Bose CC-16 User Manual

ControlSpace® CC-16 Zone Controller

Safety Instructions

Install Guide

&

Important Safety Instructions

For the intended audience

This guide has been written for professional installers of sound systems.

1. Read these instructions – for all components before using this product.

2. Keep these instructions – for future reference.

3. Heed all warnings – on the product and in the installer’s guide.

4. Follow all instructions.

5. Do not use this apparatus near water or moisture.

6. Clean only with a dry cloth – and as directed by Bose.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources, such as radiators, heat registers, stoves or

other apparatus (including amplifiers) that produce heat.

9. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way such as: power-supply cord or plug is

damaged; liquid has been spilled or objects have fallen into the apparatus; the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped. Do not attempt to service this product yourself. Opening or removing

covers may expose you to dangerous voltages or other hazards. Please call Bose to be

referred to an authorized service center near you.

10. Do not let objects or liquids enter the product – as they may touch dangerous voltage

points or short-out parts that could result in a fire or electric shock.

11. See product enclosure for safety related markings.

12. Only use attachments/accessories specified by the manufacturer.

©2005 Bose Corporation. No part of this work may be reproduced, modified, distributed or otherwise used without prior
written permission.

2

Important Safety Instructions

Information about products that generate electrical noise

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protec-

tion against harmful interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, this is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, you are encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a different circuit than the one to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This product complies with the Canadian ICES-003 Class B specifications.

The information furnished in this install guide does not include all of the details of design,

production, or variations of the equipment. Nor does it cover every possible situation which may

arise during installation, operation, or maintenance. If you need assistance beyond the scope of

this user’s guide, please contact our Customer Service department.

3

Important Safety Instructions

Caution

Check local regulations before installing the ControlSpace®CC-16 zone controller. The

building code may require professional installation by a skilled technician or licensed

contractor. Regional electrical codes may require similar qualifications for wiring the system.

This product must be used with a Class 2 power supply.

Please read this install guide

The CC-16 zone controller is engineered to provide customized on-site controls for

ControlSpace sound systems. Please read this guide to help you install and use your

controller correctly.

Regulatory information

An example of this equipment has been tested and found to comply with the following

International Standards for Electromagnetic Compatibility:

Radiated Emissions (EU) EN55103-1

Immunity (EU) EN55103-2

Radiated Emissions (USA): FCC part 15 Class B

This Class B device meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

4

Introduction

The Bose®ControlSpace®CC-16 zone controller is an elegant wall-mounted device designed

to provide end-user control of ControlSpace systems. Custom programming allows the CC-16

to control a variety of the system elements, from switching audio sources to selecting

“scenes” or system configurations. The CC-16 features a bitmap LCD and four buttons for

displaying and controlling the system settings.

The CC-16 connects to the ControlSpace Engineered Sound Processor (ESP-88) at the

RS-485 port. Up to fifteen CC-16 units can be used per each ESP-88 to provide localized

control of the system. The maximum distance from ESP-88 to CC-16 is 2000 feet. As a

networked device, remote reprogramming is possible at any time.

Features and functions

• 122 x 32 pixel backlit blue LCD

• LCD displays volume level and

source/scene/preset setting

• Select up/down buttons for selecting

sources or scenes

• Volume up/down buttons for controlling

one or more gain controls

• IR receiver (for IR remote controls)

• RS-485 network supports up to fifteen

CC-16 units per ESP-88

• DIP-switch for specifying network

address and termination

• Universal mounting bracket

• UL and CE listed

5

Introduction

Quick start

1. Run power and network (2-wire) cables from the ESP-88 to the CC-16 mounting location

and install a mounting box.

2. Set the DIP switches to define the unit address and termination (see silkscreen on back of

CC-16).

3. Connect the power and network wires to the CC-16’s terminal block and insert unit into

the mounting box.

4. At the ESP-88, connect the network wire to the RS-485 port and connect the power

cable to a power source.

5. Run the ControlSpace®Designer software to configure and test. The CC-16 must be

connected to an ESP and configured with the ControlSpace Designer software before it

can be used. Please refer to the Designer User’s Guide for complete details on configuring

and programming the CC-16 in a ControlSpace system.

CAUTION: The building code may require professional installation by a skilled technician or

licensed contractor.

6