Page 1
GE Appliances
10-1/2
28-7/8
27-1/2
29-7/8
12-1/
4
6
20
9
4
10-1/2
16
C
L
Cabinet Dimensions (in inches)
R
20
9
4
10-1/2
16
C
L
Cabinet Dimensions (in inches)
21-9/16
3
19
3-1/4
x 10
20-1/2
28-7/8
27-1/2
29-7/8
12-1/
4
6
Cooktop Dimensions (in inches)
JP389WJ/BJ – GE Select-Top™ Modular Downdraft Cooktop
Built-In Downdraft Modular Cooktop
Dimensions (in inches)
Built-In Downdraft Modular Cooktop Cabinet
Dimensions (in inches)
Receptacle Location: Install an approved
junction box within shaded area shown in
diagram. Junction box must be at least 10-1/2"
below top of cabinet.
Note: These cooktops are U.L. approved for
indoor use only.
Installation Information: Before installing,
consult installation instructions packed with
product for current dimensional data.
Listed by
Underwriters
Laboratories
Specification Created 6/04
321118
For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center
®
service, 800.626.2000.
Page 2
25
1-7/8"
MIN. Required*
20-5/8
Cut-out Dimensions (in inches)
28-7/8
*U.L. Requirement.
Note: A 6" minimum spacing to adjacent side wall is required
1-7/8"
MIN. Required*
20-5/8
Cut-out Dimensions (in inches)
28-7/8
9-3/8
15-3/4
7-9/16
Downward venting
(in inches)
2" Approx.
5" Approx.
for European
cabinets
28-7/8
9-3/8
7-9/16
Downward venting
(in inches)
25
1-7/8"
MIN. Required*
20-5/8
Cut-out Dimensions (in inches)
28-7/8
*U.L. Requirement.
Note: A 6" minimum spacing to adjacent side wall is required
9-3/8
9-3/8
15-3/4
7-9/16
Rear wall venting (in inches)
Downward venting
(in inches)
R
GE Appliances
GE Appliances
JP389WJ/BJ – GE Select-Top™ Modular Downdraft Cooktop
Cutout Dimensions (in inches)
Note: In some cabinets, the sides may need to be scooped or cut down 2" as shown and the corner
braces removed in order to accommodate the cooktop.
Preparing the Cabinet for Installation
Wall Installation: Wall installations require 25" countertop depth. When cabinet is flush against
the wall, the fan housing can be rotated to the horizontal position for direct venting through rear wall.
Make a countertop cutout that is centered in the range cabinet according to unit dimensions and
installation type. Duct hole is positioned in back of cabinet for through-the-wall ducting.
Peninsula or Island Installation: For peninsula or island installation, a minimum 26" countertop
depth is suggested. Blower should be in vertical position. Island or peninsula cabinets may require
adjustment in cutout depth and/or location within the width dimensions. Duct hole is positioned in
bottom of cabinet for island or peninsula installation.
Slab Installation: For peninsula or island installation and rear wall ducting, PVC duct or locallyapproved piping should be used if installing under a poured concrete slab.
Installing the Ductwork: Use minimum 26-gauge galvanized or 24-gauge aluminum duct in 6"
round or 3-1/4" x 10" size, or combination of both. PVC duct or locally approved piping should
be used if installing under a poured concrete slab.
Listed by
Underwriters
Laboratories
Specification Created 6/04
321118
For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center
®
service, 800.626.2000.
Page 3
GE Appliances
40
Long
Venting Options
Inside Wall
Through Roof
Direct to Outside
Straight Duct
Direct to Outside
Straight Duct
Venting Options
Inside Wall
Through Roof
Direct to Outside
Straight Duct
Between the Floor Joists
Direct to Outside
Straight Duct
Through the Cabinet Toe Space
R
JP389WJ/BJ – GE Select-Top™ Modular Downdraft Cooktop
Venting Options
KW Rating
240V
8.0
Breaker Size
40 Amps
†
Note: Check local codes for required breaker size
†
Note: Ductwork must be vented to outside. Do
not vent into a wall, ceiling, crawlspace, attic or
any concealed space. Always use an appropriate
roof or wall cap with damper. Laundry-type
wall caps should never be used. For maximum
efficiency use, the shortest and straightest duct
run possible, with as few fittings as possible.
For satisfactory performance, the duct run should
not exceed 100 feet equivalent length. Refer to
the table of equivalent lengths for various
duct configurations.
Installation Information: Before installing,
consult installation instructions packed with
product for current dimensional data.
Specification Created 6/04
321118
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center
®
service, 800.626.2000.
Page 4
GE Appliances
M
E
D
M
E
D
JP389WB/BD.EPS
JP389WJ/BJ – GE Select-Top™ Modular Downdraft Cooktop
Features and Benefits
• 30" Dual Modular Cooktop
• Infinite Heat Rotary Controls
• Powerful Downdraft Venting System
• 3-Speed Fan
• Heating Element “ON” Indicator Light
• Porcelain-Enameled Cooktop
• Optional Modules Available At Additional Cost
Specification Created 6/04
321118
• Model JP389BJ – Black on black
• Model JP389WJ – White on white
Models
Optional modules
available at additional cost JP389WJ JP389BJ
®
Calrod
modules
Ribbon modules
Grill modules
Griddle Accessory
Grill Cover
JXDC44RWH JXDC43RBL
JXDR50VW JXCDR50VB
JXDL44N JXDL44N
JXDD44R JXDD44R
JXDM3 JXDM2
Loading...