seconds part of each track/chapter on disc. (Touch it again to cancel this mode)

EPEAT OFF

EPEAT ONE REPEAT ALL

EPEAT ALL

EPEAT ONE REP EAT FO LDER(or DI R)

EPEAT OFF

SELECTING PLAY MODES

During the Disc playback, select the “RPT, RDM, INT ” to select your favour play mode.

2). INTRO FUNCTION

Note :

For some VCD2.0 disc (PBC-playback control), above these buttons may be unavailable .

Skipping Track

During DISC playback, Touch the / section on the touch screen to skip to next/back one track.

Digital Video/VCD/CD/MP3:

ormal Pla yback 2 x 4x 8x 20x

Rapid Forward/Rapid Reverse

During DISC playback, touch the screen of “ / ” range the speed of rapid forward/reverse changes according to the disc as follow:

Use the direction keys ( / / / on remote control to move the enlarged picture .

Zoom Function

Touch the button repeatedly, the displayshow as “zoom 2,

zoom 3, zoom 4 , zoom ½, zoom 1/3, zoom 1/4 , zoom off . ”

Pause (still picture)

Touch the “ ” section on touch screen during playback will stop play temporary, touch it again to return the normal playback .

BASIC OPERATION

FOR Digital Video :

Tap the icon or press the RPT button on the remote control to select REPEAT mode as follows :

1). REPEAT FUNCTION

FOR VCD/CD :

Tap the icon or press the RPT button on the remote control to select REPEAT mode as follows :

FOR MP3 :

Tap the icon or press the RPT button on the remote control) to select REPEAT mode as follows :

Page 22

Touch Screen Operation

Note: when select the INTRO Mode, this player to start to play the previous 15 seconds part of each track/chapter on disc. (Touch it again to cancel this mode .)

3). RDM(RANDOM) FUNCTION

During DISC playback, touch screen of “ ” section ( press the RDM button on the remote control to play in random. Each play mode the order is different . (Depend on the disc used for VCD). Touch it again to cancel this function .

FOR VCD :

Press the INT button on the remote control. It display will following menu as below :

FOR Digital Video/MP3 :

For Digital Video/MP3 , press the INT button is not available .

EQ PLAY INTRO 1

OSD

2. Example for VCD/SVCD, when it is on, it will display the information such as:

3. Example for Movie or PHOTO . When it is on, it will display the information such as:

DISC Search (GOTO)

FOR Digital Video :

Touch the screen as show or press the GOTO button on remote control;

the screen will display the following message :

Touch the to select the your adjustment item, then select the item your favour by touching the numberic buttons , then touch the OK button to confirm .

T 001 /004

C 001 /001

Note : in random mode, the button

is not available .

During playback, touch the screen or press the OSD on the remote control, it will display the following as below :

Note: touch the screen or press the OSD on the remote control again to cancel the OSD information.

1. Digital Video , when it is on, it will display the information such as:

ON-SCREEN DISPLAY FUNCTION

Page 23

Touch Screen Operation

the screen will display the following message :

Touch the to select the your adjustment item, then select the item your favour by touching the numberic buttons , then touch the OK button to confirm .

For Movie/Photo:

Touch the screen as show or press the GOTO button on remote control;

the screen will display the following message :

Touch the to select the your adjustment item, then select the item your favour by touching the numberic buttons , then touch the OK button to confirm .

FOR VCD (With PBC OFF) :

Touch the screen as show or press the GOTO button on remote control;

Page 24

Touch Screen Operation

Digital Video Special Function

4. Title Menu Function

For Digital Video:

If the Digital Video has multiple titles recorded on the disc. It can select preferred title from the title menu to start playback.

- During Digital Video playback, press TITLE button on the remote .The title menu is display.

- Select preferred title by the cursor button and confirmed by press the ENTER button .

For VCD:

Press TITLE/PBC button on the remote control while the disc is playing, you can switch between "PBC ON"and "PBC off" mode.

MONO LE FT MONO RIGH T

STERE O

MIX-M ONO

For VCD/CD:

during playback, touch the AUDIO

section of the touch screen or Press AUDIO on the remote . It is possible to switch the sound between monaural and stereo sound.

2. Multi-Audio Language Function

For Digital Video:

During Digital Video playback , touch the icon on touch screen (or press the LANG

on the remote .) Each time the button is pressed or touch , number of the audio soundtrack language changes on sequential order.

Notes:

- The language number is different according to the disc.

- Some disc only contain one language soundtrack

- When no different language soundtra ck are recorded will be display at screen left top corner.

“ INVALID KEY ”

Notes:

- The language number is different according to the disc.

- Some discs only contain one subtitle language.

- When no different subtitle language are recorded, “ INVALID KEY ” will be displayed at screen left top corner.

During Digital Video playback. Touch the icon on touch screen(or press the SUBT on the remote) .

1. Multi-subtitle Language Function (for Digital Video Only)

Each time the button is pressed or touch,

number of the subtitle language changes

in sequential order.

During Digital Video playback, touch the icon on the touch screen . Each time the button is pressed , the number of the angel changes in sequential order .

Notes:

- The angle number is different according to the disc.

- The function only work for disc having scenes recorded at different angles.

- When no different angle are recorded, will be displayed at

screen left top corner.

“ INVALID KEY ”

3. Multi-Angle Function (for Digital Video Only)

Page 25

Touch Screen Operation

5. A-B Repeat

(for Digital Video and VCD)

Press the A-B button if you want to

repeat a specific segment on a disc

that you define:

1. Press the A-B button at a point (A)

where you want it to be the start point

of the repeat segment. Press the A-B

button again at a point (B) where you

want it to be the terminal point of the

repeat segment. Then it will play the

segment repeatedly.

2. To cancel the A-B repeat mode and

resume normal playback, press the A-B

button for the third time.

Note:

During DVD playback, points A and B

can be selected from different chapters.

6. Program Playback

(for Digital Video and VCD)

It allows you to enter the order in which

you want some chapters/tracks in

DVD/VCD to play.

1 During playback, press the PROG button to enter a program interface as follows:

2 Use the direction buttons to move cursor onto the desired place for inputting the sequence number.

3 Use the number button to input desired sequence number of title/ chapter/track with desired sequence.

4 After input your favour, press >II on remote or use the direction buttons to select play and then press OK on remote to play the programmed titles/ chapters/tracks in programmed order.

* Tap the display or press stop button to exit the PROG .

* During VCD playback, if it is in PBC ON mode, at the same time of entering the state of program playback, it turns off PBC mode.

7. Display still frame step by step

(for Digital Video and VCD)

If the unit is currently playing video, press the STEP button consecutively to display still frame step by step.

Press the PLAY button to resume normal playback.

8.Playback with Slow Speed

During video playback , press the LOC/SLOW button to execute the Slow Forward function.

Press the PLAY button to resume normal playback.

PROGR AM

Program interface for DVD

Page 26

Touch Screen Operation

3). You now hear the sound from the external device played back through the loudspeakers .

The function of the icons as follow:

Tap to mute the sound.

Tap to select EQ as the same on the remote control.

Loudness Function

Subwoofer Function

Tap to adjust audio volume.

10:00 AM10:00 AM

AUX INTERFACE 1

AUX Operation

On the front panel of this unit, there is an AUX IN jack, follow the diagram below to connect analogue replay devices(only for the Audio connect, if you want to connect the Video, please plug the <Video input > on the back of the unit .) . Use this jack to replay sound of other replay equipment such as Digital Video players, computers, etc. Via the loudspeakers.

1). Please connect the external device with stereo jack (3.5mm)plug the Aux in socket .

AUX IN JACK FRONT PANEL

AUX IN

Ground

Right

Lef t

AUX IN

2). In radio mode, touch the screen

of “ ” ICON to enter the main menu,

touch the “ AUX ” ICON to enter the

AUX IN mode.

In AUX mode, tap icon that the

display turn dark,tap twice turn dark

more, tap thrice to turn off the display,

and tap anywhere of the display to turn

it on again.

AUX INTERFACE 2

Page 27

10:00 AM10:00 AM

Touch Screen Operation

As the interface show, here is only the audio output, now tap the icon, the picture of the auxiliary input video show on the display and tap the display again to turn to audio mode.

Now you can watch the video from your External video equipment such as Digital Video players, computers, etc.

The function of the icons as follow:

Tap to mute the sound.

Tap to select EQ as the same on the remote control.

Loudness Function

Subwoofer Function

Tap to adjust audio volume.

Note: To ensure safety while driving and to comply with lows, drivers should not watch video or operate the video device while driving.

AV INTERFACE 1

AV INTERFACE 2

AV Operation

Please plug the <Video input > on the back of the unit .

Touch the AV IN icon to enter the AV IN mode. In AV mode, tap icon that the display turn dark,tap twice turn dark more, tap thrice to turn off the display, and tap anywhere of the display to turn it on again.

Page 28

Touch Screen Operation

Following the diagram below, connect your USB device to the front panel USB port . If it is properly connected, the device will be mounted and start playing automatically.

USB OPERATION

1 Current type (highlighted bar) .

2 Audio play mode select.

3 Picture play mode select.

4 Movie play mode select,

5 Current play track .

1 Current type (highlighted bar) .

2 Audio play mode select.

3 Picture play mode select.

4 Movie play mode select,

5 Current play track .

Card OPERATION

The unit can support playback MP3/WMA/ JPEG/MP4 format which are stored on SD memory cards . Please read the following instructions before you start using a memory card . Inserting the card as follow:

Insert a card, push in till heard a “CLICK”, then attach the control panel again to play.

Label side facing u pwa rd

SON G

001

002002

003

004

005

10:00AM

2 3 4

WED DING MOV 03247 .MPG

CIM G3080 .MOV

10:00AM

2 3 4

10:00 AM10:00 AM 10:00 AM10:00 AM

Page 29

10:00 AM10:00 AM

Touch Screen Operation

STEERING WHEEL CONTROL

Touch the SWC icon as follow to turn to

steering wheel control .

During setting, touch the icon to

turn to home menu.

There are 2 KEY for total 12 buttons to

save, first, tap Assign to open function

save, then select button 1 in KEY 1 on

steering wheel and tap the icon, the

icon show in button 1 position then touch

Confirm, final exit the SWC mode,

the function will save in button 1 of

KEY 1.

The function of the icons as follow:

Touch to begin function save.

After selection touch to confirm

operation.

Touch this icon to cancel the

input and resume load.

When electric resistance is too low, touch this icon to increase.

When electric resistance is too high, touch this icon to reduce.

10:00 AM10:00 AM

Page 30

Parental Control

* P

arental Control

Q: After inserting a Digital Video disc into the disc slot, ?

A: The playing disc is locked by a rating level of parental control. If the current rating level of parental control of the Digital Video player is lower than the one of current disc, you must input the correct password of parental control to unlock the parental control and enter a rating level one

* For factory preset password of parental control of Digital Video player, part of Media Setup Menu

Appendix: Parental Control

Parental Control function of a Digital Video player can control playback of movie ratings on a disc. You can set the Digital Video player to be a certain rating level of parental control using the Media Setup Menu. If the rating level of parental control of a disc is higher than the one of the Digital Vi deo player, the Digital Vi deo player cannot play the disc.

The Digital Vi deo movie can be designed so that the Digital Video player can play different versions of content of a particular movie according to the different rating levels of parental control. Depending on igital Video , the scenes that are not suitable for children will be cleared or replaced by suitable scenes automatically.

The rating levels of Parental Control are as follows:

Unlock 1 Kid Safe 2 G 3 PG 4 PG 13 5 PG R 6 R 7 NC 17 8 Adult

if a dialogue box pops up

and asks you to input a password, what should you do

equal to or higher than

of the current disc in order to play the disc.

the D features

please

see the .

Page 31

Region Code

* Region Code

Appendix: Region code of D

Motion Picture Association of America (MPAA) divided the world into 6 regions, and gave every region a region code for locking and unlocking D playback.

Please

Region codes and the countries or areas represented by region codes are as follows:

Region 1: America, Canada, East-Pacific Inlands; Region 2: Japan, West Europe, North Europe, Egypt, South Africa, Middle East; Region 3: Taiwan, Hong Kong, South Korea, Thailand, indonesia, etc.; Region 4: Australia, New Zealand, Central South America, South Pacific Inlands; Region 5: Russia, Mongolia, Indian Peninsula, Middle Asia, East Europe, North Korea, North Africa, North-west Asia etc.; Region 6: China mainland.

If you insert a disc into the disc slot and REGION ERROR is displayed, the car multi-media system can not play the disc. The reason is that the region codes of the car multi-media system and the used disc do not match each other.

igital Video

as the code of the igital Video

igital Video igital Video

impose this restriction. igital Video igital Video -

has motivated the

igital Video igital Video

Basically, a coded D player can play only the discs if its region code is the

same D player. Otherwise, it cannot play the disc.

note that only the D discs and D players produced by

the 8 biggest film-making companies of America The D

discs and D players not produced by the 8 biggest film making companies of America are not restricted by the rule of region code. Generally, they are called Free Region Code or Full Region Code.

The problems caused by area code inconsistency production of unlocked version D players and recodable D players .

South-east Asian countries include

The 8 biggest film making companies of America are as follows:

1. WarnerBros;

2. Columbia;

3. 20thCenturyFOX;

4. Paramount;

5. Universal;

6. UA(UnitedArtist);

7. MGM(MetroDogwynMayer);

8. WaltDisney

Page 32

Specification

General

Power Supply Requirement..................................................DC 12V

Current consumption........................................................10A MAX.

Maximum Power Output........................................................ 4 x 85W

Audio

Signal Output................................Front, Rear, and Subwoofer Output

Frequency Response...................................................20 Hz - 20 KHz

S/N Ratio...........................................................................90 dB (JIS)

Wow and Flutter............................................Below measurable limits

TFT Monitor

Monitor Screen Size.........................................................7 Inch Wide

Color System.....................................................................NTSC/PAL

Disc/USB/Card

Compatible Format....Digital Video/MPEG4/VCD/IMAGE/MP3/WMA/CD

Radio FM

Frequency range.....................................EUR (87.5 MHz - 108 MHz)

USA (87.5 MHz - 107.9MHz) American 1 (87.5 MHz - 108MHz) American 2 (87.5 MHz - 108MHz) OIRT(88.1 MHz - 107.9MHz)

Usable sensitivity.................................................................15dBu

I.F Frequency...................................................................10.7 MHz

AM(MW)

Frequency...............................................EUR (522 KHz - 1620 KHz)

USA (530 KHz - 1710 KHz)

American 1(530 KHz - 1720 KHz) American 2(520 KHz - 1600 KHz) OITR (531 KHz - 1602 KHz)

Usable sensitivity.................................................................40dBu

I.F Frequency....................................................................450 KHz

NOTE:

Specification and design are subject to modification, without notice, due to improvements in technology.

Page 33

Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer.

Troubleshooting

Inserting the disc in reverse direction

Press the RESET button. Front panel is not properly fixed into its place

The car ignition switch is not on

If the power supply is properly connected to the car accessory terminal,switch the ignition key to "ACC"

The fuse is blown

Replace the fuse

Presence of disc inside the player.

Remove the disc in the player, then put a new one

Insert the compact disc with the label facing upward

The disc is extremely dirty or defective

Clean the disc or try to play a new one

Temperature inside the car is too high

Cool off or until the ambient temperature return to normal

Unit has frozen up

The antenna cable is not connected

Insert the antenna cable firmly

The signals are too weak

Select a station manually

SYMPTOM CAUSE SOLUTION

Video/image appears black-white

The color system is set incorrectly

Please switch to correct color system from menu

No video/image appears

The unit is not connected to the parking brake detection switch

Make proper connection according to wire connection “ ”

The parking brake is not engaged

For safety reasons no video/ images are displayed while the vehicle is moving. Engaging the parking brake will cause images to be displayed.

Unit has become unresponsive

The radio does not work

Disc can not be loaded or ejected

No power

No color in picture

The disc format is not according to the TV-set used (PAL/NTSC)

Please choose a proper color system.

JPEG disc can not be played back

No JPEG files are recorded on the disc.

JPEG files are not recorded in a compliant format

Change the disc Record JPEG files using a compliant application

Change the disc

CAR AUDIO SYSTEMS

BOSS AUDIO CAR STEREOS