en Installation Manual
Integrated IR Bullet Camera
WZ16
WZ16 Integrated IR Bullet Camera Table of Contents | en 3
Table of Contents
1 Safety 4
1.1 Safety Precautions 4
1.2 Important Safety Instructions 4
1.3 Important Notices 5
1.4 FCC & ICES compliance 7
1.5 CSA certication 8
1.6 Warranty / Limitation of Liability 8
2 Introduction 10
2.1 Parts Included 10
3 Installation and Connection 11
4 Conguration 13
4.1 Adjusting the Zoom 13
4.2 Adjusting the Focus 13
4.3 Adjusting the Video Output Brightness 13
5 Troubleshooting 14
5.1 5.1 Troubleshooting Tips 14 14
6 Technical Specications 15
Bosch Security Systems, Inc. Installation Manual | 1.0 | 2010.12
4 en | Safety WZ16 Integrated IR Bullet Camera
1 Safety
1.1 Safety Precautions
DANGER!
High risk: This symbol indicates an imminentlyhazardous situation such as “Dangerous
Voltage” inside the product.
If not avoided, this will result in an electrical shock, serious bodily injury, or death.
WARNING!
Medium risk: Indicates a potentially hazardous situation.
If not avoided, this could result in minor or moderate bodily injury.
CAUTION!
Low risk: Indicates a potentially hazardous situation.
If not avoided, this could result in property damage or risk of damage to the unit.
1.2 Important Safety Instructions
Read, follow, and retain all of the following safety instructions. Heed all warnings on the
unit and in the operating instructions before operating the unit.
1. Read these instructions.
2. Keep this instruction.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a clean, soft, dry or moistened cloth and mild detergent solution.
7. Do not block any ventilation openings. Install in accordance with manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or
other apparatus (including ampliers) that produce heat.
9. Do not put objects inside the camera. Make sure that no metal objects or
ammable substances enter the camera. This may cause re, short-circuits and other
damages.
10. Be careful when handling the camera. To prevent damage, do not drop the camera
or subject it to strong shock or vibration.
11. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade or the third prong is provided
for your safety. If the provided plug does not t into your outlet, consult an electrician
for replacement of the obsolete outlet.
12. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the power where they exit from the apparatus.
13. Protect the camera from humidity and dust.
14. Unplug this apparatus during lightning storms or when unused for long periods of
time.
15. Use only attachments/accessories specied by the manufacturer.
16. Use only with the bracket sold with the apparatus.
17. Do not attempt to open or disassemble the camera to gain access to the internal
components. Refer all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in a way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, does
not operate normally, or has dropped. When servicing, power shall be disconnected.
| 1.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
WZ16 Integrated IR Bullet Camera Safety | en 5
18. These servicing instructions are for use by qualied service personnel only. To
reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions, unless you are qualied to do so.
1.3 Important Notices
Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The
unit may fall, causing serious injury and/or serious damage to the unit. Use only with
the cart, stand, tripod, bracket, or table specied by the manufacturer. When a cart is
used, use caution and care when moving the cart/apparatus combination to avoid injury
from tip-over. Quick stops, excessive force, or uneven surfaces may cause the cart/unit
combination to overturn. Mount the unit per the manufacturer’s instructions.
All-pole power switch - Incorporate an all-pole power switch, with a contact separation
of at least 3 mm in each pole, into the electrical installation of the building. If it is
needed to open the housing for servicing and/or other activities, use this all-pole switch
as the main disconnect device for switching off the voltage to the unit.
Camera grounding - For mounting the camera in potentially damp environments, ensure
to ground the system using the ground connection of the power supply connector (see
section: Connecting external power supply).
Camera lens - An assembled camera lens in the outdoor housing must comply and be
tested in accordance with UL/IEC60065. Any output or signal lines from the camera must
be SELV or Limited Power Source. For safety reasons the environmental specication of
the camera lens assembly must be within the environmental specication of -10 °C to
50 °C (14 °F to 122 °F). Camera signal - Protect the cable with a primary protector if the
camera signal is beyond 140 feet, in accordance with NEC800 (CEC Section 60).
Camera signal - Protect the cable with a primary protector if the camera signal is beyond
140 feet, in accordance with NEC800 (CEC Section 60).
Coax grounding:
– Ground the cable system if connecting an outside cable system to the unit.
– Connect outdoor equipment to the unit’s inputs only after this unit has had its
grounding plug connected to a grounded outlet or its ground terminal is properly
connected to a ground source.
– Disconnect the unit’s input connectors from outdoor equipment before
disconnecting the grounding plug or grounding terminal.
– Follow proper safety precautions such as grounding for any outdoor device
connected to this unit.
U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70,
provides information regarding proper grounding of the mount and supporting structure,
grounding of the coax to a discharge unit, size of grounding conductors, location of
discharge unit, connection to grounding electrodes, and requirements for the grounding
electrode.
Disposal - Your Bosch product was developed and manufactured with high-quality
material and components that can be recycled and reused. This symbol means that
electronic and electrical appliances, which have reached the end of their working life,
must be collected and disposed of separately from household waste material. Separate
collecting systems are usually in place for disused electronic and electrical products.
Please dispose of these units at an environmentally compatible recycling facility, per
European Directive 2002/96/EC.
Electronic Surveillance - This device is intended for use in public areas only. U.S. federal
law strictly prohibits surreptitious recording of oral communications.
Environmental statement - Bosch has a strong commitment towards the environment.
This unit has been designed to respect the environment as much as possible.
Bosch Security Systems, Inc. Installation Manual | 1.0 | 2010.12
6 en | Safety WZ16 Integrated IR Bullet Camera
Electrostatic-sensitive device - Use proper CMOS/MOS-FET handling precautions to
avoid electrostatic discharge.
NOTE: Wear required grounded wrist straps and observe proper ESD safety precautions
when handling the electrostatic-sensitive printed circuit boards.
Moving - Disconnect the power before moving the unit. Move the unit with care.
Excessive force or shock may damage the unit and the hard disk drives.
Outdoor signals - The installation for outdoor signals, especially regarding clearance
from power and lightning conductors and transient protection, must be in accordance
with NEC725 and NEC800 (CEC Rule 16-224 and CEC Section 60).
Permanently connected equipment - Incorporate a readily accessible disconnect device
external to the equipment.
Pluggable equipment - Install the socket outlet near the equipment so it is easily
accessible.
Power resupply - If the unit is forced to power down due to exceeding the specied
operating temperatures, disconnect the power cord, wait for at least 30 seconds, and
then reconnect the power cord.
Power lines - Do not locate the camera near overhead power lines, power circuits, or
electrical lights, nor where it may contact such power lines, circuits, or lights.
SELV - All the input/output ports are Safety Extra Low Voltage (SELV) circuits. SELV
circuits should only be connected to other SELV circuits.
Because the ISDN circuits are treated like telephone-network voltage, avoid connecting
the SELV circuit to the Telephone Network Voltage (TNV) circuits.
System ground/Safety ground
System (video) ground is indicated by the symbol
Safety (power) ground is indicated by the symbol
The system ground is only used to comply with safety standards or installation practices
in certain countries. Bosch does not recommend connecting system ground to safety
ground unless it is explicitly required. However, if the system ground and safety ground
are connected and grounding loops are causing interference in the video signal, use an
isolation transformer (available separately from Bosch).
CAUTION!
Connecting System ground to Safety ground may result in ground loops that can disrupt
the CCTV system.
Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security
Systems cannot be held liable for any damage that results from missing video
information. To minimize the risk of lost digital information, Bosch Security Systems
recommends multiple, redundant recording systems, and a procedure to back up all
analog and digital information.
.
.
| 1.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
WZ16 Integrated IR Bullet Camera Safety | en 7
1.4 FCC & ICES compliance
FCC Information
(U.S.A. and Canadian Models Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the following measures:
– Fit Ferrite beads on all cable to and from the power supply box, within the box walls.
– Route the composite cable between the camera and the power supply in steel
conduit piping over the entire run of the cable up to and including connection to a
deep conduit base tted under the camera and a conduit tting adaptor in the wall of
the PSU box.
– Reorient or relocate the receiving antenna;
– Increase the separation between the equipment and receiver;
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected;
– Consult your Bosch Service Center, dealer, or an experienced radio/TV technician
for further advice.
Intentional or unintentional modications, not expressly approved by the party
responsible for compliance, shall not be made. Any such modications could void the
user’s authority to operate the equipment. If necessary, the user should consult the
dealer or an experienced radio/television technician for corrective action.
The user may nd the following booklet, prepared by the Federal Communications
Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This
booklet is available from the U.S. Government Printing Ofce, Washington, DC 20402,
Stock No. 004- 000-00345-4.
Informations FCC et ICES
(modèles utilisés aux États-Unis et au Canada uniquement)
Suite à différents tests, cet appareil s’est révélé conforme aux exigences imposées
aux appareils numériques de classe B, en vertu de la section 15 du règlement de la
Commission fédérale des communications des États-Unis (FCC), et en vertu de la
norme ICES-003 d’Industrie Canada. Ces exigences visent à fournir une protection
raisonnable contre les interférences nuisibles lorsque l’appareil est utilisé dans le
cadre d’une installation résidentielle. Cet appareil génère, utilise et émet de l’énergie
de radiofréquences et peut, en cas d’installation ou d’utilisation non conforme aux
instructions, engendrer des interférences nuisibles au niveau des radiocommunications.
Toutefois, rien ne garantit l’absence d’interférences dans
une installation particulière. Il est possible de déterminer la production d’interférences
en mettant l’appareil successivement hors et sous tension, tout en contrôlant la
réception radio ou télévision. L’utilisateur peut parvenir à éliminer les interférences
éventuelles en prenant une ou plusieurs des mesures suivantes:
– Modier l’orientation ou l’emplacement de l’antenne réceptrice;
– Éloigner l’appareil du récepteur;
– Brancher l’appareil sur une prise située sur un circuit différent de celui du récepteur;
– Consulter le revendeur ou un technicien qualié en radio/télévision pour obtenir
de l’aide.
Bosch Security Systems, Inc. Installation Manual | 1.0 | 2010.12
8 en | Safety WZ16 Integrated IR Bullet Camera
Toute modication apportée au produit, non expressément approuvée par la partie
responsable de l’appareil, est strictement interdite. Une telle modication est
susceptible d’entraîner la révocation du droit d’utilisation de l’appareil.
La brochure suivante, publiée par la Commission fédérale des communications (FCC),
peut s’avérer utile : How to Identify and Resolve Radio-T V Interference Problems
(Comment identier et résoudre les problèmes d’interférences de radio et de
télévision). Cette brochure est disponible auprès du U.S. Government Printing Ofce,
Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4
NOTICE!
This is a class B product. In a domestic environment this product may cause radio
interference, in which case the user may be required to take adequate measures.
1.5 CSA certication
Disclaimer
CSA has not tested the performance or reliability of the security or signaling aspects
of this product. CSA has only tested re, shock and/or casualty hazards as outlined in
CSA’s Standard(s) for Safety for Audio, Video and Similar Electronic Apparatus. Safety
Requirements UL 60065. CSA Certication does not cover the performance or reliability
of the security or signaling aspects of this product. CSA MAKES NO REPRESENTATIONS,
WARRANTIES, OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR
RELIABILITY OF ANY SECURITY OR SIGNALING RELATED
FUNCTIONS OF THIS PRODUCT.
1.6 Warranty / Limitation of Liability
The Night Vision B&W & DSP Color CCD Camera has a three-year warranty.
BOSCH Security Systems warrants that its products, at the time of shipment by BOSCH
Security Systems, are free from defect in material or workmanship under normal use and
service for the respective warranty periods specied in the applicable Price Schedule or
as otherwise published. To assure conformance with operating limitations, Buyer should
refer to the applicable data sheet.
The warranty is void (i) if the Product is not operated in conformance with installation,
environmental, mechanical or electrical requirements, or within thermal stress limits, or
(ii) to the extent that any malfunction is the result of misuse, abuse, vandalism, neglect,
improper installation or application, alteration, accident, or negligence in use, storage,
transportation, or handling or if the original identication markings on the product have
been removed, defaced or altered, lightning, electricity, water, re, environment or other
hazard, or act of God, or other impact outside of normal operating guidelines.
The foregoing warranty is subject to Buyer’s (i) promptly written claim and (ii) timely
provision to BOSCH Security Systems of an opportunity to inspect and test the Product
claimed to be defective. Such inspection may be on Buyer’s premises and/or BOSCH
Security Systems may request the return of the Product at Buyer’s expense. However,
BOSCH Security Systems shall not be responsible for packing, inspection, or labor costs
in connection with the return of Product. No Product shall be accepted for warranty
service that is not accompanied by a Return Authorization issued by BOSCH Security
Systems.
| 1.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
WZ16 Integrated IR Bullet Camera Safety | en 9
The liability of BOSCH Security Systems hereunder or otherwise is solely and exclusively
limited to replacement (new or refurbished Product), repair, or credit of the amortized
purchase price, as BOSCH Security Systems may elect, for any Product which is returned
by Buyer during the applicable warranty period, or services for which timely notice of
defect has been given by Buyer, and which are found by BOSCH Security Systems to be
subject to adjustment under this warranty.
BOSCH Security Systems’ warranty shall not be enlarged, diminished, or affected by, and
no obligation or liability shall arise or grow out of BOSCH Security Systems’ rendering or
technical advice, facilities, or services in connection with Buyer’s order to the products
furnished hereunder.
For more information about the warranty on this product, see the Warranty Repair
section on Bosch’s Customer Care web page at www.boschsecurity.us/en-us/Service/
CustomerCare.
NOTICE!
Do not remove the serial sticker for the warranty service. Doing so will void the
warranty.
Bosch Security Systems, Inc. Installation Manual | 1.0 | 2010.12
10 en | Introduction WZ16 Integrated IR Bullet Camera
2 Introduction
The WZ16 Integrated IR Bullet Camera is a night vision DSP Color CCD camera that uses
a 1/3” CCD solid-state imaging device that provides superior performance. The camera
can be installed easily in most indoor and outdoor locations.
Features include:
– Day/night operation
– Infrared, photocell-controlled LEDs
– Weight of less than 1.5 pounds / 0.6 kg
– IP67 rating
– Operates at temperature range from -30 °C to +55 °C ( - 22°F to + 131°F) at up to 80%
humidity
2.1 Parts Included
Quantity Item
1 1 WZ16 Integrated IR Bullet Camera
1 Mounting bracket
3 Mounting screws
1 Installation Manual
| 1.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
WZ16 Integrated IR Bullet Camera Installation and Connection | en 11
3 Installation and Connection
DANGER!
RISK OF ELECTRIC SHOCK! DO NOT OPEN THE UNIT!
WARNING!
To prevent injury, this apparatus must be securely attached to the oor/wall in
accordance with the following installation instructions.
CAUTION!
Do not install the camera near electric or magnetic elds. If possible, do not install in a
kitchen or boiler room as heat will affect the camera.
CAUTION!
Do not use a power source other than the one specied. An unregulated power supply
can cause damage to the camera. Use of an unregulated power supply will void the
product warranty.
1. Select a mounting surface that is strong enough to support the camera.
2. Connect the camera to either a 12VDC (recommended for best picture and the most
stable camera operation) or 24 VAC regulated power supply.
3. Face the camera away from the sun or any bright or reective light. Excess light on
the lens may cause smear on the picture and possible damage to the CCD.
CAUTION!
To prevent humidity problems, the camera must be installed in dry conditions, and the
cable leads should be sealed once connected.
Figure 3.1 Camera mounted on ceiling
Bosch Security Systems, Inc. Installation Manual | 1.0 | 2010.12
12 en | Installation and Connection WZ16 Integrated IR Bullet Camera
Figure 3.2 Camera mounted (from bottom) on Wall
Figure 3.3 Camera mounted (from top) on Wall
4. Connect the camera to the video monitor. Bosch recommends using a monitor with a
CCTV quality 75Ω video impedance level. If your monitor is switched to high
impedance, please adjust the monitor accordingly.
Figure 3.4 Standard 12 VDC BNC(RCA) Connection
Number Description
1 12 VDC or 24 VAC regulated power supply
2 Video in
3 BNC (RCA) Female video
| 1.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
WZ16 Integrated IR Bullet Camera Conguration | en 13
4 Conguration
Follow the steps below to adjust the zoom and focus. Remove the lens cap before
making adjustments, then replace it when you nish. Refer to the gure below.
Figure 4.1 Lens adjustment
Number Description
1 Zoom control
2 Focus control
3 Video brightness
CAUTION!
To prevent humidity problems, the camera must be installed in dry conditions.
Removing the lens cap in a wet or humid environment may result in condensation on
the front window.
4.1 Adjusting the Zoom
1. Loosen the Zoom lock screw by turning it counterclockwise.
2. Adjust the zoom by moving the Zoom lever to Tele side or Wide side.
3. Turn the Zoom lock screw clockwise to tighten the focus lever after adjustment.
4.2 Adjusting the Focus
1. Loosen the focus lock screw by turning it counterclockwise.
2. Adjust the focus by moving the focus lever to near side or far side.
3. Turn the focus lock screw clockwise to tighten the focus lever after adjustment.
4.3 Adjusting the Video Output Brightness
1. Adjust the brightness from VR according to the environment.
Bosch Security Systems, Inc. Installation Manual | 1.0 | 2010.12
14 en | Troubleshooting WZ16 Integrated IR Bullet Camera
5 Troubleshooting
5.1 Troubleshooting Tips
Before sending the camera out for repair, check the items below. If the problem persists
after checking these items, contact your service center.
- If no image appears, verify that:
– The coaxial cable is attached securely.
– The power and voltage are normal.
– There is adequate illumination.
- If the image is unclear, verify that:
– The lens is in focus.
– The lens is not dirty. Dirt or ngerprints on the lens can adversely affect the images.
Gently wipe any dirt or ngerprints off the lens with a soft cloth or lens cleaning paper
and cleaning uid (available commercially).
– The monitor is adjusted correctly.
| 1.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
WZ16 Integrated IR Bullet Camera Technical Specications | en 15
6 Technical Specications
Electrical
Power 12 VDC (±10%) Max 700 mA
Surge Suppression
Power Input
Videos
Signal Format NTSC PAL NTSC PAL
Image Device 1/3 in. Super HAD CCD 1/3 in. Super HAD CCD II
Scanning Systems 2 : 1 Interlace
Horizontal
Resolution
Total Pixels 811 x 508 795 x 596 811 x 508 795 x 596
Effective Pixels 768 x 494 752 x 582 768 x 494 752 x 582
Signal-to-Noise Ratio > 45 dB (with AGC off)
Sensitivity/
Min. Illumination
Video Output Composite Video 1 Vpp, 75 Ohm unbalanced
IR LED 18 ea.
IR LED Wavelength 850 nm
IR Beam Range up to 20 meters
LED Operation Turn On: 2 Lux
Mechanical
Dimensions (H x W x L)
– Camera 115 mm x 60 mm x 60 mm
– Bracket 115 mm x 60 mm x 60 mm
Weight
– Camera and Bracket 0.56 kg (1.2 lbs)
Construction Robust aluminum extrusion
Color Silver gray
Finish Painted
Bracket Pan-tilt bracket included
Bracket Pan/Tilt Range Pan: ±90° (180° total)
Environmental
– Operating Temperature –10 °C to +50 °C (14 °F to 122 °F)
Storage Temperature –20 °C to +60 °C (–4 °F to 140 °F)
Operating Humidity 10% to 80% (condensing or non-condensing?)
24 VAC (±10%) Max 7 W
Peak current: 2000 A (8/20 μs)
Peak power: 5500 W (2 ms)
540 TVL
Day: .5 Lux / F2.0
Night: 0.00 Lux (IR LED On)
Turn Off: 4 Lux
(4.53 in. x 2.36 in. x 2.36 in.)
(4.53 in. x 2.36 in. x 2.36 in.)
Tilt: ±50° (100° total)
Bosch Security Systems, Inc. Installation Manual | 1.0 | 2010.12
16 en | Technical Specications WZ16 Integrated IR Bullet Camera
Dimensions
Below are several dimensional drawings of the camera. Unit of measure is mm.
Figure 6.1 Front view
Number Description
1 Photocell
18 LED
Figure 6.2 Bottom view
Figure 6.3
Side view
| 1.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
WZ16 Integrated IR Bullet Camera Technical Specications | en 17
Figure 6.4
Mounting bracket
Bosch Security Systems, Inc. Installation Manual | 1.0 | 2010.12
Bosch Security Systems, Inc.
850 Greeneld Road
Lancaster, PA 17601
U.S.A.
www.boschsecurity.com
© Bosch Security Systems, Inc., 2011
Loading...