How it Works
Bosch
Loading...
X10
User Manual 3
124 pgs7.6 Mb0
User Manual 2
132 pgs5.05 Mb0
User Manual
12 pgs1.18 Mb0
Table of contents
Loading...

Bosch X10 User Manual 3

VideoJet X10
Network Video Server
en Installation and Operating Manual
VideoJet X10
VideoJet X10 Table of Contents | en 3

Table of Contents

1Preface 7
1.1 About this Manual 7
1.2 Conventions in this Manual 7
1.3 Intended Use 7
1.4 EU Directives 8
1.5 Rating Plate 8
2 Safety Information 9
2.1 Electric Shock Hazard 9
2.2 Installation and Operation 9
2.3 Maintenance and Repair 9
4.5 Setup Using the Configuration Manager 25
5 Configuration Using a Web Browser 27
5.13 Advanced Mode: Display Stamping 40
5.15 Advanced Mode: LIVEPAGE Functions 43
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
4 en | Table of Contents VideoJet X10
5.19 Advanced Mode: Encoder Profile 47
5.20 Advanced Mode: Audio 50
5.21 Advanced Mode: Storage Management 51
5.22 Advanced Mode: Remote Video Device 53
5.23 Advanced Mode: Recording Profiles 54
5.24 Advanced Mode: Retention Time 56
5.25 Advanced Mode: Recording Scheduler 57
5.26 Advanced Mode: Recording Status 59
5.27 Advanced Mode: Alarm Connections 59
5.28 Advanced Mode: VCA 62
5.29 Advanced Mode: VCA Profiles 63
5.30 Advanced Mode: VCA Scheduled 67
5.31 Advanced Mode: VCA Event Triggered 69
5.32 Advanced Mode: Audio Alarm 70
5.33 Advanced Mode: Alarm E-Mail 71
5.34 Advanced Mode: Alarm Task Editor 73
5.35 Advanced Mode: Alarm Inputs 74
5.36 Advanced Mode: Relay 74
5.37 Advanced Mode: COM1 76
5.38 Advanced Mode: Network 77
5.39 Advanced Mode: Advanced 80
5.40 Advanced Mode: Multicasting 81
5.41 Advanced Mode: JPEG Posting 83
5.42 Advanced Mode: Encryption 84
5.43 Advanced Mode: Maintenance 84
5.44 Advanced Mode: Licenses 86
5.45 Advanced Mode: System Overview 86
5.46 Function Test 87
6Operation 89
6.1 Operation with Microsoft Internet Explorer 89
6.2 The LIVEPAGE 91
6.3 Saving Snapshots 94
6.4 Recording Video Sequences 94
6.5 Running Recording Program 94
6.6 The RECORDINGS Page 95
6.7 Installing the Player 97
6.8 Hardware Connections Between Video Servers 98
6.9 Operation Using Software Decoders 100
7 Maintenance and Upgrades 101
7.1 Testing the Network Connection 101
7.2 Unit Reset 101
7.3 Repairs 102
7.4 Transfer and Disposal 102
8 Appendix 103
8.1 Troubleshooting 103
8.2 General Malfunctions 104
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Table of Contents | en 5
8.3 Malfunctions with iSCSI Connections 106
8.9 Communication with Terminal Program 110
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
6 en | Table of Contents VideoJet X10
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Preface | en 7
!
i

1Preface

1.1 About this Manual

This manual is intended for persons responsible for the installation and operation of the VideoJet X10. International, national and any regional electrical engineering regulations must be followed at all times. Relevant knowledge of network technology is required. The manual describes the installation and operation of the unit.

1.2 Conventions in this Manual

In this manual, the following symbols and notations are used to draw attention to special situations:
CAUTION!
This symbol indicates that failure to follow the safety instructions described may endanger persons and cause damage to the unit or other equipment. It is associated with immediate, direct hazards.
NOTICE!
This symbol refers to features and indicates tips and information for easier, more convenient use of the unit.

1.3 Intended Use

The VideoJet X10 network video server transfers video, audio and control signals over data networks (Ethernet LAN, Internet). There are various memory options for recording the images captured by the connected camera. The unit is intended for use with CCTV systems. Various functions can be triggered automatically by incorporating external alarm sensors. Other applications are not permitted. In the event of questions concerning the use of the unit which are not answered in this manual, please contact your sales partner or: Bosch Security Systems Robert-Koch-Straße 100 85521 Ottobrunn Germany www.boschsecurity.com
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
8 en | Preface VideoJet X10

1.4 EU Directives

The VideoJet X10 network video server complies with the requirements of EU Directives 89/ 336 (Electromagnetic Compatibility) and 73/23, amended by 93/68 (Low Voltage Directive).

1.5 Rating Plate

For exact identification, the model name and serial number are inscribed on the bottom of the housing. Please make a note of this information before installation, if necessary, so as to have it to hand in case of questions or when ordering spare parts.
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Safety Information | en 9

2 Safety Information

2.1 Electric Shock Hazard

– Never attempt to connect the unit to any power network other than the type for which it
is intended.
– Use only power supply units with UL approval and a power output according to LPS or
NEC Class 2. – Never open the housing. – Never open the housing of the power supply unit. – If a fault occurs, disconnect the power supply unit from the power supply and from all
other units. – Install the power supply and the unit only in a dry, weather-protected location. – If safe operation of the unit cannot be ensured, remove it from service and secure it to
prevent unauthorized operation. In such cases, have the unit checked by Bosch Security
Systems.
Safe operation is no longer possible in the following cases:
– if there is visible damage to the unit or power cables,
– if the unit no longer operates correctly,
– if the unit has been exposed to rain or moisture,
– if foreign bodies have penetrated the unit,
– after long storage under adverse conditions, or
– after exposure to extreme stress in transit.

2.2 Installation and Operation

– The relevant electrical engineering regulations and guidelines must be complied with at
all times during installation. – Relevant knowledge of network technology is required to install the unit. – Before installing or operating the unit, make sure you have read and understood the
documentation for the other equipment connected to it, such as cameras. The
documentation contains important safety instructions and information about permitted
uses. – Perform only the installation and operation steps described in this manual. Any other
actions may lead to personal injury, damage to property or damage to the equipment.

2.3 Maintenance and Repair

– Never open the housing of the VideoJet X10. The unit does not contain any user-
serviceable parts. – Never open the housing of the power supply unit. The power supply unit does not contain
any user-serviceable parts. – Ensure that all maintenance or repair work is carried out only by qualified personnel
(electrical engineers or network technology specialists).
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
10 en | Safety Information VideoJet X10
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Product Description | en 11
i

3 Product Description

3.1 Scope of Delivery

– VideoJet X10 network video server (with or without integrated hard drive) – 4 terminal blocks – Drilling template – Quick Installation Guide – Product CD with the following content:
– Quick Installation Guide
–Manual
– System Requirements document
– Further documentation on Bosch Security Systems products
– Configuration Manager
–MPEG ActiveX control
– Player and Archive Player
– DirectX control
– Microsoft Internet Explorer
– Sun JVM
– Adobe Acrobat Reader
NOTICE!
Check that the delivery is complete and in perfect condition. Arrange for the unit to be checked by Bosch Security Systems if you find any damage.
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
12 en | Product Description VideoJet X10
i

3.2 System Requirements

General Requirements
– Computer with Windows XP or Windows Vista operating system – Network access (Intranet or Internet) – Screen resolution 1,024 × 768 pixels – 16- or 32-bit color depth – Installed Sun JVM
NOTICE!
Also note the information in the System Requirements document on the product CD supplied. If necessary, you can install the required programs and controls from the product CD supplied (see Section 3.1 Scope of Delivery, page 11). The Web browser must be configured to enable Cookies to be set from the IP address of the unit. In Windows Vista, deactivate protected mode on the Security tab under Internet Options. You can find notes on using Microsoft Internet Explorer in the online Help in Internet Explorer.
Additional Configuration Requirements
– Microsoft Internet Explorer (version 6.0 or higher)
or
– Installed Configuration Manager program (version 2.0 or higher)
Additional Operational Requirements
– Microsoft Internet Explorer (version 6.0 or higher)
or
– Receiver software, for example VIDOS (version 3.11 or higher) or Bosch Video
Management System (version 2.02 or higher) or
– MPEG-4 compatible hardware decoder from Bosch Security Systems (for example
VIP XD) as a receiver and connected video monitor
– For playing back recordings: connection to storage medium
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Product Description | en 13

3.3 Overview of Functions

Network Video Server
The VideoJet X10 is a compact network video server for a connected video source. It is primarily designed for encoding video, audio and control data for transfer over an IP network. With its encoding in the MPEG-4 format, the VideoJet X10 is ideally suited for making existing analog CCTV cameras IP-compatible and for remote access to digital VCRs and multiplexers. The use of existing networks means that integration with CCTV systems or local networks can be achieved quickly and easily. Two units, for example a VideoJet X10 as a sender and a VIP XD as a receiver, can create a standalone system for data transfer without a PC. Video images from a single sender can be received simultaneously on multiple receivers. Audio signals can also be transmitted from and to compatible units. The VideoJet X10 features industrial standard, robust equipment and is therefore equally suited to stationary as well as mobile use in rail or other vehicles.
Receiver
Compatible MPEG-4 enabled hardware decoders (for example the VIP XD) can be used as receivers. Computers with decoding software such as VIDOS or computers with the Microsoft Internet Explorer Web browser can also be used as receivers.
Video Encoding
The VideoJet X10 uses the MPEG-4 and H.264 video compression standards. Thanks to efficient encoding, the data rate remains low even with high image quality and can also be adapted to local conditions within wide limits.
Dual Streaming
Dual Streaming allows the incoming data stream to be encoded simultaneously according to two different, individually customized profiles. This feature creates two data streams that can serve different purposes, for example one for recording and one optimized for live transmission over the LAN.
Multicast
In suitably configured networks, the multicast function enables simultaneous real-time video transmission to multiple receivers. The UDP and IGMP V2 protocols must be implemented on the network for this function.
Encryption
The VideoJet X10 offers a variety of options for protection against unauthorized reading. Web browser connections can be protected using HTTPS. You can protect the control channels via the SSL encryption protocol. With an additional license, the user data itself can be encrypted.
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
14 en | Product Description VideoJet X10
Remote Control
For remote control of external units such as pan or tilt heads for cameras or motorized zoom lenses, control data is transmitted via the VideoJet X10's bidirectional serial interface. This interface can also be used to transmit transparent data.
Tamper Detection and Motion Detectors
The VideoJet X10 offers a wide range of configuration options for alarm signaling in the event of tampering with the connected camera. An algorithm for detecting movement in the video image is also part of the scope of delivery and can optionally be extended to include special video analysis algorithms.
Snapshots
Individual video frames (snapshots) can be called up as JPEG images by the VideoJet X10, stored on the computer's hard drive or displayed in a separate browser window.
Recordings
Various local memory options enable the VideoJet X10 to be used as a digital VCR. The VideoJet X10 supports ANR technology, which guarantees seamless recording without gaps via VIDOS-NVR, even during network failures. A connection to an appropriately configured iSCSI system enables long-term recordings with high image quality over the network.
Backup
A function for storing the video images displayed on the hard drive of your computer is available on the LIVEPAGE as well as on the RECORDINGS page. Video sequences can be stored by means of a mouse click and can be redisplayed using the Player supplied as part of the scope of delivery.
Integrated Network Switch
The integrated switch functionality of the VideoJet X10 permits the ETH 1, ETH 2 and SFP interfaces to be used alternatively, redundantly or for cascading other units.
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Product Description | en 15
Summary
The VideoJet X10 provides the following main functions: – Video and data transmission over IP data networks – Dual Streaming function for the encoder for simultaneous encoding with two individually
definable profiles – Multicast function for simultaneous image transmission to multiple receivers – One analog BNC composite video input (PAL/NTSC) – Video encoding to international standard MPEG-4 – Two redundant integrated Ethernet ports (10/100 Base-T) – SFP slot for mini-GBIC modules (1 Gbps) – Integrated switch functionality – CF slot for CompactFlash cards for local storage – Optional, integrated robust hard drive for local storage – USB interfaces for future WAN or WLAN connections – Transparent, bidirectional data channel via RS-232/RS-422/RS-485 serial interface – Configuration and remote control of all internal functions via TCP/IP, also secured via
HTTPS – Password protection to prevent unauthorized connection or configuration changes – Extensive, flexible storage options – Four alarm inputs and four relay outputs – Built-in video sensor for motion and tamper alarms – Event-controlled automatic connection – Convenient maintenance via uploads – Flexible encryption of control and data channels – Authentication according to international standard 802.1x – Transmission and receipt of audio signals – Bidirectional audio (mono) for line connections – Audio encoding to international standard G.711
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
16 en | Product Description VideoJet X10

3.4 Connections on the Front Panel

1USB 1/2 interfaces
for future expansion of functions
2VideoIn video input
BNC socket for connecting the video source
3 Audio In audio line input
3.5 mm stereo socket for connecting an audio line input signal
4 Audio Out audio line output
3.5 mm stereo socket for connecting an audio line output signal
5 Connect LED
flashes green when the unit is connected to a video
6HDD LED
flashes orange when hard drive activity is detected (only on units with a hard drive installed)
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Product Description | en 17
i

3.5 Connections on the Rear Panel

7ETH1 RJ45 socket
for connecting to an Ethernet LAN (local network), 10/100 MBit Base-T
8ETH1 LED
lights up yellow when the unit is connected to the network via ETH 1
9ETH2 RJ45 socket
for a redundant connection to the network or to an iSCSI system
10 ETH 2 LED
lights up yellow when the unit is connected to the network via ETH 2
11 Terminal block
for alarm inputs, relay outputs, serial interface and power supply
12 Power On LED
lights up green when ready for operation
13 Factory reset button
to restore factory default settings
14 Compact Flash slot
for a CF card type I or type II
15 SFP LED
lights up yellow when the unit is connected via SFP
16 SFP slot
for mini-GBIC module
NOTICE!
For more information about the LEDs, see Section 8.4 LEDs, page 107. For terminal block assignment, see Section 8.8 Terminal Block, page 109.
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
18 en | Product Description VideoJet X10
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Installation | en 19
!
!

4 Installation

4.1 Preparations

The VideoJet X10 features industrial standard equipment and is therefore suitable for both stationary installation and mobile installation in vehicles.
CAUTION!
The unit is intended for use indoors or in housings. Select a suitable location for installation that guarantees to meet the environmental conditions. The ambient temperature must be between –30 and +60 °C (–22 and +140 °F). The relative humidity must not exceed 95%. The VideoJet X10 generates heat during operation, so you should ensure that there is adequate ventilation and enough clearance between the unit and heat-sensitive objects or equipment.
Please ensure the following installation conditions: – Do not install the unit close to heaters or other heat sources. Avoid locations exposed to
direct sunlight. – Allow sufficient space for running cables. – Ensure that the unit has adequate ventilation. – When making connections, use only the cables supplied or use appropriate cables
immune to electromagnetic interference. – Position and run all cables so that they are protected from damage, and provide
adequate cable strain relief where needed. – Avoid impacts, blows and severe vibrations that exceed the specification limits (see
Section 9 Specifications, page 113), as these can irreparably damage the unit.

4.2 Mounting

The VideoJet X10 can be permanently mounted to walls, below ceilings or other load-bearing locations using the four drillings in the unit's base.
CAUTION!
The front panel of the VideoJet X10 (video input) must not be pointing upwards, as internal heat dissipation is not guaranteed in this position. All other installation positions are permitted. Make sure that the mounting location (for example wall or ceiling) can reliably hold the unit. The load bearing capacity must be adequate for four times the weight of the unit. For mounting on metal, use screws with the following minimum specification: M4 × 8, 8.8, DIN ISO 4017. For mounting on concrete, use screws with the following minimum specification: M4 × 40 mm (1.57 in) and 6 mm (0.23 in) plastic dowels, for example fischer S4, type 50106.
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
20 en | Installation VideoJet X10
i

4.3 Connections

Camera
You can connect a video source to the VideoJet X10. Any cameras and other video sources that produce a standard PAL or NTSC signal are suitable.
1. Connect the camera or another video source to the BNC Video In socket using a video cable (75 Ohm, BNC plug).
2. If the video signal is not looped through, termination is performed by a software setting if necessary (see Section 5.17 Advanced Mode: Video Input, page 45).
Audio Connections
The VideoJet X10 has two audio ports for audio line signals. The audio signals are transmitted two-way and in sync with the video signals. As a result, you can connect a speaker or door intercom system at the destination point, for example. The following specifications should be complied with in all cases.
1 × Line In: Impedance 9 kOhm typ., 5.5 V
1 × Line Out: Impedance 10 kOhm typ., 3.0 V
impedance 16 Ohm min., 1.7 V
The stereo plugs must be connected as follows:
Contact Line In function Line Out function
Tip Channel 1 Channel 1
Middle ring – –
Lower ring Ground Ground
1. Connect an audio source with line level to the Audio In socket of the VideoJet X10 with a
3.5 mm stereo plug.
2. Connect a unit with line-in connection to the Audio Out socket of the VideoJet X10 with a
3.5 mm stereo plug.
Network
You can connect the VideoJet X10 to a 10/100 Base-T network using a standard UTP category 5 cable with RJ45 plugs. The second Ethernet interface can be used to create a redundant connection to the network.
NOTICE!
You cannot create a connection to a second network.
max. input voltage
p-p
max. output voltage,
p-p
max. output voltage
p-p
1. Connect the VideoJet X10 to the network via the ETH 1 socket.
2. Connect the VideoJet X10 to a redundant switch or hub on the same network via the ETH 2 socket.
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Installation | en 21
!
i
i
!
SFP Slot
You can establish an additional network connection by inserting a mini-GBIC module into the SFP slot for example via fiber optic cables (OF).
CAUTION!
Only laser class 1 transceivers are approved for use in the VideoJet X10. Use only approved modules.
Direct iSCSI Connection
You can connect the VideoJet X10 directly to an iSCSI system via one of the network interfaces. For ETH 1 or ETH 2 connections, use a UTP category 5 network cable with RJ45 plugs.
NOTICE!
You can obtain a list of compatible iSCSI systems from your supplier or directly from Bosch Security Systems. This list is constantly being updated and extended.
CF Slot
You can insert a type I or II CompactFlash card into the Compact Flash slot to enable recordings to be saved locally. CF cards are the ideal solution for shorter storage times and temporary recordings, for example alarm recordings or local buffering in the event of network interruptions.
NOTICE!
You can obtain a list of compatible CF cards from your supplier or directly from Bosch Security Systems. This list is constantly being updated and extended.
Playing back recordings is also possible using a different VideoJet X10, a VideoJet X20 or a VideoJet X40.
CAUTION!
If the card is formatted, all existing data is deleted from the card. You should therefore check whether the CF card contains any data that needs to be backed up before it is inserted.
1. Carefully slide the CF card, top side down, into the slot as far as it will go.
2. To remove the CF card, push the eject button to its right and then take out the card.
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
22 en | Installation VideoJet X10
!
i
i
Data Interface
The bidirectional data interface is used to control units connected to the VideoJet X10, such as a dome camera with a motorized lens. The connection supports the RS-232, RS-422 and RS-485 transmission standards. The VideoJet X10 offers the serial interface via the orange terminal block (see Section 8.8 Terminal Block, page 109). The range of controllable equipment is expanding constantly. The manufacturers of the relevant equipment provide specific information on installation and control.
CAUTION!
Please take note of the appropriate documentation when installing and operating the unit to be controlled. The documentation contains important safety instructions and information about permitted uses.
NOTICE!
A video connection is necessary to transmit transparent data.
Alarm Inputs
The VideoJet X10 has four alarm inputs on the orange terminal block (see Section 8.8 Terminal Block, page 109). The alarm inputs are used to connect to external alarm devices such as door
contacts or sensors. With the appropriate configuration, an alarm sensor can automatically connect the VideoJet X10 to a remote location, for example. A zero potential closing contact or switch can be used as the actuator.
NOTICE!
If possible, use a bounce-free contact system as the actuator.
X Connect the lines to the appropriate terminals on the orange terminal block (IN1 to IN4)
and check that the connection is secure.
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Installation | en 23
!
Relay Outputs
The VideoJet X10 has four relay outputs for switching external units such as lamps or alarm sirens. You can operate these relay outputs manually while there is an active connection to the VideoJet X10. The outputs can also be configured to automatically activate sirens or other alarm units in response to an alarm signal. The relay outputs are also located on the orange terminal block (see Section 8.8 Terminal Block, page 109).
CAUTION!
A maximum load of 30 V and 2 A (SELV) may be applied to the relay contacts.
X Connect the lines to the appropriate terminals on the orange terminal block (R1 to R4)
and check that the connection is secure.
Remote Indication of the Connection Status
When the VideoJet X10 is connected to a video, the Connect LED on the front panel of the unit flashes. The LED also provides information on the operational state of the unit and signals a unit defect (see Section 8.4 LEDs, page 107). You can connect an additional two-color LED to the VideoJet X10 as a remote indicator. This provides the same information as the integrated Connect LED. A remote indicator can be useful if the VideoJet X10 is installed at a location that is difficult to access or see, for example in a cable duct or on top of a mast. Just like the integrated LED, the remote indicator LED should also light up red and green in order to avoid confusion. Please comply with the following specifications and the connection diagram:
Voltage between RM1 and RM2 3.3 V DC max.
Current between RM1 and RM2 25 mA max.
Source resistance 140 Ohm typ.
1. Connect the LED lines to the appropriate terminals on the orange terminal block (RM1 and RM2) and check that the connection is secure.
2. Check that the signals on the Connect LED on the VideoJet X10 and the remote indicator LED correspond.
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
24 en | Installation VideoJet X10
!
i
Backup Power Supply
When used in mobile vehicles (for example public transport), the VideoJet X10 is usually switched on when the vehicle is started with the ignition key. If the ignition is switched off, the power supply to the unit is also stopped. To keep the internal clock running when the engine is off, you can connect the VideoJet X10 directly to the car battery via the BP and GND contacts. The correct time is crucial for evaluating local recordings.
CAUTION!
Connect only batteries with the following specification: 10 to 30 V DC, 50 Ah max., 12/24 V continuous flow.
1. Connect the + (plus) line on the car battery to the BP terminal on the orange terminal block.
2. Connect the – (minus) line on the car battery to the GND terminal on the orange terminal block.
3. Now check that the connections are secure.
NOTICE!
If you do not connect a battery to the unit, you should specify a time server to ensure correct system time.
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Installation | en 25
!
i

4.4 Power On/Power Off

Power Supply
The VideoJet X10 does not have a power switch. Power is supplied via a separate unit. Connect the VideoJet X10 to the power supply unit and plug this into the mains. The unit is now ready for use. The VideoJet X10 does not come supplied with a power supply unit.
CAUTION!
Use only power supply units with UL approval and a power output according to LPS or NEC Class 2. Where necessary, use suitable equipment to ensure that the power supply is free from interference such as voltage surges, spikes or voltage drops. Do not connect the VideoJet X10 to the power supply until all other connections have been made.
1. Plug the terminal block with the PSU cable connected to it into the orange socket on the VideoJet X10.
2. Connect the power supply unit to the mains. The VideoJet X10 is ready for use as soon as the Connect LED changes from a red light, indicating the start-up procedure, to a green light.
If the network connection has been set up correctly, the yellow ETH 1 or ETH 2 LED will also light up. A flashing ETH 1 or ETH 2 LED signals that data packages are being transmitted over the network.

4.5 Setup Using the Configuration Manager

The Configuration Manager program can be found on the product CD contained in the scope of delivery. This program allows you to implement and set up new video servers in the network quickly and conveniently.
NOTICE!
Using the Configuration Manager to set all parameters in the VideoJet X10 is an alternative to configuration by means of a Web browser, as described in chapter 5 of this manual.
Installing the Program
1. Insert the CD into the computer's CD-ROM drive.
2. If the CD does not start automatically, open the Configuration Manager directory using Windows Explorer and double-click Setup.exe.
3. Follow the on-screen instructions.
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
26 en | Installation VideoJet X10
i
Configuring the VideoJet X10
You can start the Configuration Manager immediately after installation.
1. Double-click the icon on the desktop or start the program via the Start menu. After the program has started, the network is immediately searched for compatible video servers.
2. You can start the configuration if a VideoJet X10 is shown in the list in the left section of the window. To do this, right-click the entry for the unit.
3. Click Unit network settings... in the popup menu.
4. In the Unit IP address field, enter a valid IP address to operate on your network (for example 192.168.0.10) and click OK. The unit reboots and the IP address is valid.
5. If required, enter an appropriate subnet mask for the IP address, and additional network data.
NOTICE!
You must reboot to activate the new IP address, a new subnet mask or a gateway IP address.
Reboot
You can trigger the reboot directly with the assistance of the Configuration Manager. X Right-click the entry for the unit in the list in the left section of the window and select the
Reset command from the context menu.
Additional Parameters
You can check and set additional parameters with the assistance of the Configuration Manager. You can find detailed information on this in the documentation for this program.
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Configuration Using a Web Browser | en 27
i

5 Configuration Using a Web Browser

5.1 Connecting

The integrated HTTP server in the VideoJet X10 provides you with the option to configure the unit over the network with a Web browser. This option is an alternative to configuration using the Configuration Manager program and is considerably richer in function and more convenient than configuration using the terminal program.
System Requirements
– Computer with Windows XP or Windows Vista operating system – Network access (Intranet or Internet) – Microsoft Internet Explorer (version 6.0 or higher) – Screen resolution 1,024 × 768 pixels – 16- or 32-bit color depth – Installed Sun JVM
NOTICE!
Also note the information in the System Requirements document on the product CD supplied. If necessary, you can install the required programs and controls from the product CD supplied (see Section 3.1 Scope of Delivery, page 11). The Web browser must be configured to enable Cookies to be set from the IP address of the unit. In Windows Vista, deactivate protected mode on the Security tab under Internet Options. You can find notes on using Microsoft Internet Explorer in the online Help in Internet Explorer.
Installing MPEG ActiveX
Suitable MPEG ActiveX software must be installed on the computer to allow the live video images to be played back. If necessary, you can install the program from the product CD supplied.
1. Insert the product CD into the computer's CD-ROM drive. If the CD does not start automatically, open the root directory of the CD in Windows Explorer and double-click MPEGAx.exe.
2. Follow the on-screen instructions.
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
28 en | Configuration Using a Web Browser VideoJet X10
Establishing the Connection
Before you can operate the VideoJet X10 within your network, it must have a valid IP address for your network and a compatible subnet mask. The following default address is preset at the factory: 192.168.0.1
1. Start the Web browser.
2. Enter the IP address of the VideoJet X10 as the URL. The connection is established and after a short time you will see the LIVEPAGE with the video image.
Maximum Number of Connections
If you do not connect, the unit may have reached its maximum number of connections. Depending on the unit and network configuration, each VideoJet X10 can have up to 25 Web browser connections or up to 50 connections via VIDOS or Bosch Video Management System.
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
VideoJet X10 Configuration Using a Web Browser | en 29
i
!
Protected VideoJet X10
If the VideoJet X10 is password protected against unauthorized access, the Web browser displays a corresponding message and prompts you to enter the password when you attempt to access protected areas.
NOTICE!
The VideoJet X10 offers the option to limit the extent of access using various authorization levels (see Section 5.11 Advanced Mode: Password, page 38).
1. Enter the user name and associated password in the corresponding text fields.
2. Click OK. If the password is entered correctly, the Web browser displays the page that was called up.
Protected Network
If a RADIUS server is employed in the network for managing access rights (802.1x authentication), the VideoJet X10 must be configured accordingly, otherwise no communication is possible. To configure the unit, you must connect the VideoJet X10 directly to a computer using a network cable. This is because communication via the network is not enabled until the Identity and Password parameters have been set and successfully authenticated (see Section Authentication, page 81).

5.2 Configuration Menu

The SETTINGS page provides access to the configuration menu, which contains all the unit's parameters arranged in groups. You can view the current settings by opening one of the configuration screens. You can change the settings by entering new values or by selecting a predefined value from a list field. There are two options for configuring the unit or checking the current settings: – Basic mode – Advanced mode In Basic Mode the most important parameters are arranged in seven groups. This allows you to change the basic settings with just a few entries and then put the device into operation. Advanced Mode is recommended for expert users or system support personnel. You can access all unit parameters in this mode. Settings that affect the fundamental functionality of the unit (such as firmware updates) can only be altered in the advanced mode. All parameter groups are described in this chapter in the order in which they are listed in the configuration menu, from the top of the screen to the bottom.
CAUTION!
The settings in the advanced mode should only be processed or modified by expert users or system support personnel.
All settings are backed up in the VideoJet X10 memory so they are not lost even if the power fails.
Bosch Security Systems Installation and Operating Manual DOC | V4.0 | 2009.06
30 en | Configuration Using a Web Browser VideoJet X10
!
Starting Configuration
X Click the SETTINGS link in the upper section of the window. The Web browser opens a
new page with the configuration menu.
Navigation
1. Click one of the menu items in the left window margin. The corresponding submenu is displayed.
2. Click one of the entries in the submenu. The Web browser opens the corresponding page.
Making Changes
Each configuration screen shows the current settings. You can change the settings by entering new values or by selecting a predefined value from a list field.
X After each change, click Set to save the change.
CAUTION!
Save each change with the associated Set button. Clicking the Set button saves the settings only in the current field. Changes in any other fields are ignored.
DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Systems
Loading...
+ 94 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use